Pro-Max GR14SPTK Specification

Brand
Pro-Max
Model
GR14SPTK
Category
Barbecues & grills
Type
Specification

This manual is also suitable for

1
®
®
®
®
SPLIT LID TABLE TOP TWO
SIDED GRILL
MODEL
CG14SPT, CG14STE, CG14SPTI, CG14SPTIG
GR14SPTA, GR14SPTC, GR14STE
GR14SPTK, GR14SPTI, GR14SPTIP
Installation and
Operation
Instructions
2M-Z5818 Rev. N 6/10/2010
GR14SPT
®
2
2
These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual ac-
companying the appliance.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
NOTICE
Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.
Star reserves the right to change specications and product design without
notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.
Due to periodic changes in designs, methods, procedures, policies and
regulations, the specications contained in this sheet are subject to change
without notice. While Star Manufacturing exercises good faith efforts to provide
information that is accurate, we are not responsible for errors or omissions
in information provided or conclusions reached as a result of using the
specications. By using the information provided, the user assumes all risks in
connection with such use.
MAINTENANCE AND REPAIRS
Contact your local authorized service agent for service or required maintenance. Please record
the model number, serial number, voltage and purchase date in the area below and have it ready when you call to ensure
a faster service.
SAFETY SYMBOL
Model No.
Serial No.
Voltage
Purchase Date
Business 8:00 am to 4:30 p.m. Central Standard Time
Hours:
Telephone: (800) 807-9054 Local (314) 781-2777
Fax: (800) 396-2677 Local (314) 781-2714
E-mail [email protected]
[email protected]
[email protected]
Website: www.star-mfg.com
Service Help Desk
Authorized Service Agent
Reference the listing provided with the unit
or
for an updated listing go to:
Website: www.star-mfg.com
E-mail [email protected]
Telephone: (800) 807-9054 Local (314) 781-2777
Mailing Address: Star International Holdings Inc., Company
10 Sunnen Drive
St. Louis, MO 63143
U.S.A
3
GENERAL SPECIFICATIONS
B
C
A
D
IL1378
FIRST OPEN POSITION FULL OPEN POSITION
Model No Grill Surface (A) Width
Inches
(cm)
(B) Depth
Inches
(cm)
(C) Closed Inches
(cm) (D) Open Inches
(cm) Voltage Wattage Amps NEMA Plug
Approximate Weight
Shipping
lbs. (kg) Installed
lbs. (kg)
CG14SPT-120C
Aluminum
16”
(40.6) 23 1/8”
(58.7)
14 1/4” (36.3) 31 5/8” (80.3) 120 2,300 19.2 5-30P
81 (37.8) 68 (30.9)
CG14SPT-120V 14 1/4” (36.3) 31 5/8” (80.3) 120 2,300 19.2 5-20P
CG14SPT-230V 14 1/4” (36.3) 31 5/8” (80.3) 230 2,112 9.2 IEC 320
CG14SPT-240V 14 1/4” (36.3) 31 5/8” (80.3) 240 2,300 9.6 6-15P
CG14SPTI-240
Iron
17 1/4” (43.8) 34 5/8” (87.9) 240 3,550 14.8 6-20P
CG14SPTI-ARB 17 1/4” (43.8) 34 5/8” (87.9) 240 3,550 14.8 6-20P
CG14SPTID240 17 1/4” (43.8) 34 5/8” (87.9) 240 3,550 14.8 6-20P
CG14SPTIG240 17 1/4” (43.8) 34 5/8” (87.9) 240 3,550 14.8 6-20P
CG14SPTK-120
Aluminum
14 1/4” (36.3) 31 5/8” (80.3) 120 2,300 19.2 5-20P
CG14SPTK120C 14 1/4” (36.3) 31 5/8” (80.3) 120 2,300 19.2 5-30P
CG14SPTK240 14 1/4” (36.3) 31 5/8” (80.3) 240 2,300 9.6 6-15P
CG14STKE-120 14 1/4” (36.3) 31 5/8” (80.3) 120 2,300 19.2 5-20P
GR14SPTA-120 14 1/4” (36.3) 31 5/8” (80.3) 120 2,300 19.2 5-20P
GR14SPTA120C 14 1/4” (36.3) 31 5/8” (80.3) 120 2,300 19.2 5-30P
GR14SPTA-240 14 1/4” (36.3) 31 5/8” (80.3) 240 2,300 9.6 6-15P
GR14SPTA-CE 14 1/4” (36.3) 31 5/8” (80.3) 230 2,110 9.2 IEC 320
GR14SPTC-120 Chrome 17 1/4” (43.8) 34 5/8” (87.9) 120 2,300 19.2 5-20P
GR14SPTC-240 17 1/4” (43.8) 34 5/8” (87.9) 240 2,300 9.6 6-15P
GR14SPTI-240 Iron 17 1/4” (43.8) 34 5/8” (87.9) 240 3,550 14.8 6-20P
GR14SPTIP240 17 1/4” (43.8) 34 5/8” (87.9) 240 3,220 14.8 6-20P
GR14SPTK-120
Aluminum
14 1/4” (36.3) 31 5/8” (80.3) 120 2,300 19.2 5-20P
GR14SPTK120C 14 1/4” (36.3) 31 5/8” (80.3) 120 2,300 19.2 5-30P
GR14SPTK-240 14 1/4” (36.3) 31 5/8” (80.3) 240 2,300 9.6 6-15P
GR14STE-120 14 1/4” (36.3) 31 5/8” (80.3) 120 2,300 19.2 5-20P
GR14STE-120V 14 1/4” (36.3) 31 5/8” (80.3) 120 2,300 19.2 5-20P
GR14STKE-120 14 1/4” (36.3) 31 5/8” (80.3) 120 2,300 19.2 5-20P
GR14SPTG-240 14 1/4” (36.3) 31 5/8” (80.3) 240 2,300 9.6 6-15P
GR14SPTG-120 14 1/4” (36.3) 31 5/8” (80.3) 120 2,300 19.2 5-20P
4
GENERAL INSTALLATION DATA
This equipment is designed and sold for commercial use only by personnel trained and experienced
in its operation and is not sold for consumer use in and around the home nor for use directly by the
general public in food service locations.
Before using your new equipment, read and understand all the instructions & labels associated with
the unit prior to putting it into operation. Make sure all people associated with its use understand the
units operation & safety before they use the unit.
All shipping containers should be checked for freight damage both visible and concealed. This
unit has been tested and carefully packaged to insure delivery of your unit in perfect condition. If
equipment is received in damaged condition, either apparent or concealed, a claim must be made
with the delivering carrier.
Concealed damage or loss - if damage or loss is not apparent until after equipment is unpacked, a
request for inspection of concealed damage must be made with carrier within 15 days. Be certain to
retain all contents plus external and internal packaging materials for inspection. The carrier will make
an inspection and will supply necessary claim forms.
INSTALLATION
1. This two sided grill is equipped for the voltage shown on the nameplate. It will operate on alternating
current only, however the specied voltage must be applied.
2. 120 volt units must be plugged into a dedicated 120 VAC line with a 20 Amp receptacle.
230-240 volt units do not require a dedicated 240 VAC circuit with a 15 Amp receptacle.
DO NOT CONNECT THE UNIT TO ANY TYPE OF VOLTAGE OTHER THAN THAT ON THE
NAMEPLATE. DOING SO WILL DAMAGE THE UNIT AND VOID THE WARRANTY.
INITIAL START UP
Level unit using the adjustable feet under the unit (approximately 1/2" adjustment).
Before using the unit for the rst time, wipe down the exterior and toasting area with a damp cloth.
Take to a well ventilated area and heat for approximately 30 minutes. The grill may emit a small
amount of smoke as the cooking surfaces reach 450°F (232°C). Do not be alarmed, as the smoke is
caused by oils associated with the manufacturing process and will stop when the burn off is complete.
Brush off any debris from the toasting surface.
SEASONING THE COOKING SURFACES (NON CHROME SURFACES)
FIRST TIME SEASONING
Follow your company/corporate guidelines for seasoning cooking surfaces. or
1. Bring the grill to 300°F (149°C) and leave it on while doing the next two steps.
2. Brush the cooking surfaces with a SALT-FREE release agent.
If using an aerosol agent, rst apply into a cup and then brush onto cooking surface.
3. Let sit for 20 minutes, and then wipe clean using a warm damp cloth.
DAILY SEASONING
The grill should not require much seasoning while in use. In most cases, brush a light coating of a
SALT-FREE baking release agent in the morning and occasionally throughout the day will be enough
to prevent any sticking. It is not necessary to brush before grilling each item.
PRESET TIME AND TEMPERATURE
If adjustments are required, please refer to the time or temperature programming section in this
manual.
°F/°C CONVERSION
To change the temperature display from °F to °C or from °C to °F, hold the TEMP button while the
unit is turned off. While holding the TEMP button, turn the unit on. The display will be the changed
temperature mode. To change back, repeat the procedure.
CAUTION
WARNING
5
OPERATING INSTRUCTIONS
1. Turn unit on by placing switch in "ON" position. The "Heat On" indicator, program number and
display will ash indicating unit is heating. When the preset temperature is reached, the heating
light, display and program light indicator will stop ashing followed by 3 beeps. (Initial startup
heating time is approximately 30 minutes).
2. Place product on the bottom cooking surface of the unit and close the lids.
3. Press program button and let displayed time count down to "0" at which time unit will beep.
To turn off the beeper, press program button again.
4. Raise lids until it engages into rst indent and remove food. Using spatula, scrape residue into
grease catcher tray.
Note: Metal utensils with rounded corners may be used, however, using nonmetal utensils will
prolong the life of the cooking surface.
5. Turn the unit off when not in use.
TEMPERATURE/TIMER CONTROLLER OPERATION SPECIFICATIONS
Startup:
1. The preset time will ash until preset temperature is reached.
2. When the control reaches preset temperature, time display, "Heat On" indicator and program
indicator will stop ashing and the alarm will beep three times.
Temperature:
1. To view the actual temperature, press and hold "Temp Button." Display will read "Lo F" if temperature
is below 273°F (134°C) and "Hi F" if temperature is above 573°F (301°C).
To Program Time and Temperature:
1. Press and hold "TEMP" (actual temperature displays).
2. While holding "TEMP," press and hold any program button on the Left one second, the LED
above the program number light and the display reads "_ _ _ _." Enter the four-digit security code
sequence, 4, 3, 2, 1. The security code will not show on the display. Once the correct sequence
has been entered, the preset time will be displayed and the LED for that program will begin to
ash.
3. Set the time with the "+ or -" buttons.
4. Press the "TEMP" button to save the time.
5. The preset temperature will now be displayed.
6. Set the desired temperature for this program using the "+ or -" buttons.
7. Press the "TEMP" button to save temperature and to exit programming mode for this program.
The LED will stop ashing but will remain lit.
8. Press any other program button within 15 seconds to continue programming without re-entering
the security code.
9. While programming a program (LED is ashing), if no input is received for 15 seconds, the unit
will revert to normal operation and the security code must be re-entered.
Note: Temperature settings are done with the left side buttons only. The time settings
programmed on the Left buttons will also be programmed onto the right side. See below to make
time changes to the right side only. Each programming change must be saved by pressing the
"TEMP" button!
6
Right Side (Timer only):
1. To Change the time on the right side, press and hold the "TEMP" button, and press and hold any
program button on the right for one second. The LED above the program button will light and
the Right Display will read "_ _ _ _." Enter the four-digit security code sequence, 4, 3, 2, 1. The
security code will not show on the display. Once the correct sequence has been entered, the
preset time will be displayed and the LED for that program will begin to ash.
2. Set the time with the "+ or -" buttons.
3. Press the "TEMP" button to save the time.
4. The LED will stop ashing but will remain lit.
5. Press any other program button within 15 seconds to continue programming without re-entering
the security code.
6. While programming a program (LED is ashing), if no input is received for 15 seconds, the unit
will revert to normal operation and the security code must be re-entered.
Operation:
1. Pressing any program button (1-4) will start the timer countdown and display the preset time
remaining. The LED for the appropriate program will be lit during countdown and remain lit until
another program is selected.
2. When the display reaches "00:00", the buzzer will sound and the digits will ash.
3. Press the program button to silence the buzzer and return the readout to programmed time.
4. The right and left sides will operate independently of each other. Both timers can be in operation
at the same time. The "00:00" display will show which side is timed out.
MONTHLY INSPECTION
Check all bolts/screws and tighten if necessary.
CLEANING (NON-CHROME SURFACES)
Begin cleaning procedure by using the operating procedures within your organization, or follow the
steps below:
1. If particles adhere to the cooking surface during the day, scrape them off with a spatula.
NOTE: It is best not to let food residue onto the grill, as food build-up on the grill will increase sticking
and smoking. In addition, carbon may build up on the grill surface and reduce the cooking efciency.
CARBON BUILDUP: A black matter that forms on or near the cooking surface. Generally this is a
combination of: releasing agents, oils, food particles etc. that has cooked itself to the surface. After a
period of time without cleaning, this will reduce performance and material may start aking off. When
that happens, follow the "Carbon Cleaning" procedures.
2. At the end of the day, wipe down all surfaces with a warm, damp cloth and mild detergent, then
dry.
CARBON CLEANING
When carbon build up occurs, use a carbon removal agent (safe for aluminum & chrome surfaces)
according to the instructions provided with the cleaner. When this process is complete, you must re-
season the grill according to your company/corporate guidelines, or the seasoning instructions in this
manual.
DO NOT IMMERSE OR LET THE UNIT STAND IN WATER. DO NOT HOSE DOWN THE UNIT.
KEEP THE UNIT AWAY FROM RUNNING WATER.
DO NOT SPLASH THE CONTROL HOUSING! DO NOT SPLASH THE CONDUIT
CONNECTING THE TOP AND BOTTOM OF THE GRILL!
DO NOT USE ICE ON COOKING SURFACE!
BEFORE CLEANING ALL OTHER UNITS MAKE SURE POWER IS TURNED OFF AND UNIT
IS UNPLUGGED.
CAUTION
WARNING
7
To remove burned on grease or food residue use the following mixture:
1 Tablespoon liquid dish detergent
1 Cup of warm water
While holding top lid with one hand, apply this mixture to cold or warm top cooking surface with a
sponge or plastic scrubbing pad. Wipe with clean sponge or towel until it is clean.
Empty and clean grease catcher tray as required using detergent and water after removing tray from
unit.
CLEANING (CHROME SURFACES)
It takes very little time and effort to keep this Industrial Chromium griddle surface sparkling clean and
performing at top efciency. DO NOT allow grease to accumulate as it will carbonize and become
difcult to remove. To prevent this condition the following cleaning suggestions should be followed:
1. Remove excess grease and food regularly with a 4” (100mm) wide Razor Sharp type scraper with
rounded corners and wipe surface with a damp cloth if desired.
2. Following the scraping, for end of the day cleaning, a damp cloth and a non-silicated, non-abrasive,
non-chlorinated cleaner such as Bon-Ami may be used to wipe surface clean, followed by wiping
with a clean wet cloth.
3. Use a clean cloth and good non-abrasive cleaner to clean the (NON COOKING SURFACES)
stainless steel body of the griddle. Wipe the control panel front with a soft cloth.
4. At least once a day, remove the waste drawer and wash in the same way as an ordinary cooking
utensil. The drawer is removed by pulling forward and out.
1. Never use pumice, griddle stones, or abrasives on a chromium surface.
2. Never strike a chromium griddle surface with a sharp instrument or spatula edge.
3. Never use steel wool.
4. Never use commercial liquid grill cleaner on the griddle surface.
5. Abusing surface voids the warranty.
CHROME SURFACE LIMITED WARRANTY EXCLUSIONS
Your Chrome Two Sided Grill has been designed to give you many years of cooking reliability and
requires minimum maintenance to keep the chrome surface in its original condition. All Chrome
surfaces are warranted for a period of 1 years against manufacturing defects to the original owner
from the date of installation. This limited warranty is void if it is determined by Star Manufacturing
International Incorporated or one of its authorized representatives that the chrome surface has been
misused or abused or subjected to the following situations:
1. Improperly installed.
2. Incorrect voltage applied to electric Pro-Max units allowing the surface to overheat and discolor.
3. The misuse of any instrument or tool which scratches or makes indentations in the surface which
could cause the surface to peel, ake, or chip off.
4. The use of any chemical or abrasive cleaning solution, griddle brick, stone, screen or other cleaning
products which could damage and affect the performance of the chrome surface.
5. The neglect of daily routine maintenance to the chromium surface.
CAUTION
CAUTION
8
Part# 2M-4497-2 05/06 RB
The foregoing warranty is in lieu of any and all other warranties expressed or implied and constitutes the entire warranty.
FOR ASSISTANCE
Should you need any assistance regarding the Operation or Maintenance of any Star equipment; write, phone, fax or email our Service Department.
In all correspondence mention the Model number and the Serial number of your unit, and the voltage or type of gas you are using.
ALL:
* Pop-Up Toasters
* Butter Dispensers
* Pretzel Merchandisers
* Pastry Display Cabinets
* Nacho Chip Merchandisers
* Accessories of any kind
* Sneeze Guards
* Pizza Ovens
* Heat Lamps
* Pumps
Visit our Website at: www.star-mfg.com Email: [email protected]
THOROUGHLY INSPECT YOUR UNIT ON ARRIVAL
This unit has been tested for proper operation before leaving our plant to insure delivery of your unit in perfect condition. However, there are instances in
which the unit may be damaged in transit. In the event you discover any type of damage to your product upon receipt, you must immediately contact the
transportation company who delivered the item to you and initiate your claim with same. If this procedure is not followed, it may affect the warranty
status of the unit.
LIMITED EQUIPMENT WARRANTY
All workmanship and material in Star products have a one (1) year limited warranty on parts & labor in the United States and Canada. Such warranty is
limited to the original purchaser only and shall be effective from the date the equipment is placed in service. Star's obligation under this warranty is limited
to the repair of defects without charge, by the factory authorized service agency or one of its sub-agencies. Models that are considered portable (see below)
should be taken to the closest Star service agency, transportation prepaid.
>Star will not assume any responsibility for loss of revenue.
>On all shipments outside the United States and Canada, see International Warranty.
*The warranty period for the JetStar six (6) ounce & Super JetStar eight (8) ounce series popcorn machines is two (2) years.
*The warranty period for the Chrome-Max Griddles is five (5) years on the griddle surface. See detailed warranty provided with unit.
* The warranty period for Teflon/Dura-Tec coatings is one year under normal use and reasonable care. This warranty does not apply if damage occurs to
Teflon/Dura-Tec coatings from improper cleaning, maintenance, use of metallic utensils, or abrasive cleaners. This warranty does not apply to the
“non-stick” properties of such materials.
>This warranty does not apply to "Special Products" but to regular catalog items only. Star's warranty on "Special Products" is six (6) months on parts
and ninety (90) days on labor.
>This warranty does not apply to any item that is disassembled or tampered with for any purpose other than repair by a Star Authorized Service Center or
the Service Center's sub-agency.
>This warranty does not apply if damage occurs from improper installation, misuse, wrong voltage, wrong gas or operated contrary to the Installation and
Operating instructions.
>This warranty is not valid on Conveyor Ovens unless a "start-up/check-out" has been performed by a Factory Authorized Technician.
PARTS WARRANTY
Parts that are sold to repair out of warranty equipment are warranted for ninety (90) days. The part only is warranted. Labor to replace the part is
chargeable to the customer.
SERVICES NOT COVERED BY WARRANTY
PORTABLE EQUIPMENT
Star will not honor service bills that include travel time and mileage charges for servicing any products considered "Portable" including items listed below.
These products should be taken to the Service Agency for repair:
1. Travel time and mileage rendered beyond the 50 mile radius limit
2. Mileage and travel time on portable equipment (see below)
3. Labor to replace such items that can be replaced easily during a daily cleaning
routine, ie; removable kettles on fryers, knobs, grease drawers on griddles, etc.
4. Installation of equipment
5. Damages due to improper installation
6. Damages from abuse or misuse
7. Operated contrary to the Operating and Installation Instructions
8. Cleaning of equipment
9. Seasoning of griddle plates
10. Voltage conversions
11. Gas conversions
12. Pilot light adjustment
13. Miscellaneous adjustments
14. Thermostat calibration and by-pass adjustment
15. Resetting of circuit breakers or safety controls or reset buttons
16. Replacement of bulbs
17. Replacement of fuses
18. Repair of damage created during transit, delivery, &
installation OR created by acts of God
*The Model 510FD Fryer.
*The Model J4R, 4 oz. Popcorn Machine.
* The Model 518CMA & 526CMA Cheese Melter.
*The Model 12MC & 15MC & 18MCP Hot Food Merchandisers.
*The Model 12NCPW & 15NCPW Nacho Chip/Popcorn Warmer.
*All Hot Dog Equipment except Roller Grills & Drawer Bun Warmers.
*All Nacho Cheese Warmers except Model 11WLA Series Nacho Cheese Warmer.
*All Condiment Dispensers except the Model HPDE, & SPDE Series Dispenser.
*All Specialty Food Warmers except Model 130R, 11RW Series, and 11WSA Series.
*All QCS/RCS Series Toasters except Model QCS3 & RCS3 Series.
9
WIRE DIAGRAM
120V/240V, 2300 WATT
240V, 3550 WATT
(2J-Z6323 CONTROLLER ONLY)
STAR MANUFACTURING INTERNATIONAL, INC.
GR14SPTA-240V
GR14SPTK-120C
GR14SPTI-240V SK2078 REV. A 12/28/06
MODEL CG14SPT-120V
CG14SPT-240V
CG14SPTI-240V
GR14SPTA-120V
4
8
6 2
1 0
BA
C
D
SENSOR - RIGHT
(SENSORIO)
BOTTOM ELEMENT
(ELEMENTO MAS BAJO)
TOP ELEMENT
RIGHT
(ELEMENT MAS ALTO)
GREEN
BLACK
WHITE
E4
E3 E1
E5E6
13
2
15
16
13 14
65
3
4
21
4
10
9
10
9
8
77
8
11
12
11 12
14
15
13
16
REAR OF CONTROLLER
E2
E11
E12
SENSOR - LEFT
(SENSORIO)
TOP ELEMENT
LEFT
(ELEMENT MAS ALTO)
TRANSFORMER
(TRANSFORMADOR)
RELAY
(RELE)
TERMINAL BLOCK
(BLOQUE TERMINAL)
FOR REFERENCE
WIRING DIAGRAM IS SHOWN AS UNIT IS ASSEMBLED
WITH THE BOTTOM PLATE REMOVED. THE TOP
DESCRIPTIONS ARE THEIR POSITIONS WHEN UPRIGHT.
1 0
84
6 2
SWITCH
(INTERRUPTOR)
5
6
E7
120V UNITS PLUG
NEMA 5-20P 2,300 WATT
NEMA 5-30P 2,300 WATT
240V UNITS PLUG
NEMA 6-15P 2,300 WATTS
NEMA 6-20P 3,550 WATTS
CERTAIN INSTANCES MAY NOT BE AVAILABLE
ILLUSTRATIVE PURPOSES ONLY AND IN
SOME ITEMS ARE INCLUDED FOR
10
4
8
6 2
10
BA
C
D
SENSOR - RIGHT
(SENSORIO)
BOTTOM ELEMENT
(ELEMENTO MAS BAJO)
TOP ELEMENT
RIGHT
(ELEMENT MAS ALTO)
GREEN / YELLOW
STRIPE
BROWN
BLUE
BS 1363A PLUG
(13 AMP)
E4E3 E1
E5E6
13
2
15
16
13 14
65
3
4
21
4
10
9
10
9
8
77
8
11
12
11 12
14
15
13
16
REAR OF CONTROLLER
E2
E11
E12
SENSOR - LEFT
(SENSORIO)
TOP ELEMENT
LEFT
(ELEMENT MAS ALTO)
TRANSFORMER
(TRANSFORMADOR)
RELAY
(RELE)
TERMINAL BLOCK
(BLOQUE TERMINAL)
FOR REFERENCE
WIRING DIAGRAM IS SHOWN AS UNIT IS ASSEMBLED
WITH THE BOTTOM PLATE REMOVED. THE TOP DESCRIPTIONS ARE THEIR POSITIONS WHEN UPRIGHT.
1 0
84
6 2
SWITCH
(INTERRUPTOR)
5
6
E7
INLET IEC 320 16A
230V UNITS
18
19
20 G
L
N
CERTAIN INSTANCES MAY NOT BE AVAILABLE
ILLUSTRATIVE PURPOSES ONLY AND IN
SOME ITEMS ARE INCLUDED FOR
WIRE DIAGRAM, 230V, 2300 WATT
(2J-Z6323 CONTROLLER ONLY)
MODEL:
GR14SPTA-UK-230V, 2300 WATT
THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.
NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.
STAR MANUFACTURING INTERNATIONAL INC.
SK2017 Rev A 08/10/2004
11
STAR MANUFACTURING INTERNATIONAL, INC.
SK2336 REV. - 12/7/07
MODEL: GR14SPTIP240
4
8
6 2
1 0
BA
C
D
SENSOR - RIGHT
(SENSORIO)
BOTTOM ELEMENT
(ELEMENTO MAS BAJO)
TOP ELEMENT
RIGHT
(ELEMENT MAS ALTO)
GREEN
BLACK
WHITE
E4
E3 E1
E5E6
13
2
15
16
13 14
65
3
4
21
4
77
8
14
15
13
16
REAR OF CONTROLLER
E2
E11
E12
SENSOR - LEFT
(SENSORIO)
TOP ELEMENT
LEFT
(ELEMENT MAS ALTO)
TRANSFORMER
(TRANSFORMADOR)
RELAY
(RELE)
TERMINAL BLOCK
(BLOQUE TERMINAL)
FOR REFERENCE
WIRING DIAGRAM IS SHOWN AS UNIT IS ASSEMBLED
WITH THE BOTTOM PLATE REMOVED. THE TOP
DESCRIPTIONS ARE THEIR POSITIONS WHEN UPRIGHT.
1 0
84
6 2
SWITCH
(INTERRUPTOR)
5
6
E7
120V UNITS PLUG
NEMA 5-20P 2,300 WATTS
NEMA 5-30P 2,300 WATTS
240V UNITS PLUG
NEMA 6-15P 2,300 WATTS
NEMA 6-20P 3,550 WATTS
8
17
17
CERTAIN INSTANCES MAY NOT BE AVAILABLE
ILLUSTRATIVE PURPOSES ONLY AND IN
SOME ITEMS ARE INCLUDED FOR
WIRE DIAGRAM
12
This drawing contains information confidential
to Star Manufacturing International, Inc.
No reproduction or disclosure of its
CERTAIN INSTANCES MAY NOT BE AVAILABLE
ILLUSTRATIVE PURPOSES ONLY AND IN
SOME ITEMS ARE INCLUDED FOR
contents is permitted.
STAR MANUFACTURING INTERNATIONAL, INC.
SK1901 REV. F 4/27/2010
MODEL CG/GR14SPT
60
56
58
59
55
53
54
52
16
10
11
8
11
7
6
17
2
4
1
9
9
20
19
18
57
3
NAMEPLATE
5
20
22
21 24
3
22
51
49
47
48
61
62
64 63
4“ LEGS ONLY
70
38
50
48
41
42
39
43
40
32
46
44 45
34
36
37 35
33
30
69
14
13
15
12
31 25
28
26
29 57
23
27
13
CG14SPT, CG14SPTIG-120V, 120C, 230V & 240V, CG/GR14STE
GR14SPTA, GR14SPTC, GR14SPTK-120V, 120C, 230V & 240V
CG/GR14SPTI-240V, GR14SPTIP240 Split Lid Table Top Grill
PARTS LIST June 10, 2010, Rev N
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1
INCLUDE MODEL AND SERIAL NUMBER OF 4
Some items are included for illustrative purposes only and in certain instances may not be available.
MODEL
Star Manufacturing International, Inc.
Item
No Part No Qty Description Application
1 2M-Z2620 2 LABEL CAUTION, BI-LINGUAL
2 2C-Z3200 4 PIN - TOP HOUSING
3 2A-Z3827 2 PLATE, STAMPING CONDUIT
4D9-GR0181 2 TOP HOUSING & CONDUIT ASSEMBLY
D9-Z11716 1TOP HOUSING, LT SPLT CG14STKE-120, GR14STB, GR14STE,
GR14STKE120C
D9-Z11717 TOP HOUSING, RT SPLT
5 2C-Z5883 8 10-24 X 1/2” FZA SCREW, TOP HOUSING
6 B9-04-WB-0046 2 CLAMP WIRE SUPPORT
7 D9-GR0182 2 TOP RETAINING PLATE ASSEMBLY
8 D9-Z2133 2 INSULATION FIBERGLASS TOP
92A-Z6604 12 SPACER - INSULATION PLATE
2A-Z9514 SPTC, SPTI
10 D9-Z3902 2 PLATE - TOP ELEMENT RETAINING
D9-Z9513 SPTC, SPTI
11 PS-Z9325 2ELEMENT, HEATING, TOP 500W 120V
PS-Z9326 ELEMENT, HEATING, TOP 500W 230/240V SPT, SPTA, SPTC, SPTA, SPTG 230/240V
PS-Z9521 2 ELEMENT, HEATING, TOP 700W SPTI
12 2C-Z3350 2 HALF CLAMP - .188 DIAMETER
13 D9-Z3903 2 BRACKET, PROBE MOUNT
14 2E-Z3278 2 RTD PROBE - 48” LONG WIRE - THERMISTOR
15
PS-GR0356
2
KIT, 2F-Z3237 CASTING REPLACMENT SMOOTH - ALUM
PS-GR0355 KIT, 2F-Z5615 CASTING REPLACMENT GROOVED - ALUM
PS-GR0504 KIT, 2F-Z5615 COATED CASTING REP. GROOVED - ALUM
2F-Z9651 CASTING - TOP SMOOTH, CHROME
2F-Z8349 CASTING - TOP SMOOTH, IRON
2F-Z7967 CASTING - TOP GROOVE, IRON
16 2V-Z3152 2 HANDLE
17
2B-Z3336 414” CG14SPT ARM
2B-Z9515 ARM SPTC, SPTI
2B-Z10355 ARM CG14SPTK-120/240V
2B-Z12554 2ARM, LEFT ST CG14STKE-120, GR14STB, GR14STE,
GR14STKE120C
2B-Z12555 ARM, RIGHT ST CG14STKE-120, GR14STB, GR14STE,
GR14STKE120C
18 2C-08-07-0040 12 ACORN NUT, 1/4-20 ACHD STL NP
19 2C-08-07-0262 8 WASHER 1/4 INT STL NP
20 2C-Z2992 12 BOLT 1/4-20X1 PHP STL NP
21 2C-Z3917 4 RIVET, POP,
22 2E-Z2898 2 CONDUIT ASSEMBLY
23 2E-Z3768 2 LOCKNUT, CONDUIT 1/2”
24 2C-Z3780 4 RETAINER, CONDUIT
25 2V-Z3252 2 TOP HOUSING LATCH ROD
26 2A-Y6142 4 SLEEVE HANDLE
27 2C-1516 4 SCREW 10-24 X 1” STL RH NP, LATCH ROD
14
PARTS LIST June 10, 2010, Rev N
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 2
INCLUDE MODEL AND SERIAL NUMBER OF 4
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing International, Inc.
CG14SPT, CG14SPTIG-120V, 120C, 230V & 240V
GR14SPTA, GR14SPTC, GR14SPTK-120V, 120C, 230V & 240V
CG/GR14SPTI-240V, GR14SPTIP240 Split Lid Table Top Grill
MODEL
Item
No Part No Qty Description Application
28 2R-Z3345 1 COUNTER BALANCE - SPLIT TOP
29 2C-Z2593 4 SCREW - 10-24X1 1/2 SL HX/W NP
30 D9-Z11677 1 INSULATION BAFFLE ASSEMBLY
31 D9-Z3826 1 INSULATION - BAFFLE
32 2A-Z6484 2 PLATE (COUNTER BALANCE MOUNT)
33
D9-GR0152
1BODY ASSEMBLYD9-GR0393 CG14SPTK-120/240V
D9-GR0394 GR14SPTIP
D9-GR0507 BODY ASSY - 14” CG/CG14 GR14STE
D9-GR0461 BODY ASSY 14” SPT GR14STB
34
2M-Z5817
1
OVERLAY-STANDARD CG14SPT, CG14SPTI, GR14SPTA, GR14SPTC,
GR14SPTI, GR14SPB,. GR14STE
2M-Z3337
OVERLAY
GR14SPT-120/240V & CUL
2M-Z10851 CG14SPTK-120/240V
2M-Z11984 GR14STE-120
2M-Z11983 GR14STE-120V
35 Z1-70-07-0343 1 SWITCH GUARD
36 2M-12-07-0038 1 LABEL ON & OFF
37 2I-05-07-0013 1 BOOT SWITCH
38 D9-GR0518 1 GREASE DRAWER ASSEMBLY CG14SPTK
D9-GR0517 GR14SPTKG120
39 2E-Z3808 1 SWITCH TOGGLE
40 2J-Z6323 1TIME/TEMPERATURE CONTROL
D9-GR0387 CONTROL PROGRAMMING CG14SPTK-120/120C/240V
D9-GR0380 CONTROL PROGRAMMING GR14SPTK-120/120C, GR14SPTKM120
41 2K-Z1971 14 SPACER
42 D9-GR0151 1FACEPLATE ASSEMBLY
D9-GR0382 FACEPLATE ASSEMBLY CG14SPTK
43 2E-Z3335 2 RELAY DOUBLE POLE-SINGLE THROW
44 2E-05-07-0350 1TRANSFORMER 230V/10V 6VA 230V
2E-05-07-0351 TRANSFORMER 115/10V 6VA
45 2E-Z2894 1 TERMINAL BLOCK (304)
46 D9-GR0156 1 REAR PLATE ASSEMBLY
47 D9-Z3259 1 BASE BOTTOM CG14SPTID240, GR14SPTA-CE
D9-Z10086
48 2A-Z11500 44” NON SKID FOOT BASE SPTC, SPTI
2A-Z11501 FOOT 1” SOLID RUBBER CG14SPTK, GR14SPTG
49 D9-GR0150 1 GREASE CABINET ASSEMBLY CG14SPTID240
D9-GR0034 GR14SPTA-CE
50 2K-Y6764 1 BUSHING 90 SR 17-2
15
PARTS LIST June 10, 2010, Rev N
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE
INCLUDE MODEL AND SERIAL NUMBER OF
Some items are included for illustrative purposes only and in certain instances may not be available.
3
4
Star Manufacturing International, Inc.
CG14SPT, CG14SPTIG-120V, 120C, 230V & 240V
GR14SPTA, GR14SPTC, GR14SPTK-120V, 120C, 230V & 240V
CG/GR14SPTI-240V, GR14SPTIP240 Split Lid Table Top Grill
MODEL
Item
No Part No Qty Description Application
51
2E-Z4119
1
CORD POWER 120V
D9-GR0193 CORD POWER 120C
D9-GR0194 CORD POWER 240V
CG14SPT-230V between 1-15-01 thru 8-16-04
2E-Y9251 CORD SET CONT EUR 16AMP CG14SPT-230V
2E-Z2905 CORD POWER SPTI- 240V
52 D9-GR0189 2 TOP BURN GUARD ASSEMBLY
53
D9-GR0177
1
BURN GUARD ASSEMBLY - LEFT
D9-GR0501 BURN GUARD, LT WELD ASSY CG14STKE-120, GR14STB, GR14STE,
GR14STKE120C
D9-GR0335 CG14SPTI-230
54
D9-GR0176
1
BURN GUARD ASSEMBLY - RIGHT
D9-GR0500 BURN GUARD, RT WELD ASSY CG14STKE-120, GR14STB, GR14STE,
GR14STKE120C
D9-GR0334 CG14SPTI-230
55
PS-GR0361
1
KIT, 2F-Z1945, CASTING SM REPLACMENT GR SERIES (NON-SPTI)
PS-GR0362 KIT, 2F-Z1947, CASTING GR REPLACMENT CG SERIES (NON-SPTI)
PS-GR0503 KIT, 2F-Z1947, COATED CASTING GR REPL CG SERIES (NON-SPTI)
2F-Z9653 CASTING - SMOOTH BOTTOM, CHROME SPTC
PS-GR0363 KIT, 2F-Z1949, CSTNG - BOTTOM, IRON GR14SPTI
PS-GR0364 KIT, 2F-Z1951, CSTNG - GROOVE, IRON CG14SPTI
56
2N-Z9324 1ELEMENT, HEATING, BTM 120V
2N-Z9327 ELEMENT, HEATING, BTM 1300 W 230V-240V (NON-SPTI)
2N-Z9520 ELEMENT, HEATING, BTM 2150 W SPTI 230/240V
2N-Z11709 2 ELEMENT, 650 WATT, 120V CG14STKE, GR14STE, GR14STKE
57 2C-08-07-0285 12 SCREW 10-24 x 3/4 x 3/8
58 D9-Z2618 1BOTTOM ELEMENT RETAINING PLATE
D9-Z9701 BOTTOM ELEMENT RETAINING PLATE SPTC
59 D9-Z2888 1 INSULATION - 14”
60 D9-Z2619 1 BOTTOM INSULATION RETAINING PLATE
61 2V-Z3027 2 CROSS SUPPORT SPTC, SPTI
62 D9-Z9516 2 SUPPORT BRACKET, LEGS SPTC, SPTI
63 2C-08-07-0262 4 WASHER 1/4 INT STL NP SPTC, SPTI
64 2C-Z2992 4 BOLT 1/4-20X1 PHP STL NP SPTC, SPTI
65 2T-6447 1 THERMOSTAT 118V-236V SPTIP
66 2M-Z11301 1 LABEL - DIAL SPTIP
67 2R-Z4621 1 KNOB, 1-3/4 - .250”D”HOLE SPTIP
68 D9-Z11304 1 PLATE, COVER SPTIP
69 PS-GR134 AR KIT, BEARING ASSY, COUNTER BALANCE
16
PARTS LIST June 10, 2010, Rev N
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 4
INCLUDE MODEL AND SERIAL NUMBER OF 4
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing International, Inc.
CG14SPT, CG14SPTIG-120V, 120C, 230V & 240V
GR14SPTA, GR14SPTC, GR14SPTK-120V, 120C, 230V & 240V
CG/GR14SPTI-240V, GR14SPTIP240 Split Lid Table Top Grill
MODEL
Item
No Part No Qty Description Application
70 D9-GR0520 1 BASE ASSY / GREASE CABINET
CG14SPT, CG14SPTI, CG14SPTIG, GR14SPTA,
GR14SPTC, GR14SPTI, GR14SPTIP, GR14STB,
GR14SPTE
D9-GR0522 CG14SPTK, CG14STKE, GR14SPTK,
GR14SPTKM120, GR14STKE
NI D9-Z11977 1 PLATE, BASE CONDUIT
CG142TB, CG14B, CG14E, CG14IB, CG14IGTB,
CG14ITB, CG14ITGTB, CG14ITLB, CG14ITSC,
CG14TB, GR14B, GR14E, GR14E, GR14IB, GR14ITB,
GR14SNB, GR14TB, CG14STKE, GR14STB,
GR14STE, GR14STKE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Pro-Max GR14SPTK Specification

Brand
Pro-Max
Model
GR14SPTK
Category
Barbecues & grills
Type
Specification
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents