Miller LA000000 Owner's manual

Brand: Miller

Model: LA000000

Type: Owner's manual

This manual is also suitable for

MIG RUNNER CART

OWNER’S MANUAL

OMĆ207 132D October 2002

Mig Runner Cart (195445, 907051, 907061, 907092)

WARNING

ELECTRIC SHOCK can kill.

• Do not touch live electrical parts.

• Turn Off welding power source and input disconnect

device.

• Disconnect input plug or power conductors from

deenergized supply BEFORE moving welding

power source.

CYLINDERS can explode if damaged.

• Keep cylinders away from welding and other

electrical circuits.

• Never touch cylinder with welding electrode.

• Always secure cylinder to running gear, wall, or

other stationary support.

FALLING EQUIPMENT can cause injury

and damage, OVERSIZED CYLINDER

can cause tipping.

• Properly install and secure all equipment onto cart

before using cart.

• Always secure or remove any tools stored on cart

before moving unit.

• Do not lift cart in any manner when equipment and

cylinder(s) are installed – use handles to move cart.

• Do not overload handles with cables – use standard

10 to 15 foot cables as maximum lengths.

• Do not move cart where two wheels are at different

heights and cart could tip – avoid tipping.

• Be careful when moving unit over uneven surfaces.

803 117-A

1 Handles

Remove the two lag bolts that are

holding the handles in place.

Install handles with the rubber grips

pointing downward and outward as

shown using supplied 3/8–16 nuts

and bolts.

2 Cylinder Chain

Install the center clip of the cylinder

chain to the center hole of the bottle

mounting bracket as shown.

. The bottle mounting bracket

can be moved to the middle

shelf to accommodate two

small bottles or one small and

one large bottle.

3 Lag Bolts

Remove the remaining lag bolts

from the skid, slide the cart forward,

remove front skid support. Roll cart

off skid.

. The power source may or may

not be already mounted in the

Mig Runner Cart

Tools Needed:

5/16, 9/16 in

9/16 in

Figure 1. Installing Running Gear/Cylinder Rack

OM-207 132 Page 2

803 115-A / 803 116–B

. For hooking up the power

source, the wire feeder,

welding guns, accessories

etc., see the Owner’s Manu-

al for the individual unit.

1 Power Source

Mount the power source to the

cart as shown using the 4 sup-

plied 1/4–20 screws.

. The power source may or may

not be already mounted in the

Mig Runner Cart

2 Wire Feeders

3 Stand Off Supports

Install the stand off supports to the

top of the cart (use 3 stand off sup-

ports for the 22A feeder, use 4

stand off supports for the S–74D

feeder) as shown using the sup-

plied 10–24 screws. Attach the

feeder to the stand off supports us-

ing the supplied 10–24 screws.

Y Ensure that all components

are securely fastened to the

cart before moving.

. The bottom shelf of the

Mig Runner cart is de-

signed to fit the Cool-

mate 3 water cooler.

Figure 2. Installing Power Source/Wire Feeder

Description

Part

No.

195 445

Dia.

Mkgs.

Cart, Mig Runner

Quantity

206 910 Base Assembly, Cylinder Cart 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

206 916 Shelf Assembly, Cylinder Cart 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

206 920 Bracket, Cylinder Mounting 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

163 463 Wheel, Rubber Tire 10.000 Od X 2.000 Wide X .750 Bore 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

206 986 Caster, Swivel 5.00 In Rubber/Poly Hub X 1.250 X .500–13 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

208 101 Handle Assembly 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

206 814 Label, Caution Falling Equipment 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

202 063 Label, Caution Do Not Lift 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

207 133 Kit, Accessory Mig Runner (Consisting Of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

146 296 Stand–Off, Nylon 10–24 x 1.562 lg 1/2 dia 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

207 164 Hardware Kit, Mig Runner (Consisting Of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

206 117 Chain, Cyl Double 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .