Bosch 0 603 955 40J Owner's manual

Category
Cordless combi drills
Type
Owner's manual
Robert Bosch GmbH
Power Tools Division
70745 Leinfelden-Echterdingen
www.bosch-pt.com
1 609 929 M89 (2007.11) O / 104
PSR
12 | 14,4 | 18
de Originalbetriebsanleitung
en Original instructions
fr Notice originale
es Manual original
pt Manual original
it Istruzioni originali
nl Oorspronkelijke
gebruiksaanwijzing
da Original brugsanvisning
sv Bruksanvisning i original
no Original driftsinstruks
fi Alkuperäiset ohjeet
el Πρωτότυπο οδηγιών χρήσης
tr Orijinal işletme talimat
OBJ_DOKU-2370-003.fm Page 1 Monday, November 5, 2007 10:02 AM
1 609 929 M89 | (5.11.07) Bosch Power Tools
2 |
Deutsch. . . . . . . . . . . . . . . . . . . . . . . . . . . . Seite 4
English. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 12
Français. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 19
Español . . . . . . . . . . . . . . . . . . . . . . . . . . . Página 27
Português . . . . . . . . . . . . . . . . . . . . . . . . . Página 36
Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . Pagina 44
Nederlands . . . . . . . . . . . . . . . . . . . . . . . . Pagina 52
Dansk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Side 60
Svenska. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sida 67
Norsk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Side 74
Suomi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sivu 81
Ελληνικά . . . . . . . . . . . . . . . . . . . . . . . . . . . Σελίδα 88
Türkçe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sayfa 96
OBJ_BUCH-149-003.book Page 2 Monday, November 5, 2007 10:04 AM
| 3
Bosch Power Tools 1 609 929 M89 | (5.11.07)
PSR 18
BA
8
2
1
14
8
12
12
4
3
2
6
7
131211
9
10
5
1
8
OBJ_BUCH-149-003.book Page 3 Monday, November 5, 2007 10:04 AM
1 609 929 M89 | (5.11.07) Bosch Power Tools
8 | Deutsch
Technische Daten
Konformitätserklärung
Wir erklären in alleiniger Verantwortung, dass
das unter „Technische Daten“ beschriebene Pro-
dukt mit den folgenden Normen oder normativen
Dokumenten übereinstimmt: EN 60745 gemäß
den Bestimmungen der Richtlinien
2004/108/EG, 98/37/EG (bis 28.12.2009),
2006/42/EG (ab 29.12.2009).
Technische Unterlagen bei:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
18.09.2007, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Montage
Akku laden
Ein neuer oder längere Zeit nicht verwendeter
Akku bringt erst nach ca. 5 Lade- und Entladezyk-
len seine volle Leistung.
Zur Entnahme des Akkus 10 drücken Sie die Ent-
riegelungstasten 9 und ziehen den Akku nach un-
ten aus dem Elektrowerkzeug. Wenden Sie dabei
keine Gewalt an.
Der Akku ist mit einer NTC-Temperaturüberwa-
chung ausgestattet, welche ein Aufladen nur im
Temperaturbereich zwischen 0 °C und 45 °C zu-
lässt. Dadurch wird eine hohe Akku-Lebensdauer
erreicht.
Eine wesentlich verkürzte Betriebszeit nach der
Aufladung zeigt an, dass der Akku verbraucht ist
und ersetzt werden muss.
Beachten Sie die Hinweise zur Entsorgung.
Akku-Bohrschrauber PSR 12 PSR 14,4 PSR 18
Sachnummer
3 603 J55 5.. 3 603 J55 4.. 3 603 J55 3..
Nennspannung
V= 12 14,4 18
Leerlaufdrehzahl
min
-1
0700 0700 0700
max. Drehmoment harter/weicher
Schraubfall nach ISO 5393
Nm 26/11 28/12 30/13
max. Schrauben-
Ø mm 8 88
max. Bohr-
Ø
–Stahl
–Holz
mm
mm
10
20
10
25
10
28
Gewicht entsprechend EPTA-Procedure
01/2003
kg 1,4 1,5 1,7
Bitte beachten Sie die Sachnummer auf dem Typenschild Ihres Elektrowerkzeugs. Die Handelsbezeichnungen einzelner
Elektrowerkzeuge können variieren.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
OBJ_BUCH-149-003.book Page 8 Monday, November 5, 2007 10:04 AM
1 609 929 M89 | (5.11.07) Bosch Power Tools
12 | English
en
General Power Tool Safety
Warnings
Read all safety warnings and all
instructions. Failure to follow the
warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to
your mains-operated (corded) power tool or bat-
tery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Clut-
tered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools. Unmodified
plugs and matching outlets will reduce risk
of electric shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes, radia-
tors, ranges and refrigerators. There is an
increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool
will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat,
oil, sharp edges and moving parts. Dam-
aged or entangled cords increase the risk
of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for out-
door use. Use of a cord suitable for out-
door use reduces the risk of electric shock.
f) If operating a power tool in a damp loca-
tion is unavoidable, use a residual current
device (RCD) protected supply. Use of an
RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment
of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Al-
ways wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protec-
tion used for appropriate conditions will
reduce personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or bat-
tery pack, picking up or carrying the tool.
Carrying power tools with your finger on
the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench be-
fore turning the power tool on. A wrench
or a key left attached to a rotating part of
the power tool may result in personal inju-
ry.
e) Do not overreach. Keep proper footing
and balance at all times. This enables bet-
ter control of the power tool in unexpected
situations.
f) Dress properly. Do not wear loose cloth-
ing or jewellery. Keep your hair, clothing
and gloves away from moving parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
WARNING
OBJ_BUCH-149-003.book Page 12 Monday, November 5, 2007 10:04 AM
English | 13
Bosch Power Tools 1 609 929 M89 | (5.11.07)
g) If devices are provided for the connection
of dust extraction and collection facili-
ties, ensure these are connected and
properly used. Use of dust collection can
reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the cor-
rect power tool for your application. The
correct power tool will do the job better
and safer at the rate for which it was de-
signed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjust-
ments, changing accessories, or storing
power tools. Such preventive safety meas-
ures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfa-
miliar with the power tool or these in-
structions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalign-
ment or binding of moving parts, break-
age of parts and any other condition that
may affect the power tool’s operation. If
damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Prop-
erly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and tool
bits etc. in accordance with these instruc-
tions, taking into account the working
conditions and the work to be performed.
Use of the power tool for operations differ-
ent from those intended could result in a
hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with anoth-
er battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any oth-
er battery packs may create a risk of injury
and fire.
c) When battery pack is not in use, keep it
away from other metal objects, like paper
clips, coins, keys, nails, screws or other
small metal objects, that can make a con-
nection from one terminal to another.
Shorting the battery terminals together
may cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6) Service
a) Have your power tool serviced by a quali-
fied repair person using only identical re-
placement parts. This will ensure that the
safety of the power tool is maintained.
Machine-specific
Safety Warnings
f Use appropriate detectors to determine if
utility lines are hidden in the work area or
call the local utility company for assistance.
Contact with electric lines can lead to fire and
electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes
property damage or may cause an electric
shock.
f Switch off the power tool immediately when
the tool insert jams. Be prepared for high re-
action torque that can cause kickback. The
tool insert jams when:
— the power tool is subject to overload or
— it becomes wedged in the workpiece.
OBJ_BUCH-149-003.book Page 13 Monday, November 5, 2007 10:04 AM
1 609 929 M89 | (5.11.07) Bosch Power Tools
14 | English
f Hold power tool by the insulated gripping
surfaces, when performing an operation
where the cutting tool may run into hidden
wiring. Contact with a “live” wire will make
exposed metal parts of the tool “live” and
shock the operator.
f Hold the machine with a firm grip. High reac-
tion torque can briefly occur while driving in
and loosening screws.
f Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
secure than by hand.
f Keep your workplace clean. Blends of mate-
rials are particularly dangerous. Dust from
light alloys can burn or explode.
f Always wait until the machine has come to a
complete stop before placing it down. The
tool insert can jam and lead to loss of control
over the power tool.
f Avoid unintentional switching on. Ensure the
On/Off switch is in the off position before in-
serting battery pack. Carrying the power tool
with your finger on the On/Off switch or in-
serting the battery pack into power tools that
have the switch on invites accidents.
f Do not open the battery. Danger of short-
circuiting.
Protect the battery against heat, e. g.,
also against continuous sun irradiation
and fire. There is danger of explosion.
Functional Description
Read all safety warnings and all in-
structions. Failure to follow the
warnings and instructions may result
in electric shock, fire and/or serious
injury.
Intended Use
The machine is intended for driving in and loos-
ening screws as well as for drilling in wood, met-
al, ceramic and plastic.
Product Features
The numbering of the product features refers to
the illustration of the machine on the graphics
page.
1 Keyless chuck
2 Front sleeve
3 Rear sleeve
4 Torque preselection ring
5 Indicator for right rotation
6 Indicator for left rotation
7 Soft grip
8 Screwdriver bit*
9 Battery unlocking button
10 Battery
11 “Power Light”
12 Rotational direction switch
13 On/Off switch
14 Universal bit holder*
*The accessories illustrated or described are not in-
cluded as standard delivery.
Noise/Vibration Information
Measured values determined according to
EN 60745.
Typically the A-weighted sound pressure level of
the product is 75 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed
80 dB(A).
Wear hearing protection!
Vibration total values (triax vector sum) deter-
mined according to EN 60745:
Drilling into metal: Vibration emission value
a
h
<2.5 m/s
2
, Uncertainty K=1.5 m/s
2
,
Screwdriving: Vibration emission value
a
h
<2.5 m/s
2
, Uncertainty K=1.5 m/s
2
.
The vibration emission level given in this informa-
tion sheet has been measured in accordance
with a standardised test given in EN 60745 and
may be used to compare one tool with another. It
may be used for a preliminary assessment of ex-
posure.
OBJ_BUCH-149-003.book Page 14 Monday, November 5, 2007 10:04 AM
English | 15
Bosch Power Tools 1 609 929 M89 | (5.11.07)
The declared vibration emission level represents
the main applications of the tool. However if the
tool is used for different applications, with differ-
ent accessories or poorly maintained, the vibra-
tion emission may differ. This may significantly
increase the exposure level over the total work-
ing period.
An estimation of the level of exposure to vibra-
tion should also take into account the times
when the tool is switched off or when it is run-
ning but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as:
maintain the tool and the accessories, keep the
hands warm, organisation of work patterns.
Technical Data
Declaration of Conformity
We declare under our sole responsibility that the
product described under “Technical Data” is in
conformity with the following standards or
standardization documents: EN 60745 according
to the provisions of the directives 2004/108/EC,
98/37/EC (until Dec. 28, 2009), 2006/42/EC
(from Dec. 29, 2009 on).
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
18.09.2007, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Assembly
Battery Charging
A battery that is new or has not been used for a
longer period does not develop its full capacity
until after approx. 5 charging/discharging cycles.
To remove the battery 10 press the unlocking
buttons 9 and pull out the battery downwards.
Do not exert any force.
The battery is equipped with a NTC temperature
control which allows charging only within a tem-
perature range of between 0 °C and 45 °C. A long
battery service life is achieved in this manner.
A significantly reduced working period after
charging indicates that the battery is used and
must be replaced.
Observe the notes for disposal.
Cordless Screwdriver PSR 12 PSR 14,4 PSR 18
Article number
3 603 J55 5.. 3 603 J55 4.. 3 603 J55 3..
Rated voltage
V= 12 14,4 18
No-load speed
rpm 0700 0700 0700
Max. torque for hard/soft screwdriving
application according to ISO 5393
Nm 26/11 28/12 30/13
Max. screw dia.
mm 8 88
Max. drilling dia.
– Steel
–Wood
mm
mm
10
20
10
25
10
28
Weight according to EPTA-Procedure
01/2003
kg 1.4 1.5 1.7
Please observe the article number on the type plate of your machine. The trade names of the individual machines may
vary.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
OBJ_BUCH-149-003.book Page 15 Monday, November 5, 2007 10:04 AM
1 609 929 M89 | (5.11.07) Bosch Power Tools
16 | English
Changing the Tool (see figure A)
f Before any work on the machine (e. g., main-
tenance, tool change, etc.) as well as during
transport and storage, set the rotational di-
rection switch to the centre position. Unin-
tentional actuation of the On/Off switch can
lead to injuries.
Hold the rear sleeve 3 of the keyless chuck 1 tight
and turn the front sleeve 2 in rotation direction
n, until the tool can be inserted. Insert the tool.
Hold the rear sleeve 3 of the keyless chuck 1 tight
and firmly tighten the front sleeve 2 by hand in
rotation direction o, until the locking action
(click) is heard. The drill chuck is locked auto-
matically.
The locking is released again to remove the tool
when the front sleeve 2 is turned in the opposite
direction.
Replacing the Drill Chuck
For machines without spindle lock, the drill
chuck must be replaced through an authorized
after-sales service agent for Bosch power tools.
The drill chuck must be tightened with a
tightening torque of approx. 3035 Nm.
Dust/Chip Extraction
f Dusts from materials such as lead-containing
coatings, some wood types, minerals and
metal can be harmful to one’s health. Touch-
ing or breathing-in the dusts can cause aller-
gic reactions and/or lead to respiratory infec-
tions of the user or bystanders.
Certain dusts, such as oak or beech dust, are
considered as carcinogenic, especially in con-
nection with wood-treatment additives (chro-
mate, wood preservative). Materials contain-
ing asbestos may only be worked by
specialists.
Use dust extraction whenever possible.
Provide for good ventilation of the working
place.
It is recommended to wear a P2 filter-class
respirator.
Observe the relevant regulations in your coun-
try for the materials to be worked.
Operation
Starting Operation
Inserting the Battery
f Use only original Bosch O-pack batteries
with the voltage given on the type plate of
your machine. The use of other batteries can
lead to injuries and danger of fire.
Set the rotational direction switch 12 to the cen-
tre position in order to avoid unintentional start-
ing. Insert the charged battery 10 into the handle
so that it can be felt to engage and faces flush
against the handle.
Reversing the Rotational Direction
(see figure B)
The rotational direction switch 12 is used to re-
verse the rotational direction of the machine.
However, this is not possible with the On/Off
switch 13 actuated.
Right Rotation: For drilling and driving in screws,
push the rotational direction switch 12 left to the
stop.
The indicator for right rotation 5 lights up
when the On/Off switch 13 is actuated.
Left Rotation: For loosening or unscrewing
screws, push the rotational direction switch 12
right to the stop.
The indicator for left rotation 6 lights up
when the On/Off switch 13 is actuated.
Setting the Torque
The required torque can be preselected in 10
steps with the torque preselection ring 4. With
the correct setting, the insert tool is stopped as
soon as the screw is screwed flush into the ma-
terial or when the set torque is reached.
Select a higher setting when driving out screws,
or set to the symbol “Drilling”.
Drilling
The safety clutch is deactivated in the “Drilling”
position.
OBJ_BUCH-149-003.book Page 16 Monday, November 5, 2007 10:04 AM
English | 17
Bosch Power Tools 1 609 929 M89 | (5.11.07)
Switching On and Off
To start the machine, press the On/Off switch 13
and keep it depressed.
The power light 11 lights up when the On/Off
switch 13 is halfway or fully depressed, and ena-
bles illumination of the screwing location in unfa-
vourable light conditions.
To switch off the machine, release the On/Off
switch 13.
Adjusting the Speed
The speed of the switched on power tool can be
variably adjusted, depending on how far the
On/Off switch 13 is pressed.
Light pressure on the On/Off switch 13 results in
a low rotational speed. Further pressure on the
switch results in an increase in speed.
Run-on Brake
When the On/Off switch 13 is released, the
chuck brakes to a stop, thus preventing the run-
on of the tool.
When driving in screws, wait until the screw is
screwed in flush with the material and then re-
lease the On/Off switch 13. By doing so, the head
of the screw does not penetrate into the materi-
al.
Working Advice
f Apply the power tool to the screw only when
it is switched off. Rotating tool inserts can
slip off.
Soft Grip
The gripping surface (soft grip) 7 reduces the
danger of slipping and thereby improves the grip
on the machine and the handling.
At the same time, the rubber coating achieves a
vibration-reducing effect.
Tips
After longer periods of working at low speed, al-
low the machine to cool down by running it for
approx. 3 minutes at maximum speed with no
load.
For drilling in metal, use only perfectly sharp-
ened HSS drill bits (HSS=high-speed steel). The
appropriate quality is guaranteed by the Bosch
accessories program.
Before screwing larger, longer screws into hard
materials, it is advisable to predrill a pilot hole
with the core diameter of the thread to approx.
2
/
3
of the screw length.
Maintenance and Service
Maintenance and Cleaning
f Before any work on the machine (e. g., main-
tenance, tool change, etc.) as well as during
transport and storage, set the rotational di-
rection switch to the centre position. Unin-
tentional actuation of the On/Off switch can
lead to injuries.
f For safe and proper working, always keep
the machine and ventilation slots clean.
If the machine should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
centre for Bosch power tools.
In all correspondence and spare parts order,
please always include the 10-digit article number
given on the type plate of the machine.
OBJ_BUCH-149-003.book Page 17 Monday, November 5, 2007 10:04 AM
1 609 929 M89 | (5.11.07) Bosch Power Tools
18 | English
After-sales service and customer
assistance
Our after-sales service responds to your ques-
tions concerning maintenance and repair of your
product as well as spare parts. Exploded views
and information on spare parts can also be found
under:
www.bosch-pt.com
Our customer consultants answer your questions
concerning best buy, application and adjustment
of products and accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: SPT-Tec[email protected]sch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: +61 (01300) 307 044
Fax: + 61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au
Disposal
The machine, accessories and packaging should
be sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into
household waste!
According the European Guideline
2002/96/EC for Waste Electrical
and Electronic Equipment and its
implementation into national right,
power tools that are no longer usable must be
collected separately and disposed of in an envi-
ronmentally correct manner.
Battery packs/batteries:
Ni-Cd: Nickel cadmium
Warning: These battery packs contain cadmium,
a highly toxic heavy metal.
Ni-MH: Nickel metal hydride
Do not dispose of battery packs/batteries into
household waste, fire or water. Battery
packs/batteries should be collected, recycled or
disposed of in an environmental-friendly manner.
Only for EC countries:
Defective or dead out battery packs/batteries
must be recycled according the guideline
91/157/EEC.
Batteries no longer suitable for use can be
directly returned at:
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: SPT-Technical.de@de.bosch.com
Subject to change without notice.
OBJ_BUCH-149-003.book Page 18 Monday, November 5, 2007 10:04 AM
Français | 23
Bosch Power Tools 1 609 929 M89 | (5.11.07)
Caractéristiques techniques
Déclaration de conformité
Nous déclarons sous notre propre responsabilité
que le produit décrit sous « Caractéristiques
techniques » est en conformité avec les normes
ou documents normatifs suivants : EN 60745
conformément aux termes des réglementations
2004/108/CE, 98/37/CE (jusqu’au 28.12.2009),
2006/42/CE (à partir du 29.12.2009).
Dossier technique auprès de :
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
18.09.2007, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Montage
Charger l’accu
Un accu neuf ou un accu qui n’a pas été utilisé
pour une période assez longue n’atteint sa pleine
puissance qu’après environ cinq cycles de charge
et de décharge.
Pour sortir l’accu 10 appuyer sur les touches de
déverrouillage 9 et enlever l’accu de l’outil élec-
troportatif en tirant vers le bas. Ne pas appliquer
de la force.
L’accu est équippé d’une surveillange NTC de
température qui ne permet de charger l’accu que
dans la plage de température entre 0 °C et 45 °C.
La durée de vie de l’accu s’en trouve augmentée.
Si le temps de service de l’accu se raccourcit
considérablement après les recharges effec-
tuées, cela signifie que l’accu est usagé et qu’il
doit être remplacé.
Respectez les indications concernant l’élimina-
tion.
Perceuse-visseuse sans fil PSR 12 PSR 14,4 PSR 18
N° d’article
3 603 J55 5.. 3 603 J55 4.. 3 603 J55 3..
Tension nominale
V= 12 14,4 18
Vitesse de rotation en marche à vide
tr/min 0700 0700 0700
Couple max. vissage dur/tendre suivant
ISO 5393
Nm 26/11 28/12 30/13
Ø max. de vis mm 8 88
Ø perçage max.
–Acier
–Bois
mm
mm
10
20
10
25
10
28
Poids suivant EPTA-Procédure 01/2003
kg 1,4 1,5 1,7
Respectez impérativement le numéro d’article se trouvant sur la plaque signalétique de l’outil électroportatif. Les dé-
signations commerciales des différents outils électroportatifs peuvent varier.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
OBJ_BUCH-149-003.book Page 23 Monday, November 5, 2007 10:04 AM
Español | 31
Bosch Power Tools 1 609 929 M89 | (5.11.07)
Datos técnicos
Declaración de conformidad
Declaramos bajo nuestra responsabilidad, que el
producto descrito bajo “Datos técnicos” está en
conformidad con las normas o documentos nor-
malizados siguientes: EN 60745 de acuerdo con
las regulaciones 2004/108/CE, 98/37/CE (hasta
el 28.12.2009), 2006/42/CE (a partir del
29.12.2009).
Expediente técnico en:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
18.09.2007, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Montaje
Carga del acumulador
Un acumulador nuevo, o no utilizado durante mu-
cho tiempo, únicamente alcanza su plena poten-
cia después de haber estado sometido a aprox. 5
ciclos de carga y descarga.
Para extraer el acumulador 10 pulsar los botones
dee extracción 9 y sacar hacia abajo el acumula-
dor de la herramienta eléctrica. Proceder sin
brusquedad.
El acumulador viene equipado con un sensor de
temperatura NTC que solamente admite su recar-
ga dentro del margen de temperatura entre 0 °C
y 45 °C. De esta manera se alcanza un larga vida
útil del acumulador.
Si después de una recarga, el tiempo de funcio-
namiento del acumulador fuese muy reducido,
ello es señal de que éste está agotado y deberá
sustituirse.
Observe las indicaciones referentes a la elimina-
ción.
Atornilladora taladradora accionada
por acumulador
PSR 12 PSR 14,4 PSR 18
Nº de artículo
3 603 J55 5.. 3 603 J55 4.. 3 603 J55 3..
Tensión nominal
V= 12 14,4 18
Revoluciones en vacío
min
-1
0700 0700 0700
Par de giro máx. en unión atornillada
rígida/blanda según ISO 5393
Nm 26/11 28/12 30/13
Ø máx. de tornillos mm 8 88
Ø máx. de perforación
–Acero
– Madera
mm
mm
10
20
10
25
10
28
Peso según EPTA-Procedure 01/2003
kg 1,4 1,5 1,7
Preste atención al nº de artículo en la placa de características de su aparato, ya que las denominaciones comerciales
de algunos aparatos pueden variar.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
OBJ_BUCH-149-003.book Page 31 Monday, November 5, 2007 10:04 AM
1 609 929 M89 | (5.11.07) Bosch Power Tools
34 | Español
Si a pesar de los esmerados procesos de fabrica-
ción y control, la herramienta eléctrica llegase a
averiarse, la reparación deberá encargarse a un
servicio técnico autorizado para herramientas
eléctricas Bosch.
Para cualquier consulta o pedido de piezas de re-
puesto es imprescindible indicar el nº de artículo
de 10 dígitos que figura en la placa de caracterís-
ticas de la herramienta eléctrica.
Servicio técnico y atención al cliente
El servicio técnico le asesorará en las consultas
que pueda Ud. tener sobre la reparación y man-
tenimiento de su producto, así como sobre pie-
zas de recambio. Los dibujos de despiece e infor-
maciones sobre las piezas de recambio las podrá
obtener también en internet bajo:
www.bosch-pt.com
Nuestro equipo de asesores técnicos le orientará
gustosamente en cuanto a la adquisición, aplica-
ción y ajuste de los productos y accesorios.
España
Robert Bosch España, S.A.
Departamento de ventas
Herramientas Eléctricas
C/Hermanos García Noblejas, 19
28037 Madrid
Tel. Asesoramiento al cliente:
+34 (0901) 11 66 97
Fax: +34 (091) 327 98 63
Venezuela
Robert Bosch S.A.
Final Calle Vargas. Edf. Centro Berimer P.B.
Boleita Norte
Caracas 107
Tel.: +58 (02) 207 45 11
México
Robert Bosch S.A. de C.V.
Tel. Interior: +52 (01) 800 627 1286
Tel. D.F.: +52 (01) 52 84 30 62
E-Mail: arturo.fer[email protected]
Argentina
Robert Bosch Argentina S.A.
Av. Córdoba 5160
C1414BAW Ciudad Autonoma de Buenos Aires
Atencion al Cliente
Tel.: +54 (0810) 555 2020
Perú
Autorex Peruana S.A.
República de Panamá 4045,
Lima 34
Tel.: +51 (01) 475-5453
Chile
EMASA S.A.
Irarrázaval 259 – Ñuñoa
Santiago
Tel.: +56 (02) 520 3100
Eliminación
Recomendamos que las herramientas eléctricas,
accesorios y embalajes sean sometidos a un pro-
ceso de recuperación que respete el medio am-
biente.
Sólo para los países de la UE:
¡No arroje las herramientas eléctri-
cas a la basura!
Conforme a la Directriz Europea
2002/96/CE sobre aparatos eléc-
tricos y electrónicos inservibles,
tras su transposición en ley nacio-
nal, deberán acumularse por separado las herra-
mientas eléctricas para ser sometidas a un reci-
claje ecológico.
OBJ_BUCH-149-003.book Page 34 Monday, November 5, 2007 10:04 AM
1 609 929 M89 | (5.11.07) Bosch Power Tools
40 | Português
Dados técnicos
Declaração de conformidade
Declaramos sob nossa exclusiva responsabilida-
de que o produto descrito em “Dados técnicos”
cumpre as seguintes normas ou documentos nor-
mativos: EN 60745 conforme as disposições das
directivas 2004/108/CE, 98/37/CE (até
28.12.2009), 2006/42/CE (a partir de
29.12.2009).
Processo técnico em:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
18.09.2007, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Montagem
Carregar o acumulador
Um acumulador novo ou não utilizado durante
muito tempo, só desenvolve a sua completa po-
tência após aprox. 5 ciclos de carga e descarga.
Para retirar o acumulador 10, pressionar as te-
clas de destravamento 9 e puxar o acumulador
da ferramenta eléctrica por baixo. Não empregar
força.
O acumulador está equipado com uma monitori-
zação de temperatura NTC, que só permite uma
carga na faixa de temperatura entre 0 °C e 45 °C.
Desta forma é alcançada uma alta vida útil do
acumulador.
Um período de funcionamento reduzido após o
carregamento, indica que o acumulador está gas-
to e que deve ser substituido.
Observar a indicação sobre a eliminação de for-
ma ecológica.
Berbequim-aparafusador sem fio PSR 12 PSR 14,4 PSR 18
N° do produto
3 603 J55 5.. 3 603 J55 4.. 3 603 J55 3..
Tensão nominal
V= 12 14,4 18
N° de rotações em ponto morto
min
-1
0700 0700 0700
Máx. binário de aparafusamento
duro/macio conforme ISO 5393
Nm 26/11 28/12 30/13
máx.
Ø de aparafusamento mm 8 88
máx.
Ø de perfuração
–Aço
–Madeira
mm
mm
10
20
10
25
10
28
Peso conforme EPTA-Procedure
01/2003
kg 1,4 1,5 1,7
Observar o número de produto na placa de características da sua ferramenta eléctrica. A designação comercial das
ferramentas eléctricas individuais pode variar.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
OBJ_BUCH-149-003.book Page 40 Monday, November 5, 2007 10:04 AM
1 609 929 M89 | (5.11.07) Bosch Power Tools
48 | Italiano
Per una valutazione precisa della sollecitazione
da vibrazioni bisognerebbe considerare anche i
tempi in cui l’apparecchio è spento oppure è ac-
ceso ma non è utilizzato effettivamente. Questo
può ridurre chiaramente la sollecitazione da vi-
brazioni per l’intero periodo operativo.
Adottare misure di sicurezza supplementari per
la protezione dell’operatore dall’effetto delle vi-
brazioni come p. es.: manutenzione dell’elettrou-
tensile e degli accessori, mani calde, organizza-
zione dello svolgimento del lavoro.
Dati tecnici
Dichiarazione di conformità
Assumendone la piena responsabilità, dichiaria-
mo che il prodotto descritto nei «Dati tecnici» è
conforme alle seguenti normative ed ai relativi
documenti: EN 60745 in base alle prescrizioni
delle direttive 2004/108/CE, 98/37/CE (fino al
28.12.2009), 2006/42/CE (a partire dal
29.12.2009).
Fascicolo tecnico presso:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
18.09.2007, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Montaggio
Caricare la batteria
Una batteria che non sia stata utilizzata per un
lungo periodo di tempo arriva a portare la sua
piena prestazione solo dopo ca. 5 cicli di ricarica
e scarica.
Per togliere la batteria 10 premere i tasti di
sbloccaggio 9 ed estrarre verso il basso la batte-
ria dall’elettroutensile. Così facendo, non eserci-
tare forza eccessiva.
La batteria ricaricabile è dotata di un sensore NTC
per il controllo della temperatura che permette ope-
razioni di ricarica solo entro un campo di tempera-
tura tra 0 °C e 45 °C. In questo modo si permette di
raggiungere una lunga durata della batteria.
Una sensibile riduzione della durata del funziona-
mento dopo l’operazione di ricarica sta ad indicare
che la batteria ricaricabile dovrà essere sostituita.
Si prega di attenersi alle indicazioni relative allo
smaltimento.
Cacciaviti/avvitatore a batteria PSR 12 PSR 14,4 PSR 18
Codice prodotto
3 603 J55 5.. 3 603 J55 4.. 3 603 J55 3..
Tensione nominale
V= 12 14,4 18
Numero di giri a vuoto
min
-1
0700 0700 0700
Mass. momento di coppia avvitamento
di giunti rigidi/elastici conforme alla
norma ISO 5393
Nm 26/11 28/12 30/13
Diam. max. delle viti
mm 8 88
Diametro max. foratura
– Acciaio
– Legname
mm
mm
10
20
10
25
10
28
Peso in funzione della EPTA-Procedure
01/2003
kg 1,4 1,5 1,7
Si prega di tenere presente il codice prodotto applicato sulla targhetta di costruzione del Vostro elettroutensile. Le
descrizioni commerciali di singoli elettroutensili possono variare.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
OBJ_BUCH-149-003.book Page 48 Monday, November 5, 2007 10:04 AM
1 609 929 M89 | (5.11.07) Bosch Power Tools
56 | Nederlands
Technische gegevens
Conformiteitsverklaring
Wij verklaren als alleen verantwoordelijke dat het
onder „Technische gegevens” beschreven pro-
duct voldoet aan de volgende normen en norma-
tieve documenten: EN 60745 volgens de bepalin-
gen van de richtlijnen 2004/108/EG, 98/37/EG
(tot 28-12-2009) en 2006/42/EG (vanaf
29-12-2009).
Technisch dossier bij:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
18.09.2007, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Montage
Accu opladen
Een nieuwe of lang niet gebruikte accu levert pas
na ca. vijf oplaad- en ontlaadcycli zijn volledige
capaciteit.
Als u de accu 10 wilt verwijderen, drukt u op de
ontgrendelingsknoppen 9 en trekt u de accu naar
beneden uit het elektrische gereedschap. For-
ceer daarbij niet.
De accu is voorzien van een thermische beveili-
ging (NTC) die opladen alleen in het tempera-
tuurbereik tussen 0 °C en 45 °C toelaat. Daar-
door wordt een lange levensduur van de accu
bereikt.
Een duidelijk kortere gebruiksduur na het opla-
den duidt erop dat de accu versleten is en moet
worden vervangen.
Neem de voorschriften ten aanzien van de afval-
verwijdering in acht.
Accuboorschroevendraaier PSR 12 PSR 14,4 PSR 18
Zaaknummer
3 603 J55 5.. 3 603 J55 4.. 3 603 J55 3..
Nominale spanning
V= 12 14,4 18
Onbelast toerental
min
-1
0700 0700 0700
Max. draaimoment harde/flexibele
schroefverbinding volgens ISO 5393
Nm 26/11 28/12 30/13
Max. schroef-
Ø mm 8 88
Max. boor-
Ø
– Staal
–Hout
mm
mm
10
20
10
25
10
28
Gewicht volgens EPTA-Procedure
01/2003
kg 1,4 1,5 1,7
Let op het zaaknummer op het typeplaatje van het elektrische gereedschap. De handelsbenamingen van sommige elek-
trische gereedschappen kunnen afwijken.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
OBJ_BUCH-149-003.book Page 56 Monday, November 5, 2007 10:04 AM
Nederlands | 59
Bosch Power Tools 1 609 929 M89 | (5.11.07)
Mocht het elektrische gereedschap ondanks
zorgvuldige fabricage- en testmethoden toch de-
fect raken, dient de reparatie te worden uitge-
voerd door een erkende klantenservice voor
Bosch elektrische gereedschappen.
Vermeld bij vragen en bestellingen van vervan-
gingsonderdelen altijd het uit tien cijfers be-
staande zaaknummer volgens het typeplaatje van
het elektrische gereedschap.
Klantenservice en advies
Onze klantenservice beantwoordt uw vragen
over reparatie en onderhoud van uw product en
over vervangingsonderdelen. Explosietekeningen
en informatie over vervangingsonderdelen vindt
u ook op:
www.bosch-pt.com
De medewerkers van onze klantenservice advise-
ren u graag bij vragen over de aankoop, het ge-
bruik en de instelling van producten en toebeho-
ren.
Nederland
Tel.: +31 (076) 579 54 54
Fax: +31 (076) 579 54 94
België en Luxemburg
Tel.: +32 (070) 22 55 65
Fax: +32 (070) 22 55 75
Afvalverwijdering
Elektrische gereedschappen, toebehoren en ver-
pakkingen moeten op een voor het milieu verant-
woorde wijze worden hergebruikt.
Alleen voor landen van de EU:
Gooi elektrische gereedschappen
niet bij het huisvuil.
Volgens de Europese richtlijn
2002/96/EG over elektrische en
elektronische oude apparaten en
de omzetting van de richtlijn in na-
tionaal recht moeten niet meer bruikbare elektri-
sche gereedschappen apart worden ingezameld
en op een voor het milieu verantwoorde wijze
worden hergebruikt.
Accu’s en batterijen:
Ni-Cd: Nikkelcadmium
Let op: deze accu’s bevatten cadmium, een zeer
giftig zwaar metaal.
Ni-MH: Nikkelmetaalhydride
Gooi accu’s of batterijen niet bij het huisvuil en
evenmin in het vuur of het water. Accu’s en bat-
terijen moeten worden ingezameld, gerecycled
of op een voor het milieu verantwoorde wijze
worden afgevoerd.
Alleen voor landen van de EU:
Volgens richtlijn 91/157/EEG moeten defecte of
versleten accu’s en batterijen worden gerecy-
cled.
Wijzigingen voorbehouden.
OBJ_BUCH-149-003.book Page 59 Monday, November 5, 2007 10:04 AM
Dansk | 63
Bosch Power Tools 1 609 929 M89 | (5.11.07)
Støj-/vibrationsinformation
Måleværdier er beregnet iht. EN 60745.
Maskinens A-vægtede lydtrykniveau er typisk
75 dB(A). Usikkerhed K=3 dB.
Støvniveauet under arbejdet kan overskride
80 dB(A).
Brug høreværn!
Samlede vibrationsværdier (vektorsum for tre
retninger) beregnet iht. EN 60745:
Boring i metal: Vibrationseksponering
a
h
<2,5 m/s
2
, usikkerhed K=1,5 m/s
2
,
Skruer: Vibrationseksponering a
h
<2,5 m/s
2
, usik-
kerhed K=1,5 m/s
2
.
Det svingningsniveau, der er angivet i nærværen-
de instruktioner, er blevet målt iht. en standardi-
seret måleproces i EN 60745, og kan bruges til at
sammenligne el-værktøjer. Det er også egnet til
en foreløbig vurdering af svingningsbelastningen.
Det angivede svingningsniveau repræsenterer de
væsentlige anvendelser af el-værktøjet. Hvis
el-værktøjet dog anvendes til andre formål, med
afvigende indsatsværktøj eller utilstrækkelig ved-
ligeholdelse, kan svingningsniveauet afvige. Det-
te kan føre til en betydelig forøgelse af sving-
ningsbelastningen i hele arbejdstidsrummet.
Til en nøjagtig vurdering af svingningsbelastnin-
gen bør der også tages højde for de tider, i hvilke
værktøjet er slukket eller godt nok kører, men
rent faktisk ikke anvendes. Dette kan føre til en
betydelig reduktion af svingningsbelastningen i
hele arbejdstidsrummet.
Fastlæg ekstra sikkerhedsforanstaltninger til be-
skyttelse af brugeren mod svingningers virkning
som f.eks.: Vedligeholdelse af el-værktøj og ind-
satsværktøj, holde hænder varme, organisation
af arbejdsforløb.
Tekniske data
Overensstemmelseserklæring
Vi erklærer under almindeligt ansvar, at det pro-
dukt, der er beskrevet under „Tekniske data“, er
i overensstemmelse med følgende standarder el-
ler normative dokumenter: EN 60745 iht. be-
stemmelserne i direktiverne 2004/108/EF,
98/37/EF (indtil 28.12.2009), 2006/42/EF (fra
29.12.2009).
Teknisk dossier hos:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
18.09.2007, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Akku-boreskruetrækker PSR 12 PSR 14,4 PSR 18
Typenummer
3 603 J55 5.. 3 603 J55 4.. 3 603 J55 3..
Nominel spænding
V= 12 14,4 18
Omdrejningstal, ubelastet
min
-1
0700 0700 0700
Max. drejningsmoment hårdt/blødt
skruearbejde iht. ISO 5393
Nm 26/11 28/12 30/13
Max. skrue-
Ø mm 8 88
Max. bore-
Ø
–Stål
–Træ
mm
mm
10
20
10
25
10
28
Vægt svarer til EPTA-Procedure
01/2003
kg 1,4 1,5 1,7
Se typenummer på el-værktøjets typeskilt. Handelsbetegnelserne for de enkelte el-værktøjer kan variere.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
OBJ_BUCH-149-003.book Page 63 Monday, November 5, 2007 10:04 AM
1 609 929 M89 | (5.11.07) Bosch Power Tools
66 | Dansk
Kundeservice og kunderådgivning
Kundeservice besvarer dine spørgsmål vedr. re-
paration og vedligeholdelse af dit produkt samt
reservedele. Reservedelstegninger og informatio-
ner om reservedele findes også under:
www.bosch-pt.com
Bosch kundeservice-team vil gerne hjælpe dig
med at besvare spørgsmål vedr. køb, anvendelse
og indstilling af produkter og tilbehør.
Dansk
Bosch Service Center
Telegrafvej 3
2750 Ballerup
Tel. Service Center: +45 (04489) 8855
Fax: +45 (04489) 87 55
Bortskaffelse
El-værktøj, tilbehør og emballage skal genbruges
på en miljøvenlig måde.
Gælder kun i EU-lande:
Smid ikke el-værktøj ud sammen
med det almindelige husholdnings-
affald!
Iht. det europæiske direktiv
2002/96/EF om affald af elektrisk
og elektronisk udstyr skal kasseret
elektrisk udstyr indsamles separat og genbruges
iht. gældende miljøforskrifter.
Akkuer/batterier:
Ni-Cd: Nikkel-cadmium
Pas på: Disse akkuer indeholder cadmium, som
er et meget giftigt tungmetal.
Ni-MH: Nikkel-metalhydrid
Gamle akkuer/batterier må ikke smides ud sam-
men med det almindelige husholdningsaffald, ej
heller brændes eller smides i vandet. Akkuer/bat-
terier skal indsamles, genbruges eller bortskaffes
iht. gældende miljøforskrifter.
Gælder kun i EU-lande:
Iht. direktivet 91/157/EØF skal defekte eller
brugte akkuer/batterier genbruges.
Ret til ændringer forbeholdes.
OBJ_BUCH-149-003.book Page 66 Monday, November 5, 2007 10:04 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103

Bosch 0 603 955 40J Owner's manual

Category
Cordless combi drills
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI