andrews Double Cool Operating Instructions & Safety Manual

Brand: andrews

Model: Double Cool

Type: Operating Instructions & Safety Manual

Click www.andrews-sykes.com

or Call Us Free 0800 211 611

Double Cool

Portable Air Conditioning

Operating Instructions

& Safety Guide

Do not lay electrical cables in wet / damp areas.

Do not move equipment whilst operating.

Do not pull equipment by its cable.

Cleaning and Maintenance

The Andrews Sykes range of evaporative air conditioners are designed to give

many years of trouble free operation. It is however important that the simple

regular maintenance described in this section is carried out.

Note: Isolate the unit from the power supply before carrying out any form of

maintenance.

At the end of each week

Clean side and back cooling pads and removed dust particles wit a vacuum

cleaner. Clean the outside body with a damp cloth.

At the end of each month

Place a sterilising tablet or a capful of sterilising liquid into a full reservoir and

operate the pump to circulate the sterilised water through the whole system. Drain

the water tank and clean any build up with a dam cloth. To gain access to the

water tank you will need to remove on or more panels.

At the end of summer season

Before storing the unit, drain the water tank and wipe down with a sterilising agent.

Remove the cooling pads and wash using a gentle spray. Then allow them to

completely dry before replacing.

General Safety

Keep children and animals away from air conditioning units. Never leave them

alone in a room where the units in use.

This equipment should only be used by a competent person who has read

and understood these instructions.

Never operate this equipment if you are ill, feeling tired or under the inﬂuence

of alcohol or drugs.

Keep the Air Conditioning vents clear of all obstructions.

Never put anything on top of the unit or block the air outlets.

Make sure equipment is switched off and unplugged after use. Never leave

switched on or unattended.

Located unit as to protect against accidental or malicious damage

Check condition of equipment before use. If unit is showing signs of damage

contact your supplier immediately.

Electrical Safety

Requires a standard earthed power supply 230v. An extension cable (a

minimum of 1.5mm three core earthed lead) may be used.

Extension leads must be fully uncoiled when being used.

Extension leads must be protected from any possibility or interference or

damage.

Andrews Sykes recommends the use of a power supply that is protected by

an RCD ( residual current operated device). This provides extra safety. Always

inspect the power supply cable and plug for damage before use.

Damaged plugs and powers supply cables must only be replaced by and

authorised repair agent.

Andrews evaporative air conditions are ﬁtted with thermal cutouts which stop

the unit if a pump or fan motor overheats. The cut-out automatically resets

once the motor has cooled.

This unit requires a 230 volt electrical supply. It plugs into a standard BS1363

domestic socket.

Always inspect plugs and leads for damage before plugging into the supply -

DO NOT USE IF ANY DAMAGE IS FOUND

Ensure cables are run as not to cause a hazard.

If an extension lead is used, ensure it is of the correct standard , and fully

uncoiled when being used.

Operating Instructions - Double Cool

Click www.andrews-sykes.com or Call Us Free 0800 211 611

Care of your Double Cool Dx

Do not add any chemicals, bleaches or agents to the water tank other than

sterilising tablets.

Do not place anything on top of the unit and don’t obstruct the air vents.

Do not remove the repositions the unit with water in the tank.

Do not remove any access panels when the unit is switched ON.

Always operate, transport and store the Double Cool Dx in an upright position.

Always inspect the unit before and use at regular intervals. If the unit is

damaged, do not use it. Have all necessary repairs carried out by an

authorised repair agent.

When not in use, store the unit with all controls set to OFF and with the water

thank fully drained, cleaned and sterilised

Setting up your Double Cool Dx

The DOUBLE COOL Dx model is designed to be placed on the base trolley

supplied and must be kept level to prevent over spill from the water tank. Place the

DOUBLE COOL Dx squarely onto the base trolley. Please note that the trolley is not

attached to the unit

To cool a room efﬁciently the DOUBLE COOL Dx requires a continuous supply of

fresh air and therefore should be positioned close to an open window or door to the

outside. It is also important to have another window or a door open for the warm

air to exit. Once positioned in the room, lock the casters to prevent the unit from

moving. Decide upon which method is best suited for ﬁlling the water tank.

There are two options, either direct ﬁlling by connections to a main water supply or

by manual ﬁlling via the manual water ﬁll inlet.

Direct Filling

Attach a suitable hose to the auto ﬁll water inlet connector using a worm drive clip.

Double check for sign of water leakage from the connection before connecting the

unit to the power supply. If in doubt, consult a qualiﬁed plumber.

There is a ﬂoat valve inside the water tank, which controls the water ﬂow as

necessary.

Manual Filling

CAUTION. Always switch OFF the unit and unplug from the power supply before

manually ﬁlling this machine. Mop up all the spillages before switching ON again.

Never handle plugs and electrical switches with wet hands.

To ﬁll the water tank, open the manual water ﬁll inlet and our up to 45 liters of fresh

clean water into the the tank.

The level of water in the tank is displayed on the water level indicator. During use,

the water level should be checked on a regular basis and topped up as necessary.

Never overﬁll this machine. DOUBLE COOL Dx is now ready to use.

Controls

With the unit in position and the water tank either ﬁlled manually or connected

to a main water supply, plug the unit into a suitable power supply and switch

the supply ON.

The unit can be operated as a cooler or simply as a fan.

To operate as a fan, full raise the water ﬂow lever then turn the ON/OFF/FAN

switch to the required fan speed setting.

There are three fan speeds available Low, Medium or High. When ﬁrst

switching ON, select Low and wait for the fan to reach normal running speed.

There are two controls for the direction of airﬂow.

The air ﬂow up/ down control lever is a manual control which directs the air

ﬂow vertically.

The air deﬂector control is a powered deﬂectors, which oscillates Horizontally

(side to side). When switched ON the deﬂectors move from left to right in a

sweeping motion, distributing air to a wider area.

If the air ﬂow is required in one direction only, switch the vertical louver swing

control to ON and when the air ﬂow is the right direction, switch the vertical

louver swing control OFF.

To run the unit in cool mode, operated the unit as described above and then

depres the water ﬂow lever.

When switching the unit OFF, full press down the water ﬂow lever and allow

the fan to run for approximately 10 minutes.

This enables the cooling pads to dry and will help eliminate the possibility of a

musty odor from the unit when next used.

1. Water ﬂow knob (Cool Knob)

2. Air ﬂow up / down control knob

3. Ar outlet grill

4. Power supply cable

5. ON/OFF and Fan speed control

6. Vertical Louver swing control

7. Auto ﬁll water inlet (Float valve)

8. Water level indicator

9. Manual water ﬁll inlet

10. Stand

11. Water tank reservoir

12. Drain plug

13. Holder pad

14. Power Indicator

andrews Double Cool Operating Instructions & Safety Manual

andrews Double Cool Operating Instructions & Safety Manual

andrews Double Cool Operating Instructions & Safety Manual

Related papers

Other documents