e-conolight E-E-MT6F421G Installation guide

Brand: e-conolight

Model: E-E-MT6F421G

Type: Installation guide

INSTALLATION INSTRUCTIONS

E-MT5, E-MT6, AND E-MT7 SERIES

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should

always be followed including the following:

READ AND FOLLOW ALL

SAFETY INSTRUCTIONS

1. Make certain power is OFF before starting installation or

attempting any maintenance.

2. Fixture comes standard with a HOT, COMMON and GROUND

wire or ground lug.

3. 90°C supply wire required for E-MT5A301G. All others require

60°C supply wire.

4. Mounting locations above 4 feet (1.2 meters), caulking of

canopy to mounting surface and fixture must not be used

without lamp shields

SAVE THESE INSTRUCTIONS

Turn off power supply to avoid the risk of electrical shock. This

product must be wired in accordance with the National Electrical

Code and applicable local codes and ordinances. Proper grounding

is required to ensure personal safety. A qualified electrician should

do all work.

CAUTIONS

1. Remove (3) screws connecting the pendant mounting/ballast

cover to the fixture housing.

2. Thread the pendant mounting cover onto the conduit.

3. Complete the wiring to the power source (refer to wiring

instructions)

4. Seal around the conduit using approved NEC procedures.

5. If necessary, align gasket with holes in fixture housing.

6. Reinsert and tighten (3) screws connecting the pendant mounting

cover to the fixture housing.

MOUNTING TO CONDUIT PENDANT MOUNTING

(E-MTA AND E-MT6 SERIES)

Document Date

Drawing/Page DCR#

CI308X10R1

JAD 10-162

08/02/10

www. e-conolight.com 888.243.9445 FAX: 262.504.5409

1. Remove (3) screws connecting the ballast cover to the fixture

housing.

2. Remove (2) screws connecting the ballast cover to the

Mounting Arm.

3. Remove (4) screws connecting the mounting arm to the J-box.

4. Attach the J-Box to the mounting surface.

5. Attach conduit to J-box and pull leads to the box.

6. Seal around the conduit using approved NEC procedures.

7. Complete the wiring to the power source (refer to

wiring instructions).

8. Reassemble fixture by reversing steps 1, 2 & 3.

NOTE: Make sure to properly align gaskets between the

mounting and ballast cover and between the ballast cover

and fixture when reassembling.

WALL MOUNTING (E-MT7 SERIES)

E-MT6A301G

E-MT7A301G

E-MT5A301G

E-MT7F421G

E-MT7M07DG

E-MT7H151G

E-MT6F421G

E-MT6M07DG

E-MT6H151G

E-MT5F421G

E-MT5M07DG

E-MT5H151G

1. Remove (3) screws connecting the ballast cover to the

fixture housing.

2. Remove (2) screws connecting the ballast cover to the J-box.

3. Attach the J-box to the mounting surface.

4. Attach conduit to J-box and pull leads to the box.

5. Seal around the conduit using approved NEC procedures.

6. Complete the wiring to the power source (refer to

wiring instructions.)

7. Reassemble fixture by reversing steps 1 & 2.

NOTE: Make sure to properly align gasket between the ballast

cover and fixture when reassembling.

CEILING MOUNTING (E-MT5 SERIES)

1. Loosen guard set screws.

2. Remove globe and guard assembly.

3. Install recommended lamp only.

4. Re-install globe and guard assembly.

5. Tighten guard set screws.

LAMP INSTALLATION

INSTALLATION INSTRUCTIONS

E-MT5, E-MT6, AND E-MT7 SERIES

Document Date

Drawing/Page DCR#

CI308X10R1

JAD 10-162

08/02/10

www. e-conolight.com 888.243.9445 FAX: 262.504.5409

1. Turn power supply off.

2. Connect the black fixture lead (120V) to the HOT (usually black)

supply lead.

3. Connect the white fixture lead to the white supply lead

(COMMON).

4. Connect ground as appropriate. (NOTE: This fixture will have

either a “Green Ground lug” or a ground wire for grounding

the fixture.)

5. Cap and insulate all unused leads.

6. Be sure any unused wiring entrances are closed with closure

plugs provided.

INCANDESCENT FIXTURES

WIRING

1. Turn power supply off.

2. Connect the appropriate ballast voltage lead (120V or 277V) to

the HOT (usually black) supply lead.

3. Connect the ballast “Common” lead (usually white) to the

incoming “Common” lead (usually white).

4. Connect ground as appropriate. (NOTE: This fixture will have

either a “Green Ground lug” or a ground wire for grounding

the fixture.)

5. Cap and insulate all unused leads.

6. Be sure any unused wiring entrances are closed with closure

plugs provided.

HID FIXTURES

1. Turn power supply off.

2. Connect the black fixture lead to the HOT (usually black) supply

lead.

3. Connect the white fixture lead to the white supply lead

(COMMON).

4. Connect ground as appropriate. (NOTE: This fixture will have

either a “Green Ground lug” or a ground wire for grounding

the fixture.)

5. Cap and insulate all unused leads.

6. Be sure any unused wiring entrances are closed with closure

plugs provided.

FLUORESCENT FIXTURES

e-conolight E-E-MT6F421G Installation guide

e-conolight E-E-MT6F421G Installation guide

e-conolight E-E-MT6F421G Installation guide

Related papers

Other documents