Ibiza Light DERBY-LAS Owner's manual

Page is loading ...

2

©Copyright LOTRONIC 2016 DERBY-LAS

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are

present and have been received in good condition. Notify the freight company immediately and retain packing

material for inspection if any parts appear to be damaged from shipping or the carton itself shows signs of

mishandling. Keep the carton and all packing materials. In the event that a fixture must be returned to the

factory, it is important that the fixture be returned in the original factory box and packing.

Safety Instructions

Please read these instructions carefully, they include important information about the installation, usage and

maintenance of this product.

• Please keep this User Guide for future reference. If you sell the unit to another user, be sure that he also

receives this instruction booklet.

• Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting

to is not higher than that stated on the decal or rear panel of the fixture.

• This product is intended for indoor use only!

• To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no flammable

materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least 1m from adjacent surfaces. Be sure

that no ventilation slots are blocked.

• Always disconnect from power source before servicing or replacing fuse and be sure to replace with same fuse

size and type.

• Maximum ambient temperature (Ta) is 104° F (40°C). Do not operate the fixture at temperatures higher than

this.

• In the event of a serious operating problem, stop using the unit immediately. Never try to repair the unit by

yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest

authorized technical assistance center. Always use the same type of spare parts.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

• DISCONNECT DEVICE: Where the MAINS plug or an appliance coupler is used as the disconnect device, the

disconnect device shall remain readily operable.

• The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a

similar qualified person.

GB

3

©Copyright LOTRONIC 2016 DERBY-LAS

Specifications

Voltage .................................................................................................................. 220-240V AC~ 50/60Hz

Consumption ...................................................................................................................................... 40W

Laser class .............................................................................................................................................. 3B

Laser diode ........................................................................... Red: 120mW 650nm; green: 30mW 532nm

LED source ...................................................................................................................................... 9 x 3W

LED colours ..................................... Red, Green, Blue, White, Warm White, Orange, Yellow, Purple, UV

Dimensions ................................................................................................................. 185 x 162 x 210mm

Weight ............................................................................................................................................. 1.48kg

Power supply, wire Connection

Use a dedicated plug to connect the LED light and power. Make sure the unit is connected to the appropriate

power supply.

Warning

Carry the lights only by the handle.

Features

The control panel features 4 buttons and a 4-digit LED display.

Operation

1) When power is on, the digital LED display works with red dots. When

a DMX signal is present, the dot will be shiny.

2) DMX address code setting: Press “MENU” button. When the digital LED displays d001-d512, press “UP” or

“Down” to set the address code. The code ranges from 001-512.

Button Specifications:

All Effects

Motor Speed

Autn



An01-An07



S.01-S.09

Derby effects

Motor Speed

Autp



Ap01-AP07



S.01-S.09

Laser effects

Motor Speed

AutF



AF01-AF04



S.01-S.09

Sound effect - Whole Unit

Sound Effect - Derby

Sound Effect - Laser

Sound



S.01-S.03



S0.4



S.05

SLAU



Slave

D001-d512



DMX

Connection of Signal Cable

You can use the 3-pin XLR cable to connect the OUT socket of the first light and the IN socket of the following

light. Connect all the lights as below:

4

©Copyright LOTRONIC 2016 DERBY-LAS

A DMX signal terminator is recommended on the last unit of the chain. DMX terminator is a XLR connector with

a 120Ω resistor between the pin 2 and pin 3 of the XLR connector

Remote Control:

ON/OFF

DMX Mode

LASER: LASER ON/OFF

AUTO MIX: Auto Mode with PAR-LASER Effects

SOUND MIX: Sound Mode with PAR-LASER Effects

R: Red Laser ON

LED / Auto Mode: Par Effects

LED / Sound Mode: Par Effects

G: Green Laser ON

LASER : Laser Auto Mode

LASER: Laser Sound Mode

RG:RG Laser ON

COLOR -/+ : Color & Speed slow /fast

LASER MOTOR: Motor slow/fast

SEN -/+: Sensitivity -/+

8 DMX Channels:

CH1

0-9

/

10-19

Effects of the Whole Unit

(An01-7)

20-29

30-39

40-49

50-59

60-69

70-79

80-89

Derby Effects

(Ap01-AP07)

90-99

100-109

110-119

120-129

130-139

140-149

150-159

Laser Effects

5

©Copyright LOTRONIC 2016 DERBY-LAS

160-169

(AF01-AF04)

170-179

180-189

190-199

Sound Effect

(Whole Unit)

(S.01-S.03)

200-209

210-219

220-229

S.04 Sound Effect (Derby)

230-255

S.05 Sound Effect (Laser)

CH2

0-9

/

10-255

Speed adjustable

CH3

0-255

Derby (Red, Blue, Warm White)

CH4

0-255

Derby (Orange, White, Yellow)

CH5

0-255

Derby (Green, Purple, UV)

CH6

0-255

Motor Speed

CH7

0-63

/

64-127

Red Laser

128-191

Green Laser

192-255

RG Laser

CH8

0-255

Laser Motor Speed

Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize

light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or

particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.

• Clean with soft cloth using normal glass cleaning fluid.

• Always dry the parts carefully.

• Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.

VII. Trouble-shooting

Problem

Solution

No display when power is on

1. Check if the power is correctly connected.

2. Check if the outlet is powered

Light is out of control

1. Check if the DMX address code is correctly set.

2. Check if the DMX cable is correctly connected.

The light is off after working for a while

1. Check if the sensor is soldered on the LED PCB

2. Check if the temperature is too high or not.

3. Check if Power supply is damaged.

The beam is dark

1. Check if the temperature is too high and cause a fast fade.

2. Check if there is too much dust on the surface of light.

This marking indicates that this product should not be disposed with other household wastes throughout

the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal,

recycle it responsibly to promote the sustainable reuse of material resources. To return your used device,

please use the return and collection systems or contact the retailer where the product was purchased. They can

take this product for environmental safe recycling.

Page is loading ...

GB

LASER FOR PROFESSIONAL USE ONLY

This laser complies with the international standards CEI60825/EN60825. It is meant exclusively for professional use.

Its installation and use should only be carried out by a skilled technician who is aware of the specific dangers of lasers.

REMINDER OF SAFETY INSTRUCTIONS

Lasers of class 3 and 4 are for outdoor use only.

Inside the public area, any laser shooting towards the audience is strictly forbidden except if a safety area of 5 m radius is

marked around the area to which the audience cannot get access.

The area called “public area” is defined by the space of 3m above the area occupied by the audience and a width of 2.5m around

this area. The public area must be clearly identified by signs on the ground.

Inside the public area only a scanning movement is allowed within the terms and conditions defined by the international

technical laser safety report.

The laser unit must be installed out of reach of the audience and at a minimum of 3m above the ground where the audience is

present or protected by a safety perimeter of 5m radius.

The laser unit must be installed in such a way that it can’t be moved under the effect of disruptions such as crowd movements,

vibrations or gusts of wind.

Installation and settings must comply with the regulations defined in the international laser safety report CEI / TR 60825-3

(March 2008).

F

LASER A USAGE EXCLUSIVEMENT PROFESSIONNEL

Ce laser est conforme aux normes CEI60825/EN60825, il est à usage exclusivement professionnel,

Son installation et utilisation doit être effectué exclusivement par un technicien compétent et formé

aux risques spécifiques des lasers.

RAPPEL DES PRECAUTIONS DE SECURITE

Les appareils à lasers de classe 3 et 4, sont utilisables exclusivement en plein air

A l'intérieur de la zone réservée au public, aucun " tir laser " n'est admis en direction du public, quelle que soit la classe du laser,

sauf si un périmètre d'exclusion du public de 5 mètres de rayon, matérialisé, est mis en place.

La zone dite " zone réservée au public " est définie par l'espace situé jusqu'à 3 mètres au-dessus de la surface occupée par le

public et sur une bande de 2, 5 mètres autour de cette dernière. La zone réservée au public est matérialisée au sol.

Dans la zone réservée au public, seul est admis un rayonnement par balayage effectué dans les conditions fixées par le rapport

technique international sur la sécurité des appareils à laser

L'appareil à laser est hors de portée du public et au minimum à 3 mètres au-dessus du sol accessible au public ou protégé par un

périmètre de sécurité de 5 mètres de rayon.

L'appareil laser doit être fixé/posé de telle manière qu'il ne puisse pas être déplacé sous l'effet de perturbations telles que des

mouvements de foule, des vibrations ou des rafales de vent.

L'installation et les réglages respectent les dispositions fixées par le rapport technique international sur la sécurité des appareils

à laser CEI / TR 60825-3 (mars 2008).

D

LASER FÜR AUSSCHLIESSLICH GEWERBLICHEN GEBRAUCH

Dieser Laser entspricht den Normen CEI60825/EN60825. Er ist ausschließlich für gewerblichen Einsatz erlaubt.

Die Installation und Bedienung dürfen nur von einem erfahrenen Techniker vorgenommen werden, der für die spezifischen

Gefahren von Laserstrahlen ausgebildet ist.

ERINNERUNG AN DIE SICHERHEITSVORSCHRIFTEN

Laser der Klassen 3 und 4 dürfen nur im Freien eingesetzt werden.

Innerhalb des öffentlichen Bereichs darf kein Laserstrahl in Richtung des Publikums abgegeben werden, egal um welche

Laserklasse es sich handelt, es sei denn, es wurde ein auf dem Boden klar abgegrenzter und vom Publikum unzugänglicher

Sicherheitsbereich von 5m eingerichtet.

Der sogenannte “öffentliche Bereich“ betrifft den Bereich von 3m über dem vom Publikum eingenommenen Bereich und eine

Breite von 2,5m um diesen Bereich herum. Der öffentliche Bereich muss klar auf dem Boden gekennzeichnet sein.

In diesem öffentlichen Bereich ist nur ein Scannen unter Einhaltung der im internationalen technischen Bericht über die

Sicherheit von Lasern festgelegten Bedingungen zugelassen.

Page is loading ...

Ibiza Light DERBY-LAS Owner's manual

Ibiza Light DERBY-LAS Owner's manual

in other languages

Related papers

Other documents