Sensitech TagAlert Operating instructions

Brand: Sensitech

Model: TagAlert

Type: Operating instructions

Millions Depend on the Integrity of Your Product.

Sensitech’s Mission is to Ensure that Integrity.

TagAlert® Indicator

Instructions For Use

The Tools That Turn Information Into Power

For more information, contact our client services

group at 800-843-8367.

Sensitech Inc. • 800 Cummings Center, Suite 258X • Beverly, MA 01915

1-800-843-8367 • +1-978-927-7033 • Fax 978-921-2112 • www.sensitech.com

TempTale Manager®

Desktop Software

TempTale®4 Monitor

RF Monitoring

TagAlert® Indicator

Data Management Services

TempTale®4 USB Monitor

AlarmAlert™ Feature

• Ifalarmed,theTagAlertindicatorprovidesamechanismtodetermineatwhichpointduring

 thetriptherstalarmwastriggered.ThisAlarmAlert™featurecanaccommodatetripsup

 to10daysinduration.

• ReadtheTagAlertandrecordwhichalarmshavetriggered(Figure 2).

• Followthenextthreestepstodeterminewhichalarmwastriggeredrstandtheapproximate

 timeatwhichthealarmtriggered:

1.PresstheStartbuttontodeterminewhichalarmtriggeredrst.Thenumberrepresent

  ingtherstalarmthattriggeredwillashfor4seconds.TheLCDdisplaywillthenclear

  for2seconds.

2. Thesumofthenumbersthatappearnextwillequalthedayintothetripthattherstalarm

was triggered (Figure 4).Thiswillbedisplayedfor2seconds.

3. Thesumofthenumbersthatappearnextwillindicatethe3-hourtimeintervalwithinthe

  daytherstalarmwastriggered(Figure 5).

• PresstheStartbuttonagaintorepeatsequenceofinformation.

Numbers Displayed on LCD Sum = Day of Trip

1 1st

2 2nd

3 3rd

44th

4 and 1 5th

4 and 2 6th

4 and 3 7th

4 and 3 and 1 8th

4 and 3 and 2 9th

4 and 3 and 2 and 1 10th

Numbers Displayed on LCD Sum Representing Time Interval Time Interval in 24 Hour Period

1 1st 0-3rdhour

2 2nd 3rd-6thhour

3 3rd 6th-9thhour

44th 9th-12thhour

4 and 1 5th 12th-15thhour

4 and 2 6th 15th-18thhour

4 and 3 7th 18th-21thhour

4 and 3 and 1 8th 21-24thhour

4 and 3 and 2 and 1 10th After10thday

Starting a TagAlert® Indicator

• PushtheSTARTbuttononthefrontofthedeviceandholdfor

 approximately1second.

• TheLCDdisplaywillrespondbydisplaying“OK”(Figure 1).

• Oncethe“OK”isdisplayed,theTagAlert®indicatorhasbeen

 activatedandentersthestart-updelayasprogrammedintotheunit.

• Onceactivated,removethebackstickerlabelandafxtoan

 instructioncardorattachdirectlytoaclean,drysurfaceofthe

 productorpackage.

Reading a TagAlert Indicator

• Oncethepackagehasarrivedatitsdestination,removethe

 TagAlertindicatorfromthepackage.

• IftheLCDdisplays“OK”,noalarmshavebeentriggered

 duringthetrip(Figure 1).

• IftheLCDdisplaysblacksquaresoverthe“OK”andthenumbers

 1,2,3and/or4,thenanalarmhasbeentriggered(Figure 2).

 Forexample,ifthenumbers1and4aredisplayed,thenthe1stand

 4thalarmconditionswereexceeded.

• Thereceivinglocationshouldfollowtheappropriateprotocolto

 determineproductdispositionifanalarmhastriggered.

Fail Safe Protection

• TheTagAlertindicatorperformsasystemcheckduringoperation

 andincorporatesaFail-Safeprotectionmodetoalerttheuser

 shouldtheunitfailtofunctionproperly.

• IftheTagAlertindicatordetectsafaultytemperaturesensororthe

 temperatureexceedstheoperationallimits(70ºC(158ºF)to-20ºC

 (-4ºF))intransit,theunitwillenterintothismodeandwill

 discontinuetemperaturemeasurement.

• TheLCDwilldisplayblacksquaresoverthe“OK”.Nonumbers

 willbedisplayedontheLCD(Figure 3).

NOTE: If any numbers appear on the LCD, that alarm has

triggered. The “OK” may still be visible through the black

squares even if an alarm has triggered.

NOTE: Days are calculated in 24 hour increments. This begins when the start button is

rst pressed and the “OK” is displayed on the LCD.

Figure 1

Figure 2

Figure 4

Figure 5

Figure 3

Sensitech TagAlert Operating instructions

Brand: Sensitech

Model: TagAlert

Type: Operating instructions

Download PDF

report

Sensitech TagAlert Operating instructions

Sensitech TagAlert Operating instructions

Related papers

Other documents