INSTALLATION INSTRUCTIONS
E-MT5, E-MT6, AND E-MT7 SERIES
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following:
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
1. Make certain power is OFF before starting installation or
attempting any maintenance.
2. Fixture comes standard with a HOT, COMMON and GROUND
wire or ground lug.
3. 90°C supply wire required for E-MT5A301G. All others require
60°C supply wire.
4. Mounting locations above 4 feet (1.2 meters), caulking of
canopy to mounting surface and fixture must not be used
without lamp shields
SAVE THESE INSTRUCTIONS
Turn off power supply to avoid the risk of electrical shock. This
product must be wired in accordance with the National Electrical
Code and applicable local codes and ordinances. Proper grounding
is required to ensure personal safety. A qualified electrician should
do all work.
CAUTIONS
1. Remove (3) screws connecting the pendant mounting/ballast
cover to the fixture housing.
2. Thread the pendant mounting cover onto the conduit.
3. Complete the wiring to the power source (refer to wiring
instructions)
4. Seal around the conduit using approved NEC procedures.
5. If necessary, align gasket with holes in fixture housing.
6. Reinsert and tighten (3) screws connecting the pendant mounting
cover to the fixture housing.
MOUNTING TO CONDUIT PENDANT MOUNTING
(E-MTA AND E-MT6 SERIES)
Document Date
Drawing/Page DCR#
CI308X10R1
JAD 10-162
08/02/10
www. e-conolight.com 888.243.9445 FAX: 262.504.5409
1. Remove (3) screws connecting the ballast cover to the fixture
housing.
2. Remove (2) screws connecting the ballast cover to the
Mounting Arm.
3. Remove (4) screws connecting the mounting arm to the J-box.
4. Attach the J-Box to the mounting surface.
5. Attach conduit to J-box and pull leads to the box.
6. Seal around the conduit using approved NEC procedures.
7. Complete the wiring to the power source (refer to
wiring instructions).
8. Reassemble fixture by reversing steps 1, 2 & 3.
NOTE: Make sure to properly align gaskets between the
mounting and ballast cover and between the ballast cover
and fixture when reassembling.
WALL MOUNTING (E-MT7 SERIES)
E-MT6A301G
E-MT7A301G
E-MT5A301G
E-MT7F421G
E-MT7M07DG
E-MT7H151G
E-MT6F421G
E-MT6M07DG
E-MT6H151G
E-MT5F421G
E-MT5M07DG
E-MT5H151G
1. Remove (3) screws connecting the ballast cover to the
fixture housing.
2. Remove (2) screws connecting the ballast cover to the J-box.
3. Attach the J-box to the mounting surface.
4. Attach conduit to J-box and pull leads to the box.
5. Seal around the conduit using approved NEC procedures.
6. Complete the wiring to the power source (refer to
wiring instructions.)
7. Reassemble fixture by reversing steps 1 & 2.
NOTE: Make sure to properly align gasket between the ballast
cover and fixture when reassembling.
CEILING MOUNTING (E-MT5 SERIES)
1. Loosen guard set screws.
2. Remove globe and guard assembly.
3. Install recommended lamp only.
4. Re-install globe and guard assembly.
5. Tighten guard set screws.
LAMP INSTALLATION
INSTALLATION INSTRUCTIONS
E-MT5, E-MT6, AND E-MT7 SERIES
Document Date
Drawing/Page DCR#
CI308X10R1
JAD 10-162
08/02/10
www. e-conolight.com 888.243.9445 FAX: 262.504.5409
1. Turn power supply off.
2. Connect the black fixture lead (120V) to the HOT (usually black)
supply lead.
3. Connect the white fixture lead to the white supply lead
(COMMON).
4. Connect ground as appropriate. (NOTE: This fixture will have
either a “Green Ground lug” or a ground wire for grounding
the fixture.)
5. Cap and insulate all unused leads.
6. Be sure any unused wiring entrances are closed with closure
plugs provided.
INCANDESCENT FIXTURES
WIRING
1. Turn power supply off.
2. Connect the appropriate ballast voltage lead (120V or 277V) to
the HOT (usually black) supply lead.
3. Connect the ballast “Common” lead (usually white) to the
incoming “Common” lead (usually white).
4. Connect ground as appropriate. (NOTE: This fixture will have
either a “Green Ground lug” or a ground wire for grounding
the fixture.)
5. Cap and insulate all unused leads.
6. Be sure any unused wiring entrances are closed with closure
plugs provided.
HID FIXTURES
1. Turn power supply off.
2. Connect the black fixture lead to the HOT (usually black) supply
lead.
3. Connect the white fixture lead to the white supply lead
(COMMON).
4. Connect ground as appropriate. (NOTE: This fixture will have
either a “Green Ground lug” or a ground wire for grounding
the fixture.)
5. Cap and insulate all unused leads.
6. Be sure any unused wiring entrances are closed with closure
plugs provided.
FLUORESCENT FIXTURES
/