Pitco Pasta/Rethermalizer Digital Controller User manual
- Type
- User manual
If display shows "LOC" Press then , This will unlock the
programming function and allow changes to be made to settings
Press , Display will show "Pr09" (Program) the indicator lights above both
Press or , Display will show "XX" (XX = current timer setting) Indicator
above or function key will illuminate to indicate which (left or right) timer is
being programmed
Press the or function keys to change set time
Press to save new timer setting
Press to exit programming
Press , Display will show "LOC or Pr09" (Program)
Press to turn controller ON
Press and hold for 3 seconds to turn controller OFF
Press to start LEFT timer/basket lift
Press to start RIGHT timer/basket lift
Press , Display will show "BOIL or SIM" Note: Simmer mode runs at 190 F
Press until display shows desired selection
Press for programming mode
PASTA COOKER AND RETHERMALIZER DIGITAL
CONTROLLER PROGRAMMING INSTRUCTIONS
CONTROLLER FUNCTIONS
TIMER PROGRAMMING INSTRUCTIONS
ENTERING LEVEL 1 PROGRAMMING
*
*
*
*
*
*
*
*
PP
PP
ON
OFF
L BASKET/ TIMER
R BASKET/ TIMER
BOIL SIMMER
PROGRAMMING
and functions key will illuminate.
*
*
*
*
*
*
PP
PP
PP
PASSWORD
TIMER SET
SECTION 4.0
PROGRAM
KEY
TIMING
START/STOP
KEYS
L20-278 rev 0
Press , Display will show "LOC or Pr09" (Program)
If display shows "LOC" Press then , This will unlock the
programming function and allow changes to be made to settings
Press , Display will show "Pr09" (Program) the indicator lights above both
Press and hold for 2 seconds, display will show "XXXF" you are now in
SIMMER MODE TEMPERATURE PROGRAMMING (XXXF = current set
temperature for the simmer mode)
NOTE: Press and hold to save setting or exit at any time in the programming
sequence.
Press the or function keys to change set temperature
Press , Display will show "T 1 or T 0" (T 1 = actual temperature always
appearing display window, T 0 = SIM or BOIL will always appear in display window
when controller is operation mode)
Press , Display will show "LOC or ULOC" (LOC = turns pass word function
ON so that a pass word is required to enter programming mode, ULOC = turns pass
word requirement OFF)
Press , Display will show "LIF1 or LIF2" (LIF1 = tells the controller that
cooker has only a single basket lift, LIF2 = tells the controller cooker has two basket
lifts)
and functions key will illuminate.
*
*
*
*
*
*
*
*
*
UPPER LEVEL PROGRAMMING INSTRUCTIONS
LIF1
ULOC
LOC
T 1, T0
PP
PP
PP
PP
PP
PP
PP
PROGRAMMING
PASSWORD
SIMMER MODE
TEMP
SAVE / EXIT
ACTUAL
TEMP
DISPLAY
PASSWORD
SET
BASKET
LIFT
TO SAVE SETTINGS OR EXIT PROGRAMMING
NOTE: Press and hold to save setting or exit at any time in the
programming sequence.
PP
*
Indicates controller is under temperature set point and burners are on
Indicator light, when illuminated, indicates burners are on
Indicates unit is in boil mode
Indicates unit is in simmer mode
Boil
S I M
_ . _ _ F
_ . _ _ F
-
1
-
2
Pitco Pasta/Rethermalizer Digital Controller User manual
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Vulcan-Hart ML-136497 User manual
-
Hobart HFC85 ML-135558 User manual
-
Hobart ML-135537 User manual
-
Hobart HGFC45 ML-126421 User manual
-
-
Pitco Frialator Compact Pasta Control User manual
-
-
Vulcan GR45 User manual
-
Pitco Frialator SSHLV14 User manual
-
Alto Shaam ASF-60E Operating instructions
