Axor 06064XX0 User manual

Brand: Axor

Model: 06064XX0

Category: Sanitary ware

Type: User manual

Axor 06064XX0 is a thermostatic valve trim for a two-function shower. It has a lever handle that controls both temperature and volume, and a diverter button that switches the water flow between the showerhead and the tub spout. The valve also has a safety stop that prevents the water temperature from exceeding 100 degrees Fahrenheit (38 degrees Celsius).

C Cross

06066XX0

C Scroll

06065XX0

C Lever

06064XX0

Solaris² E

04147XX0

Allegro² E

04153XX0

Metro² E

04159XX0

Metris S

31317XX1

Focus S

31736XX1

Talis S

32317XX1

ThermoBalance II Rough & Trim

Installation Instructions / Warranty

ThermoBalance II Rough

06623000

ThermoBalance II Rough with Stops

06627000

Technical Specifications

Recommended pressure 45 - 72 psi

Maximum hot water temperature 165° F*

Recommended hot water temp. 120° - 140° F*

Nominal capacity @ 45 psi 8 gpm

Nominal capacity @ 60 psi 11.5 gpm

Safety stop 100° F

Maximum output temperature 110° F**

½” NPT connections

*Please know and follow all applicable local plumbing codes when setting the temperature on the water heater.

**The high temperature limit stop may be reset to comply with local plumbing codes. See page 11.

(For the sake of clarity, the plastic installation box

(i-box) is not shown in these illustrations. The

i-box should not be removed.)

Rough-in 06627000 has service (isolation)

stops built onto the valve. When the screw-

driver slots is horizontal, the stops are in the

“on” position. When the screwdriver slots are

vertical, the stops are in the “off” position.

When connecting the hot and cold supplies,

hold the stop steady with a wrench to avoid

stop mis-alignment, and breakage of the fac-

tory sealed thread compound.

The Service (Isolation) Stops

The cartridge shown is included

with the trim kit.

screwdriver

slots

English

Installation Considerations

For best results, this unit should be installed by a licensed, professional plumber.

Large pressure differences between the hot and cold supplies should be balanced.

Before beginning the installation, please read the instructions thoroughly. Inspect the

product and make sure that all parts are present and in good condition. If you have

questions, contact Hansgrohe Technical Services.

ThermoBalance II rough 06623000 does not include service stops. If service stops are

required by local plumbing code, order the stops separately (part #06900300) or order

ThermoBalance II rough 06627000, which incorporates service stops.

The ThermoBalance II is intended for use in a two-function shower. DO NOT plug any

outlet.

The ThermoBalance II rough must be used with a ThermoBalance II trim kit. Do not at-

tempt to use with any other trim kit.

Do not attempt to use this valve in combination with a diverter tub spout.

•

Installation Suggestions

Do not use a diverter tub spout!

Use for a two-feature installation only! Do not plug either outlet!

ok! ok!

no!

English

Install the ThermoBalance II Rough

Caution: Turn the water off at the supply before

proceeding.

Both outlets must be plumbed. Do

not plug any port.

Install the hot and cold supply lines to the rough.

The hot supply must be connected to the hot inlet

and the cold supply must be connected to the cold

inlet. If the supplies are not connected to the correct

inlets, the valve cannot work correctly.

(for the sake of clarity, the plastic installation box is

not shown in this illustration.)

If using model 06627000: When connecting

the hot and cold supplies, hold the stop steady with

a wrench to avoid stop mis-alignment, and break-

age of the factory sealed thread compound.

Install both outlet lines.

The valve should be level in all planes. It should

be installed so that the outside surface of the

finished wall falls between the minimum and maxi-

mum lines on the installation box. This will insure

that the trim fits properly.

English

Flush the supply lines using the flushing plug

When finishing the wall, install the wall material up

to the oval installation box.

Do not remove the installation box.

When the trim is installed, the plaster shield portion

of the installation box will be trimmed nearly flush

to the wall and sealed to provide protection against

water damage.

The installation box includes a flushing plug to

permit line flushing and pressure testing before

the cartridge and finishing parts are installed. A

pressure test of the installed piping should be per-

formed before the walls are closed.

The flushing plug permits cold water to flow from

the bottom outlet and the hot water through the top

outlet.

To flush the lines, install a hose bibb and hose

to each outlet line. (Using a hose will permit the

water to be directed to a location where it will

not cause damage.) Flush the lines for at least 5

minutes.

The porting in the flushing plug prevents cross flow.

However, it does not stop the flow of water through

the outlets.

English

These trim kits are for use with Thermo-

Balance II roughs 06623/06627 only.

Do not use with any other rough.

The finished wall must be complete and

made watertight before installation of

this trim kit.

These instructions cover these models:

Valve trim Shower set

only trim

C Lever 06064XX0 06082XX0

C Scroll 06065XX0 06083XX0

C Cross 06066XX0 06084XX0

Solaris² E 04147XX0 04150XX0

Allegro² E 04153XX0 04156XX0

Metro² E 04159XX0 04162XX0

Metris S 31317XX1 31324XX1

Focus S 31736XX1 31772XX1

Talis S 32317XX1 32324XX1

Solaris E 06636XX0 06642XX0

Stratos E 06580XX0 06586XX0

Metro E 06656XX0 06662XX0

06064XX0

06066XX0 06065XX0

04147XX0 04153XX0 04159XX0

31317XX1 31736XX1 32317XX1

06636XX0

06580XX0 06656XX0

English

Cut the plaster shield so that it extends 1/16”

outside the surface of the finished wall.

Remove the label. Cut the support arms that

connect the flushing plug to the installation box.

Remove the flushing plug. Do not discard the

screws.

Insert the cartridge in the rough. Make sure that

the locator tab on the cartridge goes straight into

the notch in the rough.

Use the flushing plug screws to connect the

cartridge retainer plate to the rough. Tighten the

screws evenly, using a manual screwdriver, in a

cross-wise pattern. Do not overtighten the screws.

Installation

Turn the water off at the main, or at the stops, before beginning.

Seal the wall around the i-box with

waterproof sealant.

Failure to seal the wall can lead to

possible water damage.

Be sure to remove the blue

flushing plug sealing gasket.

Failure to remove the gasket

can result in damage to the

cartridge and possible water

damage.

notch

locator

tab

English

All other models: Install two Duotec

strips directly on the carrier plate. Install

the remaining two strips on the back of the

escutcheon.

Turn on the water supplies. Grasp the stop unit

portion of the cartridge and turn it.

If there is a leak around the cartridge, turn the

supplies off, and remove the cartridge. Confirm

that the sealing gasket from the flushing plug was

removed.

Reinstall the cartridge. Turn the stop unit.

If the unit continues to leak, contact Hansgrohe

Customer Service for a replacement cartridge.

Perform the following test to check for damage to the ceramic

plates inside the stop unit.

Failure to correctly perform this test can result in possible water

damage.

Solaris oval escutcheon only: Install the

white spacers on the carrier plate (a). Install two

Duotec strips on the spacers (b).

Install the remaining two strips on the back of the

escutcheon.

stop unit

English

Install the carrier plate gasket and carrier plate

with the carrier plate screws.

Press the escutcheon very firmly over the carrier

plate, so that the strips of Duotec interlock, produc-

ing a very firm hold.

Install the handle: Tighten the handle screw,

using a 3 mm Allen wrench. For proper operation

of the valve, the handle screw must engage the

slot milled into the brass on the cartridge.

Set the high temperature limit stop (optional) -- see

page 11.

Justify the handle.

Justify the Handle

Tools required:

Thermometer

3 mm Allen wrench (included with trim kit)

Turn the valve on. Place the thermometer in the

water stream.

Turn the temperature control knob until the water

coming out measures 100° on the thermometer.

Turn the water off using the lever part of the

handle.

Use the 3 mm Allen wrench to loosen the set screw

on the bottom of the handle. Remove the handle

from the valve (1).

Hold the lever in one hand. With the other hand,

turn the temperature control knob approximately

½ turn clockwise (2a). Then, without pressing

inward on it, turn it counter-clockwise until it is

positioned vertically and hits the safety stop (2b).

Reinstall the handle and tighten the set screw (3).

English

User Instructions

The ThermoBalance II has two control features: the Temperature Selector and the Diverter /

Volume Control.

The Diverter/Volume Control handle controls the water flow.

The center position is “off”.

Turn the handle counter-clockwise to send

the water to outlet I (the bottom outlet).

Turn it clockwise to send the water to

outlet II (the top outlet).

The further you turn the handle from the

“off” position, the greater the water flow.

Turn the Temperature Selector counter

clockwise to make the water warmer.

It will stop when the water is 100° F

– this is the safety stop.

Override the safety stop by pressing in-

ward on the Temperature Selector and

continuing to turn it counter-clockwise.

Turn the Temperature Selector clockwise

to make the water cooler.

IMPORTANT: the Temperature Selector

will not automatically “reset” to below

100° when the water is turned off.

<100°100° >100°

English

Remove the clip and stop ring from the thermostatic cartridge stem. Put them in a safe

place.

Turn the thermostatic mixer stem with your fingers, clockwise to make the water cooler,

counter-clockwise to make the water warmer. Turn the stem until the water coming out is the

desired maximum high temperature – 110° in most areas.

Reinstall the stop ring so that it is against the stop. Reinstall the clip.

Justify and reinstall the handle.

Set the High Temperature Limit Stop (optional)

IMPORTANT: Many municipalities have codes limiting the maximum discharge temperature

of a shower valve to 110° F -- 112°F or less. In Massachusetts, the maximum output

temperature can be no higher than 112°F. Please know and follow all applicable local

codes when setting the high temperature limit stop.

Tools Required:

Thermometer

3 mm Allen wrench (included with trim kit)

Turn the hot and cold supplies to the valve on.

Turn the water on using the handle.

Use the 3 mm Allen wrench to loosen the set screw on the bottom of the handle. Remove

the handle.

English

Maintenance: Clean the filters

While holding the stop unit still, use a second ad-

justable wrench or a 17mm deep socket wrench to

unscrew and remove the thermostatic cartridge.

Rinse any debris from the filters on the thermostatic

cartridge. Use a soft toothbrush, if necessary.

Do not attempt to remove the screens.

Lubricate the o-rings with white plumbers grease.

Reinstall the thermostatic cartridge in the stop unit.

Justify and reinstall the handle.

CAUTION: Turn off the water to the shower, either

at the main or with the service stops, before open-

ing the valve.

Remove the handle and escutcheon.

Grasp the wrench flats on the cartridge stop unit

with an adjustable wrench.

Failure to hold the stop unit steady

while unscrewing or replacing the

thermostat cartridge will result in

damage to the stop unit.

wrench flat

stop unit

English

Page is loading ...

Troubleshooting

Problem Possible Cause Solution

Water leaks between cartridge

and rough

sealing ring from flushing plug still

inside rough

remove sealing ring

ceramic plate(s) inside cartridge

damaged

replace cartridge

Handle turns, but water does not

turn on/off

handle screw not tightened tighten handle screw

Water drips for several minutes

after the valve is turned off

normal clearing of showerhead not a problem

Water drips continuously after the

valve is turned off

ceramic plate(s) damaged replace cartridge

Water does not get hot/cold

enough

high temperature limit stop not set

properly

reset high temperature limit stop

handle not justified justify handle

thermostat cartridge is faulty replace thermostat cartridge

Temperature is erratic thermostat cartridge is faulty replace thermostat cartridge

Water pressure is poor filters on thermostat cartridge are

clogged

clean the filters

Unit outputs both hot and cold

water, but the water does not mix

not a product defect -- hot and

cold supplies are reversed

correct the plumbing

L’eau n’est pas assez chaude /

froide.

La butée limite d’eau chaude n’est

pas réglée.

Reprogrammez la butée limite

d’eau chaude.

La poignée n’est pas réglée. Réglez la poignée.

La cartouche thermostatique est

défectueuse.

Remplacez la cartouche

thermostatique

La température est irrégulière. La cartouche thermostatique est

défectueuse.

Remplacez la cartouche

thermostatique.

La pression d’eau est faible. Les filtres de la cartouche

thermostatique sont obturés

Nettoyez les filtres.

L’eau est soit chaude, soit froide,

mais il est impossible d’obtenir de

l’eau tiède.

Ce problème n’est pas dû à

une défectuosité du produit

– les conduites d’alimentation

d’eau chaude et d’eau froide sont

inversées.

Modifiez les raccordements.

1 cartridge 88586000

2 retainer plate 88519000

3 sleeve 88520XX0

4 carrier plate 88518000

5 Duotec spacers* 88529000

6 Duotec strips 96234000

7 carrier plate screw 88652000

8 cross handle 88608XX0

9 lever handle 88610XX0

10 scroll handle 88609XX0

11 Solaris² handle 88530XX0

12 Stratos handle 88547XX0

13 Metro handle 88548XX0

14 Interaktiv S/Talis S 88641XX0

15 Metris handle

16 Focus S handle

17 oval escutcheon 88531XX0

18 round escutcheon 88521XX0

19 Retroaktiv escutcheon

20 thermostat cartridge 94282000

21 Allegro² handle

22 Metro² handle

XX0 = color code

000 = chrome

620 = oil rub bronze

820 = brushed nickel

830 = polished nickel

930 = polished brass

*included with oval escutcheon only

Replacement Parts

Cleaning Recommendation for Hansgrohe Products

Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of

the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain

criteria when cleaning.

Cleaning Materials for Faucets and Showers

Acids are a necessary ingredient of cleaning materials for removing lime, however please pay attention to the follow-

ing points when cleaning faucets and showers:

Only use cleaning materials which are explicitly intended for this type of application.

Never use cleaning materials which contain hydrochloric, formic, phosphoric, or acetic acid, as they cause

considerable damage.

Never mix one cleaning material with another.

Never use cleaning materials or appliances with an abrasive effect, such as unsuitable cleaning powders, sponge

pads, or micro fiber cloths.

Cleaning Instructions for Faucets and Showers

Please follow the cleaning material manufacturer’s instructions. In addition, pay attention to the following points:

Clean the faucets and showers as and when required

Use the amount of cleaning product and the amount of time recommended by the manufacturer. Do not leave the

cleaner on the fixture longer than necessary.

Regular cleaning can prevent calcification.

When using spray cleaners, spray first onto a soft cloth or sponge. Never spray directly onto the faucet as drop-

lets can enter openings and gaps and cause damage.

After cleaning, rinse thoroughly with clean water to remove any cleaner residue.

Important

Residues of liquid soaps, shampoos, and shower foams can also cause damage, so rinse with clean water after using.

Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage.

Components with damaged surfaces must be replaced or injury could result.

Damage caused by improper treatment is not covered under the warranty.

•

Recommandations pour le nettoyage des produits Hansgrohe

Les robinetteries modernes de lavabo, de cuisine et de douche utilisent des matériaux très différents pour répondre aux

besoins du marché en termes de conception et de fonctionnalité. Certaines règles de base doivent être respectées lors Certaines règles de base doivent être respectées lorsCertaines règles de base doivent être respectées lors

du nettoyage de ces produits afin d’éviter de les endommager ou d’avoir à les retourner.

Produits de nettoyage pour robinetteries et douches

Les acides sont une partie intégrante nécessaire de tous les produits de détartrage; il faut cependant prendre les

précautions suivantes lors du nettoyage des robinets et des douches :

N’utilisez que des produits/articles de nettoyage conçus spécifiquement pour les articles de robinetterie et de

douche.

N’utilisez jamais de produits/articles de nettoyage contenant de l’acide chlorhydrique, formique, phosphorique

ou acétique car ils pourraient causer des dommages considérables.

Ne mélangez jamais deux produits de nettoyage.

N’utilisez jamais de produits/articles de nettoyage de nature abrasive tels que poudres de nettoyage, tampons-

éponge ou chiffons microfibre non appropriés.

•

Limited Lifetime Consumer Warranty

This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”).

This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1,

1996, and installed in either the United States or Canada.

WHO IS COVERED BY THE WARRANTY

This warranty extends to the original consumer purchaser only. This warranty is non-transferable.

WHAT IS COVERED BY THE WARRANTY

This warranty covers only your Hansgrohe manufactured product. Hansgrohe warrants this product against defects in

material or workmanship as follows: Hansgrohe will repair at no charge for parts only or, at its option, replace any

product or part of the product that proves defective because of improper workmanship and/or material, under normal

installation, use, service and maintenance. If Hansgrohe is unable to provide a replacement and repair is not practical

or cannot be timely made, Hansgrohe may elect to refund the purchase price in exchange for the return of the product.

LENGTH OF WARRANTY

Replacement or repaired parts of products will be covered for the term of this warranty as stated in the following two

sentences. If you are a consumer who purchased the product for use primarily for personal, family, or household

purposes, this warranty extends for as long as you own the product and the home in which the product is originally

installed. If you purchased the product for use primarily for any other purpose, including, without limitation, a commer-

cial purpose, this warranty extends only (i) for 1 year, with respect to Hansgrohe and Commercial products, and (ii) for

5 years, with respect to AXOR products.

THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR:

A. Conditions, malfunctions or damage not resulting from defects in material or workmanship.

B. Conditions, malfunctions or damage resulting from (1) normal wear and tear, improper installation, improper

maintenance, misuse, abuse, negligence, accident or alteration, or (2) the use of abrasive or caustic cleaning

agents or “no-rinse” cleaning products, or the use of the product in any manner contrary to the product instruc-

tions. (3) Conditions in the home such as excessive water pressure or corrosion.

C. Labor or other expenses for the disconnection, deinstallation, or return of the product for warranty service, or for

installation or reinstallation of the product (including but not limited to proper packaging and shipping costs), or

Instructions de nettoyage pour robinetteries et douches

Veuillez suivre les instructions du fabricant de produits/articles de nettoyage. De plus, tenez compte des conseils De plus, tenez compte des conseilsDe plus, tenez compte des conseils

suivants :

Nettoyez vos produits de robinetterie et de douche aussi souvent que nécessaire.

Utilisez la quantité de produit nettoyant et respectez la durée recommandée par le fabricant. Ne laissez pas le Ne laissez pas leNe laissez pas le

produit sur les articles de robinetterie plus longtemps que nécessaire.

Un nettoyage régulier peut prévenir la formation de dépôts calcaires.

Si vous utilisez des nettoyants en vaporisateur, vaporisez d’abord sur une éponge ou un chiffon. Ne vaporisez Ne vaporisezNe vaporisez

jamais directement sur un robinet : des gouttelettes pourraient s’infiltrer dans les ouvertures et les interstices et

endommager celui-ci.

Après le nettoyage, rincez abondamment avec de l’eau propre pour éliminer tout résidu de produit nettoyant.

Important

Les résidus de savon liquide, de shampoing et de mousse pour la douche peuvent également endommager la robinette-

rie; rincez donc avec de l’eau propre après utilisation de ces produits.

Veuillez noter : si la surface est déjà endommagée, les produits de nettoyage l’endommageront encore plus.si la surface est déjà endommagée, les produits de nettoyage l’endommageront encore plus.

Les composants dont la surface est endommagée devraient �tre remplacés sous peine d’entraîner

des blessures.

Les dommages dus à un mauvais traitement ne sont pas couverts par la garantie.

•

Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004

Tel. 770-360-9880 • Fax 770-360-9887

www.hansgrohe-usa.com

US - Installation Instructions • Part No. 90965001-06 • Revised 04/2008

for installation or reinstallation of the product.

D. Accessories, connected materials and products, or related products not manufactured by Hansgrohe.

TO OBTAIN WARRANTY PARTS OR INFORMATION

Contact your Hansgrohe retailer, or contact Technical Service at:

Hansgrohe Inc.

1492 Bluegrass Lakes Parkway

Alpharetta GA 30004

Toll-free (800) 334-0455.

In requesting warranty service, you will need to provide

1. The sales receipt or other evidence of the date and place of purchase.

2. A description of the problem.

3. Delivery of the product or the defective part, postage prepaid and carefully packed and insured, to Hansgrohe

Inc. 1492 Bluegrass Lakes Parkway, Alpharetta, Georgia 30004, Attention: Technical Service, if required by

Hansgrohe.

When warranty service is completed, any repaired or replacement product or part will be returned to you postage

prepaid.

EXCLUSIONS AND LIMITATIONS

REPAIR OR REPLACEMENT (OR, IN LIMITED CIRCUMSTANCES, REFUND OF THE PURCHASE PRICE) AS PROVIDED

UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. HANSGROHE NEITHER ASSUMES

NOR AUTHORIZES ANY PERSON TO CREATE FOR IT ANY OBLIGATION OR LIABILITY IN CONNECTION WITH

THIS PRODUCT.

HANSGROHE SHALL NOT BE LIABLE TO PURCHASER OR ANY PERSON FOR ANY INCIDENTAL, SPECIAL, OR

CONSEQUENTIAL DAMAGES, ARISING OUT OF BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY

(INCLUDING MERCHANTABILITY).

Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation

or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights which

vary from State to State. You may be required by law to give us a reasonable opportunity to correct or cure any failure

to comply before you can bring any action in court against us under the Magnuson-Moss Warranty Act.

PRODUCT INSTRUCTIONS AND QUESTIONS

Upon purchase or prior to installation, please carefully inspect your Hansgrohe product for any damage or visible

defect. Prior to installing, always carefully study the enclosed instructions on the proper installation and the care and

maintenance of the product. If you have questions at any time about the use, installation, or performance of your

Hansgrohe product, or this warranty, please call or write to us or call us toll-free at 800 334 0455.

Axor 06064XX0 User manual

Brand: Axor

Model: 06064XX0

Category: Sanitary ware

Type: User manual

Download PDF

report

in other languages

français: Axor 06064XX0 Manuel utilisateur

Axor 06064XX0 User manual

Axor 06064XX0 User manual

in other languages

Related papers

Other documents