IMC Networks PSE-McBasic Series Features And Benefits
- Category
- Network media converters
- Type
- Features And Benefits
IMC Networks PSE-McBasic Series offers unparalleled flexibility and cost-effectiveness by supporting the IEEE 802.3af PoE standard. Designed for various installation scenarios, it features options for multi-mode or single-mode fiber, single-strand fiber, and extreme temperature models. With its copper-to-fiber conversion capability, troubleshooting features, and compact design, the PSE-McBasic Series simplifies network infrastructure expansion and powers devices up to 100 meters away.
IMC Networks PSE-McBasic Series offers unparalleled flexibility and cost-effectiveness by supporting the IEEE 802.3af PoE standard. Designed for various installation scenarios, it features options for multi-mode or single-mode fiber, single-strand fiber, and extreme temperature models. With its copper-to-fiber conversion capability, troubleshooting features, and compact design, the PSE-McBasic Series simplifies network infrastructure expansion and powers devices up to 100 meters away.
800-624-1070
www.imcnetworks.com
Features and Benefits
Employs the IEEE 802.3af Power Over
Ethernet Standard
Significant cost-savings; no need to extend •
existing power/cabling to supply power to
a device
Provides greater installation flexibility; •
choose the best location for a powered
device
Meets a multitude of installation
requirements
Available for multi-mode or single-mode •
fiber
Available for single-strand fiber •
The XT model allows for operation in •
temperatures of up to 65°C
Available with ST or SC fiber connectors•
Eases troubleshooting
LinkLoss and FiberAlert features assist •
in diagnosing problems on fiber optic
networks
Ethernet-based, Standalone Media Converters
PSE-McBasic Series
Supporting the IEEE 802.3af PoE standard, the standalone PSE-McBasic
media converter offers unparalleled installation flexibility and cost-
savings.
Connecting and powering small devices at the edge of a wired
network infrastructure becomes increasingly important to LANs/
MANs as they add WiFi access points, webcams, entry control
systems, etc. Sometimes, the most optimal location for one of
these devices is not only out of reach of the existing copper wiring,
but also too far from an AC power source. Deploying a media
converter supporting the Power Over Ethernet standard is the
solution for both extending an access point up to 100 Km from the
central office equipment as well as powering the end-device.
Equipped with all the features that have made the McBasic series
one of IMC Networks’ most popular brands — copper-to-fiber
conversion, troubleshooting capability, a small, rugged design, and
an internal AC power supply — the 100 Mbps PSE-McBasic also
employs the IEEE 802.3af Power Over Ethernet (PoE) standard.
Power Over Ethernet technology
Power Over Ethernet technology allows the PSE-McBasic to be the
Power Source Equipment (PSE) by distributing an electrical current
across existing copper data cabling. If the connected unit requires
power and is 802.3af compliant, the PSE-McBasic detects it and
supplies power. LEDs on the PSE-McBasic indicate the amount
of power being supplied to the “Powered Device” (PD) as well as
if the PSE-McBasic is over temperature or over current or has an
open circuit.
Also available is an Extreme Temperature model:
The PSE-XT-McBasic has an operating temperature of up to 65°C,
perfect for installing in even the hottest of conditions.
RoHS Compliant
Application Example
Incorporating the PoE standard into the
product design allows network administrators
to install the PSE-McBasic up to 100 meters
from an access point while support of single-
mode fiber allows installation of the media
converter up to 80 Km from a central office
(CO) switch. The best location for a WiFi
access point, for example, may be on a utility
pole outside or in the ceiling where there is
no AC outlet. The PSE-McBasic makes the
connection between the CO switch, via single
or multi-mode fiber, and a twisted pair access
point while also providing power to a WiFi
device.
Using the PoE technology, the PSE-McBasic
becomes the Power Source Equipment for
the Powered Device. This gives installers
greater installation flexibility since the access
device no longer has to be in the immediate
proximity of an AC power source and/or UPS.
DS-PSE-McBasic-0710
Copyright © 2007 IMC Networks. All rights reserved.
The information in this document is subject to
change without notice. IMC Networks assumes
no responsibility for any errors that may appear in
this document. Specific product names may be
trademarks or registered trademarks and are the
property of their respective companies.
IMC Networks
Fiber Consulting Services
For information call:
TEL: 949-465-3000
1-800-624-1070 (US/CAN)
+32-16-550880 (Europe)
IMC Networks
Headquarters
19772 Pauling
Foothill Ranch, CA 92610
TEL: 949-465-3000
FAX: 949-465-3020
www.imcnetworks.com
IMC Networks
Europe
Herseltsesteenweg 268
B-3200 Aarschot | Belgium
TEL: +32-16-550880
FAX: +32-16-550888
IMC Networks
Eastern US/Latin America
18840 US Hwy. 19 North Suite 400
Clearwater, FL 33764
TEL: 727-524-8152/524-8071 (Latin)
FAX: 727-524-8432
Fiber Optics Specifications
For each product listed below in the Ordering Information section, the DISTANCE represents an approximate fiber distance based on industry-
standard fiber attenuation specifications. Actual distances will vary for each installation. For complete power budgets and information on calculating
specific distances, visit www.imcnetworks.com/go/fcs or contact IMC Networks Fiber Consulting Services at 949-465-3000.
*These products have single-strand fiber technology. Deploy in pairs, or connect to another compatible IMC Networks single-strand fiber product. For more
information go to: www.imcnetworks.com/products/SSFX.cfm
Ordering Information
Technical Specifications
IEEE 802.3u 100Base-TX twisted pair•
IEEE 802.3u 100Base-FX or SX fiber•
IEEE 802.3af: Acts as a PSE – Power sourcing device•
Includes fixed, internal AC power•
AutoCross for MDI-II/MDI-X; plus switch for manual •
configuration
Features LinkLoss and FiberAlert•
Features Auto-Negotiation•
50/125µm or 62.5/125µm multi-mode•
9/125µm single-mode •
Available for single-strand fiber•
Connectors: RJ-45, and ST or SC•
Small, rugged design•
Supports Half- and Full-Duplex operation•
Includes diagnostic LEDs•
Regulatory Approvals:
FCC Class A•
UL/cUL, CSA, CE•
Dimensions:
1.45”H x 4.73”W x 7.30”D
(3.68 cm x 12.01 cm x 18.54 cm)
Shipping Weight:
1.8 lbs (.82 kg)
Power Rating:
100-240V AC, 50/60 Hz, 1A
Operating Temperature:
32° to 122° F (0° to +50° C); -4° to 149° F (-20° to +65° C)
for PSE-XT-McBasic
5% to 90%, noncondensing, 0 – 10,000 ft. altitude
Storage Temperature:
-13° to +158°F (-25° to +70°C); -4° to 185° F (-20° to
+85° C) for PSE-XT-McBasic
5% – 90% (non-condensing)
PART # DESCRIPTION DISTANCE
PSE PSE-XT
855-16927 855-17927 TX/FX-MM1300-ST 2 km
855-16928 855-17928 TX/FX-MM1300-SC 2 km
855-16929 --- TX/SX-MM850-ST 2 km
855-16930 --- TX/SX-MM850-SC 2 km
855-16931 855-17937 TX/FX-SM1310/PLUS-ST 40 km
855-16932 855-17938 TX/FX-SM1310/PLUS-SC 40 km
855-16933 855-17939 TX/FX-SM1310/LONG-ST 80 km
855-16934 855-17960 TX/FX-SM1310/LONG-SC 80 km
855-16935 855-17961 TX/FX-SM1550/LONG-SC 80 km
Single-Strand Fiber *
855-16951 855-17951 TX/SSFX-SM1310-SC (1550rcv) 20 km
855-16952 855-17952 TX/SSFX-SM1550-SC (1310rcv) 20 km
855-16953 855-17953 TX/SSFX-SM1310/PLUS-SC (1550rcv) 40 km
855-16954 855-17954 TX/SSFX-SM1550/PLUS-SC (1310rcv) 40 km
855-16955 855-17955 TX/SSFX-SM1310/LONG-SC (1550rcv) 60 km
855-16957 855-17956 TX/SSFX-SM1550/LONG-SC (1310rcv) 60 km
PART # DESCRIPTION
Rackmount/Wallmount Accessories
895-39226 McBasic, MediaChassis, AccessEtherLInX Rackmount Brackets
895-39227 McBasic, MediaChassis, AccessEtherLinX Wallmount Brackets
895-39228 McBasic, MediaChassis, AccessEtherLinX x3 Rackmount Shelf
895-39949 McBasic, iMediaChassis/3, MediaChassis, AccessEtherLinX Rackmount Shelf
-
1
-
2
IMC Networks PSE-McBasic Series Features And Benefits
- Category
- Network media converters
- Type
- Features And Benefits
IMC Networks PSE-McBasic Series offers unparalleled flexibility and cost-effectiveness by supporting the IEEE 802.3af PoE standard. Designed for various installation scenarios, it features options for multi-mode or single-mode fiber, single-strand fiber, and extreme temperature models. With its copper-to-fiber conversion capability, troubleshooting features, and compact design, the PSE-McBasic Series simplifies network infrastructure expansion and powers devices up to 100 meters away.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
IMC Networks 854-17646 User manual
-
IMC Networks PSE-McBasic Series User manual
-
IMC Networks 855-11826 Datasheet
-
IMC Networks McBasic TX/FX Operating instructions
-
IMC Networks McBasic, TX/SSFX-SM1310/LONG-SC User manual
-
IMC Networks McBasic Gigabit Installation guide
-
IMC Networks McBasic TX/FX Installation guide
-
IMC Networks McBasic Installation guide
-
-
IMC Networks 852-10153 Datasheet
