Draper 137052 Operating instructions

Category
Projection screens
Type
Operating instructions

This manual is also suitable for

Draper 137052 is a wall or ceiling-mounted projection screen designed to provide a clear and stable viewing surface for presentations, movies, or other visual content. It features a slow retraction mechanism to prevent injuries and a locking system to keep the screen in place when not in use. The screen's surface is easy to clean and maintain, with specific care instructions provided for different surface types like matt white, high contrast grey, and glass beaded. Additionally, the screen can be adjusted left or right to achieve the optimal viewing angle.

Draper 137052 is a wall or ceiling-mounted projection screen designed to provide a clear and stable viewing surface for presentations, movies, or other visual content. It features a slow retraction mechanism to prevent injuries and a locking system to keep the screen in place when not in use. The screen's surface is easy to clean and maintain, with specific care instructions provided for different surface types like matt white, high contrast grey, and glass beaded. Additionally, the screen can be adjusted left or right to achieve the optimal viewing angle.

Installation Instructions
Salara/Series M by Draper
Copyright ©2008 Draper Inc. Form SalaraM_Inst08 Printed in U.S.A.
Wall/Ceiling Flush Mounting
Attach Mounting Brackets to wall or ceiling (see Fig. 1). The installer should
furnish screws, toggle bolts, molly bolts, nylon or lead anchors as required
by the mounting surface. Installer also needs to ensure the mounting
surface is reinforced suffi ciently to support the screen. Brackets must be
level with each other.
Figure 1
®
Figure 3
If you encounter any diffi culty installing or ser vic ing your Salara, call your dealer
or Draper, Inc., Spiceland, Indiana, (765) 987-7999; or fax (765) 987-7142.
Wall
Mounting
Bracket
1
1
/2"
Attach the screen by snapping the extrusions on the back of the case onto
the brackets. With the lower edge of the screen case tilted away from the
wall, engage the rib on top of the case with the slot on each bracket. Slide
the screen case along the brackets to adjust the screen location from left to
right if necessary (see Fig. 2). Once the case is in position, pivot the case
back toward the brackets until the lower edge of the case "snaps" into place
with the spring-loaded latch (see Fig. 3).
Extrusions along
back of case
Dimensions
3
11
/16"
5
/16"
3
/8"
1
3
/8"
Case Length
Viewing Surface
5
1
/16"
5
7
/16"
3
1
/8"
3
7
/16"
5
/16"
3
13
/16"
Floating Mounting Brackets
Figure 2
1
23
Mounting
Bracket
1
1
/2"
Ceiling
Operating Instructions—Standard
To lower picture surface, pull screen down. Hesitate—then allow screen to
retract very slowly until it locks in place.
To raise picture surface, pull screen down and, while holding, allow for slow
retraction into the case to reduce risk of injury from falling screen.
Operating Instructions—AutoReturn
To lower picture surface, pull screen down. Hesitate—then allow screen to
retract very slowly until it locks in place.
To raise picture surface, pull screen down gently until it stops, then release.
Matt White & High Contrast Grey
Clean surface with a solution of mild dishwashing liquid diluted with warm
water. Sponge the surface, rinse with clear water and blot dry. Do not use
clean ing solvents or abrasives.
Viewing Surface Care & Maintenance
Glass Beaded
Clean with a very soft brush or cloth and care ful ly dust the surface. DO
NOT USE SOAP, WATER, SOLVENTS OR ABRASIVES. These substances
will damage a glass beaded viewing surface.
Caution
Read and understand these instructions; keep them for future reference.
Follow instructions carefully.
Care in both mounting and correct operation will mean long and satis-
factory service from your Draper screen.
Locate the screen where the audience can best see it, and where other
room fur nish ings permit.
Mount the screen so that the bottom of the picture, when screen is fully
extended, will be above the heads of viewers.
When raising screen, pull down and, while holding, allow for slow
retraction into the case to reduce risk of injury from falling screen.
Screen should be installed level (using a carpenter’s level).
Nothing should be fastened to screen dowel or viewing surface.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating prior to shipment.
  • Page 1 1

Draper 137052 Operating instructions

Category
Projection screens
Type
Operating instructions
This manual is also suitable for

Draper 137052 is a wall or ceiling-mounted projection screen designed to provide a clear and stable viewing surface for presentations, movies, or other visual content. It features a slow retraction mechanism to prevent injuries and a locking system to keep the screen in place when not in use. The screen's surface is easy to clean and maintain, with specific care instructions provided for different surface types like matt white, high contrast grey, and glass beaded. Additionally, the screen can be adjusted left or right to achieve the optimal viewing angle.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI