Microtek ScanMaker i800 Plus User manual

Brand: Microtek

Model: ScanMaker i800 Plus

Type: User manual

Step 2: Install Software

Start Here

Installing your Microtek ArtixScan F2

Important: Do not remove the yellow stickers from your scanner

until you are told to do so.

You must install software before connecting your scanner. Always

close any open programs, and turn off Anti-virus utilities before

installing software.

PC:

A. Place the Adobe DVD into a drive, and

install the software. Skip this step if you

have a newer version of Photoshop

Elements already installed on your

computer.

B. Place the Microtek Software CD/DVD into a

drive, and follow the on-screen instructions

to install the scanner driver and software.

C. Restart your computer at the end of all

software installation.

NOTE: If the Microtek Software Installer screen does not come

up automatically, double-click the following in succession: “My

Computer”; the CD/DVD-ROM icon; then cdsetup.exe to start the

installer program.

Step 1: Unpack Contents

Unpack your scanner package and check

for major components.

1. ArtixScan F2 scanner

2. Hi-Speed USB cable

3. Power cord

4. Vinyl Strips

5. Software CDs/DVDs

6. Film holders

I49-004847 D, March 2015

MAC:

A. Place the Adobe DVD into a drive, and install

the software. Skip this step if you have a

newer version of Photoshop Elements already

installed on your computer.

B. Place the Microtek Software CD/DVD

(ScanPotter) into a drive, and double-click the

ScanPotter installer icon to install ScanPotter.

C. Install the remaining software components,

then restart your computer at the end of all

software installation.

NOTE: After rebooting your Macintosh, the Microtek software will

attempt to locate your scanner on the system. Since this is your

first install and you have not yet connected the scanner, simply

ignore the message that appears and proceed to the next step.

Step 3: Unlock Scanner

A. Remove the yellow “Step 3” sticker from your scanner.

B. With the scanner power off, tilt the front right corner of

the scanner to see the locking screw at the bottom.

C. Using a screwdriver, push and turn the locking screw

counterclockwise to the unlock position. When

successfully unlocked, the screw will push out a little,

protruding slightly from the bottom of the scanner.

Step 4: Connect Scanner

To the power adapter

A. Remove the yellow “Step 4” sticker from your scanner.

B. Connect the power cord to the back of the scanner.

C. Plug the power cord into a power source.

To the Hi-Speed USB cable

D. Connect one end of the cable to your computer.

E. Connect the other end of the cable to the scanner.

Power button

F. Press the power button at

the front panel of your

scanner, and wait for the

lights to stop blinking and

stay on steady.

The system will detect

your scanner

automatically.

NOTE: To lock the scanner (for shipping and other reasons), refer to

the ArtixScan F2 Supplement in the Microtek software CD/DVD.

Position the Scan Material

Position Transparencies

A. To scan standard-size transparent film such as 35mm slides, 35mm filmstrips, 4” x 5” film, or

medium format up to 6 x 17-cm panoramic film: Use the individual film holders provided with

the scanner together with the Main Holder. The entire assembly is then inserted into the lower

compartment (transparency bay) of the scanner. Make sure that the Main Holder is inserted

correct side up.

Using the 35mm Slide Holder with

the Main Holder

Make sure that the red

arrow marks on both

the 35mm Slide Holder

and the Main Holder

are pointing to each

other when the holders

are put together

Assembling the 35mm

Filmstrip Holder with the Main

Holder

Assembling the 4” x 5” Film

Holder with the Main Holder

Assembling the 6 x 22-cm Film

Holder with the Main Holder

B. To scan non-standard-size

transparent film, use the Glass

Holder. Place the film to be

scanned face down on top of the

Glass Holder. Secure the film to

the glass surface if needed with

the vinyl strips provided, and

insert the Glass Holder into the

lower compartment (transparency

bay) of the scanner. Make sure the

Glass Holder is inserted correct

side up.

Calibration strip

(Keep clear and unobstructed)

Calibration strip (Keep clear and unobstructed)

The correct side up is the side showing

the holder labels facing up

The correct side up is the side showing

the holder labels facing up

Position Reflective Materials

To scan reflective materials such as photos: Raise

the scanner lid, and place the original to be scanned

face down on the scanner glass bed, towards the

front of the scanner. Center the top of the original

along the horizontal ruler of the scanner. Close the

lid, and prepare to scan.

Position the Scan Material (cont.)

ScanWizard Pro (for PC Users Only)

Preview window when

scanning photos (reflectives)

Settings window

Info window

Scan Job Queue window

ScanWizard Pro is the scanner controller software

for the ArtixScan F2. The four windows of

ScanWizard Pro are shown here to familiarize you

with the interface and to prepare you for the

material in the next section on “Scanning.”

ScanWizard Pro can be launched as a stand-alone

by clicking the program icon, or it can be

launched by using the File-Import or File-Acquire

command from your image-editing program.

ScanPotter (for Mac Only)

ScanPotter is scanning software developed

exclusively for ArtixScan F2 running on a Mac

system. ScanPotter has a unique and clean interface

that users will find productive and easy to use.

Basic Scanning for PC Users

Scanning Photos

1. Insert the holder with the loaded film into the transparency bay of the scanner, as detailed in the

“Position the Scan Material” section in this guide.

2. Launch ScanWizard Pro as a stand-alone by clicking on the program icon on the desktop.

• If asked to calibrate your scanner, you can skip this section for now and come back to it later.

Or, if you wish to perform calibration, see the ArtixScan F2 Supplement in the Microtek

software CD/DVD for more details.

• If prompted to set up Color Matching, click OK for now to accept the settings. You can

always change the settings at a later time. For more details, see the ArtixScan F2 Supplement

in the Microtek Software CD/DVD.

3. In the Preview window of ScanWizard Pro, choose Reflective from the Scan Material menu.

4. Click the Overview button in the Preview window to see a preliminary scan of the image.

5. Select the Scan Frame tool, and choose the area to be scanned by sizing the marquee around the

targeted area.

6. Select the Auto Focus tool, and choose the area to be applied with the AF function by dragging a

rectangle around it.

7. Specify your scanning requirements in the Settings window. Choose the desired image type and

resolution, and adjust the scan frame settings if necessary.

8. Adjust image quality if necessary, using the Advanced Image Correction tools.

9. Click the Scan (or “Batch”) button in the Preview window to start scanning.

Preview window when

scanning positives

Preview window when

scanning negatives

Scanning Positive or Negative Film

1. Insert the holder with the loaded film into the transparency bay of the scanner, as detailed in the

“Position the Scan Material” section in this guide.

2. Launch ScanWizard Pro.

3. If scanning positive film such as 35mm slides:

a) Go to the Preview window of ScanWizard Pro and from the Scan Material menu, choose

Positive / Positive Film.

b) Follow steps 4 to 8 of the procedures detailed in “Scanning Photos” (the first column in this

section).

If scanning negatives:

a) Go to the Preview window of ScanWizard Pro and from the Scan Material menu, choose

Negative / Negative Film. The Negative Scan Settings window appears.

b) Go to the Negative Scan Settings window, choose the film brand, film type, and ISO settings

that match the film you use. For more details, refer to a PDF document called “ScanWizard

Pro Reference Manual” in your Microtek Software CD/DVD and see the Addendum to

ScanWizard Pro section.

c) Follow steps 4 to 8 of the procedures detailed in “Scanning Photos” (the first column in this

section).

4. To complete the scan, click the Scan (or “Batch”) button in the Preview window to start

scanning.

Basic Scanning for PC Users (cont.)

Basic Scanning for Mac Users

1. Place the scan material.

• To scan a photo, place the photo on the upper glass bed, as detailed in the “Position the

Scan Material” section in this guide.

• To scan film, insert the holder with the loaded film into the transparency bay of the scanner,

as detailed in the “Position the Scan Material” section in this guide.

2. Launch ScanPotter as a stand-alone by clicking on the program icon, or by selecting it from the

application folder in your Mac OS X system.

3. In the Scan Source options menu, depending on the scan material you are using, choose either

Reflective for photos, Negative Film for negatives, or Positive Film for transparencies and slides.

4. Specify your scanning requirements in the Scanner Settings column.

a) Select the appropriate image type (e.g., RGB Color) in the Color Type as your image output

type.

- Select Color to scan the image in color.

- Select Grayscale to scan the image in grayscale.

- Select Black & White to scan the image in black-and-white.

b) Select a desired resolution in the Resolution for your image output resolution.

c) Select Automatic Detection or a desired dimension in the Scan Frame as your preview image

size.

5. Click the Preview button to perform a preliminary scan of the image in the Preview window.

6. If necessary, resize the scan frame (floating dotted rectangle) around the image by dragging on

the square spots on the edge or on the corner of the scan frame to determine the final size of the

actual scan.

7. If necessary, specify file settings for your output image files, using the options offered in the File

Saving Settings column.

8. If necessary, click the Image Settings button to switch to a window in which you can select a

preset image effect to the image directly or adjust image quality manually by using the additional

image correction tools.

9. Click the Scan button to start scanning.

NOTE: For details on scanning photos and film, see the ArtixScan F2 Supplement in the Microtek software

CD/DVD.

Basic Scanning for Mac Users (cont.)

Click the Image Settings

button to switch to a

window where contains

a composite display of

nine-image-effects (Filter

column) and additional

image correction tools

(Additional Adjustment

column) for your

scanned image.

Click the Scan Settings button

to switch back to the default

control panel of ScanPotter

Scan frame

(enclosed by dotted lines)

Preview window when

scanning slides

Preview

window when

scanning

photos

Calibration

All Off - Scanner is off

Flashing Orange - Warming up

All On - Ready to scan

Problems?

The orange and green LEDs on the front of the

scanner indicate the status of the scanner. On

power up, you should see the following:

First, make sure that you have followed installation

steps 1 through 4. If your problem is listed here, try

the suggested solution.

1. No light comes on when the scanner is turned on.

Make sure your scanner is connected to your

computer and plugged into a power source.

2. Add/Remove Hardware Wizard appears on your

screen.

Click the “Cancel” button and close the Control

Panel. Disconnect the USB cable from the back of

your computer, and refer to the installation

instructions in this guide.

3. When trying to scan, an error message appears on

your screen that reads, “Can’t Find Scanners”.

Make sure your scanner is unlocked (see Step 3).

Make sure your scanner is connected to your

computer and plugged into a power source (see Step

4).

Uninstall and reinstall the ScanWizard Pro or

ScanPotter software.

4. After clicking scan, a blank screen appears.

Make sure your scanner is unlocked (see Step 3).

Uninstall and reinstall the ScanWizard Pro or

ScanPotter software.

5. Having trouble scanning negatives or slides?

Make sure that you have properly inserted the Main

Holder or the Glass Holder, as indicated in Steps A

and B of the “Position the Scan Material” section of

the Start Here guide.

From the Preview window of ScanWizard Pro, choose

Positive or Negative from the Scan Material menu.

From the ScanPotter, go to the Scanner Settings

column, then click the Scan Source drop-down menu

to select either the Positive Film or Negative Film

option.

Make sure that the calibration strip is unobstructed.

For location of the calibration strip, see Steps A and B

of the “Position the Scan Material” section of the

Start Here guide.

Uninstall and reinstall the ScanWizard Pro or

ScanPotter software.

NOTE: This section is only available for the PC users who have installed the Microtek’s MSP utility,

and use the IT8 color targets to generate scanner ICC profiles.

The Microtek Scanner ICC Profiler (MSP) program

included with your ArtixScan F2 is used to calibrate

your scanner to achieve consistent and accurate color.

Two industry-standard IT8 color targets are included

with the SilverFast Ai Studio software kit: a Reflective

target to calibrate the upper scan bed for scanning

photos; and a Transparency target to calibrate the

lower scan bed for scanning film.

You will be asked to calibrate your scanner the first

time you run ScanWizard Pro to try to scan. You may

skip calibration to proceed directly to scanning, and

then choose to come back at a later time to perform

calibration.

Reflective

target

Transparency

target

For more details on calibration, refer to the section “Using the

Microtek Scanner ICC Profiler (MSP)” in the ArtixScan F2

Supplement in the Microtek software CD/DVD.

Do You Need Assistance?

Manuals

If you have additional questions and need further instruction or information, we provide electronic

manuals for:

1. Using your ArtixScan F2 (Supplementary information)

2. Using the ScanWizard Pro or ScanPotter scanning software

3. Using the bundled third-party software

To access the electronic manuals: Insert the scanner’s software CD/DVD into your computer’s CD/

DVD-ROM drive. Next, locate and click the “Manuals” option when the software installer window

appears on your screen. Finally, select and click the title of the manual you wish to view.

Missing Items

If your package is missing items, please call Microtek Customer Service.

Drivers & Software Upgrades

After you finish the installation of software, if you found that the installed drivers and software cannot

run your product or your computer system properly later, please go to the Microtek Download Service

site at ww7.microtek.com.tw/service.php to download and install any updates you may require.

For additional information about Microtek products, please visit our website at

www.microtek.com.

trademarks of their respective companies: Microtek, ArtixScan, ScanWizard of Microtek

International, Inc.; DIGITAL ICE of Kodak. All other trademarks or registered trademarks are

the property of their respective holders. Specifications, software and hardware bundles are

subject to change without notice. Delivery of technical support services subject to change

without notice. Not responsible for typographical errors.

Microtek ScanMaker i800 Plus User manual

Microtek ScanMaker i800 Plus User manual

Microtek ScanMaker i800 Plus User manual

Related papers

Other documents