Kramer Electronics VS-88DTP User manual

Brand: Kramer Electronics

Model: VS-88DTP

Category: Video switches

Type: User manual

KRAMER ELECTRONICS LTD.

USER MANUAL

MODEL:

VS-88DTP

8x8

DVI - Twisted Pair Matrix

Switcher

P/N: 2900-000749 Rev 2

VS-88DTP – Contents i

Contents

1 Introduction 1

2 Getting Started 2

2.1 Achieving the Best Performance 2

2.2 Safety Instructions 2

2.3 Recycling Kramer Products 3

3 Overview 4

3.1 Defining the VS-88DTP 8x8 DVI - Twisted Pair Matrix Switcher 5

3.2 Using the IR Transmitter 8

4 Installing the VS-88DTP in a Rack 9

5 Connecting the VS-88DTP 10

5.1 Connecting to the VS-88DTP via RS-232 11

5.2 Connecting a PC or Controller to the RS-485 Port 12

5.3 Connecting the VS-88DTP via Ethernet 15

6 Operating the VS-88DTP 18

6.1 Routing Inputs to Outputs 18

6.2 Disconnecting Outputs 18

6.3 Storing and Recalling Setups in Presets 19

6.4 Switching Between Protocol 2000 and Protocol 3000 19

6.5 Acquiring the EDID 20

6.6 Locking and Unlocking the Front Panel Buttons 22

6.7 Control Configuration via the Ethernet Port 22

7 Controlling the VS-88DTP Remotely via Ethernet 23

7.1 Connecting to the VS-88DTP via your Browser 23

7.2 The Main Switching Matrix Page 26

7.3 The Configuration Page 31

8 Technical Specifications 33

9 Default Communication Parameters 34

10 Default EDID 35

11 Updating the VS-88DTP Firmware 37

12 Table of ASCII Codes for Serial Communication (Protocol 3000) 38

13 Hex Codes for Serial Communication (Protocol 2000) 39

14 Kramer Protocol 40

14.1 Switching Protocols 40

14.2 Kramer Protocol 3000 40

14.3 Kramer Protocol 2000 47

ii VS-88DTP - Introduction

Figures

Figure 1: VS-88DTP 8x8 DVI - Twisted Pair Matrix Switcher Front Panel 6

Figure 2: VS-88DTP 8x8 DVI - Twisted Pair Matrix Switcher Rear Panel

Figure 3: Connecting the VS-88DTP 8x8 DVI - Twisted Pair Matrix Switcher

Figure 4: RS-485 DIP-switches

Figure 5: RS-485 Termination DIP-switch

Figure 6: Control of Multiple VS-88DTP Devices via RS-232 and RS-485

Figure 7: Local Area Connection Properties Window

Figure 8: Internet Protocol (TCP/IP) Properties Window

Figure 9: Preset Number Assignments using the Selector Buttons

Figure 10: Java Test Page Success Message

Figure 11: Entering the IP Number in the Address Bar

Figure 12: The Loading Page

Figure 13: First Time Security Warning

Figure 14: Main Switching Matrix Page

Figure 15: Selecting a Switching Point on the Matrix

Figure 16: Switching in the Offline Mode

Figure 17: Selecting Preset 07

Figure 18: Selecting Preset 03

Figure 19: Recalling a Preset in Offline Mode

Figure 20: Configuration Page

VS-88DTP - Introduction 1

1 Introduction

Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been

providing a world of unique, creative, and affordable solutions to the vast range of

problems that confront the video, audio, presentation, and broadcasting

professional on a daily basis. In recent years, we have redesigned and upgraded

most of our line, making the best even better!

Our 1,000-plus different models now appear in 11 groups that are clearly defined

by function: GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Routers;

GROUP 3: Control Systems; GROUP 4: Format/Standards Converters; GROUP 5:

Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7:

Scan Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9:

Room Connectivity; GROUP 10: Accessories and Rack Adapters and GROUP 11:

Sierra Products.

Congratulations on purchasing your Kramer VS-88DTP 8x8 DVI - Twisted Pair

Matrix Switcher, which is ideal for the following typical applications:

• Conference room presentations

• Advertising

• Rental and staging

2 VS-88DTP - Getting Started

2 Getting Started

We recommend that you:

• Unpack the equipment carefully and save the original box and packaging

materials for possible future shipment

• Review the contents of this user manual

• Use Kramer high performance high resolution cables

Go to http://www.kramerelectronics.com to check for up-to-date

user manuals, application programs, and to check if firmware

upgrades are available (where appropriate).

2.1 Achieving the Best Performance

To achieve the best performance:

• Use only good quality connection cables to avoid interference, deterioration

in signal quality due to poor matching, and elevated noise levels (often

associated with low quality cables)

• Do not secure the cables in tight bundles or roll the slack into tight coils

• Avoid interference from neighboring electrical appliances that may adversely

influence signal quality

• Position your Kramer VS-88DTP away from moisture, excessive sunlight and

dust

2.2 Safety Instructions

Caution: There are no operator-serviceable parts inside the unit

Warning:

You use only the power cord that is supplied with the

unit. Do not open the unit. High voltages can cause

electrical shock! Servicing by qualified personnel only.

Warning:

Disconnect the power and unplug the unit from the wall

before installing

VS-88DTP - Getting Started 3

2.3 Recycling Kramer Products

The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC

aims to reduce the amount of WEEE sent for disposal to landfill or incineration by

requiring it to be collected and recycled. To comply with the WEEE Directive,

Kramer Electronics has made arrangements with the European Advanced

Recycling Network (EARN) and will cover any costs of treatment, recycling and

recovery of waste Kramer Electronics branded equipment on arrival at the EARN

facility. For details of Kramer’s recycling arrangements in your particular country

go to our recycling pages at

http://www.kramerelectronics.com/support/recycling/.

4 VS-88DTP - Overview

3 Overview

The VS−88DTP is a high−performance matrix switcher for DVI signals. The unit

accepts up to eight DVI inputs, reclocks and equalizes the signals, and routes to

any or all DGKat™ twisted pair outputs simultaneously for connection to

compatible TP receivers, for example, the PT-572HDCP+ or TP-574.

More specifically, the VS-88DTP features:

• A maximum data rate of 4.95Gbps (1.65Gbps per graphic channel)

• 8 DVI-D inputs on DVI-I connectors

• 8 DGKat twisted pair outputs on RJ-45 connectors

• HDTV compatibility (no HDCP compliance)

• DGKat™ Signal Integration that converts TMDS as well as control and

communication to signals that run over twisted pair cables. Kramer strongly

recommends using Kramer DGKat™ cables designed specifically for

optimum performance

• Kramer Equalization & re-Klocking™ Technology that rebuilds the digital

signal integrity to travel longer distances

• I-EDIDPro™ Kramer Intelligent EDID Processing™, an intelligent EDID

handling & processing algorithm that ensures Plug and Play operation for

DVI systems

• A system range of up to 30m (98ft) at 1080p on shielded BC-DGKat524

cable; up to 70m (230ft) at 1080p on shielded BC-DGKat623 cable; up to

90m (295ft) at 1080p on shielded BC-DGKat7a23 cable

• Flexible control options including: front panel, IR remote (included), RS-232

(K-Router™ Windows®-based software is included), RS-485, Ethernet

(Windows®-based Ethernet Configuration Manager & Virtual Serial Port

Manager included)

• Output disconnect for each output

• Front panel lockout to prevent tampering with the front panel buttons

• 16 memory locations that store multiple switches as presets to be recalled

and executed when needed

VS-88DTP - Overview 5

• A worldwide power supply of 100-240V AC

• A standard 19” rack mount size of 1U with included rack “ears”

Note: The VS-88DTP requires STP (shielded twisted pair) cable. For optimum

range and performance, use Kramer's BC-DGKat524, BC-DGKat623 or

BC-DGKat7a23 cables. The transmission range depends on the signal resolution,

graphics card and display used. The distance using non-Kramer CAT 5, CAT 6,

and CAT 7 cables may not reach these ranges. Use only shielded cable where

both ends of the shield are soldered to ground.

3.1 Defining the VS-88DTP 8x8 DVI - Twisted Pair Matrix

Switcher

This section defines the VS-88DTP.

VS-88DTP - Overview

Figure 1: VS-88DTP 8x8 DVI - Twisted Pair Matrix Switcher Front Panel

# Feature Function

1 IR LED Lights yellow when receiving a signal from an IR remote control

2 IR Sensor IR remote control signal receiver

3 POWER LED Lights green when the device is powered on

4 ALL Button Press to select all outputs (see Section 6.1

)

OFF Button Press to disconnect one or all outputs (see Section 6.2

)

SELECT IN Buttons Press to select an input (1 to 8) following the selection of an output

7 SELECT OUT Buttons Press to select an output (1 to 8) followed by the selection of an input

8 STO Button Press to store a matrix configuration

9 RCL Button Press to recall a matrix configuration

10 LOCK Button Press and hold to toggle locking and unlocking the front panel buttons (see Section 7.2.4

)

EDID Button Press to acquire the EDID (see Section 6.5

) (lights when configuring the EDID)

OUTPUT Numbers Indicates the relevant output to which an input (1 to 8, shown on the 7-segment display) is currently switched

13 7-segment Display Displays the selected video input switched to the output (marked above each input)

6 VS-88DTP – Overview

VS-88DTP - Overview

VS-88DTP – Overview 7

Figure 2: VS-88DTP 8x8 DVI - Twisted Pair Matrix Switcher Rear Panel

Feature

Function

14 IN 1 to IN 8 DVI Input Connectors Connect to the DVI sources

15 OUT 1 to OUT 8 RJ-45 TP Output

Connectors

Connect to the TP receivers (for example, PT-572HDCP+ and TP-574)

16 RS-232 9-pin D-sub (F) Connect to a PC or other serial remote controller

17 PROG TERM 2-way DIP-switch DIP-switch 1 Sets the RS-485 bus termination (see Section 5.2.2

DIP-switch 2 Sets the Programming mode. Only for the use of Kramer service personnel. Default = Off

) Up = Off, Down = On. Default = On

18 RS-485 3-pin Terminal Block

Connect to a serial controller or to another VS-88DTP unit.

Connect G to Ground, B to B, and A to A (see

Section 5.2

)

ETHERNET RJ-45 TP Connector Connect to a PC or LAN for remote control

20 REMOTE IR 3.5mm Mini Jack Connect to an external IR receiver unit for controlling the device via an IR remote controller (instead of

using the front panel IR receiver)

21 MACH # DIP-Switch Sets the RS-485 bus machine number (see Section 5.2.1

)

RESET Button Press the reset button while turning the device on in order to reset the Ethernet factory default

definitions (see

Section 9

)

AC Power Receptacle Connect to the AC mains power supply

24 AC Mains Fuse AC mains supply protection fuse

25 AC Mains Power Switch Turns the AC mains power supply to the device on and off

8 VS-88DTP - Overview

3.2 Using the IR Transmitter

You can use the RC-IR3 IR transmitter to control the machine via the built-in IR

receiver on the front panel or, instead, via an optional external IR receiver (Model:

C-A35M/IRR-50). The external IR receiver can be located up to 15 meters away

from the machine. This distance can be extended to up to 60 meters when used

with three extension cables (Model: C-A35M/A35F-50).

Before using the external IR receiver, be sure to arrange for your Kramer dealer to

insert the internal IR connection cable (P/N: 505-70434010-S) with the 3.5mm

connector that fits into the REMOTE IR opening on the rear panel. Connect the

external IR receiver to the REMOTE IR 3.5mm connector.

VS-88DTP - Installing the VS-88DTP in a Rack 9

4 Installing the VS-88DTP in a Rack

This section provides instructions for rack mounting the unit.

10 VS-88DTP - Connecting the VS-88DTP

5 Connecting the VS-88DTP

Always switch off the power to each device before connecting it to your

VS-88DTP. After connecting your VS-88DTP, connect its power and

then switch on the power to each device.

To connect the VS-88DTP as illustrated in the example in

Figure 3:

1. Connect up to eight DVI sources (for example, computer graphics sources)

to the IN 1 to IN 8 DVI connectors.

You do not have to connect all the sources.

2. Connect the OUT 1 to OUT 8 TP connectors to up to eight TP receivers (for

example, the PT-572HDCP+ and TP-574).

You do not have to connect all the outputs.

3. If required, connect a controller to the RS-232 (see Section 5.1) and/or

Ethernet port (see Section

5.3

4. Connect the power cord (not shown in

Figure 3).

5. If required, acquire the EDID (see

Section 6.5

VS-88DTP - Connecting the VS-88DTP 11

Figure 3: Connecting the VS-88DTP 8x8 DVI - Twisted Pair Matrix Switcher

5.1 Connecting to the VS-88DTP via RS-232

You can connect to the VS-88DTP via an RS-232 connection using, for example, a

PC. Note that a null-modem adapter/connection is not required.

To connect to the VS-88DTP via RS-232:

• Connect the RS-232 9-pin D-sub rear panel port on the VS-88DTP unit via a

9-wire straight cable (only pin 2 to pin 2, pin 3 to pin 3, and pin 5 to pin 5

need to be connected) to the RS-232 9-pin D-sub port on your PC

12 VS-88DTP - Connecting the VS-88DTP

5.2 Connecting a PC or Controller to the RS-485 Port

You can operate the VS-88DTP via the RS-485 port from a distance of up to

1200m (3900ft) using any device equipped with an RS-485 port (for example, a

PC). For successful communication, you must set the RS-485 machine number

and bus termination.

To connect a device with a RS-485 port to the VS-88DTP:

• Connect the A (+) pin on the RS-485 port of the PC to the A (+) pin on the

RS-485 port on the rear panel of the VS-88DTP

• Connect the B (–) pin on the RS-485 port of the PC to the B (–) pin on the

RS-485 port on the rear panel of the VS-88DTP

• Connect the G pin on the RS-485 port of the PC to the G pin on the RS-485

port on the rear panel of the VS-88DTP

5.2.1 Setting the RS-485 Machine Number

When several VS-88DTP units are connected, the machine number determines

the unique identity of the VS-88DTP on the bus (see

Figure 6).

Note:

• When using a stand-alone VS-88DTP unit, set the machine number to 1

(factory default)

• When connecting more than one VS-88DTP, set the first machine

(connected via RS-232) to be machine number 1. The other

VS-88DTP units must each be set to a unique machine number between 2

and 16

The machine number on the VS-88DTP is set using the DIP-switches on the rear

panel.

To set the RS-485 machine number using the DIP-switches:

Figure 4 illustrates the factory default MACH # DIP-switch settings.

VS-88DTP - Connecting the VS-88DTP 13

Figure 4: RS-485 DIP-switches

DIP-switches 1, 2, 3 and 4 determine the RS-485 machine number of the

VS-88DTP.

Machine

Number

SW1 SW2 SW3 SW4

1 (Default) OFF OFF OFF OFF

2 OFF OFF OFF ON

3 OFF OFF ON OFF

4 OFF OFF ON ON

5 OFF ON OFF OFF

6 OFF ON OFF ON

7 OFF ON ON OFF

8 OFF ON ON ON

9 ON OFF OFF OFF

10 ON OFF OFF ON

11 ON OFF ON OFF

12 ON OFF ON ON

13 ON ON OFF OFF

14 ON ON OFF ON

15 ON ON ON OFF

16 ON ON ON ON

5.2.2 Setting the RS-485 Bus Termination

DIP-switch 1 sets the RS-485 bus termination of the VS-88DTP. Only the first and

last physical units on the RS-485 bus must be terminated, all others must be

unterminated. Moving the DIP-switch up turns the termination off (default), moving

the switch down enables the termination.

Figure 5 illustrates the factory default PROG TERM DIP-switch positions.

14 VS-88DTP - Connecting the VS-88DTP

Figure 5: RS-485 Termination DIP-switch

5.2.3 Connecting and Controlling Multiple VS-88DTP Devices

You can daisy-chain up to 16 VS-88DTP devices with operation via RS-232 from a

PC or serial controller (see

Figure 6).

To daisy-chain up to 16 VS-88DTP devices:

1. Connect the RS-232-1 port on the first VS-88DTP device to the PC (see

Section 5.1

Alternatively, the RS-485 port could be used for PC control.

2. Connect the RS-485 terminal block port on the first device to the RS-485

port on the second device, and so on for all devices. (Connect A to A, B to B,

and G to G.)

3. Set the machine number and termination as follows:

 The first device is machine number 1 and the subsequent seven

devices are machine numbers 2 to 16 (see

Section 5.2.1

 Terminate the first and last devices, that is, terminate machine

numbers 1 and 16. Ensure that all other devices are unterminated (see

)

Section 5.2.2)

VS-88DTP - Connecting the VS-88DTP 15

Figure 6: Control of Multiple VS-88DTP Devices via RS-232 and RS-485

5.3 Connecting the VS-88DTP via Ethernet

You can connect the VS-88DTP via Ethernet using a crossover cable (see Section

5.3.1

) for direct connection to the PC, or a straight-through cable (see Section

5.3.2

After connecting the Ethernet port, you have to install and configure your Ethernet Port. For

detailed instructions, see the Configuration Guide in the technical support section on our Web

site

) for connection via a network hub or network router.

http://www.kramerelectronics.com.

5.3.1 Connecting to the Ethernet Port Directly to a PC

You can connect the Ethernet port of the VS-88DTP to the Ethernet port on your

PC, via a crossover cable with RJ-45 connectors.

This type of connection is recommended for identifying the

VS-88DTP with the factory configured default IP address

After connecting the Ethernet port, configure your PC as follows:

1. Right-click the My Network Places icon on your desktop.

2. Select Properties.

3. Right-click Local Area Connection Properties.

16 VS-88DTP - Connecting the VS-88DTP

4. Select Properties.

The Local Area Connection Properties window appears.

5. Select the Internet Protocol (TCP/IP) and click the Properties Button (see

Figure 7).

Figure 7: Local Area Connection Properties Window

6. Select Use the following IP Address, and fill in the details as shown in

Figure 8.

7. Click OK.

Figure 8: Internet Protocol (TCP/IP) Properties Window

Page is loading ...

Kramer Electronics VS-88DTP User manual

Brand: Kramer Electronics

Model: VS-88DTP

Category: Video switches

Type: User manual

Download PDF

report

Kramer Electronics VS-88DTP User manual

Kramer Electronics VS-88DTP User manual

Related papers

Other documents