Brother 888-X53 User manual

Operation Manual

Product Code: 888-X53/X54/X55/X56

Sewing Machine

Please visit us at http://solutions.brother.com where you can get product

support and answers to frequently asked questions (FAQs).

———————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—————

1

IMPORTANT SAFETY

INSTRUCTIONS

Please read these safety instructions

before attempting to use the machine.

DANGER - To reduce

the risk of electric shock:

1 Always unplug the machine from

the electrical outlet immediately after

using, when cleaning, when making

any user servicing adjustments

mentioned in this manual, or if you are

leaving the machine unattended.

WARNING - To

reduce the risk of burns, fire, electric

shock, or injury to persons.

2 Always unplug the machine from

the electrical outlet when making any

adjustments mentioned in the

instruction manual:

• To unplug the machine, switch the

machine to the symbol “O” position

to turn it off, then grasp the plug and

pull it out of the electrical outlet. Do

not pull on the cord.

• Plug the machine directly into the

electrical outlet. Do not use an

extension cord.

• Always unplug your machine if the

power is cut.

3 Never operate this machine if it has

a damaged cord or plug, if it is not

working properly, if it has been

dropped or damaged, or water is spilled

on the unit. Return the machine to the

nearest authorized dealer or service

center for examination, repair,

electrical or mechanical adjustment.

• While the machine is stored or in use

if you notice anything unusual, such

as an odor, heat, discoloration or

deformation, stop using the machine

and immediately unplug the power

cord.

• When transporting the machine, be

sure to carry it by its handle. Lifting

the machine by any other part may

damage the machine or result in the

machine falling, which could cause

injuries.

• When lifting the machine, be careful

not to make any sudden or careless

movements, otherwise you may

injure your back or knees.

4 Always keep your work area clear:

• Never operate the machine with any

air openings blocked. Keep

ventilation openings of the machine

and foot control free from the build

up of lint, dust, and loose cloth.

• Do not store objects on the foot

controller.

• Do not use extension cords. Plug the

machine directly into the electrical

outlet.

• Never drop or insert any object into

any opening.

• Do not operate where aerosol (spray)

products are being used or where

oxygen is being administered.

• Do not use the machine near a heat

source, such as a stove or iron;

otherwise, the machine, power cord

or garment being sewn may ignite,

resulting in fire or an electric shock.

• Do not place this machine on an

unstable surface, such as an unsteady

or slanted table, otherwise the

machine may fall, resulting in

injuries.

5 Special care is required when

sewing:

• Always pay close attention to the

needle. Do not use bent or damaged

needles.

2

——————

———————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

• Keep fingers away from all moving

parts. Special care is required around

the machine needle.

• Do not turn on the machine while

pressing down the foot controller.

The machine may start unexpectedly

and cause personal injury or damage

to the machine.

• Switch the machine to the symbol “O”

position to turn it off when making any

adjustments in the needle area.

• Do not use a damaged or incorrect

needle plate, as it could cause the

needle to break.

• Do not push or pull the fabric when

sewing, and follow careful instruction

when freehand stitching so that you

do not deflect the needle and cause it

to break.

6 This machine is not a toy:

• Your close attention is necessary when

the machine is used by or near children.

• The plastic bag that this machine was

supplied in should be kept out of the

reach of children or disposed of.

Never allow children to play with the

bag due to the danger of suffocation.

• Do not use outdoors.

7 For a longer service life:

• When storing this machine, avoid

direct sunlight and high humidity

locations. Do not use or store the

machine near a space heater, iron,

halogen lamp, or other hot objects.

• Use only neutral soaps or detergents

to clean the case. Benzene, thinner,

and scouring powders can damage

the case and machine, and should

never be used.

• Always consult the operation manual

when replacing or installing any

assemblies, the presser feet, needle, or

other parts to assure correct installation.

8 For repair or adjustment:

• If the Light unit (light-emitting diode)

is damaged, it must be replaced by

authorized dealer.

• In the event a malfunction occurs or

adjustment is required, first follow the

troubleshooting table in the back of

the operation manual to inspect and

adjust the machine yourself. If the

problem persists, please consult your

local authorized Brother dealer.

Use this machine only for its intended

use as described in this manual.

Use accessories recommended by the

manufacturer as contained in this manual.

The contents of this manual and

specifications of this product are

subject to change without notice.

For additional product information,

visit our web site at www.brother.com

SAVE THESE

INSTRUCTIONS

This machine is intended

for household use.

This appliance is not intended for use

by persons (including children) with

reduced physical, sensory or mental

capabilities, or lack of experience and

knowledge, unless they have been

given supervision or instruction

concerning use of the appliance by a

person responsible for their safety.

Children should be supervised to

ensure that they do not play with the

appliance.

This appliance can be used by

children aged from 8 years and

above and persons with reduced

physical, sensory or mental

capabilities or lack of

experience and knowledge if

they have been given

supervision or instruction

concerning use of the appliance

in a safe way and understand

the hazards involved. Children

shall not play with the

appliance. Cleaning and user

maintenance shall not be made

by children without supervision.

———————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—————

3

FOR USERS IN THE UK, EIRE,

MALTA AND CYPRUS ONLY

IMPORTANT

• In the event of replacing the plug fuse, use a fuse

approved by ASTA to BS 1362, i.e. carrying the

mark, rating as marked on plug.

• Always replace the fuse cover. Never use plugs with

the fuse cover omitted.

• If the available electrical outlet is not suitable for the

plug supplied with this equipment, you should contact

your authorized dealer to obtain the correct lead.

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS ...........1

1. KNOWING YOUR SEWING

MACHINE .................................. 4

ACCESSORIES .................................................4

Optional accessories .......................................... 4

THE MAIN PARTS ...........................................5

Flat bed attachment ............................................ 5

USING YOUR SEWING MACHINE ................6

Connecting plugs ............................................... 6

Main power and sewing light switch .................. 7

Foot controller .................................................... 7

Checking the needle ........................................... 7

Replacing the needle .......................................... 7

Changing the presser foot ................................... 8

THE CONTROLS ............................................. 9

Pattern selection dial .......................................... 9

Patterns and stitch names ................................... 9

Reverse sewing lever ........................................ 10

THREADING THE MACHINE .......................11

Winding the bobbin ......................................... 11

Lower threading ............................................... 13

Upper threading ............................................... 14

Drawing up the lower thread ............................ 16

FABRIC, THREAD, AND NEEDLE

COMBINATIONS ......................................... 17

2. SEWING BASICS ...................... 18

Please read before sewing ................................ 18

Starting sewing ................................................. 18

Trial sewing ...................................................... 19

Changing the sewing direction ......................... 19

Sewing thick fabrics ......................................... 19

Sewing thin fabrics ........................................... 20

Sewing stretch fabrics ....................................... 20

Stitching cylindrical pieces ............................... 20

Thread tension ................................................. 20

3. BUILT-IN STITCHES ................. 22

Straight stitching ...............................................22

Zigzag stitching .................................................22

Blind hem stitching ...........................................23

Overedge stitching ............................................24

Elastic stitching .................................................24

Double action stitching .....................................25

4. SEWING BUTTONHOLES AND

BUTTONS ............................... 26

Making a buttonhole .........................................26

Adjusting buttonholes .......................................27

5. USING ATTACHMENTS AND

APPLICATIONS ....................... 28

Zipper insertion ................................................28

Gathering ..........................................................29

Appliqués .........................................................29

USING OPTIONAL ACCESSORIES ............... 30

Sewing buttons .................................................30

Darning ............................................................31

Using the blind stitch foot ................................. 32

6. APPENDIX ................................ 33

MAINTENANCE ........................................... 33

Restrictions on oiling ........................................33

Precautions on storing the machine ..................33

Cleaning ...........................................................33

TROUBLESHOOTING .................................. 35

INDEX .......................................................... 38

4

——————

—————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

1

1 KNOWING YOUR SEWING MACHINE

ACCESSORIES

We have designed these accessories to help you easily perform most sewing tasks.

Note

● The included accessories vary depending on the machine model.

Optional accessories

The following are available as optional accessories to be purchased separately. Depending on the model you

purchased, the following accessory may be included with your machine.

1. 2. 3. 4. 5.

6. 7.

No. Part Name

Part Code

Americas Others

1

Zigzag foot “J”

(on machine)

XC4901-121

2 Buttonhole foot “A” X59369-321

3 Zipper foot “I” XE9369-001

4

Bobbin

(One is on machine)

SA156

SFB:

XA5539-151

5

Needle set

(90/14 needle)

3-piece set: XE5328-001

2-piece set: XE7064-001

6 Screwdriver XF3557-001

7 Foot controller See page 5

No. Part Name

Part Code

Americas Others

1. 2. 3. 4. 5.

6. 7. 8.

No. Part Name

Part Code

Americas Others

1 Darning Plate XC6063-021

2 Button sewing foot “M” XE2137-001

3 Walking Foot SA107

F034N:

XC2165-002

4 Quilting Foot SA129

F005N:

XC1948-052

5 1/4-inch Quilting Foot SA125

F001N:

XC1944-052

6 Narrow Hemmer Foot SA127

F003N:

XC1945-052

7 Blind Stitch Foot SA134

F018N:

XC1976-052

8 Quilting guide SA132

F016N:

XC2215-052

No. Part Name

Part Code

Americas Others

KNOWING YOUR SEWING MACHINE ————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————

—————

5

THE MAIN PARTS

1 Bobbin winder (Page 11)

This winds the thread onto the bobbin for use as the

lower thread.

2 Spool pin (Page 11, 14)

This holds the spool of thread.

3 Thread guide (Page 11, 14)

This is used when winding the thread onto the

bobbin and then threading the machine.

4 Thread take-up lever (Page 15)

5 Upper tension-control dial (Page 21)

This controls the tension of the upper thread.

6 Thread cutter (Page 19)

Pass the threads through the thread cutter to cut

them.

7 Flat bed attachment with accessory compartment

(Page 5)

8 Presser foot (Page 8)

9 Reverse sewing lever (Page 10)

Push this lever to stitch in the reverse direction.

0 Buttonhole fine-adjustment screw (Page 27)

A Pattern selection dial (Page 9)

Rotate the dial in either direction to choose the

stitch you want.

B Handwheel

Used to manually raise and lower the needle.

C Main power and sewing light switch (Page 7)

You can turn the main power and sewing light

switch on and off.

D Foot controller jack / socket (Page 6)

Plug in the foot controller plug and connect the

machine to the power supply.

E Presser foot lever (Page 14)

Used to raise and lower the presser foot.

F Foot controller (Page 7)

You can use this to control the sewing speed, and to

start and stop sewing.

Foot Controller:

Model KD-1902 for 110-120V area

KD-1902 for 110-127V area (Brazil only)

Model KD-2902 for 220-240V area

The foot controller part code differs depending on the

country or region. Contact your dealer or the nearest

authorized service center.

Flat bed attachment

The accessories can be stored in a compartment inside

the flat bed attachment.

1

Slide the flat bed attachment to the left to

open it.

1 Flat bed attachment

2 Storage compartment

1

2

3

4

6

7

8

5

0

9

D

C

F

A

E

B

1

2

6

——————

—————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

1

USING YOUR SEWING MACHINE

WARNING

CAUTION

Connecting plugs

1

Connect the foot controller plug to the

machine.

2

Connect the power supply plug to a wall

outlet.

Note

● If a power outage occurs while the sewing

machine is being operated, turn off the main

power and unplug the power supply cord.

When restarting the sewing machine, follow

the necessary procedure to correctly operate

the machine.

(For U.S.A. only)

● This appliance has a polarized plug (one

blade wider than the other). To reduce the

risk of electric shock, this plug is intended to

fit in a polarized outlet only one way. If the

plug does not fit fully in the outlet, reverse

the plug.

If it still does not fit, contact a qualified

electrician to install the proper outlet. Do

not modify the plug in any way.

● Use only regular household electricity for the power source. Using other power sources may

result in fire, electric shock, or damage to the machine.

● Make sure that the plugs on the power cord are firmly inserted into the electrical outlet and

the power supply jack on the machine.

● Do not insert the plug on the power cord into an electrical outlet that is in poor condition.

● Turn off the main power and remove the plug in the following circumstances:

• When you are away from the machine

• After using the machine

• When the power fails during use

• When the machine does not operate correctly due to a bad connection or a disconnection

• During electrical storms

● Use only the power cord included with this machine.

● Do not use extension cords or multi-plug adapters with many other appliances plugged in to

them. Fire or electric shock may result.

● Do not touch the plug with wet hands. Electric shock may result.

●

When unplugging the machine, always turn off the main power first. Always grasp the plug to

remove it from the outlet. Pulling on the cord may damage the cord, or lead to fire or electric shock.

● Do not allow the power cord to be cut, damaged, modified, forcefully bent, pulled, twisted,

or bundled. Do not place heavy objects on the cord. Do not subject the cord to heat. These

things may damage the cord and cause fire or electric shock. If the cord or plug is damaged,

take the machine to your authorized dealer for repairs before continuing use.

● Unplug the power cord if the machine is not to be used for a long period of time. Otherwise

a fire may result.

KNOWING YOUR SEWING MACHINE ————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————

—————

7

Main power and sewing

light switch

This switch turns the main power and sewing light on or

off.

1 Turn on (toward the ‘I’ mark)

2 Turn off (toward the ‘O’ mark)

CAUTION

Foot controller

When you press the foot controller down lightly, the

machine will run at a low speed. When you press harder,

the machine’s speed will increase. When you take your

foot off the foot controller, the machine will stop.

1 Slower

2 Faster

You should make sure that nothing is placed on the foot

controller when the machine is not in use.

CAUTION

Note

(For U.S.A. only)

● Foot Controller: Model KD-1902

This foot controller can be used on the

machine with product code 888-X53/X54/

X55/X56.

The product code is mentioned on the

machine rating plate.

Checking the needle

The sewing needle must always be straight and sharp

for smooth sewing.

■ Checking the needle correctly

Put the flat side of the needle on a flat surface.

Check the needle from the top and the sides.

Dispose of any bent needles safely.

1 Parallel space

2 Level surface (bobbin cover, glass, etc.)

Replacing the needle

CAUTION

1

Turn off the machine.

2

Raise the needle by turning the

handwheel toward you

(counterclockwise) so that the mark on

the wheel points up.

3

Lower the presser foot lever.

1 Presser foot lever

●

Do not turn on the machine while pressing

down the foot controller. The machine

may start unexpectedly and cause

personal injury or damage to the machine.

● Do not allow pieces of cloth and dust to

build up on the foot controller. Doing so

could cause a fire or an electric shock.

2

1

2

● Always turn off the machine before you

change the needle. Otherwise, injuries

may occur if the foot controller is

accidentally pressed and the machine

starts sewing.

● Only use sewing machine needles for

home use. Other needles may bend or

break and cause injury.

● Never sew with a bent needle. A bent

needle will easily break and cause injury.

1

2

1

8

——————

—————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

1

CAUTION

4

Hold the needle with your left hand, and

then use a screwdriver to turn the needle

clamp screw counterclockwise to remove

the needle.

1 Use a screwdriver

• Do not use excessive force when loosening

or tightening the needle clamp screw,

otherwise certain parts of the sewing

machine may be damaged.

5

With the flat side of the needle toward the

back of the machine, insert the needle

until it touches the needle stopper. Next,

tighten the needle clamp using a

screwdriver.

CAUTION

Changing the presser foot

CAUTION

You will have to change the presser foot depending on

what you want to sew and how.

1

Turn off the machine.

Raise the presser foot lever.

2

Raise the needle by turning the

handwheel toward you

(counterclockwise) so that the mark on

the wheel points up.

3

Remove the presser foot by pulling it

vertically downward.

4

Put a different presser foot on the needle

plate so that the bar on the presser foot is

in line with the slot on the shank.

● Before replacing the needle, place fabric

or paper under the presser foot to

prevent the needle from falling into the

hole in the needle plate.

1 Use a screwdriver

2 Needle stopper

3 Needle

1

2

3

1

● Make sure you insert the needle until it

touches the stopper, and securely tighten

the needle clamp screw with a

screwdriver, otherwise the needle may

break or the machine may be damaged.

● Always turn off the machine before you

change the presser foot. If you leave the

power on and step on the controller, the

machine will start and you may be

injured.

● Always use the correct presser foot for

the stitch pattern you have chosen. If

you use the wrong presser foot, the

needle may strike the presser foot and

bend or break, and may cause injury.

● Only use presser feet that have been

designed to be used with this machine.

Using any other presser foot may cause

accident or injury.

1 Presser foot holder

2 Presser foot

1

2

KNOWING YOUR SEWING MACHINE ————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————

—————

9

5

Lower the presser foot lever and fix the

presser foot onto the shank. If the presser

foot is in the correct place, the bar should

snap in.

1 Shank

2 Bar

■ Presser foot installation orientation

CAUTION

THE CONTROLS

Pattern selection dial

CAUTION

To choose a stitch, simply turn the pattern selection dial

in either direction.

1 Pattern selection dial

2 Chosen pattern number

Patterns and stitch names

*1 : Stitch nos. 15-17 are only available on certain

models.

1

2

● If the presser foot is not installed with

the correct orientation, the needle may

strike the presser foot, which may bend

or break the needle and cause injury.

● When you use the pattern selection dial

to choose a pattern, raise the needle by

turning the handwheel toward you

(counterclockwise) so that the mark on

the wheel points up. If the needle is in

the down position when you turn the

pattern selection dial, the needle, presser

foot or fabric may be damaged.

1

2

11

Pattern

Preset Length

(mm (inch))

Reference

Page

Stitch Name

Preset Width

(mm (inch))

0.5 (1/32)

26

4-STEP AUTOMATIC

BUTTONHOLE

5 (3/16)

0.7 (1/32)

22, 29, 30,

32

ZIGZAG STITCH 1.8 (1/8)

1.5 (1/16)

22, 29, 30,

32

ZIGZAG STITCH 3.3 (3/16)

1

2

3

4

5

6 7

8

9

10

11

12

13

14

15

16 17

1

2

3

*1

10

——————

—————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

1

Reverse sewing lever

You can use reverse sewing for back tacking and

reinforcing seams.

To sew in reverse, push the reverse sewing lever in as

far as possible and hold it in that position while you

lightly push the foot controller. To sew forward, release

the reverse sewing lever. The machine will then sew

forward.

The length of reverse stitches is fixed at 2 mm

(1/16 inch).

1 Reverse sewing lever

2 (1/16)

22, 29, 30,

32

ZIGZAG STITCH 5 (3/16)

0.5 (1/32)

22, 29

ZIGZAG (SATIN)

STITCH

5 (3/16)

1.6 (1/16)

22, 31

STRAIGHT STITCH

(Center Needle

Position)

—

1.8 (1/8)

22, 31

STRAIGHT STITCH

(Center Needle

Position)

—

2 (1/16)

22, 31

STRAIGHT STITCH

(Center Needle

Position)

—

3 (1/8)

22, 28, 29,

31, 32

STRAIGHT STITCH

(Center Needle

Position)

—

4 (3/16)

22, 31

STRAIGHT STITCH

(Center Needle

Position)

—

2.5 (3/32)

22, 29, 31

STRAIGHT STITCH

(Left Needle Position)

—

2 (1/16)

23, 32

BLIND HEM STITCH 5 (3/16)

1 (1/16)

24

ELASTIC STITCH 5 (3/16)

Pattern

Preset Length

(mm (inch))

Reference

Page

Stitch Name

Preset Width

(mm (inch))

4

5

6

7

8

9

10

11

12

13

2 (1/16)

23, 32

STRETCH BLIND

HEM STITCH

5 (3/16)

2 (1/16)

24

OVEREDGE STITCH 5 (3/16)

1.2 (1/16)

25

DOUBLE ACTION

STITCH

5 (3/16)

1.2 (1/16)

25

BRIDGING STITCH 5 (3/16)

Pattern

Preset Length

(mm (inch))

Reference

Page

Stitch Name

Preset Width

(mm (inch))

14

15

16

17

1

KNOWING YOUR SEWING MACHINE ————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————

—————

11

THREADING THE MACHINE

Winding the bobbin

CAUTION

1

Pull up the spool pin and put a spool of

thread on this pin.

2

While holding the thread from the spool

with your right hand, pass the thread

toward you, in the groove on the thread

guide. Then, pass the thread around the

pre-tension disk and pull the thread in

completely.

CAUTION

● We designed the bobbin that comes with this machine. If you use bobbins from other models,

the machine will not work properly. Only use the bobbin that comes with this machine or

bobbins of the same type (part code: SA156, SFB: XA5539-151). Using other bobbins may

cause damage to the machine.

Actual size

11.5 mm

(7/16 inch)

This model Other models

1 Pre-tension disk 2 Bobbin winder shaft 3 Bobbin

3

2

1

1 Pull the thread

in completely.

● If the spool of thread is in the wrong

place, or is set incorrectly, the thread

may tangle on the spool pin.

12

——————

—————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

1

3

Pass the end of the thread through the hole

on the bobbin from the inside of the bobbin.

4

Put the bobbin onto the bobbin winder

shaft and slide the bobbin winder shaft to

the right. Turn the bobbin clockwise, by

hand, until the projection slides into the

notch of the bobbin.

• Make sure to pull out 7 to 10 cm (3-4 inches)

of thread from the hole on the bobbin.

1 Projection

2 Notch

3 7-10 cm (3 – 4 inches)

CAUTION

5

Turn on the machine.

CAUTION

6

While holding the end of the thread,

gently press the foot controller to wind

the thread around the bobbin a few times.

Then stop the machine.

7

Trim the excess thread above the bobbin.

• Leave 1 cm (1/2 inch) of thread from the hole

on the bobbin.

1 1 cm (1/2 inch)

CAUTION

8

Press the foot controller to start.

9

When the bobbin seems full and begins

spinning slowly, take your foot off the foot

controller.

0

Cut the thread, slide the bobbin winder

shaft to the left and remove the bobbin.

Note

●

When the sewing machine is started or the

handwheel is turned after winding the thread

around the bobbin, the machine will make a

clicking sound; this is not a malfunction.

● The needle bar does not move when you

slide the bobbin winder shaft to the right.

CAUTION

● Pull the thread taut and hold the end of

the thread straight up. If the thread is too

short, not pulled taut or held at an angle,

injuries may occur when the thread is

wound around the bobbin.

●

Do not turn on the machine while pressing

down the foot controller. The machine

may start unexpectedly and cause

personal injury or damage to the machine.

3

1

2

●

Make sure you follow the instructions

carefully. If you do not cut the excess thread

completely before winding the bobbin, when

the thread runs low it may tangle around the

bobbin and cause the needle to break.

● Not winding the bobbin properly may

cause the thread tension to loosen, and

may break the needle.

1 Wound evenly

2 Wound poorly

1

2

KNOWING YOUR SEWING MACHINE ————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————

—————

13

Lower threading

Install the bobbin wound with thread.

CAUTION

1

Prepare the bobbin wound properly

before threading the lower thread.

• See page 11 for the details about bobbin

winding.

2

Raise the needle by turning the

handwheel toward you

(counterclockwise) and raise the presser

foot lever.

3

Remove the bobbin cover by sliding it and

lift toward you.

1 Bobbin cover

4

Put the bobbin in so the thread comes out

in the direction shown by the arrow.

CAUTION

5

Hold the end of the thread, push the

bobbin down with your finger, and then

pass the thread through the slit, as shown.

• If the thread is not correctly inserted through

the tension-adjusting spring of the bobbin

case, it may cause incorrect thread tension.

1 Tension-adjusting spring

6

Replace the bobbin cover. Put the

projection into the race retainer groove

and push closed.

1 Groove

2 Projection

• Make sure that the end of the thread comes

out from the cover toward the rear of the

machine (as shown in the illustration).

• Draw up the lower thread before starting

sewing. Refer to “Drawing up the lower

thread” on page 16 after threading the upper

thread.

●

Make sure you turn off the machine

while threading. If you accidentally step

on the foot controller and the machine

starts to sew, you could be injured.

● Make sure you set the bobbin so the

thread unrolls in the right direction. If

the thread unrolls in the wrong

direction, it may cause the thread

tension to be incorrect or break the

needle.

1

2

14

——————

—————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

1

Upper threading

1 Spool pin

2 Thread guide (back)

3 Thread guide (front)

4 Thread take-up lever

5 Mark on the handwheel

CAUTION

1

Turn off the machine.

2

Raise the presser foot lever.

1 Presser foot lever

3

Raise the needle by turning the

handwheel toward you

(counterclockwise) so that the mark on

the wheel points up.

• If the needle is not correctly raised, the

sewing machine can not be threaded.

1 Mark on the wheel

4

Pull up the spool pin and put a spool of

thread on this pin.

CAUTION

4

3

2

1

5

● When threading the upper thread, carefully follow the instructions. If the upper threading is

not correct, the thread may become tangled or the needle may bend or break.

● Never use a thread weight of 20 or lower.

● Use the needle and the thread in the correct combination. For details on the correct

combination of needles and threads, refer to “FABRIC, THREAD, AND NEEDLE

COMBINATIONS” on page 17.

1

● If the spool of thread is in the wrong

place, or is set incorrectly, the thread

may tangle on the spool pin and cause

the needle to break.

KNOWING YOUR SEWING MACHINE ————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————

—————

15

5

While holding the thread from the spool

with your right hand, pass the thread

toward you, in the groove on the thread

guide.

• Make sure that the spring in the groove

catches the thread.

1 Spring

6

Feed the upper thread as shown in the

following illustration.

7

Make sure you guide the thread through

the thread take-up lever from right to left

as shown in the following illustration.

1 Thread take-up lever

Memo

● If the thread take-up lever is lowered, the

upper thread can not be wrapped around

the thread take-up lever. Make sure you

raise the needle by turning the handwheel

toward you (counterclockwise) so that the

mark on the wheel points up.

8

Put the thread behind the guide above the

needle.

• The thread can easily be passed behind the

needle bar thread guide by holding the

thread in your left hand, then feeding the

thread with your right hand.

1 Needle bar thread guide

9

Thread the needle from front to back

leaving a thread tail of about 5 cm

(2 inches).

1 5 cm (2 inches)

Note

● Make sure you raise the presser foot lever

and the thread take-up lever before you feed

the upper thread.

● If you incorrectly feed the thread you may

cause sewing problems.

1

2

3

4

5

1

16

——————

—————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

1

Drawing up the lower

thread

1

While lightly holding the end of the upper

thread, slowly turn the handwheel toward

you (counterclockwise) by hand to lower

and then raise the needle.

2

Pull on the upper thread to draw up the

lower thread.

1 Upper thread

2 Lower thread

3

Pull out about 10 cm (4 inches) of both

threads and put them toward the back of

the machine under the presser foot.

1 Upper thread

2 Lower thread

1

2

1

2

KNOWING YOUR SEWING MACHINE ————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————

—————

17

FABRIC, THREAD, AND NEEDLE COMBINATIONS

Note

● Never use a thread weighted #20 or lower. It may cause machine malfunction.

Memo

● The lower the thread number, the thicker the thread; and the higher the needle number, the thicker the

needle.

■ Ball point needle

Use the ball point needle when sewing on stretch fabrics or fabrics where skipped stitches easily occur.

The factory recommended needle is “HG-4BR” (Organ). Schmetz needles “JERSEY BALL POINT” 130/705H SUK

90/14 may be used as a substitute.

■ Transparent nylon thread

Use a 90/14 to 100/16 needle, regardless of the fabric or thread.

CAUTION

Fabric Type/Application

Thread

Size of Needle

Type Size

Medium weight

fabrics

Broadcloth Cotton thread

60–90

75/11–90/14

Taffeta Synthetic thread

Flannel, Gabardine Silk thread 50

Thin fabrics

Lawn Cotton thread

60–90

65/9–75/11

Georgette Synthetic thread

Challis, Satin Silk thread 50

Thick fabrics

Denim Cotton thread

30 100/16

50

90/14–100/16

Corduroy Synthetic thread

50–60

Tweed Silk thread

Stretch fabrics

Jersey

Thread for knits 50–60

Ball point needle

75/11–90/14

(gold colored)

Tricot

Easily frayed fabrics

Cotton thread

50–90

65/9–90/14Synthetic thread

Silk thread 50

For top-stitching

Synthetic thread

Silk thread

30 100/16

50–60 75/11–90/14

●

Make sure you follow the needle, thread, and fabric combinations listed in the table.

Using the wrong combination, such as heavyweight fabric like denim with a small needle

(65/9-75/11), may bend or break the needle. The wrong combination may also cause the seam

to be uneven, the fabric to pucker, or the machine to skip stitches.

18

——————

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

2

2 SEWING BASICS

Please read before sewing

CAUTION

Starting sewing

1

Turn on the machine.

CAUTION

2

Raise the needle by turning the

handwheel toward you

(counterclockwise) so that the mark on

the wheel points up.

3

Turn the pattern selection dial to select a

stitch (see page 9).

4

Change the presser foot (see page 8).

5

Raise the presser foot lever.

1 Presser foot lever

6

Place the fabric under the presser foot,

pass the thread under the presser foot,

and then pull out about 5 cm (2 inches) of

thread toward the rear of the machine.

1 5 cm (2 inches)

● To avoid being injured, watch the needle carefully while you are using the machine. Keep

your hands away from moving parts.

● Do not stretch or pull the fabric during sewing, otherwise the needle may be damaged and

you may be injured.

● Do not use bent or broken needles, otherwise you may be injured.

● Take care that the needle does not hit basting pins or other objects during sewing. The needle

may break and you may be injured.

● Always use the correct presser foot. If you use the wrong presser foot, the needle may hit the

presser foot and bend or break and you may be injured.

● When you turn the handwheel by hand, always turn it toward you (counterclockwise).

Turning it the other way may cause the thread to tangle and damage the needle or fabric, and

you may be injured.

● Do not start sewing without placing the fabric under the presser foot, otherwise the presser

foot may be damaged.

●

Do not turn on the machine while pressing

down the foot controller. The machine

may start unexpectedly and cause

personal injury or damage to the machine.

1

SEWING BASICS ————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—

—————————————————————————————————————————————————————————————————————————————————————————————————

—————

19

7

While holding the end of the thread and

the fabric with your left hand, turn the

handwheel toward you

(counterclockwise) with your right hand

to lower the needle to the starting point of

the stitching.

8

Lower the presser foot lever.

1 Presser foot lever

9

Slowly press down on the foot controller.

X The machine starts sewing.

0

Take your foot off the foot controller.

X The machine stops sewing.

• You can use reverse sewing for back tacking

and reinforcing seams by pressing the reverse

sewing lever. Refer to “Reverse sewing lever”

on page 10 for the details.

a

Raise the needle by turning the

handwheel toward you

(counterclockwise).

b

Raise the presser foot lever.

c

Pull the fabric to the left side of the

machine, and then pass the threads

through the thread cutter to cut them.

.

1 Thread cutter

Trial sewing

A trial piece of fabric should be sewn. Use a piece of

fabric and thread that are the same as those used for

your project, and check the thread tension and stitch

length and width.

Changing the sewing

direction

Stop the machine with the needle in the fabric at the

point where you want to change the sewing direction,

and then raise the presser foot lever. Using the needle

as a pivot, turn the fabric, lower the presser foot lever,

and then continue sewing.

Sewing thick fabrics

■ If the fabric does not fit under the presser

foot

If the fabric does not fit easily under the presser foot,

raise the presser foot lever even higher to bring the

presser foot to its highest position.

CAUTION

1

● If fabric more than 6 mm (15/64 inch)

thick is sewn or if the fabric is pushed

with too much force, the needle may

bend or break.

Page is loading ...

Brother 888-X53 User manual

Brother 888-X53 User manual

Related papers

Other documents