2. Sensitech
  3. TagAlert

Sensitech TagAlert Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Sensitech TagAlert Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Millions Depend on the Integrity of Your Product.
Sensitech’s Mission is to Ensure that Integrity.
TagAlert® Indicator
Instructions For Use
The Tools That Turn Information Into Power
For more information, contact our client services
group at 800-843-8367.
Sensitech Inc. • 800 Cummings Center, Suite 258X • Beverly, MA 01915
1-800-843-8367 • +1-978-927-7033 • Fax 978-921-2112 • www.sensitech.com
TempTale Manager®
Desktop Software
TempTale®4 Monitor
© 2014 Sensitech, Inc. All Rights Reserved. T83000034 Rev. H 07/09/14
RF Monitoring
TagAlert® Indicator
Data Management Services
TempTale®4 USB Monitor
AlarmAlert™ Feature
• Ifalarmed,theTagAlertindicatorprovidesamechanismtodetermineatwhichpointduring
 thetriptherstalarmwastriggered.ThisAlarmAlert™featurecanaccommodatetripsup
 to10daysinduration.
• ReadtheTagAlertandrecordwhichalarmshavetriggered(Figure 2).
• Followthenextthreestepstodeterminewhichalarmwastriggeredrstandtheapproximate
 timeatwhichthealarmtriggered:
1.PresstheStartbuttontodeterminewhichalarmtriggeredrst.Thenumberrepresent
  ingtherstalarmthattriggeredwillashfor4seconds.TheLCDdisplaywillthenclear
  for2seconds.
2. Thesumofthenumbersthatappearnextwillequalthedayintothetripthattherstalarm
was triggered (Figure 4).Thiswillbedisplayedfor2seconds.
3. Thesumofthenumbersthatappearnextwillindicatethe3-hourtimeintervalwithinthe
  daytherstalarmwastriggered(Figure 5).
• PresstheStartbuttonagaintorepeatsequenceofinformation.
Numbers Displayed on LCD Sum = Day of Trip
1 1st
2 2nd
3 3rd
44th
4 and 1 5th
4 and 2 6th
4 and 3 7th
4 and 3 and 1 8th
4 and 3 and 2 9th
4 and 3 and 2 and 1 10th
Numbers Displayed on LCD Sum Representing Time Interval Time Interval in 24 Hour Period
1 1st 0-3rdhour
2 2nd 3rd-6thhour
3 3rd 6th-9thhour
44th 9th-12thhour
4 and 1 5th 12th-15thhour
4 and 2 6th 15th-18thhour
4 and 3 7th 18th-21thhour
4 and 3 and 1 8th 21-24thhour
4 and 3 and 2 and 1 10th After10thday
Starting a TagAlert® Indicator
• PushtheSTARTbuttononthefrontofthedeviceandholdfor
 approximately1second.
• TheLCDdisplaywillrespondbydisplaying“OK”(Figure 1).
• Oncethe“OK”isdisplayed,theTagAlert®indicatorhasbeen
 activatedandentersthestart-updelayasprogrammedintotheunit.
• Onceactivated,removethebackstickerlabelandafxtoan
 instructioncardorattachdirectlytoaclean,drysurfaceofthe
 productorpackage.
Reading a TagAlert Indicator
• Oncethepackagehasarrivedatitsdestination,removethe
 TagAlertindicatorfromthepackage.
• IftheLCDdisplays“OK”,noalarmshavebeentriggered
 duringthetrip(Figure 1).
• IftheLCDdisplaysblacksquaresoverthe“OK”andthenumbers
 1,2,3and/or4,thenanalarmhasbeentriggered(Figure 2).
 Forexample,ifthenumbers1and4aredisplayed,thenthe1stand
 4thalarmconditionswereexceeded.
• Thereceivinglocationshouldfollowtheappropriateprotocolto
 determineproductdispositionifanalarmhastriggered.
Fail Safe Protection
• TheTagAlertindicatorperformsasystemcheckduringoperation
 andincorporatesaFail-Safeprotectionmodetoalerttheuser
 shouldtheunitfailtofunctionproperly.
• IftheTagAlertindicatordetectsafaultytemperaturesensororthe
 temperatureexceedstheoperationallimits(70ºC(158ºF)to-20ºC
 (-4ºF))intransit,theunitwillenterintothismodeandwill
 discontinuetemperaturemeasurement.
• TheLCDwilldisplayblacksquaresoverthe“OK”.Nonumbers
 willbedisplayedontheLCD(Figure 3).
NOTE: If any numbers appear on the LCD, that alarm has
triggered. The “OK” may still be visible through the black
squares even if an alarm has triggered.
NOTE: Days are calculated in 24 hour increments. This begins when the start button is
rst pressed and the “OK” is displayed on the LCD.
Figure 1
Figure 2
Figure 4
Figure 5
Figure 3
/