HDI Advanced 3D Scanner Quick start guide

Brand
HDI
Model
Advanced 3D Scanner
Category
Network media converters
Type
Quick start guide
Quick Start Guide
15190-2.3_MANUAL_Quickstart-HDI-Advance.pdf
Getting Started with the HDI Advance 3D Scanner
This quick start guide provides you with the resources to get you started on 3D scanning.
The HDI Advance 3D Scanner comes with:
• 3Dscanningsoftware,FlexScan3D
• Physicalcapturingunitforcapturing3Ddata(someassemblyisrequired)
Downloading FlexScan3D Software
TheHDIAdvance3DScannerispoweredbyFlexScan3D.Youcandownloadthesoftwarefromthe
DownloadCenter(downloads.lmi3d.com).Tocreateadownloadaccount,pleasesendyourcontact
name,emailaddress,companyname,andscannermodeltoorders@lmi3D.com.
InstructionsforinstallingandactivatingFlexScan3DusinginstallationIDordonglecanbefoundin
theUserManualunder“GettingStarted”:http://manual.lmi3d.com.
Assembling the Capturing Unit
InstructionsforassemblycanbefoundinthisQuickStartGuide.
Customer Support
Ifyouhaveanyinstallationissues,pleasecontact:
Worldwide Email:
support@lmi3D.com
Web:
www.lmi3D.com
North America Phone:
+1 604 636 1011
Europe Phone:
+31 45 850 7000
CongratulationsonpurchasingtheHDIAdvance3DScanner.Herearethestepstosetupthecapturing
unitfor3Ddataacquisition.InthistutorialtheHDIAdvanceR3x3DScannerwasused.Thereareslight
variationstotheinstructionsdependingonwhichmodelyouhavepurchased.Pleaseseethefollowing
instructionstoassembleyour3Dscanner,mostofwhichwillbepre-assembled.
WhenyoureceiveyourHDIAdvance3DScanner,checkthatallcomponentsareincluded:
Number Item
1 CarbonFiberMountwithProjectorandRemote
2 2xUSB3.0Cameras
3 2xLenses(12mm)
4 Tripod Leg
5 Tripod Head
6 15mmCalibrationBoard
7 1sheetofPhotogrammetryDots
8 FlexScan3DDongle
9 Powercable,VGAcable,USB3.0cable(3m)
10 HexKey,2mm,16x83mm
11 HexKey,5/32"ShortArmKey
12 4xScrews
2
8
10
7
3
9
5
6
4
1
11
12
Tripod Setup
Simplyopenupthetripodlegsandplacethemrmlyontheground.
Attachthetripodheadtothelegsbyrmlytwistingthetripodheaduntilitishandtight.
Connect the Scanner to the Tripod
Carefullyliftupyourpre-assembledscannerandlocatemountadapter.Gentlyplacethescanner
ontothetripodhead.Thiswillsnapintoplacewhenthescannerrestsontopofthetripodhead.
Attach the Cameras to the Scanner
Attachthetwocamerasontothescanneronbothsidesusingthescrews.Tightenscrewsuntilthey
arermbutdonotovertighten.
Attach the Lenses to the Cameras
Carefullyremovethelensesfromthepackagingandtakeothecameralenscapfromeach
camera.Thelenseswillneedtobescrewedontothecamerasuntiltheyarehandtight.
Connect the VGA and Power Cables to the Projector
LocatethebackofyourprojectorandattachtheVGAandpowercables.
Connect the USB 3.0 Cables to the Cameras
AttachtheUSB3.0cablestothebackofthecameras,andlockthecableswiththelockingscrews.
ConnectUSB3.0cablesandVGAcabletoyourcomputer.Plugthepowercableintoanelectrical
outlet.ThephysicalassemblyoftheHDIAdvance3DScannerisnowcomplete.
Copyright©2014LMITechnologiesInc.Allrightsreserved.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

HDI Advanced 3D Scanner Quick start guide

Brand
HDI
Model
Advanced 3D Scanner
Category
Network media converters
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents