Lumark WPSLED10 Operating instructions

Brand
Lumark
Model
WPSLED10
Type
Operating instructions

This manual is also suitable for

INS #
Brand Logo
reversed out of
black
INS #
IB514012EN
Installation Instructions - WPSLED
Instructions d’installation - WPSLED
Instrucciones de instalación - WPSLED
IMPORTANT: Read before installing fixture. Retain for future reference.
SAFETY: This fixture must be wired in accordance with the National Electrical Code and applicable local codes and
ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under
installation section.
WARNING
Make certain power is OFF before starting installation
or attempting any maintenance. Risk of fire/electric
shock. If not qualified, consult an electrician.
WARNING
Risk of Electric Shock—Disconnect power at fuse or
circuit breaker before installing or servicing.
WARNING
Risk of Burn—Disconnect power and allow fixture to
cool before servicing.
WARNING
Risk of Personal Injury—Fixture may become damaged
and/or unstable if not installed properly.
WARNING
DO NOT mount luminaire within 6” of a combustible
surface. DO NOT handle luminaire by the glass.
ote:N These instructions do not claim to cover all
details or variations in the equipment, procedure,
or process described, nor to provide directions
for meeting every possible contingency during
installation, operation or maintenance. When
additional information is desired to satisfy a
problem not covered sufficiently for user’s purpose,
please contact your nearest representative.
ote:N Specifications and dimensions subject to change
without notice.
2
EATON IB514012EN Installation instructions
Installation Instructions - WPSLED
INSTALLATION
Applications
These luminaires are designed for outdoor, wet location
services and should not be used in areas with limited
ventilation or in high ambient temperature enclosures. The
luminaire shall be wall mount only. Inverted mounting will
cause overheating and possible water entry.
Tools Required
Philips screwdriver, Torx T-20 bit (included), 6mm multi-bit
screw driver or 6mm socket, 1/4” drill bit.
1. Remove mounting plate from fixture and remove drain
plugs. (Figure 1.)
2. Determine size of recessed box and knock out
corresponding holes on mounting plate.
3. Place back gasket pad between mounting plates and
fixture. Pull wires through center hole of mounting
plate.
4. Use approved connectors to connect fixture leads to
supply leads and make wire splices inside junction box.
5. Install mounting plate with screws over recessed
surface box. Install the provided self-adhesive gasket to
the back of the fixture to cover the mounting plate. Also
be sure to caulk between mounting plate and box to
insure a weather tight seal.
6. Install fixture over threaded nipple and attach lock-nut.
Adjust fixture alignment for horizontal lamp orientation.
ote:N To weatherproof your outdoor installation, all gaskets
must be seated properly and all screws inserted and
tightened firmly. Apply weatherproof silicone sealant
around all edges between the fixture housing and
mounting surface.
ote:N Mounting height to be a minimum of 6 feet.
Visor Installation
Content
1 Visor, 4 Screws, 4 Washers.
1. Line up the visor with glass door of fixture.
2. Use the enclosed screws and washers to mount the
visor according to (Figure 2.)
Figure 1.
Mounting
Plate
Junction
Box
Wire Connector
Diffuser
Figure 2.
3
EATON IB514012EN Installation instructions
Installation Instructions - WPSLED
Figure 3.
Retainer
Wire Guard Installation
Content
1 Wire Guard, 4 Screws, 4 Washers.
1. Open the glass door of fixture, screw-off and save the
retainer.
2. Install the wire guard, use enclosed 4 new “longer”
screws (replace the original 4 screws) and twist the
retainer back, according to (Figure 3.)
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Eaton
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.eaton.com/lighting
Canada Sales
5925 McLaughlin Road
Mississauga, Ontario L5R 1B8
P: 905-501-3000
F: 905-501-3172
© 2016 Eaton
All Rights Reserved
Printed in USA
Imprimé aux États-Unis
Impreso en los EE. UU.
Publication No. IB514012EN
December 6, 2016
Eaton is a registered trademark.
All trademarks are property
of their respective owners.
Eaton est une marque de commerce
déposée. Toutes les autres marques
de commerce sont la propriété de leur
propriétaire respectif.
Eaton es una marca comercial
registrada. Todas las marcas
comerciales son propiedad de sus
respectivos propietarios.
Product availability, specifications,
and compliances are subject to
change without notice
La disponibilité du produit, les
spécifications et les conformités
peuvent être modifiées sans préavis
La disponibilidad de productos, las
especificaciones y los cumplimientos
están sujetos a cambio sin previo aviso
Warranties and Limitation of Liability
Please refer to www.eaton.com/LightingWarrantyTerms for our terms and conditions.
Garanties et limitation de responsabilité
Veuillez consulter le site www.eaton.com/LightingWarrantyTerms pour obtenir les conditions générales.
Garantías y Limitación de Responsabilidad
Visite www.eaton.com/LightingWarrantyTerms para conocer nuestros términos y condiciones.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Lumark WPSLED10 Operating instructions

Brand
Lumark
Model
WPSLED10
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents