ENABLING BRIGHT OUTCOMES
Installation Manual
F40 Pollution Filter
Registered office: Barco NV
President Kennedypark 35, 8500 Kortrijk, Belgium
www.barco.com/en/support
www.barco.com
Barco Fredrikstad AS
Habornveien 53, N-1630 Gamle Fredrikstad, Norway
www.barco.com
1 Filter Installation................................................................................................................................................................................................5
1.1 Kit Content ...............................................................................................................................................................................................6
1.2 Environmental Conditions...............................................................................................................................................................6
1.3 Assembly and installation................................................................................................................................................................6
1.4 Cleaning the filter .................................................................................................................................................................................7
1.5 Removing the filter module.............................................................................................................................................................8
R5911522 /00 F40 Pollution Filter
3
Table of contents
R5911522 /00 F40 Pollution Filter4
R5911522 /00 F40 Pollution Filter6
1.1 Kit Content
Kit Content
Article Number
Description Quantity
R8789294 Pollution Filter Frame 1
R8789341 Pollution filter 1
505–0276 S/D Filter screw Captive 6
1.2 Environmental Conditions
Due to changed airflow resistance when filter is installed, there are changes in the ambient operating
conditions for the projector. See table below.
Environment
Ambient operating temperature Relative humidity
0 – 500m +10 - 40°C 10 –80% RH
500 –1500m +10 - 35°C 10 –80% RH
1500 — 3000m +10 - 30°C 10 –80% RH
1.3 Assembly and installation
Installation procedure
1. Press the captive screws (505–0276) in the corresponding holes in the filter frame, as indicated in the
illustration below. Ensure that they snap into position.
Image 1-1
2. Apply the filter frame over the projector’s side cover. Ensure that the captive screws in the filter frame align
with the holes in the projector side cover, as shown in the illustration.
Filter Installation
R5911522 /00 F40 Pollution Filter 7
Image 1-2: Applying the filter frame Image 1-3: Microswitch versus stud alignment
3. Ensure that the stud on the filter frame engages the micro switch in the front of the side cover.
4. Hold the filter frame in position, and enter the screws in each corner in the corresponding threads in the side
cover. Tighten the screws in a cross pattern. Enter and tighten the two last screws
5. Apply the pollution filter unit in to the filter frame, and ensure that the locking tabs “click” in position and that
the filter unit is in locked position.
Image 1-4: Applying the filter to the frame Image 1-5: Filter frame in position
Image 1-6: Location of lock tabs.
1.4 Cleaning the filter
Remove the filter module (See “Removing the filter module”, page 8), and carefully clean it in a water and
NaCO3 mixture.
Reassemble the filter module after drying.
Filter Installation
Barco Fredrikstad AS | Habornveien 53, N-1630 Gamle Fredrikstad, Norway
Registered office: Barco NV | President Kennedypark 35, 8500 Kortrijk, Belgium
www.barco.com
R5911522 /00 | 2019-04-09
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Barco FL40-4K MKII Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Barco Avielo Helios Owner's manual
-
Barco FS40-4K MKII Installation guide
-
-
Barco CRPN-62B Owner's manual
-
-
Barco Avielo Optix Owner's manual
-
-
-
-