GE Appliances GFD55ESSNWW Installation guide

Brand: GE Appliances

Model: GFD55ESSNWW

Type: Installation guide

- Fire Hazard

WARNING

• Clothes dryer installation must be performed by a

qualified installer.

• Install the clothes dryer according to these instructions

and local codes.

• DO NOT install a clothes dryer with flexible plastic venting

materials. If flexible metal (semi-rigid or foil-type) duct is

installed, it must be UL-listed and installed in accordance

with the instructions found in “Connecting the Dryer

to House Vent” later in this manual. Flexible venting

materials are known to collapse, be easily crushed and

trap lint. These conditions will obstruct dryer airflow and

increase the risk of fire.

• DO NOT install or store this appliance in any location

where it could be exposed to water or weather.

• To reduce the risk of severe injury or death, follow all

installation instructions.

• Save these instructions. (Installers: Be sure to leave

these instructions with the customer.)

In the Commonwealth of Massachusetts,

the following installation instructions apply:

• Installation must be performed by a qualified or

licensed contractor, plumber, or gasfitter qualified

or licensed by the State.

• If using a ball valve, it shall be a T-handle type.

• A flexible gas connector, when used, must not

exceed 4 feet.

FOR GAS DRYERS ONLY

Dryers

Installation

Instructions

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT – Save these instructions for local electrical

inspector’s use.

IMPORTANT –

Observe all governing codes and

ordinances.

• Install the clothes dryer according to the manufacturer’s

instructions and local codes.

• Note to Installer – Be sure to leave these instructions

with the Consumer.

• Note to Consumer – Keep these instructions for future

reference.

• Clothes dryer installation must be performed by a qualified

installer.

• This dryer must be exhausted to the outdoors.

• Before the old dryer is removed from service or discarded,

remove the dryer door.

• Do not allow children on or in the appliance. Close

supervision of children is necessary when the appliance

is used near children.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

• Install the dryer where the temperature is above 50°F for

satisfactory operation of the dryer control system.

• Remove and discard existing plastic or metal foil duct

and replace with UL-listed duct.

• Service information and the wiring diagram are located

in the control console.

31-16769-5 08-18 GEA

234D2274P004

See your Owner’s Manual for details on how to contact us regarding installation questions

Installation Instructions

Tilt the dryer sideways and remove the foam

shipping pads by pulling at the sides and breaking

them away from the dryer legs. Be sure to remove

all of the foam pieces around the legs.

Remove the bag containing the literature.

UNPACKING YOUR DRYER

ROUGH-IN DIMENSIONS

With Pedestal: 52 3/8” (133 cm)

Stacked: 84” (213.36 cm) - 7.5 cu. ft. models

79 5/8” (202.25 cm) - 7.0 cu. ft. models

NOTE: Dryer height can be adjusted to match washer height.

GE Appliances strongly recommends the use of factory

specified parts. These hoses are manufactured and tested

to meet GE Appliances specifications.

GE Appliances strongly recommends the use of new water

supply hoses. Hoses degrade over time and need to be

replaced every 5

years to reduce the risk of hose failures

and water damage.

Parts and Accessories

Order on-line at GEApplianceparts.com, 24 hours a day

or by phone at 877.959.8688 during normal business hours.

STEAM WATER HOSES (for steam dryer models only):

ACCESSORIES:

Order on-line at GEApplianceparts.com, 24 hours a day or

by phone at 877.959.8688 during normal business hours.

Part Number Accessory

SBSD137HWW

27” width White Pedestal

SBSC137HDG

27” width Diamond Gray Pedestal

GEFLSTACK Stacking Kit for Dryer over Washer

PM08X10085

Flexible Metal Dryer Transition Duct

WE01X20677

Clothes Dryer Shoe Rack

Part Number Accessory

WE25X20060

Complete Kit (hoses, Y-adapter, washers)

WE49X25794

Kit (Short hose, Y-adapter, washers)

and

WE1M847 Long Hose

OR SEPARATELY

WE1M847 Long Hose and

WE1M848 Short Hose

4 3/8”

(11.11 cm)

Side View

39 3/8”

(100 cm)

27”

(68.6 cm)

39 3/8”

(100 cm)

Front View

32 3/16” (81.76 cm)

7.0 cu. ft.

models

33” (83.80 cm)

7.5 cu. ft.

models

4 1/2” (11.43 cm)

7.0 cu. ft.

models

5 3/8” (13.65 cm)

7.5 cu. ft.

models

Installation Instructions

MOBILE OR MANUFACTURED

HOME INSTALLATION

• Installation MUST conform to the MANUFACTURED

HOME CONSTRUCTION AND SAFETY

STANDARD, TITLE 24, PART 3280 or STANDARD

FOR MOBILE HOMES CAN/CSA-Z240 MH, or,

when such standards are not applicable, with

AMERICAN NATIONAL STANDARD FOR MOBILE

HOME, ANSI/NFPA NO. 501B.

• The dryer MUST be vented to the outdoors.

• The exhaust vent MUST be securely fastened to a

non-combustible portion of the mobile home.

• The vent MUST NOT be terminated beneath a

mobile or manufactured home.

• The vent duct material MUST BE METAL.

• KIT 14-D346-33 MUST be used to attach the dryer

securely to the structure.

• The vent MUST NOT be connected to any other

duct, vent or chimney.

• DO NOT use sheet metal screws or other

fastening devices which extend into the interior of

the exhaust vent.

• Provide an opening with a free area of at least 25

square inches for introduction of outside air into

the dryer room.

• See the sections for electrical connection information.

REQUIREMENTS FOR ALCOVE OR

CLOSET INSTALLATION

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18” (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

• The dryer MUST be vented to the outdoors.

• Minimum clearance between dryer cabinet and

adjacent walls or other surfaces is:

0” either side

1” rear

1” front

1” top

• Consideration must be given to provide adequate

clearance for installation and service.

• Closet doors must be louvered or otherwise ventilated

and have at least 60 square inches of open area. If

the closet contains both a washer and a dryer, doors

must contain a minimum of 120 square inches of

open area.

NOTE: WHEN THE EXHAUST DUCT IS LOCATED AT

THE REAR OF THE DRYER, THE CONFIGURATION

OF THE DUCTING MAY REQUIRE GREATER THAN

1” OF REAR CLEARANCE.

Gas Dryers Only:

• No other fuel burning appliance shall be installed in

the same closet as a gas dryer.

• The dryer must be disconnected from the gas

supply piping during pressure testing at pressures

greater than ½ psi (3.5 kPa).

• A 1/8 inch NPT minimum plugged tapping,

accessible for test gauge connection, must be

installed immediately upstream of the gas supply

connection to the dryer.

- Explosion Hazard

WARNING

MINIMUM CLEARANCE OTHER THAN

ALCOVE OR CLOSET INSTALLATION

Minimum clearance to combustible surfaces and

for air opening are: 0” both sides, 1” rear and 1” top.

Consideration must be given to provide adequate

clearance for installation and service.

Installation Instructions

CONNECTING INLET HOSES (for steam dryer models only)

CONNECTING INLET HOSES (cont.)

7. Using pliers, tighten all the couplings with an

additional two–thirds turn.

NOTE: Do not overtighten. Damage to the

couplings may result.

8. Turn the water faucet on.

9. Check for leaks around the ‘’Y’’ connector,

faucet and hose couplings.

WATER SUPPLY REQUIREMENTS

Hot and cold water faucets MUST be installed

within 42 in. (107 cm) of your washer’s water

inlet. The faucets MUST be 3/4 in. (1.9 cm)

garden hose-type so inlet hoses can be

connected. Water pressure MUST be between

10 and 120 pounds per square inch. Your

water department can advise you of your water

pressure.

NOTE: A water softener is recommended

to reduce buildup of scale inside the steam

generator if the home water supply is very hard.

To produce steam, the dryer must connect to

the cold water supply. Since the washer must

also connect to the cold water, a “Y” connector

is inserted to allow both inlet hoses to make that

connection at the same time.

NOTE: Use new inlet hoses; never use old

hoses.

1. Turn the cold water faucet off. Remove the

washer inlet hose from the washer fill valve

connector (cold).

2. Ensure the rubber flat washer is in place and

attach one female coupling of the short hose

provided onto the washer fill valve connector.

Tighten by hand until firmly seated.

3. Attach one male end of the “Y” connector to

the other female coupling of the short hose.

Ensure the rubber flat washer is in place.

Tighten by hand until firmly seated.

4. Insert the filter screen in the coupling of the

washer’s inlet hose. If a rubber flat washer is

already in place remove it before installing the

filter screen. Attach this coupling to one male

end of the ‘’Y’’ connector. Tighten by hand until

firmly seated.

5. Ensure the rubber flat washer is in place and

attach a 4 ft. to 6 ft. long water inlet hose (may

need to be purchased separately) to one male

end of the ‘’Y’’ connector. Tighten by hand until

firmly seated.

6. Ensure the rubber flat washer is in place and

attach the other end of the dryer’s long inlet

hose to the fill valve connector at the bottom

of the dryer back panel. Tighten by hand until

firmly seated.

CONNECTING INLET HOSES

Installation Instructions

CONNECTING A GAS DRYER (skip for electric dryers)

• Before beginning the installation, turn off the circuit

breaker(s) or remove the dryer’s circuit fuse(s) at

the electrical box. Be sure the dryer

cord is unplugged from the wall.

• Turn the dryer’s gas shut-off valve in the supply line

to the OFF position.

• Disconnect and discard old flexible gas connector

and ducting material.

Shut-off

Valve

MATERIALS YOU WILL NEED

4” dia. metal elbow

Pipe compound or

PTFE tape

Flexible gas line

connector

Duct clamps (2) or

Spring clamps (2)

Safety glasses

4” dia. metal duct

(recommended)

Gloves

Soap solution for

leak detection

Exhaust hood

Duct tape

Gas pipe adapters (2),

elbow and pipe plug

TOOLS YOU WILL NEED

10” Adjustable

wrenches (2)

8” Pipe wrench

Flat-blade

screwdriver

Level

Slip-joint pliers

4” dia., UL-listed

flexible metal duct

(if needed)

4” Cover Plate

(Kit WE49X22606)

(if needed)

Installation Instructions

GAS REQUIREMENTS

DRYER GAS SUPPLY CONNECTION

GAS SUPPLY

• A 1/8” National Pipe Taper thread plugged

tapping, accessible for test gauge connection,

must be installed immediately upstream of the

gas supply connection to the dryer. Contact your

local gas utility should you have questions on the

installation of the plugged tapping.

• Supply line is to be 1/2” rigid pipe and equipped

with an accessible shutoff within 6 feet of, and in

the same room with, the dryer.

• Use pipe thread compound appropriate for

natural or LP gas or use PTFE tape.

• Connect flexible metal connector to dryer and

gas supply.

ADJUSTING FOR ELEVATION

• Gas clothes dryers input ratings are based on

sea level operation and need not be adjusted

for operation at or below 2000 ft. elevation. For

operation at elevations above 2000 ft., input

ratings should be reduced at a rate of 4 percent

for each 1000 ft. above sea level.

• Installation must conform to local codes and

ordinances or, in their absence, the NATIONAL

FUEL GAS CODE, ANSI Z223.

You must use with this dryer a flexible metal connector

(listed connector ANSI Z21.24 / CSA 6.10). The length

of the connect shall not exceed 4 ft.

• Use a new CSA International approved flexible

gas supply line. Never reuse old flexible

connectors.

• Install an individual manual shut-off valve

within 6ft. of the dryer in accordance with the

National Fuel Gas Code, ANSI Z223.1/NFPA

54.

• Securely tighten all gas connections.

• If connected to LP gas, have a qualified

person make sure gas pressure DOES NOT

exceed 13” water column.

• Examples of a qualified person include:

licensed heating personnel, authorized gas

company personnel, and authorized service

personnel.

• Failure to do so can result in death,

explosion, or fire.

• The installation must conform with local

codes, or in the absence of local codes, with

the National Fuel Gas Code, ANSI Z223.1/

NFPA 54, or the Natural Gas and Propane

Installation Code, CSA B149.1.

FOR USE WITH NATURAL GAS ONLY

Dryer as produced by manufacturer is to be used

only with a natural gas supply. A manufacturer-

supplied conversion kit is required to convert this

dryer for propane gas supply. Use propane

gas

conversion kit WE25X217

. Conversion must be

made by properly trained and qualified personnel

in accordance with local codes and ordinances.

- Fire Hazard

WARNING

- Explosion Hazard

WARNING

CONNECTING A GAS DRYER (cont.)

2-5/8"

3/8" NPT MALE THREAD GAS SUPPLY

NOTE: Add to vertical dimension

the distance between cabinet

bottom to ﬂoor.

Installation Instructions

CONNECTING A GAS DRYER (cont.)

Install a 1/8” NPT plugged tapping to the

dryer gas line shut-off valve for checking gas

inlet pressure.

Install a flare union adapter to the plugged

tapping.

NOTE: Apply pipe compound or PTFE tape

to the threads of the adapter and plugged

tapping.

Attach the flexible metal gas line connector to

the adapter.

Tighten the flexible gas line connection, using

two adjustable wrenches.

Tighten all connections, using two adjustable

wrenches. Do not overtighten.

CONNECTING THE DRYER TO

THE GAS SUPPLY (cont.)

Open the gas shut-off valve.

Apply pipe compound

or PTFE tape to all

male threads.

Shut-Off

Valve

Plugged

Tapping

CONNECTING THE DRYER TO

THE GAS SUPPLY

Install a female 3/8” NPT elbow at the end of

the dryer gas inlet.

Install a 3/8” flare union adapter to the female

elbow.

IMPORTANT: Use a pipe wrench to securely

hold on to the end of the dryer gas inlet to

prevent twisting the inlet.

NOTE: Apply pipe compound or PTFE tape to

the threads of the adapter and dryer gas inlet.

Apply pipe compound to the

adapter and dryer gas inlet.

Tighten the flexible

gas line using two

adjustable wrenches.

Elbow

Adapter

Items not supplied

Adapter

1/8” NPT

Pipe Plug for

Checking Gas

Inlet Pressure

Shut-Off Valve

Pipe size at

least 1/2”

3/8” NPT

New Metal

Flexible Gas

Line Connector

Installation Instructions

TEST FOR LEAKS

Never use an open flame to test for gas leaks.

Check all connections for leaks with soapy solution or

equivalent.

Apply a soap solution. The leak test solution must not

contain ammonia, which could cause damage to the

brass fittings.

If leaks are found, close the valve, retighten the joint

and repeat the soap test.

ELECTRICAL CONNECTION

INFORMATION FOR GAS DRYERS

(cont.)

ELECTRICAL CONNECTION

INFORMATION FOR GAS DRYERS

Plug into a grounded 3 prong outlet.

DO NOT remove ground prong.

DO NOT use an adapter.

DO NOT use an extension cord.

Failure to do so can result in death, fire or

electrical shock.

• Circuit – Individual properly polarized and grounded

15 or 20 amp circuit breaker or time-delay fuse.

• Power Supply – 2-wire plus ground, 120 Volt, single

phase, 60 Hz, alternating current.

• Outlet Receptacle – Properly grounded 3-prong

receptacle to be located

so the power cord is

accessible when the dryer

is in an installed position.

If a 2-prong receptacle is

present, it is the owner’s

responsibility to have a

licensed electrician replace

it with a properly grounded 3-prong grounding type

receptacle.

GROUNDING INSTRUCTIONS

This dryer must be grounded. In the event of a

malfunction or breakdown, grounding will reduce

the risk of electric shock by providing a path of

least resistance for electric current. This dryer

uses a cord having an equipment-grounding

conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is

properly installed and grounded in accordance

with all local codes and ordinances.

Improper connection of the

equipment-grounding conductor

can result in a risk of electric shock. Check with a

qualified electrician, or service representative or

personnel, if you are in doubt as to whether the

appliance is properly grounded. DO NOT modify

the plug on the power supply cord. If it will not

fit the outlet, have a proper outlet installed by a

qualified electrician.

SAVE THESE INSTRUCTIONS

• Dryer must be electrically grounded in accordance

with local codes and ordinances, or in the absence

of local codes, with the latest edition of the

NATIONAL ELECTRICAL CODE, ANSI/NFPA

NO. 70 or CANADIAN ELECTRICAL CODE, CSA

C22.1. Check with a licensed electrician if you are

not sure that the dryer is properly grounded.

Open Gas

Valve

- Electrical Shock Hazard

WARNING

Ensure proper

ground exists

before use.

• If required by local codes, an external 18 gauge or

larger copper ground wire (not provided) may be

added. Attach to dryer cabinet with a #8-18 x ½”

sheet metal screw (available at any hardware store)

to rear of dryer as illustrated.

Ground

Screw

CONNECTING A GAS DRYER (cont.)

Installation Instructions

CONNECTING AN ELECTRIC DRYER

(Skip for gas dryers and if your dryer already has a power cord attached)

Before making the electrical connection, turn off

the circuit breaker(s) or remove the dryer’s circuit

fuse(s) at the electrical box. Be sure the dryer

cord is unplugged from the wall.

NEVER LEAVE

THE ACCESS COVER OFF THE TERMINAL

BLOCK.

MATERIALS YOU WILL NEED

4” dia. metal elbow

3/4” Strain relief

(UL recognized)

4” Duct clamps (2) or

4” spring clamps (2)

Safety glasses

4” dia. metal duct

(recommended)

Gloves

Exhaust hood

Duct tape

TOOLS YOU WILL NEED

Slip-joint pliers

Level

4” dia., UL-listed

flexible metal duct

(if needed)

Dryer power cord kit

(not provided with

dryer)

UL rated 120/240V,

30A with 3 or 4 prongs.

Identify the plug type

as per the house

receptacle before

purchasing line cord.

Flat-blade

screwdriver

Phillips

screwdriver

4” Cover Plate

(Kit WE49X22606)

(if needed)

POWER CORDS

GE Appliances strongly recommends the use of

factory specified parts. Select the power cord to fit your

installation requirements.

Order on-line at GEApplianceparts.com, 24 hours

a day or by phone at 877.959.8688 during normal

business hours.

Part Number Type Length Amperage

WX9X2 3-Prong 4 Feet 30

WX9X3 3-Prong 5 Feet 30

WX9X4 3-Prong 6 Feet 30

WX9X18 4-Prong 4 Feet 30

WX9X19 4-Prong 5 Feet 30

WX9X20 4-Prong 6 Feet 30

Installation Instructions

ELECTRICAL CONNECTION

INFORMATION FOR ELECTRIC

DRYERS

Use a new UL-listed 240V 30 amp dryer power

supply cord with closed ring terminals or spade

terminals with upturned ends.

Use a UL-listed strain relief.

Disconnect power before making electrical

connections.

Connect neutral wire (white or center wire) to center

terminal.

Ground wire (green or bare wire) must be connected

to green ground connector.

Connect remaining two supply wires to remaining

two terminals.

Securely tighten all electrical connections.

Replace the terminal block cover.

Failure to do so can result in death, fire or electrical

shock.

For electrical connections using a

power cord:

ELECTRICAL CONNECTION

INFORMATION FOR ELECTRIC

DRYERS

For direct wire connections:

Use 10 gauge solid copper wire.

Use a UL-listed strain relief.

Disconnect power before making electrical

connections.

Connect neutral wire (white or center wire) to center

terminal.

Ground wire (green or bare wire) must be connected

to green ground connector.

Connect remaining two supply wires to remaining

two terminals.

Securely tighten all electrical connections.

Replace the terminal block cover.

Failure to do so can result in death, fire or electrical

shock.

GROUNDING INSTRUCTIONS

For a grounded, cord-connected dryer: This

dryer must be grounded. In the event of a

malfunction or breakdown, grounding will

reduce the risk of electric shock by providing

a path of least resistance for electric current.

This dryer uses a cord having an equipment-

grounding conductor and a grounding plug.

The plug must be plugged into an appropriate

outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Improper connection of the

equipment-grounding conductor

can result in a risk of electric shock. Check with a

qualified electrician, or service representative or

personnel, if you are in doubt as to whether the

appliance is properly grounded. DO NOT modify

the plug on the power supply cord. If it will not

fit the outlet, have a proper outlet installed by a

qualified electrician.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

For a permanently connected dryer: This

dryer must be connected to a grounded metal,

permanent wiring system, or an equipment-

grounding conductor must be run with the circuit

conductors and connected to the equipment-

grounding terminal on the appliance.

Improper connection of the

equipment-grounding conductor

can result in a risk of electric shock. Check with a

qualified electrician, or service representative or

personnel, if you are in doubt as to whether the

appliance is properly grounded.

SAVE THESE INSTRUCTIONS

- Fire Hazard

WARNING

- Fire Hazard

WARNING

CONNECTING AN ELECTRIC DRYER

Installation Instructions

CONNECTING DRYER USING

3-WIRE CONNECTION

CONNECTING AN ELECTRIC DRYER

3-wire Connection

NOT for use in Canada.

DO NOT use for Mobile Home Installations.

NOT for use on new construction.

NOT for use on recreational vehicles.

NOT for use in areas where local codes prohibit

grounding through the neutral conduction.

CONNECTING DRYER USING 4-WIRE

CONNECTION (MUST BE USED FOR

MOBILE HOME INSTALLATION)

NOTE: Since January 1, 1996, the National Electrical

Code requires that new constructions use a 4-wire

connection to an electric dryer. A 4-wire cord must also

be used where local codes do not permit grounding

through the neutral.

3-wire connection is NOT for use on new construction.

1. Turn off the circuit breaker(s) (30 amp) or remove

the dryer’s circuit fuse at the electrical box.

2. Be sure the dryer cord is unplugged from the wall

receptacle.

3. Remove the power cord cover located at the lower

back.

4. Remove and discard ground strap. Keep the green

ground screw for Step 7.

5. Install 3/4 in. UL-recognized strain relief to power

cord entry hole. Bring power cord through strain

relief.

6. Connect power cord as follows:

A. Connect the 2 hot lines to the outer screws of the

terminal block (marked L1 and L2).

B. Connect the neutral (white) line to the center of

the terminal block (marked N).

7. Attach ground wire of power cord with the green

ground screw (hole above strain relief bracket).

Tighten all terminal block screws (3) securely.

8. Properly secure power cord to strain relief.

9. Reinstall the cover.

NEVER LEAVE THE COVER OFF OF THE

TERMINAL BLOCK.

NEVER LEAVE THE COVER OFF OF THE

TERMINAL BLOCK.

RELOCATE GREEN

GROUND SCREW

HERE

STRAIN

RELIEF

BRACKET

GREEN OR

YELLOW WIRE

3/4", UL

RECOGNIZED

STRAIN RELIEF

HOT

WIRE

SCREWS

(3)

HOT WIRE

COVER

NEUTRAL

(White)

REMOVE GROUND

STRAP AND DISCARD.

KEEP GREEN

GROUND

SCREW

4 #10 AWG MINIMUM COPPER

CONDUCTORS OR 120/240V 30A POWER

SUPPLY CORD KIT MARKED FOR USE

WITH DRYERS & PROVIDED WITH

CLOSED LOOP OR SPADE TERMINALS

WITH UPTURNED ENDS (NOT SUPPLIED).

STRAIN RELIEF

BRACKET

3/4", UL

RECOGNIZED

STRAIN RELIEF

HOT

WIRE

HOT

WIRE

GROUND

STRAP

GREEN

GROUND

SCREW

NEUTRAL

(White)

SCREWS

(3)

COVER

3 #10 AWG MINIMUM COPPER

CONDUCTORS OR 120/240V 30A POWER

SUPPLY CORD KIT MARKED FOR USE

WITH DRYERS & PROVIDED WITH

CLOSED LOOP OR SPADE TERMINALS

WITH UPTURNED ENDS (NOT SUPPLIED).

1. Turn off the circuit breaker(s) (30 amp) or remove

the dryer’s circuit fuse at the electrical box.

2. Be sure the dryer cord is unplugged from the wall

receptacle.

3. Remove the power cord cover located at the lower

back.

4. Install 3/4-in. UL-recognized strain relief to power

cord entry hole. Bring power cord through strain

relief.

5. Connect power cord as follows:

A. Connect the 2 hot lines to the outer screws of the

terminal block (marked L1 and L2).

B. Connect the neutral (white) line to the center of

the terminal block (marked N).

6. Be sure ground strap is connected to neutral

(center) terminal of block and to green ground

screw on cabinet rear. Tighten all terminal block

screws (3) securely.

7. Properly secure power cord to strain relief.

8. Reinstall the cover.

If required, by local code, install external ground

(not provided) to grounded metal, cold water

pipe, or other established ground determined by

a qualified electrician.

Installation Instructions

EXHAUSTING THE DRYER

TOOLS AND MATERIALS YOU WILL

NEED TO INSTALL EXHAUST DUCT

CONNECTING THE DRYER TO

HOUSE VENT

RIGID METAL TRANSITION DUCT

• For best drying performance, a rigid metal transition

duct is recommended.

• Rigid metal transition ducts reduce the risk of

crushing and kinking.

UL-LISTED FLEXIBLE METAL CLOTHES

DRYER TRANSITION DUCT

• If rigid metal cannot be used, then UL-listed flexible

metal clothes dryer transition duct (GE Appliances

part – PM08X10085) can be used.

• Never install transition duct in walls, ceilings, floors

or other enclosed spaces.

• Total length of transition duct should not exceed 8’

(2.4 m).

• For many applications, installing elbows at both

the dryer and the wall is highly recommended (see

illustrations in next section). Elbows allow the dryer

to sit close to the wall without kinking and/or crushing

the transition duct, maximizing drying performance.

• Avoid resting the duct on sharp objects.

UL-LISTED FLEXIBLE METAL (FOIL-TYPE)

TRANSITION DUCT

• In special installations, it may be necessary to

connect the dryer to the home exhaust vent

using flexible metal (foil-type) transition duct. UL–

LISTED universal flexible dryer transition duct

(GE Appliances parts – PM8X73 or WX8X73)

may be used ONLY in installations where rigid

metal or flexible metal transition ducting cannot be

used AND where a 4” diameter can be maintained

throughout the entire length of the transition duct.

• In Canada and the United States, only transition

ducts that comply with “UL 2158A STANDARD

FOR CLOTHES DRYER TRANSITION DUCT”

shall be used.

• Avoid resting the duct on sharp objects.

• For best drying performance:

1. Slide one end of the duct over the clothes

dryer outlet pipe.

2. Secure the duct with a clamp.

3. With the dryer in its permanent position,

extend the duct to its full length. Allow 2”

of duct to overlap the exhaust pipe. Cut off

and remove excess duct. Keep the duct as

straight as possible for maximum airflow.

4. Secure the duct to the exhaust pipe with the

other clamp.

Phillips-head

screwdriver

Duct tape or

duct clamp

Rigid or UL-listed flexible

metal 4” (10.2 cm) duct

Drill with 1/8” drill bit

(for bottom venting)

Hacksaw

Vent hood

This dryer MUST be vented to the outdoors.

Use only 4” rigid metal ducting for the home

exhaust duct.

Use only 4” rigid metal or UL-listed dryer

transition duct to connect the dryer to the

home exhaust.

DO NOT use a plastic vent.

DO NOT exhaust into a chimney, kitchen

exhaust, gas vent, wall, ceiling, attic, crawl

space, or concealed space of a building.

DO NOT install a screen in or over the exhaust

duct.

DO NOT install a booster fan in the exhaust

duct.

DO NOT use duct longer than specified in the

exhaust length table.

Failure to follow these instructions can result in

death or fire.

PARTS AVAILABLE FROM

GEAPPLIANCEPARTS.COM OR

LOCAL SERVICE ORGANIZATIONS

PM8X85

Outdoor exhaust hood

PM08X10085

8’ Flexible metal clothes dryer transition

duct with 2 clamps

WX08X10130

4” Dryer exhaust clamp

WE49X22606

Rear exhaust opening cover, for side or

bottom vented dryers

- Fire Hazard

WARNING

Installation Instructions

EXHAUSTING THE DRYER (cont.)

Using exhaust longer than specified length will:

• Increase the drying times and the energy cost.

• Reduce the dryer life.

• Accumulate lint, creating a potential fire hazard.

The correct exhaust installation is YOUR

RESPONSIBILITY.

Problems due to incorrect installation are not

covered by the warranty.

The MAXIMUM ALLOWABLE length of the exhaust

system depends upon the type of duct, number of turns,

the type of exhaust hood (wall cap) and all conditions

noted on the chart.

• Internal elbows added for side or bottom vent

conversions must be included in the total elbow count.

• Any elbow greater than 45° should be treated as a 90°

elbow; one elbow of 45° or less may be ignored.

• Two 45° elbows will be treated like one 90° elbow.

• For the side exhaust installations, add one 90° elbow to

the chart.

• For every additional 90° elbow, reduce the allowable

vent system length by 10 feet.

• When calculating the total vent system length, you

must add all the straight portions and elbows of the

system (including the transition duct).

EXHAUST LENGTH

EXHAUST

LENGTH

FOR

NORMAL

VENT

MODELS

RECOMMENDED MAXIMUM LENGTH

Exhaust Hood Types

Recommended

Use only for short run

installations

4" DIA.

2-1/2"

No. of 90° Elbows Rigid Metal Rigid Metal

0 90 Feet 60 Feet

1 60 Feet 45 Feet

2 45 Feet 35 Feet

3 35 Feet 25 Feet

4 25 Feet 15 Feet

EXHAUST

LENGTH

FOR

LONG

VENT

MODELS

RECOMMENDED MAXIMUM LENGTH

Exhaust Hood Types

Recommended

Use only for short run

installations

4" DIA.

2-1/2"

No. of 90° Elbows Rigid Metal Rigid Metal

0 200 Feet 175 Feet

1 185 Feet 165 Feet

2 175 Feet 155 Feet

3 165 Feet 145 Feet

4 155 Feet 135 Feet

5 145 Feet 125 Feet

• DO NOT bend

or collapse

ducting.

Use elbows

if turns are

necessary.

• DO NOT use

excessive

exhaust

length. Cut

duct as short

as possible.

• DO NOT

crush duct

against

the wall

• DO NOT

set dryer

on duct

• DO cut duct as short

as possible and

install straight into

wall.

•

DO use elbows

when turns are

necessary.

Elbows

Installation Instructions

BEFORE YOU BEGIN

• Remove and discard existing plastic or metal foil

duct and replace with UL-listed duct.

• Remove any lint from the wall exhaust opening.

Internal

Duct

Opening

Wall

Check that exhaust

hood damper

opens and closes

freely.

STANDARD REAR EXHAUST

We recommend that you install your dryer before

installing your washer. This will permit direct

access for easier exhaust connection.

Slide the end of the exhaust duct on the back of the

dryer and secure with duct tape or a hose clamp.

NOTE: We strongly recommend using rigid metal

exhaust duct. However, if flexible ducting is used it

must be UL-Listed metal, not plastic.

• For straight line installation, connect the dryer

exhaust to the external exhaust hood using duct

tape or clamp.

RECOMMENDED CONFIGURATION

TO MINIMIZE EXHAUST BLOCKAGE

Using duct elbows will prevent duct kinking and

collapsing.

EXHAUST SYSTEM CHECKLIST

HOOD OR WALL CAP

• Terminate in a manner to prevent back drafts or entry of

birds or other wildlife.

• Termination should present minimal resistance to

the exhaust airflow and should require little or no

maintenance to prevent clogging.

• Wall caps must be installed at least 12” above ground

level or any other obstruction with the opening pointed

down.

SEPARATION OF TURNS

• For best performance, separate all turns by at least

4 ft. of straight duct, including distance between

last turn and dampened exhaust hood (wall cap).

SEALING OF JOINTS

• All joints should be tight to avoid leaks. The male end

of each section of duct must point away from the dryer.

• Duct joints should be made air- and moisture-tight

by wrapping the overlapped joints with duct tape or

aluminum tape.

• Do not assemble ductwork with any fasteners that

extend into the duct. These fasteners can accumulate

lint, creating a potential fire hazard.

• Horizontal runs should slope down towards the

outdoors 1/4” per foot.

• Provide an access for inspection and cleaning of

the exhaust system, especially at turns and joints.

Exhaust system shall be inspected and cleaned at

least once a year.

INSULATION

• Ductwork that runs through an unheated area or is

near air conditioning should be insulated to reduce

condensation and lint build-up.

Wall Side

Dryer

Side

Duct Tape

EXHAUSTING THE DRYER (cont.)

Duct

Transition

Ducting

Installation Instructions

SIDE OR BOTTOM VENTING

Disconnect dryer from electrical supply.

Wear gloves and arm guards.

Close the back opening with cover plate (Kit

WE49X22606).

Failure to do so may result in fire, electrical

shock or lacerations.

- Fire Hazard

WARNING

SIDE OR BOTTOM VENTING (cont.)

Dryer Exhaust to right of the cabinet for Electric

models only.

Dryer Exhaust to left* of the cabinet for Gas and

Electric models.

Dryer Exhaust to the bottom of cabinet for Gas

and Electric models.

Detach and remove the right (electric models only),

left* or bottom knockout as desired. Remove the

screw inside the dryer exhaust duct and save.

Pull the duct out of the dryer.

Cut the duct as shown and keep portion A.

ADDING A NEW DUCT

Reconnect the cut portion (A) of the duct to the blower

housing. Make sure that the shortened duct is aligned

with the tab in the base. Use the screw saved previously

to secure the duct in place through the tab on the

appliance base.

ADDING ELBOW AND DUCT FOR

EXHAUST TO RIGHT (ELECTRIC

MODELS ONLY) OR LEFT* SIDE OF

CABINET

• Preassemble 4” elbow with 4” duct. Wrap duct tape

around joint.

• Insert duct assembly, elbow first, through the side

opening and connect the elbow to the dryer internal

duct.

Be sure not to pull or damage the electrical

wires inside the dryer when inserting the duct.

TAB LOCATION

Remove

screw

and save

Remove desired

knockout (one only)

Right

(electric

models

only)

Left*

Bottom

Through the rear opening, locate the tab in the middle

of the appliance base. Lift the tab to about 45°,

using

a flat-blade screwdriver.

Portion “A”

Right (electric

models only)

or left* side

exhaust

Fixing hole

Left*

Right

Exhaust can be

added to right

(electric models

only) or left* side

Duct

tape

Right

Left*

* Left side exhaust is not available for Long Vent models.

For 7.0 cu. ft models only, use the dimension below:

Fixing hole

9” (22.86cm)

Bend tab

up 45°

Not for gas models

Left*

EXHAUSTING THE DRYER (cont.)

Fixing hole

»2” (34.29cm)

For 7.5 cu. ft models only, use the dimension below:

Installation Instructions

EXHAUSTING DRYER (cont.)

SIDE OR BOTTOM VENTING (cont.)

ADDING COVER PLATE TO REAR OF

CABINET

ADDING ELBOW AND DUCT FOR

EXHAUST TO LEFT OR RIGHT SIDE OF

CABINET (cont.)

• Apply duct tape as shown

on the joint between the

dryer internal duct and

the elbow, and also the

joint between the elbow

and the side duct.

Use 4” rigid metal ducting

only inside the dryer. Internal duct joints must be

secured with tape, otherwise they may separate

and cause a safety hazard.

DUCT

TAPE

ADDING ELBOW FOR EXHAUST

THROUGH BOTTOM OF CABINET

• Insert the elbow through the rear opening and

connect it to the dryer internal duct.

• Apply duct tape as

shown on the joint

between the dryer

internal duct and the

elbow, and also the

joint between the elbow

and the bottom duct.

Internal duct joints

must be secured with tape; otherwise, they may

separate and cause a safety hazard.

Duct tape

FINAL SETUP

LEVEL THE DRYER

Stand the dryer upright near the final location and

adjust the four leveling legs at the corners to ensure

that the dryer is level from side to side and front to

rear.

Lower

Raise

PLUG DRYER IN

DRYER START-UP

Press the Power button.

NOTE: If the dryer has been

exposed to temperatures

below freezing for an extended

period of time, allow it to warm up before pressing Power.

Otherwise, the display will not come on.

The dryer is now ready for use.

Ensure proper

ground exists

before use.

Connect standard metal elbows and ducts to complete

the exhaust system. Cover back opening with the plate

(kit WE49X22606) which can be purchased from

GEApplianceparts.com or a local service provider.

Place dryer in final location.

Plate

(Kit WE49X22606)

NEVER LEAVE THE BACK OPENING WITHOUT

THE PLATE.

(appearance will vary)

Disconnect power supply before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical

shock.

WARNING

- Shock Hazard

Certain internal parts are intentionally not grounded

and may present a risk of electric shock only during

servicing.

Service personnel – DO NOT contact the following

parts while the appliance is energized: Power

button, Start/Pause button, electronic board, outlet

thermostat, outlet thermistor or water valve.

- Electrical Shock Hazard

WARNING

• La instalación de la secadora debe efectuarla un

instalador calificado.

• Instale la secadora de ropa de acuerdo con estas

instrucciones y en cumplimiento con los códigos locales.

• NO instale una secadora de ropa con conductos de

plástico flexible. Si se instala un conducto flexible de

metal (semi rígido o de tipo papel de aluminio), debe

estar aprobado por UL e instalarse de acuerdo con

las instrucciones de “Cómo conectar la secadora a la

ventilación doméstica” de este manual. Los materiales

de los conductos flexibles a menudo se desploman,

se aplastan y atrapan pelusas. Estas condiciones

obstruyen la corriente de aire de la secadora e

incrementan el riesgo de incendio.

• NO instale o almacene este aparato en un lugar

donde se vea expuesto al agua o a las inclemencias

del tiempo.

• Para reducir el riesgo de una lesión grave o de muerte,

cumpla con todas las instrucciones de instalación.

• Guarde estas instrucciones. (Instaladores: Asegúrense

de dejar estas instrucciones al consumidor).

En la Mancomunidad de Massachusetts,

se aplican las instrucciones de instalación

siguientes:

• Este producto debe instalarlo un plomero

matriculado o un instalador de gas.

• Cuando use válvulas esféricas de apagado de gas,

deberán ser del tipo de manija en T.

• Si se usa una conexión flexible para gas, ésta no

debe superar 1.22 m (4 pies).

SECADORAS A GAS ÚNICAMENTE

Instrucciones

de Instalación

Secadora

ANTES DE COMENZAR

Lea estas instrucciones por completo y con

detenimiento.

IMPORTANTE –

Guarde estas instrucciones para el

uso de inspectores eléctricos locales.

IMPORTANTE –

Cumpla con todos los códigos y

ordenanzas vigentes.

• Instale la secadora de acuerdo con las instrucciones del

fabricante y los códigos locales.

• Nota al instalador – Asegúrese de dejar estas

instrucciones con el consumidor.

• Nota al usuario – Conserve estas instrucciones para

referencia futura.

• La instalación de la secadora debe efectuarla un

instalador calificado.

• Esta secadora debe tener una salida al exterior.

• Antes de que la secadora antigua sea retirada del

servicio o eliminada, quítele la puerta.

• No permita que niños se suban o se metan dentro del

artefacto. Se requiere una supervisión estricta cuando el

aparato es utilizado cerca de niños.

• El instalador tiene la responsabilidad de efectuar una

instalación adecuada.

• La garantía no cubre las fallas del producto debido a una

instalación incorrecta.

• Instale la secadora en lugares donde la temperatura sea

mayor a 50°F para un funcionamiento satisfactorio del

sistema de control de la secadora.

• Quite y descarte el conducto existente de plástico o de

papel de aluminio y coloque un conducto aprobado por UL.

• La información sobre reparaciones y el diagrama del

cableado se encuentran en la consola de control.

ADVERTENCIA

- Riesgo de incendio

31-16769-5 08-18 GEA

234D2274P004

Consulte su Manual del Propietario para obtener detalles sobre cómo contactarnos con respecto a las

preguntas de instalación

GE Appliances recomienda enfáticamente el uso de

piezas específicas de fábrica. A continuación figura una

lista de mangueras de fábrica que podrá adquirir. Dichas

mangueras son fabricadas y probadas de modo que se

cubran las especificaciones de GE Appliances.

GE Appliances recomienda enfáticamente el uso de

nuevas mangueras de suministro de agua. Con el paso del

tiempo, las

mangueras se degradan y deben ser reemplazadas

cada 5 años, a fin de reducir el riesgo de fallas sobre las

mismas y daños con el agua.

Piezas y Accesorios

Ordene hoy a través de Internet en GEApplianceparts.com,

las 24 horas del día o en forma telefónica llamando al

877.959.8688, durante el horario comercial habitual.

MANGUERA DE VAPOR Y AGUA (sólo para los modelos de secadoras de vapor):

Número de Pieza

Accesorio

WE25X20060 Kit Completo (mangueras,

adaptador en Y, arandelas) o

WE49X25794 Kit (Manguera corta, adaptador en

Y, arandelas) y

WE1M847

Manguera Larga

O POR SEPARADO

WE1M847

Manguera Larga y

WE1M848

Manguera Corta

Instrucciones de instalación

Incline la secadora de costado y saque los soportes de espuma de embalaje tirando de los costados y

quitándolos de las patas de la secadora. Asegúrese de quitar todas las piezas de espuma de las patas.

Saque la bolsa que contiene la información.

CÓMO DESEMPACAR LA SECADORA

DIMENSIONES APROXIMADAS

Con pedestal: 52 3/8” (133 cm)

Apilada: 84” (213.36 cm) - 7,5 pies cú. modelos

79 5/8” (202.25 cm) - 7,0 pies cú. modelos

NOTA: La altura de la secadora puede ser ajustada para quedar a la misma a altura de la lavadora.

4 3/8”

(11,11 cm)

Visión lateral

39 3/8”

(100 cm)

27”

(68,6 cm)

39 3/8”

(100 cm)

Visión frontal

32 3/16” (81,76 cm)

7,0 pies cú.

modelos

33” (83,80 cm)

7,5 pies cú.

modelos

4 1/2” (11,43 cm)

7,0 pies cú.

modelos

5 3/8” (13,65 cm)

7,5 pies cú.

modelos

ACCESORIOS:

Ordene hoy a través de Internet en GEApplianceparts.com,

las 24 horas del día o en forma telefónica llamando al

877.959.8688, durante el horario comercial habitual.

Número de Pieza

Accesorio

SBSD137HWW

Pedestal blanco 27” de ancho

SBSC137HDG

Pedestal gris diamante 27” de

ancho

GEFLSTACK Kit para apilar Secadora sobre

Lavadora

PM08X10085

Ducto de transición de metal flexible

WE01X20677

Estante de secadora para zapatos

Instrucciones de instalación

INSTALACIÓN EN CASAS MÓVILES

O PREFABRICADAS

• Instalación DEBE cumplir con la NORMA SOBRE

CONSTRUCCIÓN Y SEGURIDAD DE CASAS

PREFABRICADAS, TÍTULO 24, PARTE 3280 o

NORMA PARA CASAS RODANTES CAN/CSA-Z240

MH, o, cuando dicha norma no sea aplicable, con

la NORMA NACIONAL ESTADOUNIDENSE PARA

CASAS MÓVILES, ANSI/NFPA Nº 501B.

• La secadora DEBE tener ventilación al exterior.

• La ventilación del escape DEBERÁ estar ajustado de forma

segura a una parte no combustible de la casa rodante.

• La ventilación NO DEBE terminar debajo de una casa

móvil o prefabricada.

• El material del conducto de ventilación DEBE SER METAL.

• DEBE utilizarse el KIT 14-D346-33 para conectar bien la

secadora a la estructura.

• La ventilación NO DEBE conectarse a ningún otro

conducto, ventilación o chimenea.

• NO utilice tornillos para placas de metal u otros

dispositivos de sujeción que se extiendan al interior

de la ventilación de salida.

• Debe contar con una abertura con un espacio libre de

por lo menos 25 pulgadas cuadradas para el ingreso

de aire exterior dentro de la secadora habitación.

• Para acceder a información sobre la conexión eléctrica,

consulte la section.

REQUERIMIENTOS - INSTALACIÓN

EN NICHOS O ARMARIOS

Mantenga cualquier material y vapores inflamables,

tales como gasolina, alejados de la secadora.

Coloque la secadora a por lo menos 18” (46 cm.)

del piso cuando sea instalada en un garaje.

Si no se cumple con esto, se podrá producir una

explosión, incendio o la muerte.

• Esta secadora DEBE tener una ventilación al exterior.

• El espacio libre mínimo entre el armario de la secadora y

las paredes adyacentes u otras superficies es:

0” sobre ambos lados

1” la parte trasera

1” sobre el frente

1” superior

• Se deberá considerar que se debe brindar el despeje

adecuado para la instalación y el servicio técnico.

•

Las puertas del armario deben contar con rejillas u otro

tipo de ventilación y tener por lo menos 60 pulgadas

cuadradas de espacio abierto. Si el armario incluye una

lavadora y una secadora, las puertas deben contener

un mínimo de 120 pulgadas cuadradas de espacio

abierto.

NOTA: CUANDO EL CONDUCTO DE SALIDA ESTÁ

UBICADO EN LA PARTE TRASERA DE LA SECADORA,

LA CONFIGURACIÓN DEL DUCTO PODRIA REQUERIR

DETRÁS UN CLARO MAYOR A 1 PULGADA.

Secadoras a Gas Únicamente:

• No se deberá instalar ningún otro electrodoméstico que

consuma combustible en el mismo armario donde haya

una secadora a gas.

•

La secadora se deberá desconectar de la tubería de

suministro de gas durante la prueba de presión en

presiones superiores a ½ psi (3.5 kPa).

•

Una rosca cubierta NPT de 1/8”, accesible para la

conexión de un dispositivo de calibración, deberá ser

instalada inmediatamente arriba de la conexión del

suministro de gas a la secadora.

- Riesgo de

explosión

ADVERTENCIA

ESPACIO LIBRE MÍNIMO EN

OTROS ESPACIOS QUE NO SEAN

INSTALACIONES EN NICHOS O

ARMARIOS

Los espacios libres mínimos respecto de superficies

combustibles y de aberturas de aire son: 0” a ambos

lados, 1” en la parte trasera y 1” superior. Debe

tenerse en cuenta un espacio libre adecuado para un

funcionamiento y reparación correctos.

Instrucciones de instalación

CÓMO CONECTAR MANGUERAS DE ENTRADA

(sólo para los modelos de secadoras de vapor)

CÓMO CONECTAR MANGUERAS

DE ENTRADA

Para producir vapor, la secadora debe

conectarse al suministro de agua fría. Ya que

la lavadora también debe conectarse al agua

fría, debe introducirse un conector en “Y” para

permitir que ambas mangueras de entrada

puedan utilizarse al mismo tiempo.

NOTA: Utilice nuevas mangueras de entrada;

nunca utilice mangueras viejas.

1. Cierre el grifo de agua fría. Quite la manguera

de entrada de la lavadora del conector de la

válvula de llenado (fría).

2. Asegúrese de que la arandela plana de

goma se encuentre en su lugar y sujete una

unión hembra de la manguera corta provistas

en el conector de la válvula de llenado de

la lavadora. Ajuste a mano hasta que esté

firmemente asentada.

3. Sujete un extremo macho del conector en

“Y” a la unión hembra de la manguera corta.

Asegúrese de que la arandela plana de goma

se encuentre en su lugar. Ajuste a mano hasta

que esté firmemente asentada.

4. Introduzca el filtro en la unión de la manguera

de entrada de la lavadora. Si la arandela plana

de goma ya se encuentra en su lugar, quítela

antes de instalar el filtro. Sujete esta unión a un

extremo macho del conector en “Y”. Ajuste a

mano hasta que esté firmemente asentada.

5. Asegúrese de que la arandela de goma plana

se encuentra en su posición y coloque una

manguera de entrada de agua de 4 a 6 pies

de largo (puede ser necesario comprarla por

separado) a un extremo macho del conector

‘’Y‘’. Apriete con la mano hasta que quede

firmemente asentado.

6. Asegúrese de que la arandela plana de goma se

encuentre en su lugar y sujete el otro extremo

de la manguera larga de entrada al conector

de la válvula de llenado en la parte inferior del

panel trasero de la secadora. Ajuste a mano

hasta que esté firmemente asentada.

CÓMO CONECTAR MANGUERAS

DE ENTRADA (cont.)

7. Utilizando alicates, ajuste todas las uniones

con un giro adicional de dos tercios.

NOTA: No ajuste de más. Pueden dañarse las

uniones.

8. Abra el grifo de agua.

9. Controle la presencia de pérdidas alrededor

del conector en “Y”, el grifo y las uniones de

las mangueras.

REQUISITOS DE SUMINISTRO DE

AGUA

Los grifos de agua caliente y fría DEBEN

instalarse dentro de las 42 pulg. (107 cm) de

la entrada de agua de la lavadora. Los grifos

DEBEN ser del tipo de manguera de jardín

de 3/4 pulg. (1.9 cm) para que las mangueras

de entrada puedan conectarse. La presión de

agua DEBE hallarse entre 10 y 120 libras por

pulgada cuadrada. La compañía de agua puede

informarle sobre la presión de agua.

NOTA: Se recomienda el uso de un suavizante

de agua para reducir la acumulación de sarro

dentro del generador de vapor si el suministro

doméstico contiene agua muy dura.

Page is loading ...

GE Appliances GFD55ESSNWW Installation guide

Brand: GE Appliances

Model: GFD55ESSNWW

Type: Installation guide

Download PDF

report

in other languages

español: GE Appliances GFD55ESSNWW Guía de instalación

GE Appliances GFD55ESSNWW Installation guide

GE Appliances GFD55ESSNWW Installation guide

in other languages

Related papers

Other documents