Bakers & Chefs 9905TB Owner's manual

Brand: Bakers & Chefs

Model: 9905TB

Category: Barbecues & grills

Type: Owner's manual

This manual is also suitable for

P4770A

NOTE TO INSTALLER:

LEAVE THESE INSTRUCTIONS WITH THE CONSUMER AFTER INSTALLATION.

NOTE TO CONSUMER: RETAIN FOR FUTURE REFERENCE.

THIS OUTDOOR COOKING GAS APPLIANCE IS NOT INTENDED TO BE

INSTALLED IN OR ON RECREATIONAL VEHICLES AND/OR BOATS.

READ THE FOLLOWING INSTRUCTIONS CAREFULLY AND BE SURE YOUR

GRILL IS PROPERLY INSTALLED, ASSEMBLED AND MAINTAINED. FAILURE

TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS BODILY

INJURY AND/OR PROPERTY DAMAGE. IF YOU HAVE QUESTIONS

CONCERNING ASSEMBLY OR OPERATION, CALL OUR SERVICE CENTER

AT 1-800-770-9769, MONDAY THROUGH FRIDAY 8:00 AM - 4:30 PM, CST.

ASSEMBLY & OPERATING INSTRUCTIONS

DATE: JUNE 24,1999

REVISED:

SAFETY INSTRUCTIONS

PARTS LIST

ASSEMBLY INSTRUCTIONS

LIGHTING & OPERATING INSTRUCTIONS

CLEANING & MAINTENANCE INSTRUCTIONS

FREQUENTLY ASKED QUESTIONS

INTRODUCTION TO COOKING METHODS

BAKERS & CHEFS RECIPES

TABLE OF CONTENTS

PAGE

MODEL

9905TB

LPG

Safety Instructions

Read carefully before assembling and operating your Gas Grill.

INSTALLATION

This gas grill must be installed in accordance with the

local codes or, if in an area without local codes, with

the latest edition of the National Fuel Gas Code ANSI

Z223.1. In Canada, installation must conform to the

standard CAN/CGA 1-b149.1 and/or .2 (Installation

Code for Gas Burning Appliances and Equipment) and

any local codes.

THE LOCATION FOR YOUR GRILL

DO NOT use your gas grill in garages, porches,

breezeways, sheds or other enclosed areas. Your gas

grill is to be used OUTDOORS ONLY, at least 21" from

the back and side to any combustible surface. The

grill should not be placed under any surface that will

burn. Do not obstruct the flow of combustion and

ventilation air around the grill housing.

This outdoor cooking gas appliance is not intended to be

installed in or on recreational vehicles and/or boats.

PROTECT YOUR CHILDREN: Keep them away

from a hot grill during and after cooking. Do not allow

children to play near or operate grill.

CHECKING FOR GAS LEAKS

NEVER TEST FOR LEAKS WITH A FLAME

Prior to first use and at the beginning of each new

season (or whenever LP gas cylinder is changed),

you must check for gas leaks. Follow these steps:

Make soap solution by mixing one part liquid

detergent and one part water.

Turn off heat control valve(s), then turn on gas at

source.

Apply the soap solution to all gas connections.

Bubbles will appear in the soap solution if connec-

tions are not properly sealed. Tighten or repair

as necessary.

If you have a gas leak that you cannot repair, turn

off the gas at the source, disconnect fuel line from

grill and immediately call your grill dealer or gas

supplier for professional assistance.

LP GAS CYLINDER SAFETY

Your gas grill is designed for use with a standard 20

lb. LP gas cylinder (not included). DO NOT CONNECT

YOUR GRILL TO AN LP GAS CYLINDER EXCEEDING

THIS CAPACITY. A tank of approximately 12 inches

in diameter by 18-1/2 inches high should be the

Maximum size tank used. We recommend buying an

"OPD" gas cylinder - which offers an Overfilling

Prevention Device. This safety feature prevents the

tank from being accidentally overfilled which can cause

malfunction with your cylinder, regulator and/or grill.

Also be sure that (1) the cylinder is provided with a

shutoff valve terminating in an LP gas supply cylinder

valve outlet compatible with a Type I cylinder con-

nection device and a safety relief device having a

direct communication with the vapor space of the

cylinder; (2) the cylinder supply system must be

arranged for vapor withdrawal; and (3) the cylinder

used must include a collar to protect the cylinder valve.

The LP gas cylinder must be constructed and marked

in accordance with specifications of the U.S. Depart-

ment of Transportation (DOT). In Canada, gas

cylinders must meet Canadian Transportation and

Communications(CTC) specifications.

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, immediately call

your gas supplier or your fire

department.

FOR YOUR SAFETY

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

(a) Do not store (empty or full) spare gas

cylinders under or near this or any other

appliance.

(b) Never fill the cylinder beyond 80 percent

full.

If the information in "(a)" and "(b)" is not

followed exactly, a fire causing death or

serious injury may occur.

Keep the gas fuel hose away from hot grill

surfaces and dripping grease. Avoid unnec-

essary twisting of hose. Visually Inspect

hose prior to each use for cuts, cracks,

excessive wear or other damage.

If damaged - do not use the grill. Contact

your dealer for a factory authorized replace-

ment hose.

NEVER light grill with lid closed or before checking

to insure burner tubes are fully seated over gas

valve orifices.

NEVER lean over cooking surface while lighting

grill. Use barbecue tools with long wooden

handles and good quality insulated oven mitts

when operating grill.

PAGE 2

Safety Instructions

DANGER: If you smell or hear the hiss of

escaping gas from the LP gas cylinder:

Get away from the LP gas cylinder.

Do not attempt to correct the problem

yourself.

Call your fire department (Do not make the

call from near the LP gas cylinder - your

telephone is an electrical device).

Never connect an unregulated LP gas cylinder to

your grill. A gas regulator adjusted to have an outlet

pressure of 11" water column (W.C.) is supplied for

connection to the LP gas cylinder. The pressure

regulator and hose assembly supplied with the appli-

ance must be used. Replacement pressure regulators

and hose assemblies must be those specified by the

appliance manufacturer.

SAFETY !

BEWARE

SPIDERS

CAUTION: BURNER TUBES MUST BE IN-

SPECTED AND CLEANED BEFORE FIRST

USE

Spiders and small insects occasionally spin

webs or make nests in the burner tubes during

warehousing and transit. These webs can lead

to a gas flow obstruction which could result in

a fire in and around the burner tubes. This

type of fire is known as "FLASH-BACK" and

can cause serious damage to your grill and

create an unsafe operating condition for the

user. Although an obstructed burner tube is

not the only cause of "FLASH-BACK" it is the

most common cause and frequent inspection

and cleaning of the burner tubes is necessary.

Have the LP gas cylinder filled by a reputable LP gas

dealer, and visually inspected and re-qualified at each

filling.

Have your LP gas dealer check the release valve after

every filling to assure that it remains free of defects.

Always keep cylinder in an upright position. Always

close the cylinder valve when the grill is not in use.

Do not subject LP gas cylinder to excessive heat.

Never store your LP gas cylinder indoors. If you store

your grill indoors, ALWAYS disconnect LP gas

cylinder FIRST, and store LP gas cylinder safely

outside.

When the appliance is not in use, the gas must

be turned off at the supply cylinder.

Storage of an appliance indoors is permissible only

if the cylinder is disconnected and removed from the

appliance.

Cylinders must be stored outdoors in a well-ventilated

area out of the reach of children. Disconnected

cylinders must not be stored in a building, garage or

any other enclosed area.

HOSE ASSEMBLY SAFETY

Check tank valve features to ensure it has proper

external mating threads. (Type 1 connection per 10-

94 AGA Requirement)

Make sure all burner valves are in their off position.

Inspect valve connections port and regulator assem-

bly. Look for any damage or debris. Remove any

debris. Inspect hose for damage. Never attempt to

use damaged or plugged equipment. See your local

LP gas dealer for repair.

When connecting regulator assembly to the tank

valve, hand tighten nut clockwise to a positive stop. Do

Not use a wrench to tighten. Use of a wrench may

damage quick coupling nut and result in a hazardous

condition.

Open tank valve fully (counter-clockwise). Use a

soapy water solution to check all connections for

leaks before attempting to light grill. If a leak is found,

turn tank valve off and do not use grill untill repairs can

be made by a local LP gas dealer.

a) Turn the burner valve off.

b) Turn the tank valve off fully.( Turn clockwise to stop.)

c) Detach the regulator assembly from tank valve by

turning the quick coupling nut counter-clockwise.

To disconnect LP gas cylinder:

The hose assembly must be inspected before each use of

the appliance. If it is evident there is excessive abrasion

or wear; or the hose is cut, it must be replaced prior to the

appliance being put into operation.

TO CONNECT THE LP GAS SUPPLY CYLINDER,

PLEASE FOLLOW THESE STEPS:

Make sure tank valve is in its full off position. (Turn

clockwise to stop)

PAGE 3

Safety Instructions

BURNER TUBE CLEANING

For cleaning the burner tubes. Follow the procedure

that is most convenient for you.

Remove burner assembly from the grill bowl.

Bend a stiff wire, (a light weight coat hanger works

well) into a small hook as shown below,

Run the hook up through each venturi tube and

into the burner several times.

Run the brush up through each venturi tube and

into the burner several times.

SAFETY !

Use a bottle brush with a flexible handle.

VERY IMPORTANT:

The location of burner with respect to orifice is vital for safe operation. Check to assure the valve

orifices are inside of the burner tubes before using your gas grill. See drawing below.

If the burner tubes (venturi) do not fit over the valve orifices, lighting the burners may cause explosion

and/or fire.

CARE AND MAINTENANCE

As with all appliances, proper care and maintenance

will keep them in top operating condition and prolong

their life. Your new gas grill is no exception. By

following these cleaning procedures on a timely basis,

your grill will be kept clean and working properly with

minimum effort.

FOLLOW THE BURNER AND BURNER TUBE

CLEANING PROCEDURE BEFORE ASSEMBLY OF

YOUR GRILL.

To reduce the chance of "Flash-back", the procedure

below should be followed at least once a month in

late summer or early fall when spiders are most active,

or when your grill has not been used for an extended

period of time.

Wire brush entire outer surface of burner to

remove loose corrosion.

Clean any clogged holes with a stiff wire (for

example: an open paper clip).

Inspect the burner assembly for any opening

caused by corrosion.

If openings due to corrosion are found, order a

new burner.

Replace the burner and cotter pin as described

in the assembly instructions.

Check the burner for proper location after replac-

ing.

Check to assure the valve orifices are inside of

the burner tubes.

Should "Flash-back" occur, immediately turn the con-

trol knobs to "OFF" and carefully turn the gas supply

off at the gas source.

BURNER CLEANING

Regardless of which venturi cleaning procedure you

used, we recommend that you complete the following

steps to help prolong burner life.

Control Knob

Ignitor

Gas Valve

Orifice

Spark Electrode

Gas Collector Box

BurnerBurner Port

Burner Tube

section of Manifold

PAGE 4

Remove all components from cartons and place within easy reach. Turn the largest carton

upside down and it will provide a comfortable height work surface for grill assembly.

9905TB Parts List

PAGE 5

HOW TO ORDER REPLACEMENT PARTS

AND ACCESSORIES:

Call our service center at 1-800-770-9769,

Monday through Friday 8:00 am - 4:30 pm,

CST.

To make sure you obtain the correct replace-

ment part(s) for your Baker's & Chef Gas

Grill, please refer to the parts list on this

page. The following information is required

to assure getting the correct part:

1. Gas Grill Model Number (see AGA sticker

2. Part Number

3. Description

4. Quantity of parts needed

Please allow sufficient time to process and

ship.

IMPORTANT: Keep this assembly and op-

erating instruction manual for convenient

referral and for part replacement.

IMPORTANT: Use only factory authorized

parts. The use of any part that is not factory

authorized can be dangerous. This will also

void your warranty.

QTY.REF#PART#DESCRIPTION

on grill)

9905TB Parts List

PAGE 6

1a.

1b.

1c.

LID PLATE-Stainless Steel

LID SIDE PANEL, RIGHT

LID SIDE PANEL, LEFT

HEAT INDICATOR

ROUND LID HANDLE-Stainless Steel

CAST IRON COOKING GRID

STEEL FLAME TAMER

GREASE DRAINING TRAY

BOWL FRONT PANEL

BOWL REAR PANEL

BOWL SIDE PANEL, RIGHT

BOWL SIDE PANEL, LEFT

CAST IRON BURNER

GREASE RECEPTACLE

SPARK ELECTRODE W. WIRE

GAS VALVE ASSEMBLY

GAS MANIFOLD

CONTROL PANEL-Stainless Steel

CONTROL KNOB

HEAT SHIELD FOR CONTROL PANEL

SIDE SHELF-Stainless Steel

SIDE SHELF BRACKET

SIDE PANEL

BOTTOM SHELF BRACKET-REAR

BOTTOM SHELF BRACKET-FRONT

BOTTOM SHELF

CART LEGS-WHEEL SIDE

CART LEGS-CASTER SIDE

WHEEL

WHEEL HUB

CASTER

REAR PANEL

TANK HOOK

TANK-HOLDING STRAP

REGULATOR

LIGHTING STICK

DOOR BRACKET

DOOR PANEL-Stainless Steel

DOOR KNOB

TANK HOLDER

HEAT-INSULATING SPACER-Phenolic

CROSS OVER CHANNEL

NAME PLATE

U-SHAPE INSERT

CAP FOR SIDE SHELF BRACKET

CASTER SEAT

REAR WIND SHIELD

BACK BURNER

GAS TUBE ASSEMBLY

COVER FOR GAS TUBE

SPARK ELECTRODE W. WIRE

COVER FOR BACK BURNER

WIND SHIELD, RIGHT

WIND SHIELD, LEFT

ORIFICE

GAS VALVE ASSEMBLY FOR BACK

BURNER

P0129C

P0146A

P0147A

P0615C

P0234A

P1621C

P1721B

P2726A

P0733A

P0734A

P0729A

P0730A

P1925A

P2717A

P2623A

P3229T

P5029A

P2943A

P3409B

P2943B

P1133B

P1207A

P4318A

P1034D

P1034E

P1034F

P0929B

P0829C

P5106C

P5113A

P5109B

P4317B

P4023C

P4008E

P3632D

P5540A

P4407B

P4329A

P3419A

P4023B

P5573A

P2219A

P0435A

P5574A

P4517A

P4519A

P8089A

P1934A

P3512A

P8084A

P2624A

P8085A

P8086A

P8086B

P5633A

P3229U

7a.

7b.

7c.

7d.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

24.

25.

26.

27.

28.

29.

30.

31.

32.

33.

34.

35.

36.

37.

38.

39.

40.

41.

42.

43.

44.

45.

46.

47.

48.

49.

50.

51.

Parts List

The following table illustrates a breakdown of the screwpack. It highlights what

components are used in the various stages of assembly.

Actual Sizes:

A. 5/16" WHEEL BOLT x 2

J. SPRING

WASHER x 2

M. 5/16" NUT

x 2

B. 1/4" x 2 1/2" PHILLIPS HEAD SCREW x 10

L. 1/4" LOCK

NUT x 14

C. 1/4" x 2 1/4" SQUARE BOLT x 8

D. 1/4" x 1/2" SQUARE

COLLAR SCREW x 1

E. 1/4" x 1/2" PHILLIPS

HEAD SCREW x 2

H. WING NUT x 1

I. PLAIN

WASHER x 1

F. No.8-36 UNF x 1"

PHILLIPS HEAD SCREW x 2

G. 3/16" x 3/4" PHILLIPS

HEAD SCREW x 4

1/4" x 2 1/2" PHILLIPS HEAD SCREW

1/4" x 3/4" PHILLIPS HEAD SCREW

1/4" LOCK NUT

1/4" x 2 1/2" PHILLIPS HEAD SCREW

1/4" LOCK NUT

1/4" x 1/2" SQUARE COLLAR SCREW

PLAIN WASHER

WING NUT

3/16" x 3/4" PHILLIPS HEAD SCREW

5/16" WHEEL BOLT

SPRING WASHER

5/16" NUT

1/4" x 1/2" PHILLIPS HEAD SCREW

1/4" x 2 1/4" SQUARE BOLT

1/4" LOCK NUT

No.8-36 UNF x 1" PHILLIPS HEAD SCREW

(ALREADY SCREWED INTO DOOR KNOBS)

3/16" x 1/2" PHILLIPS HEAD SCREW

COMPONENTS USES

ASSEMBLES 2 BOTTOM SHELF BRACKETS TO

THE CART LEGS

SECURES GRILL BOWL ONTO THE CART

ATTACHES TANK HOLDER TO THE CROSS BRACE

OF WHEEL-SIDE CART LEGS

SECURES TANK HOOK TO THE LEFT SIDE OF

GRILL BOWL

SECURES REAR PANEL TO THE CART

SECURES WHEELS ONTO THE CART LEGS WITH

AXLE HOLES

ATTACHES DOOR BRACKET TO THE CART

ATTACHES 2 SIDE SHELVES TO THE CART LEGS

INSTALLS THE KNOBS ONTO THE DOOR PANELS

SECURES REAR WIND SHIELD TO THE BACK OF

GRILL CART.

REF.

PAGE 7

(found in door knobs)

N. 1/4" x 3/4" PHILLIPS

HEAD SCREW x 4

K. 3/16" x 1/2"

PHILLIPS HEAD

SCREW x 2

Assembly Instructions

Before installing the bottom shelf brackets, make

sure: A) the ledges of both bottom shelf brackets

face each other B) the bottom shelf bracket equipped

with door stop must be located in the front C) the

side of Cart Legs having a threaded hole for Door

Bracket must face inwards. Refer to ILL. 1.

Install the bottom shelf brackets between cart legs.

Align the threaded holes on the ends of bottom shelf

bracket with the holes on cart legs. Screw loosely

using 8 of the "B" 1/4" x 2-1/2" phillips head screws.

Insert the screw through the Cart Leg, then

match the screw end with the threaded hole on

the Bottom Shelf Bracket.

Attach the Tank Holder to the cross brace between

both Wheel-side Cart Legs as shown in ILL. 1. Align

the holes on Tank Holder with holes on the cross brace.

Fix firmly by using 2 of the "B" 1/4" x 2-1/2" phillips

head screws and 2 of the "L" lock nuts.

Install the Wheel to a Wheel-side Cart Leg by inserting

one "A" wheel bolt through the Wheel and Cart Leg

as shown in ILL. 2. Then tighten securely using one

"J" spring washer and one "M" 5/16" nut provided.

Snap Wheel Hub in place and repeat steps for second

wheel.

Secure the Caster to the bottom of the Castor-side

Cart Leg by turning the threaded caster stem

clockwise until full stop. Fasten firmly using a

wrench.

Attach the rear panel to the cart legs as shown in

ILL. 3. Align the holes on panel with the holes on

cart legs. Fix firmly by using 4 of the "G" 3/16"

x 3/4" phillips head screws provided.

Tighten the loosely attached screws in step 2 for

fastening both Cart Legs and Bottom shelf brackets

together.

Secure the Lighting Stick to the top of the right side

panel. The tapping screw is already attached to the

lighting stick.

Place the bottom shelf over the ledges of both bottom

shelf brackets.

Before attempting to assemble your gas grill, check that

all the necessary parts have been included using the

parts lists on page 5, 6 and 7. Inspect grill and trolley

parts for damage as you proceed. Contact our service

center regarding replacement of any damaged parts. Do

not assemble or operate a barbecue grill that appears

damaged.

While it is possible for an individual to assemble this

gas grill, we recommend asking for the assistance of

another person when maneuvering some of the larger

or heavier pieces. You may need both Adjustable

Wrench and Phillips Screw Driver (not provided) for

securing the nuts and screws.

HINT:

PAGE 8

TANK

HOLDER

ILL. 1

DOOR

STOP

WHEEL-SIDE

CART LEG

CASTOR-SIDE

CART LEG

BOTTOM SHELF

BRACKET

THREADED HOLE FOR

DOOR BRACKET

ILL. 3

BOTTOM

SHELF

SIDE

PANEL

REAR

PANEL

LIGHTING

STICK

ILL. 2

WHEEL HUB

CASTER

Assembly Instructions

10.

Attach a (pre-assembled) stainless steel side shelf

to each side of grill as shown in ILL. 4. Align the

square holes of the side shelf with holes at upper

section of each cart leg. Screw loosely using 8

of the "C" square bolts and 8 of the "L" lock nuts.

Slide the U-shape Inserts into each Side Shelf

Bracket. The Inserts cover the square bolts inside

and add support. Fix firmly by tightening lock nuts.

Place the Grill Bowl over the cart as shown in ILL.

5. Align the holes on both sides of Grill Bowl with

the two (2) holes at the bowl support bracket.

Tighten firmly using 4 of "N" 1/4" x 3/4" phillips

head screws and 4 of "L" lock nuts. You may

have to lift up the Grill Bowl slightly to align the

holes properly.

Attach the Tank Hook to the left side of Grill Bowl.

as in ILL. 6. Align the hole on Tank Hook with

the hole on the grill Bowl and tighten securely using

1 "H" wing nut, one "D" 1/4" x 1/2" square collar

screw and one large "I" plain washer.

Slide the Grease Draining Tray in position over

the ledges under Grill Bowl from the rear of Grill.

See ILL. 5.

Grease Receptacle should be positioned centrally

under Grease Draining Tray.

11.

12.

PAGE 9

ILL. 4

U-SHAPE

INSERT

STAINLESS STEEL SIDE SHELF,

PRE-ASSEMBLED WITH BRACKETS

GREASE

RECEPTACLE

GREASE

DRAINING TRAY

ILL. 5

ILL. 6

TANK HOOK

Assembly Instructions

Please find the Door Bracket and Doors in the

same box as Grill Head.

Attach the Door Bracket to cart legs (under

Control Panel). Be sure the folded strip of the

bracket is closest to the cart legs. Then align

the holes on both ends of the bracket with the

threaded holes on the cart legs. Fix the Door

Bracket by screwing 2 of the "E" 1/4" x 1/2"

phillips head screws loosely. Refer to ILL. 7.

Locate the hinge holes for the door on the Bottom

Shelf Bracket. Insert the door hinges into these

holes and holes on Door Bracket. Push the Door

Bracket down to an even level and then tighten

it securely using a screw driver. See ILL. 7.

Install the door knobs onto the door plates with

the 2 "F" No.8-36 UNF x 1" phillips head screws

(can be found with the door knobs).

Install the Rear Wind Shield to the back of grill

cart. Fix securely using 2 of the "K" 3/16" x

1/2" phillips head screws. See ILL. 8

Install the Heat Indicator by inserting it into the

hole on upper left side of Grill Lid. Adjust it

to level position, then tighten securely using lock

washer and wing nut provided in the Heat

Indicator box. See ILL. 9.

13.

15.

BUILT-IN IGNITOR / ELECTRODE CHECK

Before placing the flame tamers or cooking grids,

ensure that the gap between each spark elec-

trode tip and the collector box is approximately

3/16". Adjust if necessary.

Push and turn the Control Knob to HIGH, a blue

spark should be produced at the electrode tip.

If not, check ignition wire, the terminal of wire

to the ceramic electrode could become loose in

delivery. Push in the terminal for a tight

connection.

Push and turn the Control Knob to HIGH for blue

spark again.

16.

17.

14.

PAGE 10

ILL. 8

ILL. 7

DOOR KNOB

DOOR

BRACKET

FOLDED STRIP USED AS

DOOR STOP

ILL. 9

HEAT INDICATOR

GRILL LID

REAR WIND SHIELD

Assembly Instructions

COOKING COMPONENT INSTALLATION

Place Steel Flame Tamers on the lower ledge of

Grill Bowl. See ILL. 10.

Place Cast Iron Cooking Grids on the ledge of

Grill Bowl above Flame Tamers.

WARNING :

Now your gas grill is ready to use. Before

first use and at the beginning of each

barbecue season and whenever LP gas

cylinder is changed.

Please read safety, lighting and operating

instructions carefully.

Check gas valve orifices, venturi tubes and

burner ports for any obstructions.

Perform gas leak check (see page 2).

IMPORTANT: The Grill is not designed for use with

lava rock or briquettes and the use of such items will

void the warranty.

CONNECTING TO GAS SOURCE

Insert the Tank-Holding Strap through the two (2)

slots on Side Panel. See ILL. 11. Hang filled

gas tank on the Tank Hook attached to the Grill

Bowl. The ring foot of the gas tank will rest on

the Tank Holder. Fasten the gas tank using the

Tank-Holding Strap. Make sure tank valve is in

its full off position (Turn clockwise to stop).

Check tank valve features to ensure it has proper

external mating threads. (Type 1 connection per

10-94 AGA Requirement)

Make sure all burner valves are in their off position.

Inspect valve connection ports and regulator as-

sembly. Look for any damage or debris. Remove

any debris. Inspect hose for damage. Never

attempt to use damaged or plugged equipment.

See your local LP gas dealer for repair.

When connecting regulator assembly to the tank

valve, hand tighten nut clockwise to a positive stop.

Do Not use a wrench to tighten. Use of a wrench

may damage quick coupling nut and result in a

hazardous condition.

Open tank valve fully (counter-clockwise). Use a

soapy water solution to check all connections for

leaks before attempting to light grill. If a leak is

found, turn tank valve off and do not use grill until

repairs can be made by a local LP gas dealer.

CAUTION: When the appliance is not in use, the

gas must be turned off at the supply cylinder.

To disconnect LP gas cylinder:

a) Turn the burner valve off.

b) Turn the tank valve off fully.( Turn clockwise to stop.)

c) Detach the regulator assembly from tank valve by

turning the quick coupling nut counter-clockwise.

PAGE 11

These holes are for rotisserie mounting bracket use.

ILL. 10

CAST IRON

COOKING GRID

STEEL FLAME

TAMER

ILL. 11

REGULATOR

COUPLING NUT

TANK-HOLDING

STRAP

TANK HOOK

TANK HOLDER

SIDE PANEL

Become familiar with safety guidelines at front of

manual. DO NOT SMOKE WHILE LIGHTING GRILL

OR CHECKING GAS SUPPLY CONNECTIONS!

Check to see that cylinder is filled.

Check that end of each burner tube is properly located

over each valve orifice.

Make sure all gas connections are securely tightened.

TEST FOR LEAKS WITH A SOAP SOLUTION,

NEVER WITH A FLAME. (Gas Leak Check

instructions are on page 1).

Always open lid before lighting.

Set control knobs to "OFF" and open the gas supply

cylinder valve.

Ignite only the burners you intend to use, using the

same method for each:

Adjust control knob(s) to desired temperature.

Lighting & Operating Instructions

LIGHTING PROCEDURES

Turn off gas at source, turn control knob to "OFF", and

wait five minutes before trying again.

Check gas supply/connections.

Repeat lighting procedure and , if grill still fails to

operate properly, TURN "OFF" GAS AT SOURCE,

TURN CONTROL KNOBS TO " OFF", wait for grill to

cool and check the following:

Misalignment of burner tube(s) over orifice(s).

CORRECTION: Reposition burner tube to properly

seat over orifice.

Obstruction in gas line

CORRECTION: Remove fuel line from grill. DO NOT

SMOKE! Open gas supply for one second to blow any

obstruction from fuel line. Close off gas supply at

source and reconnect fuel line to grill.

Plugged orifice

CORRECTION: Remove cooking grids and flame

tamers. Remove burners from bottom of grill bowl by

pulling cotter pin from beneath burner "foot" using a

screwdriver or needlenose pliers. Carefully lift each

burner up and away from gas valve orifice. Unscrew the

orifice from each gas valve and gently clear any

obstruction with a fine wire. Re-install each orifice, re-

install burners over orifices and seat each burner "foot"

into mounting bracket at bottom of grill bowl. Replace

cotter pins and cooking components.

If an obstruction is suspected in gas valve(s) or gas

valve bracket, please contact your local LP gas service

person for assistance.

Misalignment of ignitor on burner

CORRECTION: Check for proper position of electrode

tip. The tip of the electrode should be pointing toward

the tip of the collector box. The gap between the spark

electrode and the tip of the gas collector box should

be 3/16". Adjust if necessary. With gas supply closed

and all control knobs set to "OFF" check each positive

ignitor individually for presence of spark at electrode.

In turn, push each control knob in fully and rotate about

1/4 turn to the left (counter-clockwise) until a click is

heard; the trigger hitting the strike block should pro-

duce a blue spark at the electrode tip. Return control

knob to "OFF" before checking next ignitor.

If re-ignition is necessary while the gas grill is still hot, you

must wait for a minimum of five minutes before commenc-

ing to re-ignite (this allows accumulated gas fumes to

clear).

If all checks/corrections have been made and gas grill still

fails to operate properly, contact the Grand Hall Service

Center, or your local LP gas service person.

FLASH BACK:

Should fire occur in and around the burner tubes, imme-

diately turn off gas at its source and turn the control

knob(s) to "OFF". Wait until the grill has cooled, then clean

the burner tubes and burner ports as described on page

Open lid.

Push Control knob in and HOLD it down while you

turn knob left about 1/2". This allows gas to collect.

After holding for 2 seconds, turn knob leftward to the

ignition point (see lightning bolt). You may need to

re-click ignitor 3 or 4 times to light.

If burner does not light, turn gas off and wait 5

minutes before retrial. If unsuccessful after retrial,

wait a few minutes and light by match.

NOTE: As long as one ignitor is in working order, other

burners can be ignited from operating burner, in succes-

sion. If, for some reason, all ignitors fail to produce a spark

at the electrode tip, grill can be lit with a paper book match.

NOTE: To light gas grill with a match, follow steps 1 to 6 above.

Then, insert lit paper book match with lighting stick through

the lighting hole on right side of grill bowl. Press in right

control knob and rotate left to "HI" setting to release gas.

Burner should light immediately. If more burners are

needed, press in and rotate next control knob to light burners

in succession. Turn off burners not needed, and adjust to

desired cooking temperature. See Page 14, ILL. 12.

CAUTION: Do not move trolley while grill is in operation.

If the grill fails to operate properly:

PAGE 12

Lighting & Operating Instructions

CAUTION: Do not attempt to disconnect any gas fitting

while your barbecue is in operation.

As with all appliances, proper care and maintenance will

keep them in top operating condition and prolong their life.

Your gas grill is no exception. By following these cleaning

procedures on a timely basis, your grill will be kept clean

and working properly with minimum effort.

CLEANING & MAINTENANCE

Burn-off: Before cooking on your gas grill for the first time,

burn off the grill to rid it of any odors or foreign matter by

igniting the burners, closing the lid, and operating at "HI"

setting for about five minutes. You may then either set the

controls to "OFF" or cook on your grill immediately by

turning the control knobs to a lower setting.

CAUTION: Operating grill on "HI" setting for longer than

five minutes may damage certain parts of your grill.

DO NOT LEAVE GRILL UNATTENDED.

Preheating: The grill lid is to be in a closed position during

the preheat time period. It is necessary to preheat the grill

for a short time before cooking certain foods, depending

on the type of food and the cooking temperature. Foods

that require a high cooking temperature need a preheat

period of five minutes; foods that require a lower cooking

temperature need only a period of two to three minutes.

There is no need to pre heat for casseroles, roasts or other

foods that require slow cooking.

COOKING TEMPERATURES

HIGH setting - Use this setting only for fast warm-up, for

searing steaks and chops, and for burning food residue

from the cooking grids after the cookout is over. Rarely,

if ever, do you use the HIGH setting for extended cooking.

MEDIUM setting - Use this setting for most grilling, roasting

or baking, and for cooking hamburgers and vegetables.

LOW setting - Use this setting for all smoke cooking,

rotisserie cooking, and when cooking very lean cuts such

as fish.

These temperatures vary with the outside temperature and

the amount of wind.

Cooking with Indirect Heat: You can cook poultry and

large cuts of meat slowly to perfection on one side of the

grill by indirect heat from the next burner. Heat from the

lighted burner circulates gently throughout the grill, cook-

ing the meat or poultry without any direct flame touching

it. This method greatly reduces flare-ups when cooking

extra fatty cuts, because there is no direct flame to ignite

the fats and juices that drip down during cooking. Place

a drip pan slightly smaller than the cut of meat on the flame

tamer surface under the meat being cooked. This will allow

you to catch meat juices for making gravy.

Flare-Ups: The fats and juices that drip from the meat

cause flare-ups. Since flare-ups impart the distinctive

taste and color for food cooked over an open flame, they

should be expected and encouraged within reason.

Nevertheless, uncontrolled flaring can result in a ruined

meal.

CAUTION: If burners go out during operation, close gas

supply at source, and turn all gas valves off. Open lid and

wait five minutes before attempting to re-light (this allows

accumulated gas fumes to clear).

CAUTION: Should a grease fire occur, close gas

supply at source, turn off all burners and leave lid

closed until fire is out.

OPERATING PROCEDURE

CLEANING THE COOKING GRIDS

After cooking, turn control knobs to "OFF" and let grill cool

before attempting to clean your cooking grids.

Before first use and periodically it is suggested that you

wash the cooking grids in a mild soap and warm water

solution. You can use a wash cloth or a vegetable brush

to clean your cooking grids if you desire. But take care not

to chip the porcelain coating because it will void your

warranty.

CLEANING THE FLAME TAMER

Periodically use a wire brush to remove stubborn burned

on cooking residue (and any rust that may have devel-

oped), wash in warm soapy water and dry. Coat with

cooking oil.

Rusting may appear on the flame tamers. This is a natural

oxidation process and does not affect the performance of

the flame tamer or adversely affect the taste of the food.

Application of cooking oil to the flame tamers between

uses can help prolong the life of the flame tamers. Grand

Hall does not warrant the flame tamers against rust unless

the flame tamer is completely rusted through.

CLEANING THE BURNER TUBES AND BURNER

PORTS( to prevent FLASH-BACK)

To reduce the chance of FLASH-BACK, the procedure

below should be followed at least once a month in late

summer or early fall when spiders are most active, or when

your grill has not been used for an extended period of time.

We suggest several different ways for cleaning the burner

tubes. Use the procedure that is most convenient for you:

Turn the burner valve off.

Turn gas off at tank.( Turn clockwise to stop.)

Detach the regulator assembly from tank valve by

turning the quick coupling nut counter-clockwise.

Remove cooking grids, flame tamers and grease col-

lectors from grill.

Remove burners from bottom of grill bowl by pulling

cotter pin from beneath burner "foot" using a screw-

driver or needlenose pliers.

Carefully lift each burner up and away from gas valve

orifice.

PAGE 13

Regardless of which cleaning procedure you use, we sug-

gest you complete the following steps to prolong burner life.

Wire brush entire outer surface of burner to remove

food residue and dirt.

Clean any clogged ports with a stiff wire such as an

open paper clip.

Inspect the burner for damage (cracks or holes) and if

such damage is found, order and install a new burner.

After installation, check to insure that gas valve

orifices are correctly placed inside ends of burner

tubes. Also check position of spark electrode.

Bend a stiff wire (a lightweight coat hanger works well)

into a small hook. Run the hook through each burner

tube and into the burner several times.

Using a narrow bottle brush with a flexible handle (do not

use a brass wire brush), run the brush through each

burner tube and into the burner several times.

Use an air hose to force air through the burner tube and

out through the burner ports. Observe each port and

make sure air comes out every hole.

CLEANING THE GREASE TRAY

Periodically, the grease tray should be emptied and washed

in a mild detergent and warm water solution.

Annual Cleaning of Grill Housing

Burning-off the grill after every cookout will keep it ready for

instant use, however, once a year you should give the entire

grill a thorough cleaning to keep it in top operating condition.

Interior:

Cover the gas valve orifices with a piece of aluminum foil.

Brush the grill bowl with a stiff wire brush, then wash with

mild soap and warm water. Rinse thoroughly and let dry.

Remove foil from orifices and check for obstruction.

Turn the burner valve off.

Turn gas off at tank. (Turn clockwise to stop.)

Detach the regulator assembly from tank valve by

turning the quick coupling nut counter-clockwise.

Remove and clean (as explained before) the cooking

grids, flame tamers and burners.

Cleaning & Maintenance Instructions

IMPORTANT: DO NOT line the grill bowl with aluminum foil,

sand or any absorbent substance that could prevent drain-

age to grease collector tray. A grease fire could occur.

Exterior Painted Steel Surfaces:

Much of your grill is made of heavy steel and should provide

years of trouble-free service. Should you decide to touch

up any scratches in the paint which may occur with use,

a touch-up paint designed for use with high temperature is

available. Follow these steps for best paint results:

Shut off gas supply at source and disconnect fuel line

from gas valve manifold. Protect fuel line fitting.

Remove loose paint by lightly sanding surface(s) with

a medium grit emery cloth or a fine grit sandpaper.

Remove any dirt or grease by washing the surface(s)

with a mild soap and warm water solution.

Rinse with clean water and allow surface to dry

thoroughly or wipe the area with vinegar.

Apply touch-up paint, following instructions on can.

Allow paint to air dry completely, and apply a second

coat if necessary. IMPORTANT: Let paint dry for 24

hours before using gas grill.

Occasionally observe burner flame for correct operation.

See ILL. 12.

VISUALLY CHECKING BURNER FLAMES

ILL. 12

Lighting

Hole

PAGE 14

Check for proper position of electrode tip. The tip of the

electrode should be pointing toward the tip of the

collector box. The gap between the spark electrode

and the tip of the gas collector box should be 3/16".

Replace burners and adjust spark electrode collector

box. Edge of collector box should overlap burner port.

Replace flame tamers, cooking grids.

Reconnect to gas source and observe burner flame for

correct operation.

10.

11.

Exterior Stainless Steel Surfaces:

Daily weathering and high heat associated with grill cooking

can cause exterior stainless surfaces to "tan". Follow these

directions for best results, and NEVER clean a hot grill.

Shut off gas supply at source and disconnect fuel line

from gas valve manifold. Protect fuel line fitting.

Remove dirt or grease using a soft cloth, then polish

stainless surfaces with a Foam Spray cleaner designed

for stainless steel. Never use an abrasive cleaner or

scrubber that may scratch your stainless surfaces.

Dry with a soft cloth and let air dry before restarting grill.

Frequently Asked Questions

PAGE 15

Our Service Center is available during business hours to assist you with your new Bakers & Chefs gas grill.

We're here to take your questions, listen to your input, and we're certainly open to new recipe ideas! For

your convenience we've listed some of the more commonly asked questions here, but if you have more

questions or comments please call us Monday through Friday, 8:00 am to 4:30 pm CST, at 1-800-770-9769.

Q. I am not familiar with Grand Hall. How long have you been in the gas grill business?

A. Grand Hall has been in business for 22 years manufacturing gas regulators, valves, burners, grills and

assorted parts and accessories for the grill-related industry. Since 1996 we have been manufacturing

the top-of-the-line Bakers & Chefs - a private label grill line commissioned by Sam's Club.

Q. I want to convert my Bakers & Chefs LPG (liquid propane gas) grill to natural gas. Is this safe?

A. Your Bakers & Chefs gas grill is manufactured to exact specifications and is approved by the American

Gas Association (AGA) for use with an LPG cylinder only. We the manufacturer support the U.S.

Government in it's efforts to prevent after-market conversions of gas appliances. For your own safety,

conversion kits are not available and attempts to convert your grill will void your product warranty.

Q. When I mail my Warranty Registration card to the Service Center, will I start getting a lot of junk mail?

A. Grand Hall does not sell or offer it's customer list to other companies. You'll notice the card is quick and

simple to complete. We only ask for pertinent information that enables us to match your name with the

correct model number, date ofpurchase and serial number - all of which must be on-file if you ever need

replacement parts, accessories or want to place a warranty claim. Your information is held private, and

will be on-file here at the Service Center. You can mail the card, or fax it directly to (214)-553-0090.

Q. My Warranty Registration card asks for the serial number off my grill. Where can I find this information?

A. Each Bakers & Chefs gas grill has an individual serial number which may include five numbers

and one letter. However, your serial number may be different. You will find this serial number (and the

model number) on the silver AGA label, placed on the side of your grill control panel. It is very important

to include your serial number on the warranty registration card exactly as it appears on your grill.

Q. How long are parts available for my current grill model?

A. Grand Hall maintains an ample inventory of parts for current gas grills. In the rare event a grill part has

been discontinued or modified, Grand Hall reserves the right to substitute a similar part at our option.

Q. The regulator and hose that came with my Bakers & Chefs grill does not fit my older LPG tank. Why?

A. The U.S. Government regulates gas appliances and LPG cylinder fittings. Increased regulations have

altered the tank fittings over the last few years and they continue to change as the industry develops

improved technology. We apologize for any inconvenience, but if your tank does not fit the current

regulator it means your tank is outdated and must be replaced.

Q. I bought my Bakers & Chefs grill years ago and it looks different from the one I saw in the store

recently. What has changed?

A. Despite outward appearances, the Bakers & Chefs gas grill remains virtually unchanged. Sam's Club

does alter the hood color, cart construction and/or accessory options periodically in order to keep the

product line fresh and new. But rest assured, the Bakers & Chefs grill you see today offers the same

superior performance, quality and value as all previous models.

Note: Having your warranty registration card with serial number on file allows our Service Center to match your

grill model with the appropriate parts and accessory options.

Q. I want to take good care of my investment, so what is the best way to clean my Bakers & Chefs?

A. As with all appliances, proper care and maintenance will keep them in top operating condition and help

prolong their life. Your Bakers & Chefs gas grill is no exception. Follow the "Cleaning & Maintenance"

instructions in this instruction manual on a timely basis, and your grill will offer you years of enjoyment.

Q. Is it true that stainless steel grill hoods can turn a "wheat" color after use?

A. Yes, this is very common with stainless steel hoods because of the intense heat produced from the grill.

This coloration does not affect the performance of the grill hood, but you still may want to routinely clean

the stainless steel anyway. On a cold grill - with no flame nearby, use paint thinner on a clean cloth and

rub onto stainless steel hood. Allow to dry thoroughly before cooking on grill.

Q. What can cause grills to rust, and what affect does it have on the materials?

A. Rusting is a natural oxidation process and may appear on steel flame tamers at any time. Because your

grill is manufactured with heavy gauge steel, rust will not affect the performance of your grill or affect the

taste of your foods. Grand Hall can not warrant against rust unless the components are completely

rusted through.

Q. How can I remove rust from my grill? Is there a treatment I can use for rust?

A. Here is a quick and easy way to remove annoying rust: Brush off rusted surfaces and create a mixture

of 1 part vinegar and 1 part water. Spray this solution onto rusted areas to dissolve rust, then scrub with

wire brush if necessary. To treat against rust, keep all cooking surfaces and steel flame tamers lightly

oiled at all times. Vegetable oil works well for this and helps to prolong the life of your steel cooking

surfaces and any cast-iron cooking accessories.

Q. What does treating cast-iron mean, and what is the benefit?

A. Treating cast-iron will make foods stick less (which means cooking and clean-up are both

easier) and helps prolong the life of cast-iron accessories. It's easy to do, just wipe the cast-iron

with vegetable oil, olive oil, canola oil, grease, etc., then heat on high in the grill for a few

minutes. After cooking you can wipe a greased cloth along the cast-iron and much of the

residue will wipe away so you don't actually have to soak?the accessory. After continued use,

the cast-iron will retain flavor and memory of previous recipes, which is what they mean by

seasoned pan.?For best results, it is best to treat cast-iron before, and after cooking.

Frequently Asked Questions

PAGE 16

Making The Good Life Even Better!

Congratulations! You are now the owner of the new Bakers & Chefs gas grill, an outdoor kitchen

system that is redefining the barbecue. In fact, Bakers & Chefs grill is well on the way to rewriting the art of

cooking; making it easier, tastier and more accessible to those who enjoy great food in the great outdoors.

Gone are the days when Dad labored over temperamental charcoal to scorch a steak while Mom

raised the temperatures in the kitchen, boiling potatoes and corn. With this revolutionary cooking system,

you're in control. No more side dishes cooling on the table as they await the underdone meat. And forget

about dripping sauces and marinades from the stove to the deck!

Why not stir fry veggies for your vegetarian friends? Or smoke a trout? Perhaps you'll even opt to bake

a desert for the sweet tooth in your family.

There's no need for amateur's anxiety. In no time, you'll get a good grip on Bakers & Chefs nearly

limitless capabilities. Stir frying. Steaming. Smoking. Stewing. Sauteing. Searing. Deep frying. Roasting.

Poaching. Pan frying. Baking. And of course, grilling. Just remember, if you can do it in a kitchen, you can cook

it on your Bakers & Chefs grill.

Now read over the following cooking methods and recipes. You'll find plenty of delicious, nutritious and

do-able recipes that will embellish your table and have guests lining up for more. Watching the waistline?

Escape the cycle of over-processed convenience foods! What better way to reduce fat than by grilling meats

or enhancing your diet with more vegetables - prepared to mouth watering perfection?

Whatever your appetite, no matter the recipe, your creativity will soar with this grill that is also an oven,

a frying pan, a wok, a smoker and deep fryer. Bakers & Chefs unique flame control system ensures perfect

results and pleased customers each and every time. So tie on your apron and prepare to rewrite your own

culinary history!

Burn-off: Before cooking on your gas grill for the first time, burn off the grill to get rid of any odors or foreign

matter by igniting the burners, closing the lid, and operating at "HI" setting for about five minutes. You may then

either set the controls to "OFF" or cook on your grill immediately by turning the control knobs to a lower setting.

CAUTION: Operating grill on "HI" setting for longer than five minutes may damage certain parts

of your grill. WHILE COOKING, DO NOT LEAVE YOUR GRILL UNATTENDED.

BEFORE FIRST USE:

PAGE 17

Outdoor cooking has taken on a new dimension with the introduction of Bakers & Chefs grill. You will

quickly come to realize that it is truly a stove on wheels that can do everything from frying, poaching, grilling

and smoking to roasting succulent meats.

THE BASICS:

The two methods of cooking referred to frequently throughout this section are direct and indirect

cooking. An explanation of both is necessary before you launch into your first meal. Some recipes will require

using both direct and indirect cooking methods.

DIRECT COOKING targets heat (flame) directly under the food. Use this method when grilling and

searing meats, poultry or fish. The Bakers & Chefs cooking grids, griddle, cooking pan or wok/saute pan can

be used for direct cooking. Side dishes, deep frying and smoking are just a few examples of meals best cooked

in this manner. Unless otherwise noted, direct cooking requires the hood to be open, allowing you to watch

as your dinner is prepared.

INDIRECT COOKING is exactly as it sounds. Heat is directed around the food from an opposing

burner(s) - not the burner directly underneath. Indirect cooking is always done with the hood down, creating

an atmosphere similar to your kitchen oven. Imagine you want to roast a piece of meat on your Bakers & Chefs

grill. You would select the indirect cooking method because it is closest to the way you would roast in your

kitchen. First, remove the center cooking grid and insert the cooking pan or griddle, with your meat placed on

top. Then, the left and/or right burners are ignited and the hood closed. If you are roasting a large quantity of

items that require more space, you may place the items on two cooking grids with the farthest outer burner

ignited. Either way, indirect cooking is only effective with the hood down.

PREHEATING YOUR BAKERS & CHEFS GRILL:

The grill lid is to be in a closed position during the preheat time period. It is necessary to preheat the

grill for a short time before cooking certain foods, depending on the type of food and the cooking temperature.

Foods that require a high cooking temperature need a preheat period of five minutes; foods that require a

lower cooking temperature need only a period of two to three minutes. There is no need to pre heat for

casseroles, roasts or other foods that require slow cooking.

PREPARATION OF THE COOKING SURFACES:

After preheating your grill, coat the cooking grids with cooking oil to prevent food from sticking.

When you've finished cooking, leave your grill running for 5 minutes on high to burn off food residue. Then

brush the cooking surfaces with a fiber or brass wire brush. All cooking surfaces can be further cleaned with

hot soapy water. To season your grill, keep cooking surfaces lightly oiled at all times. Simply wipe an oiled

cloth over the cooking surfaces after each cookout. Vegetable oil is best for this purpose. The seasoning

process keeps foods from sticking, and helps prolong the life of your cooking surfaces as well.

Cooking Methods

Cooking Techniques

Your Bakers & Chefs grill is capable of preparing mouth watering meals using many different cooking

techniques. Because every family enjoys different types of cooking, we offer a variety of quality-made cooking

accessories that allow you to customize the Bakers & Chef grill to meet your particular needs. The cooking

techniques on the following pages incorporate these custom-fit accessories. However, you may use your

own cookware to accomplish similar results.

Grill - using the standard Bakers & Chefs cast-iron cooking grids or the optional griddle/hotplate

Rotisserie Cook - using the optional electric rotisserie

Bake, Roast, Smoke and Deep Fry - using the optional cast-iron cooking pan with lid, and fry basket

Stir Fry

- using the optional wok/saute pan

PAGE 18

For those watching their calories, grilling is a low fat cooking technique that lends itself to a wide

range of foods. Your Bakers & Chefs grill is a fast heat source that produces the barbecued appearance

and flavor we all enjoy so much. You can expand dinners for two, to parties for plenty by purchasing larger

cuts and quantities of meat which cook beautifully on the grill. This technique doesn't require much experience

or skill on your part to produce a superb supper.

It's easy! Prepare to grill by preheating for 5 minutes with the burners on high and the hood down.

Before placing the food onto the grill, lightly brush the grill with a little cooking oil. This step isn't necessary

when foods have been marinating in an oil-based marinade.

Your Bakers & Chefs is now ready to grill. Remember to keep the lid open when cooking directly

on the grill. For most foods it's best to start grilling on high. Once the food is seared, reduce the heat to

medium. Foods marinated with ingredients such as honey may burn because of the high sugar content. You

should commence their cooking on medium. A favorite on the grill is sausages. Always cook them slowly and

if they're particularly fatty, it may be best to partially boil them first.

GRILLING MEAT AND POULTRY

Grilling Techniques

BEEF

Turn burners on high and preheat grill 5

minutes with the hood down. Raise hood

and place meat on cooking grid directly

above heat source and cook meat on

both sides until seared. Then reduce

burners to medium and cook until done.

Grilling times will vary according to meat

thickness, so the following times should

be used only as a guide.

HAMBURGER & SAUSAGES

Follow directions for steak and the times

shown to right. For the juiciest burgers

and sausages, cook them using the indi-

rect method. Turn burgers with a spatula

and use tongs with sausages. Do not

puncture meats more than necessary.

POULTRY

Turn burners on high and preheat grill 2-

3 minutes with the hood down. Raise

hood, reduce burners to medium and

cook until done. If you prefer to use the

indirect method - place poultry in center of

grill with left and/or right burners on me-

dium heat and lower hood. Cooking times

may vary based on the size of your food.

Poultry skin is fatty and may flare-up

when cooked directly. So keep an eye on

your grill.

CUT OF MEAT

T-bone steak

Sirloin steak

Beef spare ribs

Porter house steak

New York strip steak

Hamburger

Sausages

Chicken breast

(cook with bone down)

Chicken wings

Drumsticks

Whole bird

(cook with breast up)

APPROX. COOKING TIME

rare: 4-8 minutes

medium: 10-14 minutes

well done: 15-20 minutes

rare: 4-6 minutes

medium: 8-10 minutes

well done: 10-15 minutes

Direct method:

approximately 15 minutes

Indirect method:

up to 30 minutes

Indirect method:

approximately 1 hour

PAGE 19

Grilling Techniques

PORK

Turn burners on high and preheat grill 5

minutes with the hood down. Raise hood,

place pork on cooking grid and cook until

seared. Then reduce heat to medium and

cook until done. Grilling times will vary

according to meat thickness, so the fol-

lowing times should be used only as a

guide.

WHOLE FISH AND WHOLE FILLETS

Grill fish on cooking grid or use the op-

tional griddle (grooved side up). Turn burn-

ers on high and preheat grill 2-3 minutes

with the hood down. Raise hood, and turn

burners to medium heat. Place fish (skin

down) on griddle and cook over direct

heat until done. Use cooking time as a

guide or until fish is opaque but still moist.

FISH FILLETS AND CUBES

Follow same directions from above, using

approximate cooking times shown at right.

Because small fish pieces can drop through

the grid and into the grill we suggest using

the griddle when grilling fish. However, the

cooking grid and a small, flat piece of

aluminum foil will also work fine.

CUT OF MEAT

Pork spare ribs

Chops

Loins

Cutlets

Whole fish

Whole fish fillets

Fish fillets

Boneless cubes

APPROX. COOKING TIME

rare: 4-8 minutes

medium: 10-14 minutes

well done: 15-20 minutes

approximately 10 - 12

minutes per pound or

until fish is opaque

approximately

4 - 5 minutes each side

or until fish is opaque

GRILLING FISH AND SEAFOOD

GRILLING VEGETABLES AND FRUIT

Prepare your fruit or vegetables and brush with butter or basting sauce if desired. To cook indirectly,

place your food on the center grid with the left and/or right burners lit. Or place your food inside the optional

warming rack that hangs inside the grill lid - and light the outer burners. Either way, indirect cooking must be

done with the hood down.

In some instances, you may want to grill vegetables and fruit directly over the heat, using the

standard cooking grids or optional griddle. Foods that work best with direct heat are relatively soft and require

a short cooking time, like mushrooms, zucchini, tomatoes and skewered fruit such as apricots, peaches,

pineapple, strawberries and kiwis. Remember that the hood of the Bakers & Chefs should remain up

when cooking directly.

Grilling times using the indirect method with the hood down will be similar to those for your kitchen oven.

For very firm vegetables - particularly potatoes and yams - we recommend that you partially boil until almost

cooked, before placing them on the grill. Cooking times for foods prepared with the direct method will be much

shorter mainly because of the softness of the food. Timing will be comparable to normal pan frying or grilling.

PAGE 20

Page is loading ...

Bakers & Chefs 9905TB Owner's manual

Brand: Bakers & Chefs

Model: 9905TB

Category: Barbecues & grills

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Bakers & Chefs 9905TB Owner's manual

This manual is also suitable for

Bakers & Chefs 9905TB Owner's manual

Other documents