Kenmore GTUP240EM4WW Installation guide

Installation

Instructions

Unitized Electric

Washer/Dryer

Questions on installation? Call: 1-800-GECARES {US} or Visit our Web site at: www.GEAppliances.com (US).

In Canada, call 800.561.3344 or visit www.GEAppliances.cu

i

BEFORE YOU BEGIN

Readthese instructions completely and

carefully.

• IMPORTANT- savethese instructions for

localinspector's use.

• IMPORTANT- Observeall governing codes

and ordinances.

• Note to Installer - Be sure to leave these

instructionswith the customer.

Note to Customer- Keepthese instructionswith

your Owner's Hanual for future reference.

• Beforethe appliance is removedfrom serviceor

discarded,remove thewasher and dryer doors.

Inspect the dryer exhaust outlet and straighten

the outlet walls ifthey are bent.

Service information and the wiring diagram are

located at the accesspanel.

Do not allow children on or in the appliance.

Closesupervision of children isnecessarywhen

the appliance isusednear children.

Install the appliance where the temperature is

above 50°F for satisfactory operation of the

control system.

• Productfailure due to improper installation isnot

coveredunder the Warranty.

_LW_KI_I|I_I£_" RISK OF FIRE

. To reduce the risk of severe injury or death, follow all installation

instructions.

Appliance installation must be performed by a qualified installer.

Install the appliance according to these instructions and in accordance

with local codes.

This appliance must be exhausted to the outdoors.

Use only 4" rigid metal ducting for exhausting the clothes dryer to the

outdoors.

DO NOT install a clothes dryer with flexible plastic ducting materials.

If flexible metal (semi-rigid or foil-type) duct is installed, it must be

UL listed and installed in accordance with the instructions found

in "Connecting The Dryer To House Vent" on page 8 of this manual.

Flexible venting materials are known to collapse, be easily crushed,

and trap lint. These conditions will obstruct dryer airflow and increase

the risk of fire.

Do not install or store this appliance in any location where it could be

exposed to water and or weather.

Save these instructions. (Installers: Be sure to leave these instructions

with the customer).

NOTE: installation and service of this appliance requires basic

mechanical and electrical skills, it is your responsibility to

contact a qualified installer to make the electrical connections.

TOOLS YOU WILL NEED

Slip Pliers

Phillips Screwdriver

Flat-blade Screwdriver

1/4" Nutdriver

Level

#' DFA.METALDUCT

(RECOMMENDED/

MATERIALS YOU WILL NEED

#' DUCT

#' DFAFLEXBLEMETAL(SEMFREGED} CLAMPS(2}

ULLISTEDTRANSITIONDUCT

(IFNEEDED} OR

P

KITWXO8XlO077(INCLUDES2 ELBOWS} #' SPRING

CLAMPS(2}

%

#' DIA.METAL

ELBOW

%

EXHAUST SAFETY

HOOD GLASSES

#' DFA.FLEXBLEMETAL(FOELTYPE} _ 3/#'STRAEN

ULLISTEDTRANSITIONDUCT

x,4

(iFNEEDED,} DUCTTAPE GLOVES RELIEF

4"COVERPLATE(iFNEEDED/ ULRECOGNIZED

(KiTWE1M454}

APPLIANCEPOWER

CORDKIT

(NOTPROVIDED/

ULRATED

120/2@V,}OA

WITH3 OR4PRONGS,

IDENTIFYTHEPLUG

TYPEASPERTHE

HOUSERECEPTACLE

BEFOREPURCHASING

LiNECORD,

PARTS SUPPLIED

1 Cable Tie

% oo

2 Rubber Washers 2 Stainer Screens/

Rubber Washers

(washers may be in water hoses)

2 Washer Hoses

Printedin Mexico 233DI835PO02 31-16652-5 12-12 GE

Installation instructions

INSTALLATION REQUIREMENTS LOCATION

This appliance must be installed on firm flooring to minimize

vibration during spin cycle. Concrete flooring is best, but

wood base is sufficient, provided floor support meets FHA

standards. This appliance should not be installed on rugs or

exposed to weather.

PLUMBING

WATERPRESSURE- Must be 20 psi minimum to 120 psi

maximum.

WATERTEMPERATURE- Householdwater heater should be set

to deliverwater at 120°to !50°F (50°to 66°C)INTHEWASHER

when hot wash isselected.

SHUTOFFVALVES- Both hot and cold shutoffvalves (faucets)

should be supplied.

DRAIN- Water may be drained into standpipe or set tub.

Discharge height MUSTNOTBELESSTHAN30 INCHES,and

no more than 8 feet above the baseof the washer. Standpipe

must be 1-1/2 inches minimum insidediameter and must be

open to atmosphere.

ELECTRICAL REQUIREMENTS

CAUTION: Before plugging in washer, read the following

electrical requirements.

CAUTION: For personal safety, do not use an extension

cord or adapter plug with this appliance. Do not, under any

circumstances, cut or remove the third grounding prong

from the power cord. Follow national electrical codes and

ordinances. This appliance must be supplied with the voltage

and frequency indicated on the rating plate (located at the

top of the dryer front panel),and connected to an individual,

properly grounded branch circuit, protected by a 30-amp

circuit breaker or time-delay fuse. If the electric supply

provided doesnot meet the aboverequirements, calla licensed

electrician.

Step ! Prepare the Area and Exhaust for Installation of

Appliance (seesection !).

Step 2 Check and Ensure the Existing External Exhaust is

Clean (seesection !) and Meets Attached Installation

Specifications (seesection 3).

Step 3 Removethe Foam Shipping Pads (seesection !).

Step 4 Hove the Appliance to the Desired Location.

Step 5 Connect the Power Supply (seesection 2).

Step 6 Connect the External Exhaust (seesection 4).

Step 7 LevelYour Appliance (seesection 5).

Step 8 Connect to plumbing facilities (seesection 8).

Step 9 Check the Operation of the Power Supply

and Venting.

Step !0 Place the Owners Manual and the Installation

Instructions in a Location Where They Will Be Noticed Bythe

Owner.

For Alcove or Closet Installation, see section !0.

For Bathroom or Bedroom Installation, see section !!.

For Mobile or Manufactured Home see, section 9.

For side or bottom exhaust, see section 6.

2

7_._c

Installation Instructions

24" NOMINAL PRODUCT DIMENSIONS

51"

!9.1 "J

0ool oo " 0

Water Inlets

(rear) _

,_------*23.75"--------_

--- 43"--------€

* Dimension represents door closed including handle and knobs.

NOTE:With feet set at mid position, feet can be adjusted +_.375".

Gas Inlet

(Rearview of appliance)

27" NOMINAL PRODUCT DIMENSIONS

52.9"

0oolo o , 0

Vent_.Q_..

_._._.. Drain outlet

i (rear)

p3.9"

-_----- 26.8"

4------'26.7"-----_

-- !2.5"

--47"_

Waterlnlets

(rear) 5i_°

36.5"

4.35"

__ m

",_----- 30.85"------_

* Dimension represents door closed including handle and knobs.

NOTE:With feet set at mid position, feet can be adjusted +_575".

Gas Inlet

(Rearview of appliance)

[

Installation Instructions

Minimum Clearance Other Than Alcove or Closet Installation

Minimum clearance to combustible surfaces and for air opening are: 0 in. clearance both sides and rear.Consideration must

be given to provide adequate clearance for installation and service.

_-I PREPARING FOR INSTALLATION

OF NEW APPLIANCE

REMOVING LINT FROM WALL EXHAUST

OPENING

• Remove and discard existing plastic or metal foil

transition duct and replace with ULlisted transition duct.

WALL

/

INTERNALDUCT

CHECKTHATEXHAUST

OPENING HOODDAMPEROPENS

ANDCLOSESFREELV.

TILTTHE APPLIANCE

SIDEWAYS AND REMOVE

THE FOAM SHIPPING PADS

BY PULLING ATTHE SIDES

AND BREAKING THEM

AWAY FROM THE APPLIANCE

LEGS.BE SURE TO REMOVE

ALL OFTHE FOAM PIECES

AROUND THE LEGS.

After the machine is in the

home, remove remaining

packing material/carton from

washer.

DO NOT REMOVE SHIPPING

RODAT THISTIME.

Remove styrofoam block.

Remove the bag containing

the Washer hoses and parts

parts from tub. Putstyrofoam

block back in tub opening to

hold tub in place during the

rest of installation.

Hove washer close to final

position. Make sure there is

at least a 24" clearance on

right sideof washer to remove

shipping bar. PULLSHIPPING

BAR OUT USING YELLOW

PLASTICHANDLE.Keepbar so

it can be reinstalled if washer

isever moved again.

Styrofoam BlocJ_

Washer hoses

and parts

II

I

Shipping

Bar

Yellow plastic handle

4

NEW HOME OR REMODELING FAUCETS/

DRAI N STANDPIPEIELECTRICAL LOCATION

Right side of

Laundry Center.

.................. _|

Locate spigots, "

drain standpipe ss" |

and electrical plug |

1

in this area

!

FLOOR

[] ELECTRICAL CONNECTION INFORMATION

A WAR N IN G -TOREDUCETHERISKOF

FIRE,ELECTRICALSHOCK AND PERSONAL INJURY:

• DO NOT USE AN EXTENSION CORD OR AN

ADAPTER PLUG WITH THIS APPLIANCE.

Thisdryer must be electrically grounded in accordance

with local codes,or inthe absence of localcodes,with the

National ElectricalCode,ANSI/NFPANO.70 or Canadian

ElectricalCode,CSAC22.1.

ELECTRICAL REQUIREMENTS

This appliance must be connected to an individual

branch circuit, protected by the required time-delay

fuses or circuit breakers. A four or three-wire, single

phase, 120/240V or 120/208V, 60Hz, 30 amp circuit

is required. If the electric supply does not meet the

above specifications, then call a licensed electrician.

GROUNDING INSTRUCTIONS

a.

For a grounded, cord-connected appliance:

This appliance must be grounded. In the event of

malfunction or breakdown, grounding will reduce

the risk of electric shock by providing a path of

least resistance of electric current. This appliance is

equipped with a cord having an equipment-grounding

conductor and a grounding plug. The plug must be

plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local

codes and ordinances.

WARNING -Improper connection of the

equipment-grounding conductor can result in a risk

of electric shock. Check with e qualified electrician

or servicemen if you are in doubt us to whether the

appliance is properly grounded.

Installation

GROUNDING INSTRUCTIONS {Cont.}

Do not modify the plug provided with the appliance. If it

will not fit the outlet, have a proper outlet installed by a

qualified electrician.

B.Fordirect-wire connected appliance:

This appliance must be connected to a grounded, metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment grounding terminal or lead

on the appliance.

ELECTRICAL CONNECTION LOCATION

24" MODELS 27" MODELS

CONNECTING DRYER USING 3-WIRE

CONNECTION

GREEN GROUND

GROUND STRAP

SCREW

NOT

WIRE STRAINRELIEF

BRACKET

3/4",UL

RECOGNIZED

RELIEF

NEUTRAL

(White) HOT

WIRE

] #i0 AWGMINIMUMCOPPER

COVER CONDUCTORSOR220/240V]ORPOWER

SUPPLYCORDKITMARKEDFORUSE

WITHDRYERS&PROVIDEDWITHCLOSED

LOOPORSPADETERMINALSWITH

3-wi re Connection UPTURNEDENDS{NOTSUPPLIED},

Not for use in Canada.

DONOTuse for Mobile Home Installations.

NOTfor use on new construction.

NOTfor use on recreational vehicles.

NOTfor use in areas where local codes prohibit grounding

through the neutral conduction.

1.Turn off the circuit breaker(s) (50 amp) or remove the

dryer's circuit fuse at the electrical box.

2. Be sure the appliance cord isunplugged from the wall.

3. Removethe power cord cover located at the lower back.

4. Install 3/4 in. UL recognized strain relief to power cord

entry hole. Bring power cord through strain relief.

nstructions

5. Connect power cord as follows:

A. Connect the 2 hot lines to the outer screws of the

terminal block (marked L1 and L2).

B.Connect the neutral (white) line to the center of the

terminal block (marked N).

6. Be sure ground strap is connected to neutral (center)

terminal of block and to green ground screw on cabinet

rear.Tighten all terminal block screws (3)securely.

7. Properly secure power cord to strain relief.

8. Reinstall the cover.

_:LVV/AKI_Iil_I_: NEVER LEAVE THE

COVER OFF OF THE TERMINAL BLOCK.

CONNECTING APPLIANCE USING 4-WIRE

CONNECTION {MUST BE USED FOR

MOBILE HONE INSTALLATION}

NOTES:Since January 1,1996, the National Electric code

requires that the new constructions utilize a 4-wire

connection to an electric dryer.

WARN ING:onlya4-conductorcordshallbe

used when the appliance is installed in a location where

grounding through the neutral conductor is prohibited.

Grounding through the neutral is prohibited for the new

branch-circuit installations, mobile homes, recreational

vehicles, and areas where local codes prohibit grounding

through the neutral conduction.

REHOVEGROUNDSTRAP

ANDDISCARDKEEPGREEN

GROUNDSCREW[oF_ WIRE RELOCATEGREEN

GROUNDSCREW

"\_,_ HERE GREENOR

RELIEF

BRACKET

COVER

HOT

WIRE

3/4",UL /_

RECOGNIZED

STRAIN RELIEF

4 #10 AWGMINiMUMCOPPER

CONDUCTORSOR120/240V 30A POWER

SUPPLYCORDKIT MARKEDFORUSE

WITHDRYERS& PROVIDEDWITH

CLOSEDLOOPORSPADETERMINALS

WITHUPTURNEDENDS(NOTSUPPLIED)

1.Turn off the circuit breaker (s)(30 amp) or remove the

dryer's circuit fuse at the electrical box.

2. Be sure the appliance cord is unplugged from the wall

receptacle.

3. Removethe power cord cover located at the lower back.

4. Remove and discard ground strap. Keep the green

ground screw for step 7.

5. Install 3/4 in. ULrecognized strain relief to power cord

entry hole. Bring power cord through strain relief.

Installation instructions

CONNECTING APPLIANCE USING 4-WIRE

CONNECTION (MUST BE USED FOR

MOBILE HOME INSTALLATION} (Cont.}

6.Connect power cord as follows:

A. Connect the 2 hot lines to the outer screws of the

terminal block (marked L! and L2).

B.Connect the neutral (white) line to the center of the

terminal block (marked N).

7.Attach ground wire of power cord with the green ground

screw (hole above strain relief bracket). Tighten all

terminal block screws (:3)securely.

8. Properly secure power cord to strain relief.

9. Reinstall the cover.

JLWf_KI_Iil_I_: NEVER LEAVE THE

COVER OFF OF THE TERMINAL BLOCK.

EXHAUST INFORMATION

WARNING - IN CANADAANDIN

THE UNITED STATES, THE REQUIRED EXHAUST

DUCT DIAMETER IS 4 IN (102ram). DO NOT

USE DUCT LONGER THAN SPECIFIED IN THE

EXHAUST LENGTH TABLE.

Using exhaust longer than specified length will:

, Increase the drying times and the energy cost.

, Reduce the dryer life.

, Accumulate lint, creating a potential fire hazard.

The correct exhaust installation isYOURRESPONSIBILITY.

Problems due to incorrect installation are not covered by

the warranty.

Removeand discard existing plastic or metal foil transition

duct and replace with ULlisted transition duct.

The MAXIMUM ALLOWABLEduct length and number of

bends of the exhaust system depends upon the type of

duct, number of turns, the type of exhaust hood (wall cap),

and all conditions noted below. Themaximum duct length

for rigid metal duct isshown in the following table.

27" DRYER EXHAUST LENGTH

RECOMMENDEDMAXIMUMLENGTH

Exhaust Hood Types

Recommended

Use only for short

run installations

_'1DIA

.......

Rigid

Metal

56 Feet

48 Feet

40 Feet

32 Feet

No, of 90 ° Rigid

Elbows Metal

0 42 Feet

1 34 Feet

2 26 Feet

3 18 Feet

EXHAUST INFORMATION (cont.}

24" DRYER EXHAUST LENGTH

RECOMMENDED MAXIMUM LENGTH

Exhaust Hood Tgpes

Recommended

Use onlg for short

run installations

4" DIA

_'d I_ 2 1/2"

No. of 90 ° Rigid

Elbows Metal

0 /43 Feet 36 Feet

i 33 Feet 26 Feet

2 24 Feet 16 Feet

, For every additional 90° elbow, reduce the allowable vent

systemlength by 10ft.

, Two 45°elbows will betreated likeone 90°elbow. Forthe side

exhaust installations,add one 90°elbow to the chart.

, Thetotal vent system length includes allthe straight portions

and elbows of the system (transition duct included).

EXHAUST SYSTEM CHECK LIST

HOOD ORWALL CAP

, Terminate in a manner to prevent back drafts or entry of

birds or other wildlife.

, Termination should present minimal resistance to

the exhaust air fiow and should require little or no

maintenance to prevent clogging.

,Never install a screen in or over the exhaust duct. This

could cause lint build up.

, Wall caps must be installed at least 12 in. above ground

level or any other obstruction with the opening pointed

down.

SEPARATIONOFTURNS

For best performance, separate all turns by at least 4 ft.

of straight duct, including distance between last turn and

exhaust hood.

TURNSOTHERTHAN 90°

* One turn of 45oor less may be ignored.

* Two 45oturns should be treated as one 90oturn.

* Eachturn over 45oshould be treated as one 90oturn.

SEALING OFJOINTS

. All joints should be tight to avoid leaks. The male end of

each section of duct must point away from the dryer.

* Donot assemble the ductwork with fasteners that extend

into the duct. They will serve as a collection point for lint.

, Duct joints can be made air and moisture-tight by

wrapping the overlapped joints with duct tape.

, Horizontal runs should slope down toward the outdoors

1/4 inch per foot

INSULATION

Duct work that runs through an unheated area or isnear air

conditioning should be insulated to reduce condensation

and lint build-up.

Installation

[] EXHAUST CONNECTION

, WARNING - TO REDUCE THE

RISK OF FIRE OR PERSONAL INJURY:

. This appliance must be exhausted to the outdoors.

. Use only 4" rigid metal ducting for the home exhaust

duct.

, Use only 4" rigid metal or UL-listed flexible metal

(semi-rigid or foil-type) duct to connect the dryer to the

home exhaust duct. It must be installed in accordance

with the instructions found in "Connecting The Dryer

To House Vent" on page 8 of this manual.

. Donot terminate exhaust in a chimney, a wall, a ceiling,

gas vent, crawl space, attic, under an enclosed floor,

or in any other concealed space of a building. The

accumulated lint could create a potential fire hazard.

, Never terminate the exhaust into a common duct with

a kitchen exhaust system. A combination of grease

and lint creates a potential fire hazard.

, Do not use duct longer than specified in the exhaust

length table. Longer ducts can accumulate lint,

creating a potential fire hazard.

, Never install a screen in or over the exhaust duct. This

will cause lint to accumulate, creating a potential fire

hazard.

, Do not assemble ductwork with any fasteners that

extend into the duct. These fasteners can accumulate

lint, creating a potential fire hazard.

, Do not obstruct incoming or exhausted air.

, Provideanaccessfor inspectionandcleaningoftheexhaust

system,especiallyat turns andjoints. Exhaustsystemshall

be inspectedand cleanedat leastonceayear.

THIS DRYER COMES READY FOR REAR

EXHAUSTING. IF SPACE IS LIMITED, USE

THE INSTRUCTIONS IN SECTION 6 TO

EXHAUST DIRECTLY FROM THE SIDES OR

BOTTOM OF THE CABINET.

STANDARD REAR EXHAUST

Forstraight lineinstallation,connect

the drger exhaustto theexternal

exhausthood usingduct tape or

clamp.

EXTERNALDUCT

OPENING

DUCTTAPEOR

DUCTCLAMP

4" METAL DUCTCUT

TO PROPERLENGTH

DUCTTAPEOR

DUCTCLAMP

®

°°i ©© O

nstructions

STANDARD REAR EXHAUST

(Vented above floor level}

AGE

NOTE: ELBOWS WILL PREVENT DUCT KINKING AND COLLAPSING

ELBOW HIGHLY

RECOMMENDED

[5]LEVELINGAND STABILIZINGYOURAPPLIANCE

FRONT-TO-BACK,

[t¢l

2LEVELINGLEGS

Level and stabilizing your appliance

!. Carefully move the appliance to its final location. Gently rock

the appliance into position. It isimportant not to damage the

rubber leveling legswhen moving your appliance to its final

location. Damaged legs can increase appliance vibration. It

may be helpful to spray window cleaner on the floor to help

move your appliance to its final position.

Note: Do not use washer cover to lift the unit.

2.To ensure the appliance is level and solid on all four legs,

tilt the appliance forward so the rear legs are off the

ground. Gently set the appliance back down to allow the

rear legs to self adjust.

3.With the appliance in its final position, place a level on top

of back part of the washer lid and check it side to side,

then check front to back. Screw the front leveling legs up

or down to ensure the appliance is resting solid on all four

legs (no rocking or the appliance should exist), turn the

lock nuts on each leg up toward the base of the unit and

snug with a wrench.

Note: Keepthe leg extension at minimum to prevent excessive

vibration. Thefarther out legs are extended, the more the unit

will vibrate.

7

Installation instructions

CONNECTING THE DRYERTO HOUSEVENT

RIGIDMETALTRANSITIONDUCT

• Forbest drying performance, a rigid metal transition duct is

recommended.

• Rigidmetal transitions ducts reduce the risk of crushing and

kinking.

UL-LISTEDFLEXIBLEMETAL(SEMI-RIGID}TRANSITIONDUCT

• If rigid metal duct cannot be used,then UL-listedflexible metal

(semi-rigid)ducting can beused(KitWX08X10077).

• Neverinstallflexiblemetal duct in walls,ceilings,floors or other

enclosedspaces.

• Total length of flexible metal duct should not exceed 8 feet

(2.4m).

• Formanyapplications,installingelbows at both the dryerand

the wall ishighlyrecommended(seeillustrations).Elbowsallow

the appliance to sit closeto the wall without kinking and or

crushingthe transitionduct, maximizingdryingperformance.

•Avoidrestingtheduct onsharpobjects.

UL-LISTEDFLEXIBLEMETAL(FOIL-TYPE}TRANSITIONDUCT

• In special installations,it may be necessaryto connect the

dryerto the housevent usinga flexible metal (foil-type)duct.

A UL-listedflexible metal (foil-type)ductmay be usedONLYin

installations where rigid metal or flexible metal (semi-rigid)

ducting cannot be used AND where a 4" diameter can be

maintainedthroughout theentirelengthof thetransitionduct.

• InCanadaandtheUnitedStates,onlytheflexiblemetal(foil-type)

ductsthat complywith the"Outlinefor ClothesDryerTransition

DuctSubject2158A"shallbeused.

• Neverinstallflexiblemetal duct in walls,ceilings,floors or other

enclosedspaces.

• Total length of flexible metal duct should not exceed 8 feet

(2.4m).

•Avoidrestingtheduct onsharpobjects.

• Forbest dryingperformance:

1.Slideoneend ofthe duct overthe clothesdryeroutlet pipe.

2.Securetheduct with a clamp.

3.With the dryer in its permanent position,extendthe duct to

its full length.Allow 2" of duct to overlapthe exhaustpipe.

Cutoff and removeexcessduct. Keepthe duct asstraightas

possiblefor maximum airflow.

4.Securetheduct to the exhaustpipewith theother clamp.

DO

ELBOW HIGHLY

RECOMMENDED

;2

DO NOT USE

EXCESSIVE

DON'T

EXHAUST

8

Installation instructions

_-124" MODELS ONLY:

DRYER EXHAUST TO RIGHT, LEFT OR

BOTTOM CABINET

_WARNING - BEFOREPERFORMING

THIS EXHAUST INSTALLATION, BE SURE

TO DISCONNECT THE APPLIANCE FROM

ITS ELECTRICAL SUPPLY. PROTECT YOUR

HANDS AND ARMS FROM SHARP EDGES

WHEN WORKING INSIDE THE CABINET. BE

SURE TO WEAR GLOVES.

For downward venting, rotate elbow

sections so that elbow points downward

REMOVE

DESIRED

KNOCKOUT

(ONLY1)

ADDING ELBOW AND DUCT FOR

EXHAUST TO LEFT OR RIGHT SIDE OF

CABINET

, Rotate elbow sections so that the opening points to the

sideto which you want to vent. Preassemble 4"elbow with

4" duct. Use only 4" UL approved rigid metal for ducting

inside the dryer.

, Connect duct assembly to the internal elbow.

WARNING- Sesurenottopullordamagethe

electrical wires inside the dryer when inserting the duct,

4" UL approved rigid metal

i DUCT

........ i..[j ...... TAPE

, Apply duct tape as shown on the joint between the dryer

internal duct and the straight duct pipe.

AWARNING-

Internal duct joints must be

_ ecured with tope, otherwise

they may separate and cause

a safety hazard.

27" MODELS ONLY:

DRYER EXHAUST TO RIGHT, LEFT OR

BOTTOM CABINET

THIS EXHAUST INSTALLATION, BE SURE

TO DISCONNECT THE APPLIANCE FROM

ITS ELECTRICAL SUPPLY. PROTECT YOUR

HANDS AND ARMS FROM SHARP EDGES

WHEN WORKING INSIDE THE CABINET. BE

SURE TO WEAR GLOVES.

For downward venting, rotate elbow

sections so_

EXHAUST TO LEFT OR RIGHT SIDE OF

CABINET

, Rotate elbow sections so that the opening points to the

sideto which you want to vent. Preassemble 4" elbow with

4" duct. Use only 4" UL approved rigid metal for ducting

inside the dryer.

* Connect duct assembly to the internal elbow.

,_ WARNING- Besure not to pull or damage the

electrical wires inside the dryer when inserting the duct.

, Apply duct tape as shown on the joint between the dryer

internal duct and the straight duct pipe.

AWARNING-

H Internal duct joints must be

secured with tope, otherwise

they may separate and cause

a safety hazard.

Installation

If]PLUMBING INFORMATION

WATER SUPPLY REQUIREMENTS

. HOTAND COLDWATERFAUCETS- Must bewithin 42" of

the appliance water inlet hose connections. The faucets

must be 3/4" garden hose-type so inlet hoses can be

connected.

. WATERPRESSURE- Must be between !0 and 120 pounds

per square inch with a maximum unbalance pressure,

hot vs.cold flowing, of !0 pounds per square inch.

. WATERTEMPERATURE- Water heater should be set to

deliver !20°F (50°C) in the washer when HOT wash is

selected.

, SHUT-OFFVALVES- Both hot and cold water shut-off

valves (faucets) should be supplied.

. LOCATION- Do not install appliance in an area where the

temperature will fall below freezing. If appliance isstored

or transported in freezing temperatures, be sure all water

from the fill and drain systems has been removed.

DRAIN REQUIREMENTS

. DRAIN RATE- The drain or standpipe must be capable

of accepting a discharge at the rate of 16 gallons per

minute.

, DRAINHEIGHT- The drain height must be 33" minimum

and 96" maximum.

. STANDPIPEDIAMETER- The standpipe diameter must

be 1-1/2" minimum. There MUSTbe an air gap around

the drain hose in the standpipe. A snug fit can cause a

siphoning action.

, SIPHONBREAKKIT- Fora drain facility lessthan 33" high,

the hose, coupling and clamps provided in the machine

must be used and, in addition, a siphon break MUSTbe

installed on the back of the machine. Use Siphon Break

Kit WH49X228 and follow instructions in the kit.

Instructions

[8-1CONNECTING TO PLUMBING FACILITIES

Ifnot installed,install rubberwasher in oneendof hotwater hose.

Thread hot water hose onto connection labeled H at top rear

of washer. Handtighten, plus an additional 1/8 turn with pliers.

If not installed, install rubber washer in one end of cold water

hose.Threadcold water hoseonto connection labeled Cat top

rear of washer. Hand tighten, plus an additional 1/8 turn with

pliers.

Moveapplianceasclosetofinal location aspossible,leavingroom

for you to make water, drain, electrical and vent connections to

your home.

NOTE: If longer drain hose

is required, order drain hose

extension kit, part number

WH49X301.Connect additional

drain hose (contained in kit)to

original hose with hose clamp

(contained in kit).

Insertfreeendof drain hoseinto

drain opening of your home up

to drain hose stopper (do not

removehosestopper itprevents

siphoning). If water valves and

drain are built into wall, fasten

drain hose to one of water

hoses with cable tie provided

(ribbed side on inside). If your

drain isa standpipe,fastendrain

hoseto standpipe with cabletie

provided.

10

Installation instructions

[_]MOBILE OR MANUFACTURED HOME

INSTALLATION

. Installation MUSTconform to the MANUFACTUREDHOME

CONSTRUCTION& SAFETYSTANDARD,TITLE 24, PART

32-80 or, when such standard is not applicable, with

AMERICAN NATIONAL STANDARD FOR MOBILE HOME,

ANSl/NFPA NO. 501B.

. The appliance MUST be vented to the outdoors with

the termination securely fastened to the mobile home

structure,

. The vent MUST NOT be terminated beneath a mobile or

manufactured home.

. The vent duct material MUSTBEMETAL.

• KIT14-D346-33MUSTbeusedto attach theappliancesecurely

to the structure.

• Thevent MUSTNOTbe connectedto any other duct, vent, or

chimney.

. Do not use sheet metal screws or other fastening devices

which extend into the interior of the exhaust vent.

. See section 2 for electrical connection information.

[i-0-IALCOVE OR CLOSET INSTALLATION

. If your appliance is approved for installation in an alcove

or closet, it will be stated on a label on the appliance

back.

. TO PREVENTLARGEAMOUNTSOFLINTAND MOISTURE

FROMACCUMULATINGANDTO MAINTAINDRYING

EFFICIENCY,THISMACHINEMUSTBEEXHAUSTED

OUTDOORS.

. Do not install this appliance with lessthan the minimum

clearances shown above.

CONSIDERATION MUST BE GIVEN TO PROVIDE

ADEQUATE CLEARANCES FOR INSTALLATION AND

SERVICE.

AWARNING: DoNOTINSTALLTHIS

APPLIANCEIN A CLOSETWITH A SOLID DOOR.

DOOR VENTILATION OPENING (27" MODELS)

A minimum of 120 square inches of opening, equally divided

at top and bottom, is required. Air openings are required to

be unobstructed when a door is installed. A Iouvered door

with equivalent air openings for the full length of the door

isacceptable.

When louvers or registers are placed in door openings, the

free air openings of the louvers or registers must equal 120

square inches.

DOOR VENTILATION OPENING (24" MODELS)

27" Model

I Sq.In.

/_0 /

li: Iit qn

A minimum of 72 square inches of opening is required. Air

openings are required to be unobstructed when a door is

installed. A Iouvered door with equivalent air openings for

the full length of the door is acceptable.

When louvers or registers are placed in door openings, the

free air openings of the louvers or registers must equal 72

square inches.

24,,Model__ Sqln

/Ill ', _Sq .In.

[n7BATHROOM OR BEDROOM INSTALLATION

. The appliance MUST be vented to the outdoors. See

EXHAUSTINFORMATION section 3 & 4.

, The installation must conform with local codes or, in the

absence of local codes, with the NATIONAL ELECTRICAL

CODE,ANSI/NFPA NO. 70.

11

Installation instructions

[] SERVICING

,WARNING- LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING

CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION

AFTER SERVICING/INSTALLATION.

Forreplacement parts and other information, refer to Owner's Manual for servicing phone numbers.

REGISTERYOUR NEW APPLIANCE TO RECEIVEANY

IIvlPORTANTPRODUCT NOTIFICATIONS.

Please go to www.GEAppliances.com or mail in your

Product Registration Card.

Forquestions on installation, call: 800.626.2000 (US)or

800-56!-3344 (Canada).

12

Page is loading ...

Instructions d'Installation

iT21REPARATION

AVERTISSEMENT- HARQUEZ TOUS LES FILS AVANT LE DEBRANCHEMENT

LORSQUE VOUS EFFECTUEZ UN CONTROLE POUR REPARATION. LES ERREURS DE

BRANCHEMENT PEUVENT CAUSEES DES PROBLEMES DE FONCTIONEMENT APRES

REPARATION ET D'INSTALLATION.

Pour les pisces de rechc]nge et (]utres informc]tions, veuillez reporter (]u Manuel de I'Utilisc]teur pour les num#ros de

t#l#phone du service c]pr_svente.

ENREGISTREZVOTRE NOUVEL APPAREIL POUR OUE

VOUS RECEVIEZDES INFORiVlATIONSIIPORTANTES

SUR LE PRODUIT.

Allez, SVP,sur notre site www.GEAppliances.com ou

envoyez par la poste votre Carte d'inscription du produit

Pour des questions sur I'instc]llc]tion,composez:

800.626.2000 (E.U.)ou 800.56!.334/4 (Cc_nodo)

12

Page is loading ...

Kenmore GTUP240EM4WW Installation guide

Kenmore GTUP240EM4WW Installation guide

in other languages

Related papers

Other documents