VENOM Atomik V2MR 1:10 2WD RC Buggy Kit Owner's manual

Atomik RC USA

14028 N. Ohio Street

Rathdrum, Idaho 83858

Australia

PO Box 7325

Alexandria NSW 2015

Customer Service

800.705.0620

208.762.0620 (Outside USA)

[email protected]

General Warranty Policies

Atomik™ warrants this product to be free of material and workmanship defects when new. Atomik™ will at its sole discretion repair or replace defective

components free of charge within 90 days from date of purchase or within 30 days for all electronic components. This warranty does not cover wear and tear,

crash damage, modifications, failure to perform routine maintenance, or any damages arising as a result of improper use. All warranty claims are to be directed

to Atomik™ Customer Service at 1-800-705-0620 (208-762-0620) or [email protected].

GUARANTEE

All products are inspected and adjusted individually before leaving the manufacturer and are guaranteed to be free of material defects and manufacturing

faults.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Adult supervision is required when using this product. This product should be assembled by an adult before use. Proper assembly should be checked by an

adult before use. This product should be periodically examined by an adult for potential hazards. Any potential hazardous parts should be repaired or replaced.

Important Notice

Atomik™ assumes sole responsibility for our products; therefore, dealers should not be involved in any warranty issues. All warranty claims are to be directed

to Atomik™ Customer Service. Before returning any defective product, please contact Atomik™ Customer Service at 800-705-0620 (208-762-0620) or

[email protected] to receive a Return Merchandise Authorization Number. A dated & itemized sales receipt must accompany any product

returned for warranty work.

Release of Liability

Atomik™, It’s affiliates, manufacturers, distributors, or retail partners shall not be held liable for any accident, injury to persons, or damage to property resulting

from use, misuse, or abuse of any Atomik product. In purchasing a Atomik™ product the user agrees to accept responsibility for all such risks.

This product contains chemicals known to the State of California to cause Cancer, Birth Defects and other Reproductive Harm. Be responsible, dispose of

properly.

General Warranty Policies

Atomik™ warrants this product to be free of material and workmanship defects when new. Atomik™ will at its sole discretion repair or replace defective

components free of charge within 90 days from date of purchase or within 30 days for all electronic components. This warranty does not cover wear and tear,

crash damage, modifications, failure to perform routine maintenance, or any damages arising as a result of improper use. All warranty claims are to be directed

to Atomik™ Customer Service at 1-800-705-0620 (208-762-0620) or [email protected].

GUARANTEE

All products are inspected and adjusted individually before leaving the manufacturer and are guaranteed to be free of material defects and manufacturing

faults.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Adult supervision is required when using this product. This product should be assembled by an adult before use. Proper assembly should be checked by an

adult before use. This product should be periodically examined by an adult for potential hazards. Any potential hazardous parts should be repaired or replaced.

Important Notice

Atomik™ assumes sole responsibility for our products; therefore, dealers should not be involved in any warranty issues. All warranty claims are to be directed

to Atomik™ Customer Service. Before returning any defective product, please contact Atomik™ Customer Service at 800-705-0620 (208-762-0620) or

[email protected] to receive a Return Merchandise Authorization Number. A dated & itemized sales receipt must accompany any product

returned for warranty work.

Release of Liability

Atomik™, It’s affiliates, manufacturers, distributors, or retail partners shall not be held liable for any accident, injury to persons, or damage to property resulting

from use, misuse, or abuse of any Atomik product. In purchasing a Atomik™ product the user agrees to accept responsibility for all such risks.

This product contains chemicals known to the State of California to cause Cancer, Birth Defects and other Reproductive Harm. Be responsible, dispose of

properly.

www.facebook.com/AtomikRC www.twitter.com/Atomik_RC www.youtube.com/theatomikrc

Notice of Rights

without the prior written permission of Atomik™. For information on getting permission for reprints and excerpts, contact [email protected].

Notice of Liability

The information in this manual is distributed on an “As Is” basis, without warranty. While every precaution has been taken in the preparation of the manual, Atomik™

does not have any liability to any person or entity with respect to any loss or damage caused or alleged to be caused directly or indirectly by the information

contained in this manual or by the products described in it.

10120 X 2 Ball Bearing

10229 X 2 Ball Bearing

9062 X 1 Washer Spacer

10220 X 2 Washer

9066 X 12 Steel Ball

9034 X 1 Thrust Bearing

9038 X 1 Diff Screw

9053 X 1 Diff Nut

9057 X 1 Diff Spring

10258 X 1 Pin 2 X 8

10228 X 1 Ball Bearing

10112 X 3 Ball Bearing (Rear Motor)

10112 X 5 Ball Bearing (Mid Motor)

10214 X 1 Washer

10256 X 1 Pin 5 X15.8 (Rear Motor)

10256 X 2 Pin 5 X15.8 (Mid Motor)

9042

9053

9057

9034

9038

9066

9009

10229

9062

10229

t043

9043

9041

Ball Differential

10120

10220

10120

10256

10203

10112

9029

10214

10228

9036

10258

9040

10112

9009

10112

Idler Gear

9042

1

2

5*6.5*0.5

10.2*12.4*0.2

2.38mm For Ball Diff

5 X 7.3 X 0.2

10203 X 1

O Ring (10X1.5)

Hold diff joint(9041.9042) and tighten

9009 to prevent differential from coming

loose: Be careful not to overtighten

9038. Due to the Movement of different.

Add the washer (10220)

due to the movement of the

differential in the gearbox.

Turn Upside

Down

2

Bag A

Side A

Thank you for purchasing the V2MR. This kit was designed to be fun and easy to drive using high quality parts for great perfor-

mance and durability. Please read this instruction manual thoroughly before using this product. Please pay attention to the

warnings and call out notes. The valuable tips in this manual can help prevent accidents and improper use that can lead to part

failure or injury. This kit is a High Performance R/C vehicle that requires regular maintenance for best performance. If you are

unclear on any step or are unsure about how to use your new Atomik V2MR, give our Customer Service Department a call at

800-705-0620 (208-762-0620 for International Customers) and we will be happy to help. You can also email us at

customerser[email protected].

Caliper

Nut Wrench

Side Cutters

Needle Nose

Double Sided Tape

Thread Lock

Thin CA Glue

Scissors

Hobby Knife

Ruler

Grease

Hex Driver

Shock Oil

Thank You

Recommended Tools

1

10120 X 2 Ball Bearing

10229 X 2 Ball Bearing

9062 X 1 Washer Spacer

10220 X 2 Washer

9066 X 12 Steel Ball

9034 X 1 Thrust Bearing

9038 X 1 Diff Screw

9053 X 1 Diff Nut

9057 X 1 Diff Spring

10258 X 1 Pin 2 X 8

10228 X 1 Ball Bearing

10112 X 3 Ball Bearing (Rear Motor)

10112 X 5 Ball Bearing (Mid Motor)

10214 X 1 Washer

10256 X 1 Pin 5 X15.8 (Rear Motor)

10256 X 2 Pin 5 X15.8 (Mid Motor)

9042

9053

9057

9034

9038

9066

9009

10229

9062

10229

t043

9043

9041

Ball Differential

10120

10220

10120

10256

10203

10112

9029

10214

10228

9036

10258

9040

10112

9009

10112

Idler Gear

9042

1

2

5*6.5*0.5

10.2*12.4*0.2

2.38mm For Ball Diff

5 X 7.3 X 0.2

10203 X 1

O Ring (10X1.5)

Hold diff joint(9041.9042) and tighten

9009 to prevent differential from coming

loose: Be careful not to overtighten

9038. Due to the Movement of different.

Add the washer (10220)

due to the movement of the

differential in the gearbox.

Turn Upside

Down

2

Bag A

Side A

Thank you for purchasing the V2MR. This kit was designed to be fun and easy to drive using high quality parts for great perfor-

mance and durability. Please read this instruction manual thoroughly before using this product. Please pay attention to the

warnings and call out notes. The valuable tips in this manual can help prevent accidents and improper use that can lead to part

failure or injury. This kit is a High Performance R/C vehicle that requires regular maintenance for best performance. If you are

unclear on any step or are unsure about how to use your new Atomik V2MR, give our Customer Service Department a call at

800-705-0620 (208-762-0620 for International Customers) and we will be happy to help. You can also email us at

customerser[email protected].

Caliper

Nut Wrench

Side Cutters

Needle Nose

Double Sided Tape

Thread Lock

Thin CA Glue

Scissors

Hobby Knife

Ruler

Grease

Hex Driver

Shock Oil

Thank You

Recommended Tools

1

10045 X 6 M3 X 10 CH Screw

10046 X 4 M3 X 12 CH Screw

9000

9028

9029

10068

10045

9025

9027

10046

10045

Rear Chassis Plate

5

10088

9063

9056

9011

8577

10115

9029

10068

8577

2.7mm Spacer

9023

9028

9037

10088 X 1 M4 Nylon Lock Nut

9063 X 1 Washer 4.5 X 8 X 0.8

9037 X 1 Steering Post

8577 X 3 Bell5.7-Short

9056 X 1 Steering Spring

10115 X 2 3 X 6 X 2.5 Ball Bearing

9023 X 2 Turnbuckle

30.3

10068 X 2 M3 X 10 BH Screw

3.7mm

2 pcs

Adjust according to the

track surface.

4

Bag B

4

9064 X 1 Spring Holder

10087 X 1 M3 (NyLon Nut)

9058 X 1 Slipper Spring

9045 X 2 Slipper Disk

9007

Side A

9008

9051

9007

9051

10245

10067

9045

9060

9010

9060

9045

9058

9064

10087

Transmission

Side A

Transmission

Rear Motor

Mid Motor

3

10067 X 1 M3 X 8 BH Screw

10245 X 4 M3 X 35 BH Screw

Attach spur gear so that it

rotates without wobbling

Attach spur gear so that it

rotates without wobbling

Bag A

3

10045 X 6 M3 X 10 CH Screw

10046 X 4 M3 X 12 CH Screw

9000

9028

9029

10068

10045

9025

9027

10046

10045

Rear Chassis Plate

5

10088

9063

9056

9011

8577

10115

9029

10068

8577

2.7mm Spacer

9023

9028

9037

10088 X 1 M4 Nylon Lock Nut

9063 X 1 Washer 4.5 X 8 X 0.8

9037 X 1 Steering Post

8577 X 3 Bell5.7-Short

9056 X 1 Steering Spring

10115 X 2 3 X 6 X 2.5 Ball Bearing

9023 X 2 Turnbuckle

30.3

10068 X 2 M3 X 10 BH Screw

3.7mm

2 pcs

Adjust according to the

track surface.

4

Bag B

4

9064 X 1 Spring Holder

10087 X 1 M3 (NyLon Nut)

9058 X 1 Slipper Spring

9045 X 2 Slipper Disk

9007

Side A

9008

9051

9007

9051

10245

10067

9045

9060

9010

9060

9045

9058

9064

10087

Transmission

Side A

Transmission

Rear Motor

Mid Motor

3

10067 X 1 M3 X 8 BH Screw

10245 X 4 M3 X 35 BH Screw

Attach spur gear so that it

rotates without wobbling

Attach spur gear so that it

rotates without wobbling

Bag A

3

Front Arm

9

10067 X 2 M3 X 8 BH Screw

10051 X 4 M2 X 4 BH Screw

10251 X 2 Pin 3 x 26

10254 X 2 Pin 3 x 32.9

9050 X 1 Suspension Mount

9023 X 2 Turnbuckle

9001

9029

10251

10051

10067

9050

9026

10254

10051

9023

9028

10

Front Arm

Attaching Front Arms

30.8

2mm Spacer

4 pcs

6

Bag D

10087

10115

10045

9011

10115

10045

10253

9011

10087 X 2 M3 Nylon Lock Nut

10253 X 1 Pin 3 X 31.2mm

10115 X 4 3 X 6 X 2.5 Ball Bearing

10045 X 3 M3 X 10mm CH Screw

Steering

7

Steering

8

9035A

10067

8577

9035A

10051

10204

8577

10087

9019

10051

8568

10204

9019

10087

9011

10067 X 2 M3 X 8 BH Screw

8577 X 2 Ball 5.7-Short

10087 X 2 M3 Nylon Lock Nut

10204 X 4 Washer 3 x 6 x 0.2

10051 X 2 M2 X 4 BH Screw

8568 X 2 Pin 3 x 24

9035A X 2 Front Axle

9035B X 2 Front Axle

8568

8577 X 2 Ball 5.7-Long

9035A For 5.0(ID) Bearing

9035B For 3/16”(ID) Bearing

5

Bag C

Front Arm

9

10067 X 2 M3 X 8 BH Screw

10051 X 4 M2 X 4 BH Screw

10251 X 2 Pin 3 x 26

10254 X 2 Pin 3 x 32.9

9050 X 1 Suspension Mount

9023 X 2 Turnbuckle

9001

9029

10251

10051

10067

9050

9026

10254

10051

9023

9028

10

Front Arm

Attaching Front Arms

30.8

2mm Spacer

4 pcs

6

Bag D

10087

10115

10045

9011

10115

10045

10253

9011

10087 X 2 M3 Nylon Lock Nut

10253 X 1 Pin 3 X 31.2mm

10115 X 4 3 X 6 X 2.5 Ball Bearing

10045 X 3 M3 X 10mm CH Screw

Steering

7

Steering

8

9035A

10067

8577

9035A

10051

10204

8577

10087

9019

10051

8568

10204

9019

10087

9011

10067 X 2 M3 X 8 BH Screw

8577 X 2 Ball 5.7-Short

10087 X 2 M3 Nylon Lock Nut

10204 X 4 Washer 3 x 6 x 0.2

10051 X 2 M2 X 4 BH Screw

8568 X 2 Pin 3 x 24

9035A X 2 Front Axle

9035B X 2 Front Axle

8568

8577 X 2 Ball 5.7-Long

9035A For 5.0(ID) Bearing

9035B For 3/16”(ID) Bearing

5

Bag C

Rear Arm

13

Mid Motor

Rear Motor

10051 X 2 M2 X 4 BH Screw

10255 X 2 Pin 3 X 51.6

10255

10051

10255

10051

8

Bag F

11

10068

10241

10232

9013

8577

9012

10068

10047

9015

Attaching Front Shock Tower

10232 X 2 M3 Ni-Plated Nut

10068 X 6 M3 X 10 BH Screw

10241 X 2 M3 X 22 BH Screw

10047 X 4 M3 X 14 CH Screw

8577 X 2 Ball 5.7-Long

8577 X2 Ball 5.7-Long

10087 X 2 M3 Nylon Lock Nut

10087

9018

8577

9029

10252

9002

10252

8577

10087

9018

9029

9018

10051

8577

9002

9018

10252

10051

9002

12

Mid Motor

Rear Arm

Rear Motor

10252 X 2 Pin 3 X 27

10051 X 2 M2 X 4 BH Screw

1mm Spacer

2 pcs

7

Bag E

Bag F

Rear Arm

13

Mid Motor

Rear Motor

10051 X 2 M2 X 4 BH Screw

10255 X 2 Pin 3 X 51.6

10255

10051

10255

10051

8

Bag F

11

10068

10241

10232

9013

8577

9012

10068

10047

9015

Attaching Front Shock Tower

10232 X 2 M3 Ni-Plated Nut

10068 X 6 M3 X 10 BH Screw

10241 X 2 M3 X 22 BH Screw

10047 X 4 M3 X 14 CH Screw

8577 X 2 Ball 5.7-Long

8577 X2 Ball 5.7-Long

10087 X 2 M3 Nylon Lock Nut

10087

9018

8577

9029

10252

9002

10252

8577

10087

9018

9029

9018

10051

8577

9002

9018

10252

10051

9002

12

Mid Motor

Rear Arm

Rear Motor

10252 X 2 Pin 3 X 27

10051 X 2 M2 X 4 BH Screw

1mm Spacer

2 pcs

7

Bag E

Bag F

10241

9029

10068

8577

9029

10241

9017

9012

10232

10068

10232

10005

(Not Included)

10068

9017

9013

10241

9013

10005

9029

10232 X 2 M3 Nut Ni-Plated

10068 X 7

M3 X 10 BH Screw

Rear Motor

10068 X 3

M3 X 10 BH Screw

Mid Motor

10241 X 2

M3 X 22 BH Screw

10005 X 2

M2 X 8 SH Screw

(Not Included)

8577 X 2 Ball5.7-long

Attaching Shock Tower

15

Rear Motor

Mid Motor

(Not Included)

9029

(Not Included)

9029

10

Bag G

Rear Motor

Mid Motor

10047

10047X 4 M3 X 14 CH Screw

Attaching Transmission

14

9

Bag F

10241

9029

10068

8577

9029

10241

9017

9012

10232

10068

10232

10005

(Not Included)

10068

9017

9013

10241

9013

10005

9029

10232 X 2 M3 Nut Ni-Plated

10068 X 7

M3 X 10 BH Screw

Rear Motor

10068 X 3

M3 X 10 BH Screw

Mid Motor

10241 X 2

M3 X 22 BH Screw

10005 X 2

M2 X 8 SH Screw

(Not Included)

8577 X 2 Ball5.7-long

Attaching Shock Tower

15

Rear Motor

Mid Motor

(Not Included)

9029

(Not Included)

9029

10

Bag G

Rear Motor

Mid Motor

10047

10047X 4 M3 X 14 CH Screw

Attaching Transmission

14

9

Bag F

10112

17

Rear Motor

10067

10068

10067

Rear Shock Tower

10067 X 4 M3 X 8 BH Screw

10068 X 2 M3 X 10 BH Screw

10112 X 2 5 X 10 X 4mm Bearing

12

Bag H

CVD & Rear Turnbuckle Set

16

23.5

1:1

30

1:1

10013

9023

9028

9039

9067

Rear Motor Mid Motor

10044 X 2 M3 X 8 CH Screw

9067 X 2 Pin2.0 X 10 (With Groove)

10013 X 2 M3 X 3 Set Screw

9023 X 2 Turnbuckle

8577

9024

10044

2 sets2 sets

11

Bag H

10112

17

Rear Motor

10067

10068

10067

Rear Shock Tower

10067 X 4 M3 X 8 BH Screw

10068 X 2 M3 X 10 BH Screw

10112 X 2 5 X 10 X 4mm Bearing

12

Bag H

CVD & Rear Turnbuckle Set

16

23.5

1:1

30

1:1

10013

9023

9028

9039

9067

Rear Motor Mid Motor

10044 X 2 M3 X 8 CH Screw

9067 X 2 Pin2.0 X 10 (With Groove)

10013 X 2 M3 X 3 Set Screw

9023 X 2 Turnbuckle

8577

9024

10044

2 sets2 sets

11

Bag H

9016

10067

10044

10240

9029

Motor Guard / Rear Bumper

18

Rear Motor

Mid Motor

10044

10043

9016

10240 X 2 M3 X 15 BH Screw

14

10067 X 2 M3 X 8 BH Screw

10044 X 2 M3 X 8 CH Screw

10043 X 2 M3 X 6 CH Screw

Bag I

10240

10069

Mid Motor

10112

10112 X 2 5 X 10 X 4mm Bearing

10240 M3 X 15 BH Screw

10069 M3 X 12 BH Screw

13

9016

10067

10044

10240

9029

Motor Guard / Rear Bumper

18

Rear Motor

Mid Motor

10044

10043

9016

10240 X 2 M3 X 15 BH Screw

14

10067 X 2 M3 X 8 BH Screw

10044 X 2 M3 X 8 CH Screw

10043 X 2 M3 X 6 CH Screw

Bag I

10240

10069

Mid Motor

10112

10112 X 2 5 X 10 X 4mm Bearing

10240 M3 X 15 BH Screw

10069 M3 X 12 BH Screw

13

1mm 1mm

9049

10005

10201

9046

9047

10200

9032

9033

9048

9028

9048

9031

9028

10224

9029

10202

9029

1. Pull down piston and pour oil into

body. Remove air bubbles by slowly

moving piston up and down.

2. Pull down piston and check amount

of oil and tighten shock cap.

Shock F/R Assembly

Shock Oil

20

21

10224 X 8 2.3mm E-Clip

9049 X 4 Spring Retainer

10005 X 4 M2 X 8 SH Screw

9032 X 2 Front Shock Shaft

9033 X 2 Rear Shock Shaft

9028 Piston 4 Holes

(STD.)

10202 X 8 “O” Ring 7 X 2.2

10200 X 4 “O” Ring 16.5 X 1

10210 X 4 “O” Ring 18.2 X 1.6

Front Shock 2 pcs

Rear Shock 2 pcs

Use when the air

pressure hole (1.5mm)

on the 9031 is open.

1mm Spacer

4 pcs

1mm Spacer

4 pcs

16

Bag J

10067 X 2 M3 X 8 BH Screw

ESC Mount

19

Rear Motor

Motor Braces

Mid Motor

10240 X 1 M3 X 15 BH Screw

10044 X 2 M3 X 8 CH Screw

10241 X 1 M3 X 22 BH Screw

10067

9030

10067

9065

10240

10241

10044

15

Bag I

1mm 1mm

9049

10005

10201

9046

9047

10200

9032

9033

9048

9028

9048

9031

9028

10224

9029

10202

9029

1. Pull down piston and pour oil into

body. Remove air bubbles by slowly

moving piston up and down.

2. Pull down piston and check amount

of oil and tighten shock cap.

Shock F/R Assembly

Shock Oil

20

21

10224 X 8 2.3mm E-Clip

9049 X 4 Spring Retainer

10005 X 4 M2 X 8 SH Screw

9032 X 2 Front Shock Shaft

9033 X 2 Rear Shock Shaft

9028 Piston 4 Holes

(STD.)

10202 X 8 “O” Ring 7 X 2.2

10200 X 4 “O” Ring 16.5 X 1

10210 X 4 “O” Ring 18.2 X 1.6

Front Shock 2 pcs

Rear Shock 2 pcs

Use when the air

pressure hole (1.5mm)

on the 9031 is open.

1mm Spacer

4 pcs

1mm Spacer

4 pcs

16

Bag J

10067 X 2 M3 X 8 BH Screw

ESC Mount

19

Rear Motor

Motor Braces

Mid Motor

10240 X 1 M3 X 15 BH Screw

10044 X 2 M3 X 8 CH Screw

10241 X 1 M3 X 22 BH Screw

10067

9030

10067

9065

10240

10241

10044

15

Bag I

9028

8577 X 1 Ball 5.7 (Short)

10241

9029

10067

8577

9031

M3 X 6 BH Screw

Use for Futaba Servo

Use for JR/SANWA Servo

Servo

10241

10087

9054 X 2 Shock Spring - Front

10241 X 2 M3 X 22 BH Screw

Attaching Front Shocks

Front Shocks

24

25

Steering Servo Asembly

26

9054

9028

10087

10067 X 4 M3 X 8 BH Screw

2 pcs2 pcs

10087 X 2 M3 Nylon Lock Nut

18

Bag J

Bag K

9055

9028

10240

9028

10087

10240

10087

9028

Attaching Rear Shocks

Rear Shocks

22

9055 X 2 Shock Spring - Rear

10087 X 2 M3 Nylon Lock Nut

10240 X 2 M3 X 15 BH Screw

Mid Motor

Rear Motor

23

10240

9028

2 pcs2 pcs

9028

17

Bag J

9028

8577 X 1 Ball 5.7 (Short)

10241

9029

10067

8577

9031

M3 X 6 BH Screw

Use for Futaba Servo

Use for JR/SANWA Servo

Servo

10241

10087

9054 X 2 Shock Spring - Front

10241 X 2 M3 X 22 BH Screw

Attaching Front Shocks

Front Shocks

24

25

Steering Servo Asembly

26

9054

9028

10087

10067 X 4 M3 X 8 BH Screw

2 pcs2 pcs

10087 X 2 M3 Nylon Lock Nut

18

Bag J

Bag K

9055

9028

10240

9028

10087

10240

10087

9028

Attaching Rear Shocks

Rear Shocks

22

9055 X 2 Shock Spring - Rear

10087 X 2 M3 Nylon Lock Nut

10240 X 2 M3 X 15 BH Screw

Mid Motor

Rear Motor

23

10240

9028

2 pcs2 pcs

9028

17

Bag J

10013

10044

10066

9029

10068

10067

Mid Motor

10068 X 1 M3 X 10 BH Screw

10044 X 2 M3 X 8 CH Screw

10066 X 1

M3 X 6 BH Screw

9014

20

Motor

10045

9028

10014

Motor

9014

Installing Steering Servo

27

Installing Motor

28

10013 X 1 M3 X 3mm Set Screw

10067 X 2 M3 X 8 BH Screw

9052 X 1 Pinion Gear 20T (STD.)

10013

9052

10045 X 2 M3 X 10 CH Screw

10014 X 2 M3 X 10 Set Screw

Tighten the screws with

on sheet of paper inserted

between both gears.

Rear Motor

10067

10066

9029

10066

10066 X 2

M3 X 6 BH Screw

9028

19

Pinion

Gear

Spur Gear

77T

9.53

9.10

8.70

8.34

8.01

79T

10.27

9.78

9.34

8.93

8.56

8.22

20T

21T

22T

23T

24T

25T

Bag K

5mm

Page is loading ...

VENOM Atomik V2MR 1:10 2WD RC Buggy Kit Owner's manual

VENOM Atomik V2MR 1:10 2WD RC Buggy Kit Owner's manual

Related papers

Other documents