032R9791
032R9791
© Danfoss | DCS (az) | 2018.11
© Danfoss | DCS (az) | 2018.11
1
3
2
Danfoss
32F1011.20
Allen key 5 mm
Danfoss
32F1013.10
Danfoss
32F877.20
1
3
2
Remove strainer
from valve body
Dismount strainer
5 mm
allen key
Torque 6 Nm ± 1
Clean or replace strainer
and replace O-ring
5 mm allen key
4
5
6
Assemble strainer
Oil O-rings and place
strainer in valve
Mount the strainer
with screws
7
8
A
B
C
D
1
3
2
Danfoss
32F855.10
A
B
C
D
Remove ejector from valve body Replace complete ejector
Mount the ejector with screws
Oil O-rings and place ejector
= compressor oil
Allen key 5 mm
Allen key 5 mm
Allen key 5 mm
Torque 10 Nm ± 1
Allen key 5 mm
Torque 10 Nm ± 1
Danfoss
32F1012.10
A
B
C
DKRCC.PI.VM0.B3.02 | 1
DKRCC.PI.VM0.B3.02 | 4
Installation guide
Multi Ejector (Spareparts)
Type CTM 1, CTM 2, CTM 6
Service on ejector / O-rings
Remove ejector from
valve body
Replace complete ejector/
For service on O-rings:
replace O-rings A, B and C
Oil O-rings and place ejector
Tightening sequence
Allen key 5 mm
Torque 10 Nm ± 1
Mount the ejector with screws
Allen key 5 mm
© Danfoss | DCS (az) | 2018.11
© Danfoss | DCS (az) | 2018.11
1
3
2
4
Danfoss
32F1007.30
Allen key 5 mm
1
3
2
4
Danfoss
32F1007.30
Allen key 5 mm
Danfoss
32F1008.20
5
6
Danfoss
32F1008.20
5
6
Danfoss
32F897.10
A
B
C
D
Danfoss
32
F898.20
8
Allen key 5 mm
7
Danfoss
32F899.20
D
E
A
B
C
D
Danfoss
32F1000.11
Torque 6 mm screws: 10 Nm ± 1 Nm
Torque 6 mm screws: 10 Nm ± 1 Nm
Torque 8 mm screws: 27.5 Nm ± 2.5 Nm
Allen key 5 mm
Allen key 5 mm
Allen key 6 mm
Danfoss
32F1006.10
Torque 6 mm screws: 10 Nm ± 1 Nm
Torque 6 mm screws: 10 Nm ± 1 Nm
Allen key 5 mm
Allen key 5 mm
Allen key 5 mm
A
B
C
D
Torque 6 mm screws: 10 Nm ± 1 Nm
CTM 1 - CTM 2
CTM 6
DKRCC.PI.VM0.B3.02 | 3
DKRCC.PI.VM0.B3.02 | 2
Service on strainer
Remove strainer from valve body
Dismount strainer
Allen key
5 mm
Allen key 5 mm
Allen key 5 mm
Torque 6 Nm ± 1
Clean / replace strainer/
replace O-rings D and E
Mount strainer with screws
Assemble strainer
Oil O-rings and place strainer in valve
= compressor oil
Tighteninig sequence
Allen key 5 mm
Torque 10 Nm ± 1
Service on connectors
1. Remove connectors with O-rings
2. Replace O-rings and place new connectors
3. Mount new connectors with screws:
- 6 mm screws torque: 10 Nm ± 1 Nm
- 8 mm screws torque: 27.5 Nm ± 2.5 Nm
Tightening sequence
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Danfoss 032F5698 Installation guide
-
Danfoss Multi Ejector, type CTM 6 Installation guide
-
-
-
-
Danfoss Multi Ejector Solution, Type CTM 6 HP and LP User guide
-
-
Danfoss 180B3062 User guide
-
-
Danfoss 027F3022 Installation guide