Bunn Titan® Single DBC® 120/208V Brewer User manual

Brand: Bunn

Model: Titan® Single DBC® 120/208V Brewer

Category: Coffee makers

Type: User manual

This manual is also suitable for

TITAN DUAL

TITAN SINGLE

SERVICE & REPAIR MANUAL

BUNN-O-MATIC CORPORATION

POST OFFICE BOX 3227

SPRINGFIELD, ILLINOIS 62708-3227

PHONE: (217) 529-6601 FAX: (217) 529-6644

www.bunn.com

ENABLE

TITAN

ENABLE

BREW

TITAN

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 2

41747 031314

BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY

Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:

1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCR/MCP/MCA single cup brewers, ther-

mal servers and ThermoFresh® servers (mechanical and digital) 1 year parts and 1 year labor.

2) All other equipment - 2 years parts and 1 year labor plus added warranties as speciﬁed below:

a) Electronic circuit and/or control boards - parts and labor for 3 years.

b) Compressors on refrigeration equipment - 5 years parts and 1 year labor.

c) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis - parts and

labor for 4 years or 40,000 pounds of coffee, whichever comes ﬁrst.

These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by it will be

commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the

applicable warranty period. This warranty does not apply to any equipment, component or part that was not manufactured

by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect, alteration, improper installation or operation,

improper maintenance or repair, non periodic cleaning and descaling, equipment failures related to poor water quality,

damage or casualty. In addition, the warranty does not apply to replacement of items subject to normal use including but

not limited to user replaceable parts such as seals and gaskets. This warranty is conditioned on the Buyer 1) giving BUNN

prompt notice of any claim to be made under this warranty by telephone at (217) 529-6601 or by writing to Post Ofﬁce Box

3227, Springﬁeld, Illinois 62708-3227; 2) if requested by BUNN, shipping the defective equipment prepaid to an authorized

BUNN service location; and 3) receiving prior authorization from BUNN that the defective equipment is under warranty.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EX-

PRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN are not authorized to make modi-

ﬁcations to this warranty or to make additional warranties that are binding on BUNN. Accordingly, statements by such

individuals, whether oral or written, do not constitute warranties and should not be relied upon.

If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its exclusive op-

tion while the equipment is under warranty, shall either 1) provide at no charge replacement parts and/or labor (during the

applicable parts and labor warranty periods speciﬁed above) to repair the defective components, provided that this repair

is done by a BUNN Authorized Service Representative; or 2) shall replace the equipment or refund the purchase price for

the equipment.

THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS

EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S SOLE OPTION

AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.

In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost proﬁts, lost sales, loss of

use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities

or services, or any other special, incidental or consequential damages.

392, A Partner You Can Count On, Air Infusion, AutoPOD, AXIOM, BrewLOGIC, BrewMETER, Brew Better Not Bitter, Brew-

WISE, BrewWIZARD, BUNN Espress, BUNN Family Gourmet, BUNN Gourmet, BUNN Pour-O-Matic, BUNN, BUNN with

the stylized red line, BUNNlink, Bunn-OMatic, Bunn-O-Matic, BUNNserve, BUNNSERVE with the stylized wrench design,

Cool Froth, DBC, Dr. Brew stylized Dr. design, Dual, Easy Pour, EasyClear, EasyGard, FlavorGard, Gourmet Ice, Gourmet

Juice, High Intensity, iMIX, Infusion Series, Intellisteam, My Café, Phase Brew, PowerLogic, Quality Beverage Equipment

Worldwide, Respect Earth, Respect Earth with the stylized leaf and coffee cherry design, Safety-Fresh, savemycoffee.com,

Scale-Pro, Silver Series, Single, Smart Funnel, Smart Hopper, SmartWAVE, Soft Heat, SplashGard, The Mark of Quality in

Beverage Equipment Worldwide, ThermoFresh, Titan, trifecta, TRIFECTA (sylized logo), Velocity Brew, Air Brew, Beverage

Bar Creator, Beverage Proﬁt Calculator, Brew better, not bitter., Build-A-Drink, BUNNSource, Coffee At Its Best, Cyclonic

Heating System, Daypart, Digital Brewer Control, Element, Milk Texturing Fusion, Nothing Brews Like a BUNN, Picture

Prompted Cleaning, Pouring Proﬁts, Signature Series, Sure Tamp, Tea At Its Best, The Horizontal Red Line, Ultra are either

trademarks or registered trademarks of Bunn-O-Matic Corporation. The commercial trifecta® brewer housing conﬁgura-

tion is a trademark of Bunn-O-Matic Corporation.

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 3

INTRODUCTION

This equipment will brew coffee into an awaiting server or airpot. The brewer may have an auxillary hot water

faucet. It is only for indoor use on a sturdy and level counter or shelf. Please install in an area where there are

no water jet devices.

This brewer can be programmed to adjust different functions of the brewing process, such as brew tempera-

ture, brew volumes, bypass percentages, pulse brew, etc. Other features are Energy Savings mode, Freshness

Timer and Clean Alert.

CONTENTS

Warranty .....................................................................................................................................2

Table of Contents ........................................................................................................................3

Troubleshooting ..........................................................................................................................4

Service Tools .............................................................................................................................15

Component Access ...................................................................................................................18

Control Board ......................................................................................................................18

Membrane Switch ................................................................................................................19

Dispense and Bypass Valves................................................................................................20

Reﬁll Valves .........................................................................................................................21

Tank Heaters ........................................................................................................................22

Temperature Probe ..............................................................................................................23

Limit Thermostats ...............................................................................................................22

Contactor .............................................................................................................................23

Main Power Switch ..............................................................................................................24

Schematic (Wiring Diagram) .....................................................................................................25

41747 112608

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 4

TROUBLESHOOTING

A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems

encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic

Technical Service Department.

• Inspection, testing, and repair of electrical equipment should be performed only by qualiﬁed service person-

nel.

• All electronic components have 120-240 volt ac and low voltage dc potential on their terminals. Shorting of

terminals or the application of external voltages may result in board failure.

• Intermittent operation of electronic circuit boards is unlikely. Board failure will normally be permanent. If

an intermittent condition is encountered, the cause will likely be a switch contact or a loose connection at a

terminal or crimp.

• Solenoid removal requires interrupting the water supply to the valve. Damage may result if solenoids are

energized for more than ten minutes without a supply of water.

• The use of two wrenches is recommended whenever plumbing ﬁttings are tightened or loosened. This will

help to avoid twists and kinks in the tubing.

• Make certain that all plumbing connections are sealed and electrical connections tight and isolated.

• This brewer is heated at all times. Keep away from combustibles.

WARNING – • Exercise extreme caution when servicing electrical equipment.

• Unplug the brewer when servicing, except when electrical tests are speciﬁed.

• Follow recommended service procedures.

• Replace all protective shields or safety notices.

41747 112608

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 5

PROBABLE CAUSE REMEDYPROBLEM

TROUBLESHOOTING (cont.)

Temperature Too Low

Heating Time Too Long

Fill Time Too Long

Temp Sensor Out Of Range, Check

For Bad Connections

Temp Sensor Out Of Range, Check

Wire For Shorts

Equipment will not operate

1. Water temperature in the tank

does not meet the ready tempera-

ture.

1. Tank Heater failure.

2. Control Board/Thermistor failure

1. Water shut off to brewer

2. Inlet Solenoid failure

3. Control Board failure

4. ON/OFF switch is OFF

1. Temperature Sensor Probe

wire(s) broken or not making con-

nection

1. Temperature Sensor Probe

wire(s) shorted to housing or to

each other.

1. No power or incorrect voltage

A) Wait for the brewer to heat to the

proper temperature.

B) Disable the BREW LOCKOUT

function. Refer to Programming

Manual for procedure.

Service required

Check water supply shut-off

Service Required

Turn switch ON

Check wire and connection of both

black and white wires of temperature

probe.

Check to conﬁrm that wire(s) are

not pinched between two surfaces

or connected to each other.

Measure the voltage at the terminal

block and conﬁrm that it matches

the voltage speciﬁed on the brewer

data plate withing +/- 10%.

41747 112608

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 6

TROUBLESHOOTING (cont.)

PROBABLE CAUSE REMEDY

PROBLEM

Check plumbing and shut-off valves

Check for voltage across the termi-

nals at the terminal block.

Test the ON/OFF switch. Refer to the

test switch procedures on page 17.

Test the BREW switch. Refer to the

test switch procedures on page 17.

Test the brew valve. Refer to the

test outputs procedures on page 15.

Substitute a control board known

to be in good working order.

Check plumbing and shut-off valves

Remove the strainer and check for

obstructions. Clear or replace.

1. No water

2. No power or incorrect voltage to

the brewer

3. ON/OFF switch

4. Brew switch

5. Brew valve

6. Control Board

Brew cycle will not start

41747 112608

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 7

TROUBLESHOOTING (cont.)

PROBLEM

PROBABLE CAUSE REMEDY

Check the sensitivity setting. Refer

to the REFILL function in Program-

mimg Manual. If the left three digit

number is less than the right num-

ber, the machine “thinks” it is full and

the reﬁll valve should be off. If the left

number is larger than the right, then

the reﬁll valve will automatically be

turned on to ﬁll the tank. The right

number is the threshold setting and

can be adjusted to compensate for

extreme water conditions: very pure,

low conductance water requires a

higher setting, while high mineral

content, high conductance water

requires a lower setting. Note that

the left number changes from a high

value when water is NOT touching

the reﬁll probe to a low valve when

water IS touching the probe. For

best operation, the right number

should be set to a value midway

between these low and high num-

bers. Before changing the setting,

conﬁrm that the reﬁll probe is free

of scale buildup and the connection

to it is secure. Test the reﬁll valve.

Refer to the test outputs procedures

on page 15.

Reﬁll valve – Disconnect the brewer

from the power source and remove

wires from reﬁll valve coil. Check

for continuity across the terminals

of the solenoid coil. If continuity is

Automatic reﬁll will not operate or

display shows FILL TIME TOO LONG

1. No water

2. Reﬁll valve

3. Reﬁll probe or Sensitivity setting

41747 112608

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 8

TROUBLESHOOTING (cont.)

PROBLEM PROBABLE CAUSE REMEDY

not present, replace the reﬁll valve.

If continuity is present, the coil may

be stuck closed. Shut water off to

brewer. Press the ON/OFF switch to

turn off the brewer. Open the faucet

and drain water down in the tank

until ﬂow stops or slows to a trickle.

Attach a voltmeter to the terminals

of the reﬁll solenoid. Connect the

brewer to the power source. Press

the ON/OFF switch to turn the brewer

on. Within ﬁve seconds, voltage

should be present at the solenoid

terminals. If voltage is not present,

refer to the wiring schematic and

check the wiring harness.

Substitute a control board known

to be in good working order.

ON/OFF switch must be ON for the

reﬁll circuit to operate. Turn ON.

When this condition occurs, the

brewer will display OVERFLOW

CUP FULL. EMPTY CUP. The reason

for overﬁlling could be a defective

reﬁll valve, an incorrect sensitivity

setting, (see above) or boiling.

4. Control Board

5. ON/OFF Switch

6. Overﬂow Safety Switch

Automatic reﬁll will not operate or

display shows FILL TIME TOO LONG

(Continued)

41747 112608

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 9

TROUBLESHOOTING (cont.)

PROBLEM PROBABLE CAUSE REMEDY

Water ﬂows into tank continuously

with power removed from brewer.

1. Reﬁll valve

2. Reﬁll probe or sensitivity setting

3. Control Board

Foreign material lodged in valve,

holding it in open state.

Check the sensitivity setting. Refer

to the REFILL function in Program-

ming Manual. If the left three digit

number is less than the right num-

ber, the machine “thinks” it is full and

the reﬁll valve should be off. If the

left number is larger than the right,

then the reﬁll valve will automatically

be turned on to ﬁll the tank. The right

number is the threshold setting and

can be adjusted to compensate for

extreme water conditions: very pure,

low conductance water requires a

higher setting, while high mineral

content, high conductance water

requires a lower setting. Note that

the left number changes from a high

value when water is NOT touching

the reﬁll probe to a low valve when

water IS touching the probe. For

best operation, the right number

should be set to a value midway

between these low and high num-

bers. Before changing the setting,

conﬁrm that the reﬁll probe is free

of scale buildup and the connection

to it is secure.

Substitute a control board known

to be in good working order.

41747 112608

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 10

TROUBLESHOOTING (cont.)

PROBLEM PROBABLE CAUSE REMEDY

Water will not heat or display shows

HEATING TIME TOO LONG.

1. Limit Thermostats

2. Temperature probe

3. Tank heaters

4. Control Board

Remove power from the brewer.

Check for continuity through the

limit thermostat. CAUTION: Do not

eliminate or bypass limit thermo-

stat. Use only replacement part

23717.0003.

Remove the probe from the grom-

met and submerge in a water bath

of approximately 70°F (21°C).

Connect an ohmmeter to the pins

in the connector. At 60°F (16°C),

the reading should be 15.3k ± 2k

OHMS, at 70°F (21°C) the reading

should be 11.8k ± 2k OHMS, and

at 80°F (27°C) the reading should

be 9.3k ± 2k OHMS. If the probe is

within these parameters, reconnect

to the control board.

Remove power from the brewer.

Check for continuity through the

tank heaters. If no continuity is

present, check for a wiring problem

(consult wiring schematic), then

replace the tank heater if no wiring

problem is found.

Remove power from the brewer.

Connect a voltmeter across the

tank heater. Reapply power to the

brewer and refer to testing outputs

on page 15. If the voltage measured

when the tank heater is turned on

is very low or zero, then substitute

a control board know to be good

working order.

41747 112608

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 11

No bypass water

Spitting or unusual steaming from

sprayhead or air vent.

1. Bypass valve

1. Lime buildup

2. Temperature probe

3. Control Board

Test the bypass valve. Refer to the

test outputs procedures on page 15.

Inspect the probe and tank assembly

for excessive lime deposits. Delime

as required.

Remove the probe from the grom-

met and submerge in a water bath

of approximately 70°F (21°C).

Connect an ohmmeter to the pins

in the connector. At 60°F (16°C),

the reading should be 15.3k ± 2k

OHMS, at 70°F (21°C) the reading

should be 11.8k ± 2k OHMS, and

at 80°F (27°C) the reading should

be 9.3k ± 2k OHMS. If the probe is

within these parameters, reconnect

to the control board.

Remove power from the brewer.

Connect a voltmeter across the

tank heater. Reapply power to the

brewer and refer to testing outputs

on page 15. If the voltage measured

when the tank heater is turned on

is very low or zero, then substitute

a control board know to be good

working order.

TROUBLESHOOTING (cont.)

PROBLEM PROBABLE CAUSE REMEDY

41747 112608

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 12

TROUBLESHOOTING (cont.)

PROBLEM PROBABLE CAUSE REMEDY

Inconsistent beverage level in

server/dispenser

Check operating water pressure to

the brewer. It must be between 20

and 90 psi (138 and 620 kPa).

Test the brew valve. Refer to test

outputs on page 15. Turn the valve

on for 30 seconds and collect the

water dispensed from the spray-

head. Repeat the test several times

to conﬁrm a consistent volume of

dispensed water. If not consistent,

check the valve, tubing and spray-

head for lime buildup.

If bypass is being used on the incon-

sistent brew, test the bypass valve.

Refer to test outputs on page 15.

Turn the valve on for 30 seconds and

collect the water collected from the

funnel. Repeat the test several times

to conﬁrm a consistent volume of

dispensed water. If not consistent,

check the valve, tubing and ﬁttings

for lime buildup.

Inspect for lime buildup that could

block the tank, tank ﬁttings, tubing,

valves and sprayhead.

Adjust the brew volume, calibrate

sprayhead and bypass as required

to achieve the desired volume for

each brew cycle.

1. Improper water pressure

2. Brew valve

3. Bypass valve

4. Lime buildup

5. Brew volume adjustment

41747 112608

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 13

TROUBLESHOOTING (cont.)

PROBLEM PROBABLE CAUSE REMEDY

Dripping from sprayhead.

Water overﬂows ﬁlter.

Beverage overﬂows server.

Brewer is making unusual noises.

Repair or replace leaky valve

BUNN paper ﬁlters should be used

for proper extraction

Check sprayhead

The brew cycle should be started

only with an empty server under

the funnel.

Adjust the brew volume, calibrate

sprayhead and bypass as required

to achieve the desired volume for

each brew cycle

The mounting screws on the so-

lenoids must be tight or they will

vibrate during operation

Plumbing lines should not be resting

on the countertop.

The brewer must be connected to a

cold water line. Water pressure to

the brewer must not be higher than

90 psi (620 kPa). Install a regulator

if necessary to lower the working

pressure to approximately 50 psi

(345 kPa).

Remove and clean lime off tank

heaters.

1. Brew valve

1. Type of paper ﬁlter

2. No sprayhead

1. Beverage left in server from

previous brew

2. Brew volume adjustment

1. Solenoids

2. Plumbing lines

3. Water supply

4. Tank heaters

41747 112608

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 14

TROUBLESHOOTING (cont.)

PROBLEM PROBABLE CAUSE REMEDY

Weak beverage. BUNN paper ﬁlters should be used

for proper extraction

A sufﬁcient quantity of fresh drip

or regular grind should be used for

proper extraction.

Bunn-O-Matic sprayhead should

be used to properly wet the bed of

ground coffee in the funnel

The BUNN paper ﬁlter should be

centered in the funnel and the bed

of grounds leveled by gently shak-

ing. Use the four wire loops on the

funnel to hold ﬁlter in place while

brewing.

Empty the server, remove its cover,

and place the server beneath the

sprayhead. Place empty funnel over

the server entrance (not in the funnel

rails). Press brew. Check the water

temperature immediately below

the sprayhead with a thermometer.

The reading should not be less than

195°F (90°C).

1. Type of paper ﬁlter

2. Coffee

3. Sprayhead

4. Funnel Loading

5. Water temperature

41747 112608

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 15

SERVICE TOOLS

This function allows the testing of individual com-

ponents and the ability to check switches for proper

function.

Procedure to test components and outputs:

The following components can be individually tested:

SINGLE Brewers

Brew Valve

Bypass Valve

Funnel Lock

Reﬁll Valve

Tank Heater Relay

DUAL Brewers

Left Brew Valve

Left Bypass Valve

Left Funnel Lock

Right Brew Valve

Right Bypass Valve

Right Funnel Lock

Reﬁll Valve

Tank Heater Relay

Procedure to test components (outputs):

1. Place brew funnel(s) into rails on the brewer (both

sides on DUAL brewers).

2. Place a server(s) beneath the brew funnel(s).

3. Press and hold the right hidden button until the

display reads SET LANGUAGE. Press the right

hidden button until the display reads SERVICE

TOOLS.

4. Press and release YES. The display should now

read TEST OUTPUTS? Press and release YES to

test individual components and outputs. Pressing

NO will advance to the next programming function,

TEST SWITCHES.

5. The display should now read:

BREW VALVE on SINGLE brewers

<- <- BREW VALVE on DUAL brewers.

To test the brew valve, press ON. If the brew valve

is functional, water should run from the funnel (left

side on DUAL brewers).

6. Press OFF to end the ﬂow of water.

7. Press NEXT to advance to the next component to

be tested.

NOTE: To bypass testing any component, press NEXT

to advance to the next component without testing the

previous one.

8. The display should now read:

BYPASS VALVE on SINGLE brewers

<- <- BYPASS VALVE on DUAL brewers

To test the left bypass valve, press ON. If the

bypass valve is functional, water should run from

the funnel (left funnel on DUAL brewers).

9. Press OFF to end the ﬂow of water.

10. Press NEXT to advance to the next component to

be tested.

11. To test FUNNEL LOCK on SINGLE brewers or LEFT

FUNNEL LOCK on DUAL brewers, press ON. If the

funnel lock is functional, the lock will come down

to hold the funnel in place.

12. Press OFF to retract the funnel lock.

13. For DUAL brewers, follow steps 5-12 to test the

right side components.

14. To test the REFILL VALVE, press ON. If the reﬁll

valve is functional, the sound of the valve operating

will be heard.

15. Press OFF to end testing of the reﬁll valve.

16. Press NEXT to advance to the next component to

be tested, TANK HEATR RELAY.

17. To test the tank heater relay, connect a voltmeter

across each of the tank heaters to check for volt-

age.

18. Press ON. The correct voltage should be present

at the heater terminals.

19. Press OFF to end testing of the tank heater relay.

NOTE: The tank heater will automatically turn off if

left on too long.

20. Press NEXT to return to the TEST OUTPUTS

screen. To advance to the next function screen,

TEST SWITCHES, press NO. To exit programming,

press and release the ON/OFF switch (either on

DUAL brewers) to return to the MAIN SCREEN.

Procedure to test switches:

This function allows the operator to test the opera-

TROUBLESHOOTING (cont.)

41747 112608

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 16

SERVICE TOOLS (cont.)

TROUBLESHOOTING (cont.)

TEST OUTPUTS?

NO YES

SERVICE TOOLS?

NO YES

LEFT BREW VALVE

ON NEXT OFF

LEFT BYPASS

ON NEXT OFF

LEFT FUNNEL LOCK

ON NEXT OFF

RIGHT BREW VALVE

ON NEXT OFF

RIGHT BYPASS

ON NEXT OFF

RIGHT FUNEL LOCK

ON NEXT OFF

REFILL VALVE

ON NEXT OFF

TANK HEATR RELAY

ON NEXT OFF

BREW VALVE

ON NEXT OFF

BYPASS

ON NEXT OFF

FUNNEL LOCK

ON NEXT OFF

SINGLE

BREWERS

DUAL

BREWERS

EXIT TO

NEXT FUNCTION

SCREEN

TEST SWITCHES?

NO YES

NOTHING PRESSED

AFTER ALL SWITCHES ARE

TESTED PRESS RIGHT

HIDDEN TO RETURN TO

TEST SWITCHES

41747 101818

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 17

SERVICE TOOLS (cont.)

TROUBLESHOOTING (cont.)

tion of the individual switches on the front panel.

The following switches can be individually tested:

SINGLE Brewers:

Full Batch

Half Batch

Power

Brew Switch

Left Hidden

DONE

(-)

(+)

DUAL Brewers:

<- <- Full Batch Full Batch -> ->

<- <- Half Batch Half Batch -> ->

<- <- Power Power -> ->

<- <- Brew Switch Brew Switch -> ->

Left Hidden DONE

(-) (+)

1. Place brew funnel(s) into rails on the brewer (both

sides on DUAL brewers).

2. Place server(s) beneath the brew funnel(s).

3. Press and hold the upper right hidden switch until

display reads SET LANGUAGE. Release the switch.

Continue to press and release switch until SERVICE

TOOLS appears.

4. Press and release YES. The display should read

TEST OUTPUTS?. Press and release NO to advance

to TEST SWITCHES.

5. Pressing NO in this screen will advance to the

next function. Press YES in the TEST SWITCHES

screen to test the switches. The display will read

NOTHING PRESSED.

6. From this screen, press any of the switches on the

front of the brewer except the upper right hidden

switch. While the switch is pressed, the display

shows the name of that switch. If the name does

not appear, or if it remains after the switch has been

released, the switch is defective. Each switch can

be tested in this manner.

7. After all switches have been tested, press and re-

lease the right hidden switch (®). This will return

to TEST SWITCHES?. To exit programming, press

and release the ON/OFF switch (either on DUAL

brewers) located on the front switch panel. This

will exit TEST SWITCHES and return to the MAIN

SCREEN.

NOTE: If the operator wishes to test more than one

function in the SERVICE TOOLS section (outputs or

switches), it is not necessary to exit the program.

Use the ﬂow chart for SERVICE TOOLS to navigate

to a particular function.

41747 112608

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 18

COMPONENT ACCESS

This section provides procedures for testing and

replacing various major components used in this

brewer should service become necessary. Refer to

Troubleshooting for assistance in determining the

cause of any problem.

WARNING

- Inspection, testing, and repair of electri-

cal equipment should be performed only by qualiﬁed

service personnel. The brewer should be disconnected

from power source when servicing, except when

electrical tests are required and the test procedure

speciﬁcally states to plug in the brewer.

WARNING - Disconnect the brewer from the power

source before the removal of any panel or the replace-

ment of any component.

All components are accessible by the removal of

the top cover, front access panel.

Refer to wiring diagrams at the back of this manual

when reconnecting wires.

CONTROL BOARD

Location:

The Control Board (Fig 1) is located under the top

cover behind the control panel.

Check for Power to board:

1. Insert one meter lead in J17-pin 9 and the other

lead in J17-pin 11.

2. With the power connected to brewer, the voltage

reading to the board should be the line voltage

rated for that model.

If no voltage is present, check wiring to the board.

If voltage is present, and brewer does not power

on, replace board.

Removal and Replacement:

1. Disconnect brewer from power source.

2. Disconnect the main harness from the 14 pin con-

nector J17 on the control board.

3. Disconnect the ribbon cable from connector J2 on

the control board.

4. Disconnect the temperature probe harness from

connector J13 on the control board.

5. Disconnect level probe and overﬂow cup from the

8 pin connector J3 on the control board.

6. Disconnect transformer from connector J15 on

the control board.

7. Remove the two mounting nuts securing the top

of the control board to the hood.

8. Tilt the control board inward to clear the display

section and lift out of the control board mount.

9. Place the bottom edge of the new control board

in the control board mount, tilt the board forward,

and secure with the two keps nuts.

10. Re-connect wires to the circuit board.

FIG 1 CONTROL BOARD MOUNTING

Control Board Mount

Control Board Mounting Nut

Ribbon Cable

41747 112608

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 19

Location:

The Membrane Switch (Fig 2) is located on the front

of the hood with a ribbon cable extending through the

hood and connected to the control board.

Test Procedures:

There are two methods for testing the membrane

switch. The easiest method is to use the built in test

mode. Refer to the Trouble Shooting Section for Service

Tools/Test Switches. If for some reason you can't get

into the program modes, or brewer won't power up,

you can test it with an ohmmeter or continuity tester.

Refer to the schematic to trace the appropriate pins.

NOTE: Pin 1 is the static shield & will not provide a

reading to the other pins. There are three commons

in this circuit, pins #9, 10 & 21.

Disconnect brewer from power source before discon-

necting ribbon cable from control board.

Removal and Replacement:

1. Disconnect the ribbon cable from 22-pin connector

on the control board.

2. Gently peel the membrane switch from the hood.

3. Remove any adhesive that remains on the hood.

4. Remove the adhesive backing from the new mem-

brane switch. Insert the ribbon cable through the

slot in the hood and apply the membrane switch

to the front of the hood.

5. Reconnect the ribbon cable to the 22-pin connec-

tor on the control board making sure every pin on

the control board is inserted into the ribbon cable

connector.

FIG 2 MEMBRANE SWITCH

COMPONENT ACCESS (cont)

MEMBRANE SWITCH

ENABLE

TITAN

Membrane Switch

41747 101818

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page 20

Location:

The bypass valve(s) (Fig 3) are located inside the

hood under the top cover.

Test Procedures:

1. Refer to the Trouble Shooting Section for Service

Tools/Test Outputs/Bypass Valve.

2. Be sure brew funnel & server are in place before

activating valve.

3. Check the valve for coil action. Turn on the valve

with the test mode. Listen carefully in the vicinity

of the bypass valve for a click as the coil pulls the

plunger in.

If no sound is heard as described, proceed to #4.

If the sound is heard as described, there may be

a blockage in the valve , hose, or tank. Disconnect the

brewer from the power source. Remove the valve and

inspect for blockage, and de-lime all related areas.

4. Connect the voltmeter leads to the coil terminals.

Turn on the valve with the test mode. NOTE: Due

to the internally rectiﬁed coil, the indication will

be 120VAC all the time. Set the meter to DC volts.

The indication should be 170VDC when activated.

If the polarity of meter leads are reversed, reading

will indicate -170VDC. (Double these readings for

240 volt coils)

If voltage is present as described, but no coil action

is observed, valve is defective. Replace valve and test

again to verify repair.

If voltage is not present as described, refer to Wir-

ing Diagrams and check the brewer wiring harness.

Also check the control board and switch for proper

operation.

Removal and Replacement:

1. Disconnect the brewer from the power source.

2. Disconnect wires from the valve.

3. Drain enough water from the tank so the water

level is below the outlet.

4. Remove tube(s) from the valve.

5. Remove the two #8-32 nuts mounting valve to the

bracket.

6. Install new valve using nut(s) removed in step 5.

7. Reconnect tube(s) to the valve and secure in place

with clamp(s).

FIG 3 BYPASS/DISPENSE VALVES

COMPONENT ACCESS (cont)

BYPASS VALVES

DISPENSE VALVES

Location:

The dispense valve(s) (Fig 3) are located inside

the hood under the top cover.

Test Procedures:

1. Refer to the Trouble Shooting Section for Service

Tools/Test Outputs/Dispense Valve.

2. Be sure brew funnel & server are in place before

activating valve.

3. Check the valve for coil action. Turn on the valve

with the test mode. Listen carefully in the vicinity

of the dispense valve for a click as the coil pulls

the plunger in.

If no sound is heard as described, proceed to #4.

If the sound is heard as described, there may be a

blockage in the valve , hose, tank, or sprayhead. Dis-

connect the brewer from the power source. Remove

the valve and inspect for blockage, and de-lime all

related areas.

4. Connect the voltmeter leads to the coil terminals.

Dispense Valve

Bypass Valve

Contactor

41747 112608

RELEASED FOR PRODUCTION

DIR Num: 41747.0000 12, December 2018

Page is loading ...

Bunn Titan® Single DBC® 120/208V Brewer User manual

Brand: Bunn

Model: Titan® Single DBC® 120/208V Brewer

Category: Coffee makers

Type: User manual

This manual is also suitable for

Download PDF

report

Bunn Titan® Single DBC® 120/208V Brewer User manual

This manual is also suitable for

Bunn Titan® Single DBC® 120/208V Brewer User manual

Related papers

Other documents