Memorex mt2026D User manual

Page is loading ...

Important safety instructions-1

Identification of Controls-------4

Front ------------------------------------------------------4

Back-------------------------------------------------------5

Remote Controller -------------------------------------6

Installing batteries -------------------------------------7

Effective range of the Remote----------------------7

Installation --------------------------8

Antenna installation -----------------------------------8

Connecting video and audio equipment ---------9

Connect side AV input terminals -------------------9

Connecting rear AV input terminals----------------9

Connecting Component input-----------------------10

Connecting the AV outputs--------------------------11

Basic Operation------------------12

Turning on -----------------------------------------------12

Turning off -----------------------------------------------12

Main Menu Overview ---------------------------------13

Menu navigation ---------------------------------------13

Watching AV program---------------------------------14

Switching from AV to TV -----------------------------14

Displaying the information banner ----------------14

Using the program guide ----------------------------14

Tuning in----------------------------15

To enter the PRESET menu ------------------------15

Auto Program -------------------------------------------15

Skipping an unnecessary channel ----------------16

Checking the DTV signal strength ----------------16

Viewing channel label --------------------------------16

Channel Selection--------------- 17

Sound Control--------------------

18

Adjusting Picture-----------------19

Adjusting picture --------------------------------------19

Changing picture size -------------------------------19

Timer Setting----------------------20

To enter the CLOCK menu-------------------------20

Auto Clock Setup-------------------------------------20

Manual Clock Setup ---------------------------------20

On timer setup-----------------------------------------21

Setting Sleep timer ----------------------------------21

System Setting -------------------22

To enter the EXTRA menu -------------------------22

Selecting the OSD menu language-------------22

Selecting AUDIO language ------------------------22

Setting up Closed Caption -------------------------23

Selecting the caption type -------------------------23

Customizing digital Closed Captions------------24

Parental Control------------------25

To enter the P.LOCK menu -----------------------25

Setting up the P.LOCK password-----------------25

Enabling Parental Controls-------------------------26

Setting up MPAA ratings ---------------------------26

Setting up TV ratings--------------------------------27

Setting up Canadian English ratings ------------28

Setting up Canadian French ratings-------------28

Setting up RRT5 criteria ratings------------------29

Troubleshooting -----------------30

Specifications---------------------33

Contents

1

IMPORTANT SAFETY INSTRUCTIONS

FCC NOTICE:

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference that

may cause undesired operation.

Warning: Changes or modifications to this unit

not expressly approved by the party responsible

for compliance could void the user’s authority to

operate the equipment.

NOTE: This equipment has been tested and

found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may

cause harmful interference to radio

communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be

determined by turning the equipment off and on,

the user is encouraged to try to correct the

interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS PRODUCT TO RAIN

OR MOISTURE.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

AND ANNOYING INTERFERENCE, USE THE

RECOMMENDED ACCESSORIES ONLY.

SURGE PROTECTORS:

It is recommended to use a surge protector for AC

connection. Lightning and power surges ARE NOT covered

under warranty for this product.

ATTENTION:

POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE

LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISES ET POUSSER

JUSQU’AU FOND.

FCC WARNING:

To assure continued compliance, follow the attached

installation instructions and use only shielded cables when

connecting to other devices. Modifications not authorized by

the manufacturer may void user’s authority to operate

this device.

This Class B digital apparatus complies with Canadian

ICES-003.

Cet appareil numérique de la classe B est conforme à la

norme NMB-003 du Canada.

This TV is capable of receiving unscrambled digital

programming for both cable and external UHF/VHF

antenna (ATSC) and also can receive NTSC (cable

and external UHF/VHF antenna) programs.

2

IMPORTANT SAFETY INSTRUCTIONS (CONTINUED)

Before using the unit, be sure to read all operating instructions carefully. Please note that these are general

precautions and may not pertain to your unit. For example, this unit may not have the capability to be connected to

an outdoor antenna.

1. READ INSTRUCTIONS

All the safety and operating instructions should be read before the product is operated.

2. RETAIN INSTRUCTIONS

The safety and operating instructions should be retained for future reference.

3. HEED WARNINGS

All warnings on the product and in the operating instructions should be adhered to.

4. FOLLOW INSTRUCTIONS

All operating and use instructions should be followed.

5. CLEANING

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry cloth

for cleaning.

6. ATTACHMENTS

Do not use attachments not recommended by the product's manufacturer as they may cause hazards.

7. WATER AND MOISTURE

Do not use this product near water–for example: near a bathtub, washbowl, kitchen sink or laundry tub;

in a wet basement; or near a swimming pool.

8. ACCESSORIES

Do not place this product on an unstable cart, stand, tripod, bracket or table. The product may fall, causing

serious injury and serious damage to the product. Use only with a cart, stand, tripod, bracket or table

recommended by the manufacturer or sold with the product. Any mounting of the product should follow the

manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

8A. An appliance and cart combination should be moved with care. Quick stops, excessive force and

uneven surfaces may cause the appliance and cart combination to overturn.

9. VENTILATION

Slots and openings in the cabinet and in the back or bottom are provided for ventilation, to ensure reliable operation of

the product and to protect it from overheating. These openings must not be blocked or covered. The openings should

never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should never be

placed near or over a radiator or heat source. This product should not be placed in a built-in installation such as a

bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.

10. POWER SOURCES

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of

the type of power supply to your home, consult your appliance dealer or local power company. For products intended to

operate from battery power, or other sources, refer to the operating instructions.

11. GROUNDING OR POLARIZATION

This product is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other).

This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into

the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet.

Do not defeat the safety purpose of the polarized plug.

12. POWER-CORD PROTECTION

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or

against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from

the appliance.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

(This Caution Marking and Rating Label are located at the rear enclosure of the unit.)

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning ﬂash with arrowhead symbol

within an equilateral triangle is intended to alert

the user to the presence of uninsulated

dangerous voltage within the product’s

enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

TO PREVENT ELECTRIC SHOCK, MATCH THE WIDE BLADE OF THE PLUG TO THE WIDE SLOT AND FULLY INSERT.

3

13. LIGHTNING

To protect your product from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it

from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning

and power-line surges.

14. POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power

circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care

should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

15. OVERLOADING

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

16. OBJECT AND LIQUID ENTRY

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out

parts that could result in fire or electric shock. Never spill or spray any type of liquid on the product.

17. OUTDOOR ANTENNA GROUNDING

If an outside antenna is connected to the

product, be sure the antenna system is

grounded so as to provide some protection

against voltage surges and built-up static

charges. Section 810 of the National

Electric Code, ANSI/NFPA 70, provides

information with respect to proper

grounding of the mast and supporting

structure, grounding of the lead-in wire to

an antenna discharge product, size of

grounding conductors, location of antenna

discharge product, connection to grounding

electrodes and requirements for grounding

electrodes.

18. SERVICING

Do not attempt to service this product

yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

19. REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by the

manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in fire,

electric shock or other hazards.

20. SAFETY CHECK

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine

that the product is in proper operating condition.

21. WALL OR CEILING MOUNTING

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

22. DAMAGE REQUIRING SERVICE

Unplug the product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled or objects have fallen into the product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered

by the operating instructions, as an adjustment of other controls may result in damage and will often require extensive work

by a qualified technician to restore the product to its normal operation.

e. If the product has been dropped or the cabinet has been damaged.

f. When the product exhibits a distinct change in performance–this indicates a need for service.

23. HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves or other products

(including amplifiers) that produce heat.

24. NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding

system of the building, as close to the point of cable entry as practical.

IMPORTANT SAFETY INSTRUCTIONS (CONTINUED)

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

Identification of Controls

Front

4

4. INPUT button: Video input select.

5. MENU button: To enter into menu operation.

6. VOL- button: volume down adjust; menu item adjust.

7. VOL+ button: volume up adjust; menu item adjust.

8. CH- button: channel down select; menu item select.

9. CH+ button: channel up select; menu item select.

1. Power

button.

2. Indicator.

3. Remote sensor.

2

3

1

4

5

6

7

8

9

INPUT

MENU

VOL+

CH+CH

VOL

Back

1. COMPONENT input (Y, Cb ,Cr , AUDIO L/MONO, R)

2. RF: Antenna input.

3. AV1 input (S-VIDEO,VIDEO, AUDIO L/MONO, R)

4. AV output(VIDEO, AUDIO L, R)

5. AV2 input (VIDEO, AUDIO L/MONO, R)

5

1

2

3

4

VIDEO

L/MONO

R

(2)

5

Headphones jack

Identification of Controls (continued)

S-VIDEO

VIDEO

L/MONO

R

VIDEO

L

AUDIO

R

AUDIO

(1)

RF

Y

C

b

C

r

L/MONO

R

AUDIO

Identification of Controls(continued)

6

Remote Controller

1. POWER

Turn the unit on or off

2.INPUT

To quickly select input source

3. Direct channel selector/number buttons

Use these number buttons to select channel or input

password

4. Dash (-)

Used to enter a program number for multiple program

channels such as 2-1,2-2,etc.

5. RETURN

To quickly return to the previous viewed channel

6. CH+/-

To select channels upward or

downward

7. VOL+/-

Used to adjust volume.

8. ZOOM

To change picture size in DTV mode.

9. MUTE

Sound mute

10. CCD

To turn the CCD on or off

11. MENU

To access the Menu main page

12. DISPLAY

To display channel status or signal information

13. Menu navigation button: 5634

56: To move upward or downward in menu

operation;

34: To move left or right in menu operation;

To adjust selected menu

item in menu

operation;

14. EXIT

Used to exit the menu

15. GUIDE

To display program guide.

16. PICTURE

To select the picture mode

17. MTS/SAP

To select MONO,STEREO or SAP.

18. SLEEP

To set Sleep timer

9

10

12

2

1

7

3

6

5

14

8

16

17

11

15

13

4

18

1

2

/

Do not try to recharge batteries they are not

intended to be recharged.

/

Use only the size and type of batteries specified.

Do not mix different types of batteries together

or old batteries with fresh ones.

/

When the remote control will not be used for a

long period of time

or when the batteries are

worn out, remove the batteries.

/

Do not throw the batteries into a fire. Dispose of

used batteries in the specified manner.

/

Do not drop, dampen or disassemble the remote

control.

Notes:

/

When there is an obstacle between the TV

and the transmitter, the transmitter may not

operate.

/

When direct sunlight, and incandescent lamp,

fluorescent lamp or any other strong light

shines on the REMOTE SENSOR of the TV,

the remote operation may be unstable.

3

Installing batteries

Effective range of the Remote

7

<(Place the batteries

with their terminals

corresponding to the

(+) and (–) indications

in the battery

compartment.)

Open the battery cover.

Insert two size-AAA

batteries.

Replace the cover.

Installation

Optimum reception of colour requires a good signal and will generally mean that an outdoor antenna must

be used. The exact type and position of the antenna will depend upon your particular area.

/ It is recommended that the 75-ohm coaxial cable be used to eliminate interference and noise which

may occur

due to radio wave conditions.

/ The antenna cable should not be bundled with the power cord and the like.

/ If the antenna is not installed properly, contact your dealer for assistance.

Notes:

INSTALL the unit in a room where direct light will not fall upon the screen. Total darkness or a reflection on

the picture screen may cause eyestrain. Soft and indirect lighting is recommended for comfortable

viewing.

Antenna installation

8

Wall Antenna

Socket

RF Coaxial Cable(75 ohm)

Bronze Wire

Antenna Input

Connecting video and audio equipment

VIDEO EQUIPMENT

W

Y

R

This TV set provides 2 groups of AV input terminals and one group of COMPONENT input terminals for your

convenient connection to VCR, DVD or other video equipment to enjoy the high quality picture.

Please refer to the owner's manual of the equipment to be connected as well.

Connecting Rear AV Input Terminals

Signal

9

Connect the Audio/Video cables between the Audio(L,R)/Video terminal on the unit and the video equipment.

For better video, you can use the S-Video terminal if your source supports it.

To view the program from the AV1 input terminals, please press INPUT button on the remote control repeatedly until

AV1 appears on the

screen.

Connect Side AV Input Terminals

To Video output

o Aud o ut uts

T

i

op

Installation (continued)

To view the program from the AV2 input terminals, please press INPUT button on the remote control

repeatedly until AV2 appears on the screen.

Note:

S-VIDEO input uses the same circuit as

VIDEO1, and the S-VIDEO terminal

overrides the VIDEO1 terminal. When

both S-video and video1 signal are input,

the S-video

signal is selected and the

OSD is "SVIDEO". To view video1 signal,

disconnect the S-VIDEO connection.

VIDEO EQUIPMENT

To S-Video input

To Video input

To Audio inputs

To S-Video output

To Video output

To Audio outputs

R

Y

w

R

Y

: Yellow (video)

: White (audio L/MONO)

: Red(audio R)

VIDEO OUT

S-VIDEO OUT

L

AUDIO OUT

R

Y

w

S-VIDEO

VIDEO

L/MONO

R

VIDEO

L

AUDIO

R

AUDIO

(1)

RF

Y

C

b

C

r

L/MONO

R

AUDIO

VIDEO

L/MONO

R

(2)

10

Installation (continued)

Connecting DVD input

Connect the component video cable between Y, CB,CR input terminals on the unit and Y, CB,CR output terminals on

the

DVD player.

Connect the Audio cable between the audio input terminals on the unit and audio output terminals on the DVD

player.

To view the program from the COMPONENT input terminals, please press INPUT button on the remote control

repeatedly until COMPONENT appears on the screen.

Note:

This unit can only receive YC

bCr

signal but not YP

bPr signal through

DVD input.

G

B

R

W

L

COMPONENT OUTPUT

AUDIO OUTPUT

Y

C

b

C

r

R

w

R

G

B

:White (audio L/MONO )

:Green (Y)

:Blue (C

b)

:Red (audio R,Cr)

Video Cable

Audio Cable

DVD Player, STB, etc

S-VIDEO

VIDEO

L/MONO

R

VIDEO

L

AUDIO

R

AUDIO

(1)

RF

Y

C

b

C

r

L/MONO

R

AUDIO

11

Installation (continued)

Connecting the AV outputs

You can connect an audio system to the AV output terminals on the TV set rear to enjoy a high-quality sound from the

audio system, or you can connect the AV output terminals to the VCR to record the program you like.

R

Y

w

R R

Y

w w

VIDEO IN

R

L

AUDIO IN

w

R

Y

: Yellow (video)

: White (audio L)

: Red(audio R)

To Video output

To Audio outputs

To Video input

To Audio inputs

VCR for Recording

Audio System

To Audio inputs

S-VIDEO

VIDEO

L/MONO

R

VIDEO

L

AUDIO

R

AUDIO

(1)

RF

Y

C

b

C

r

L/MONO

R

AUDIO

12

Basic Operation

Turning on

Turning off

1

4 The TV set can turn off automatically by Sleep timer function

(needs to be set in advance).

4 If there is no input signal for 15 minutes, the TV set can turn off

automatically.

4 After you turn off the TV, you should wait at least 5 seconds if

you want

to turn the TV on again.

2

In STANDBY mode, press the Power button on the

TV set or on the remote controller and the TV set will

be turned on.

If no picture appears and the standby indicator lights up, then the TV

set is in STANDBY mode. Now please follow step 2.

Notes:

Press the Power button on the remote controller or

on the TV set to turn off the TV set.

Insert the AC plug into a conveniently located AC

outlet.

The AC plug supplied with the unit is polarized to help minimize the

possibility of electric shock. If the AC plug does not fit into a

nonpolarized AC outlet, do not file or cut the wide blade. It is the

user's responsibility to have an electrician replace the obsolete

outlet.

To prevent electric shock, do not use a

(polarized) plug with an extension cord

receptacle or other outlet unless the blades

can be fully inserted.

1

If you do not intend to use your TV for an extended

period of time, unplug the power cord from the power

outlet.

2

Power On/

Standby

13

Note:

lTo clearly introduce the menu operations , this operation manual provides a description based on operation with

the remote control.

lThe illustrations and on-screen displays in this manual are for explanation purposes(some are enlarged, others

cropped) and may vary slightly from the actual ones.

Menu navigation

With the power on, press the MENU button to display the main menu.

1

Press or button to select menu.65

2

Press button to enter the menu.3or4

3

Within the menu, use or to select, use to adjust or enter sub-menu.65 3or4

4

Press MENU button to return to the previous menu.

Press EXIT button to exit the main menu and return to your program.

5

Basic Operation

(continued)

Navigating the menus

This unit has a simple, easy-to-use menu system that appears on the screen. This system makes it convenient and

fast to use features on the unit. You can also display the status of TV features while watching a program.

PICTURE

P.LOCK

CLOCK

PRESET

EXTRA

Main Menu Overview (TV Mode)

MAIN MENU

PICTURE

CONTRAST

BRIGHTNESS

COLOR

TINT

SHARPNESS

PARENTAL

LOCK

CHANGE

PASSWORD

P.LOCK

ON

TIMER

CLOCK

DST

AUTO

CLOCK

ZONE

CLOCK

AUTO

PROGRAM

CH

SETUP

PRESET

ANTENNA

STRAT

AUTO PROGRAM

CH

NO

SKIP

LABEL*

DIG

SIGNAL*

CH SETUP

CLOSED

CAPTION

MENU

LANGUAGE

AUDIO

LANGUAGE

EXTRA

CC

DISPLAY

CC

SETTING

CLOSED CAPTION

MPAA

RATING

TV

RATING

CANADA

ENGLISH

CANADA

FRENCH

RATINGS LOCKS

LOCK

RATINGS

LOCKS

PARENTAL LOCK

CC

TYPE

CC

MODE*

CC

CUSTOMER*

CC SETTING

Note:

! Items marked with * do not appear in all modes.

! Some menu items are grayed out and are not selectable.

Press INPUT button on the remote controller.

Press this button repeatedly until the picture of TV program appears.

Watching AV program

Switching from AV to TV

14

To watch a video program from AV inputs, press INPUT button

repeatedly until you see the appropriate input indicator on the

screen.

This TV set provides 2 groups of AV input terminals and one group of

COMPONENT input terminals for your convenient connection to

VCR, DVD or other video equipments.

AV1

COMPONENT

AV2

Note: S-VIDEO input uses the same circuit as VIDEO1, and the S-

VIDEO terminal overrides the VIDEO1 terminal. When both S-video

and video1 signal are input, the S-video signal is selected and the OSD

is "SVIDEO". To view video1signal, disconnec t the S-VIDEO

connection.

8-0

MONO

DISPLAY

button

Select Input

Source

GUIDE

button

Basic Operation (continued)

Displaying the information banner

The information banner displays status information such as

channel number and signal source. Depending on the mode,

different information is displayed. In DTV mode, more information

(such as channel number and channel name, signal resolution,

etc.) can be displayed.

Press DISPLAY

button and the information banner appears.

Using the program guide

You can press GUIDE button on the remote control

to display guide information if available. You can

obtain program broadcasting time and program

name from the guide.

Note:

The GUIDE works only with digital channels.

(Example)

GUIDE

07:00PM-08:00PM WGBH-S

WGBH DTV Broadcast Signal

08:10PM-10:00PM WGBH-S

WGBH DTV Broadcast Signal

1/1

Press3or4 to scroll page if

there are two or more pages.

Tuning in

Press6 button to select START item.

Press 3 or 4 button to start

Auto Program.

Press5or 6 button to select

PRESET item.

15

Press MENU button.

Press 3or 4 button to enter

PRESET menu.

To enter the PRESET menu

4

Press 3 or 4 button to enter AUTO PROGRAM sub

menu.

In AIR mode, the set receives antenna

signals. In CABLE mode the set receives

Cable TV programs. Please select:

AIR: If using VHF/UHF antenna.

CABLE: If using Cable TV.

Auto program

3

Highlight ANTENNA item, press 3 or 4 button to select

AIR or CABLE.

1

2

Enter the PRESET menu, highlight AUTO PROGRAM

item.

AUTO PROGRAM

CH SETUP

PRESET

MAIN MENU

PICTURE

P

.LOCK

CLOCK

PRESET

EXTRA

ANTENNA

START

AUTO

PROGRAM

AIR

When you turn on the TV for the first time, you should perform an

auto program to set up stations on your TV. Below is the steps.

The unit begins to search and memorize all available programs.

Please wait patiently since it will take some time to finish

searching.

Note:

The

TV set will first memorize analog programs. After all

available analog programs have been memorized, it begins to

memorize DTV programs. During analog program memorizing,

you can press MENU button to stop it, then the TV turns to

memorize DTV programs. If you want to stop DTV program

memorizing,

just press MENU button again.

Menu navigation

button

MENU

Exit the menu

4

6

5

Press 5or 6button to select CH NO. item.

Press 6 button to select SKIP item.

Press 3or4 button to select a channel number (for

example, channel 2-2).

Press 3or 4button to set to ON.

Now channel 2-2 will be skipped when

you browse channels by CH+/- button.

To restore a skipped channel, please

use digit buttons to select the skipped

channel, then repeat the above steps

and set the SKIP item to OFF.

Skipping an unnecessary channel

3

16

Checking the DTV signal strength

Viewing channel label (Only for DTV programs)

Tuning in (continued)

Enter the PRESET menu, press 5or 6 button to select CH

SETUP item.

Press 3 or 4 button to enter CH SETUP menu.

1

2

AUTO PROGRAM

CH SETUP

PRESET

CH NO

SKIP

CH SETUP

2-2

ON

LABEL

WGBH-DX

DIG SIGNAL

25DB

Enter the PRESET menu, press 5or

6 button to select CH SETUP item,

press 3 or 4 button to enter CH

SETUP menu. Now the menu bottom

line shows the signal strength for the

current DTV channel.

CH NO

SKIP

CH SETUP

2-2

ON

LABEL

WGBH-DX

DIG SIGNAL

25DB

After saving channels into memory, you can skip unnecessary

channels so that only the channels you want to watch are selected

with the CH+/- buttons.

You can check the strength of your DTV signal and determine

whether you need to adjust your antenna or digital cable input. The

stronger the signal

strength, the less likely you are to experience

picture degradation.

You can make use of the information banner to know the channel

label for the current DTV program. You can also open the CH

SETUP menu and view the channel label . Note that the channel

labels are automatically assigned and

can not be changed by users.

Menu navigation

button

MENU

Exit the menu

17

Channel Selection

3

Use CH+ or CH- button

Use previous channel button

Press CH+ button, the channel number increases;

Press CH- button, the channel number decreases.

Press this button to switch between the current channel and the

previous channel.

2

Using the number pad

Press the number buttons (0-9) and the dash (-) button, then wait for

some seconds (or press ENTER button) to go directly to that channel.

For example, if you want to select channel 8-3, press 8-3 on the remote

control. (Make sure that you press the buttons within three seconds of

each other, or the channel won’s be entered correctly.)

Note: In some situations, virtual channel numbers do not correspond

to physical frequencies.

1

Information about USA channel numbering

= ATSC PSIP channel has two part channel number:

— Major channel number

— Minor channel number

=In US, in most situations the major channel number is same for both

analog and digital channels (It is equal to the NTSC channel number for

existing broadcasters.)

=In US, a minor channel

number of zero is used for a broadcaster’s analog

channel.

Channel Numbering Example

= Original NTSC Channels for Des Moines:

— 5, 8, 11, 13, 17

= Possible NTSC + ATSC Channels for Des Moines:

— 5-0, 8-0, 11-0, 13-0, 17-0 (channel numbers for existing analog

channels)

— 5-1, 5-2, 8-1, 8-2, 8-3,8-4, 13-1 (channel numbers for digital

channels)

For example:

Channel: 5-1

Major channel number

Minor channel number

Channel selection

Direct

select

DASH button

Previous channel

Channel

up/down

ENTER button

18

1

Use VOL+ or VOL- button.

Press VOL+ button, the volume increases;

Press VOL- button, the volume decreases.

2

If you want to mute the sound, press

MUTE button on the remote.

To resume the sound, press this

button again.

Notes:

Sound Control

26VOLUME

4 You can also resume the sound by pressing VOL+ button.

4 If you mute the sound the color of VOLUME displayed on the screen

is red, after resuming the sound the color of VOLUME displayed on

the screen is green.

Use MUTE button.

Sound mute

Volume up/down

Setting up Stereo/SAP broadcasts

This TV can receive MTS stereo programs and any SAP

(Secondary Audio Program) that may accompany the stereo

program. This type of signal is available only from analog

channels.You can select Stereo or SAP only when the TV

station transmits these signals. Mono sound is automatically

received if the broadcast is

only in monophonic. You can also

select MONO if you are having difficulty receiving a stereo

signal.

Press the MTS/SAP button repeatedly to select the MTS

mode.

MTS/SAP button

Adjusting Picture

Press 5or 6 button to select item.

Press 3or 4 button to adjust.

Press PICTURE button to select picture mode.

Item

Press 3

Press 4

Contrast

weaker

stronger

Color

paler deeper

Brightness

darker

lighter

Sharpness

softer

sharper

Tint

purplish

greenish

There are three preset picture modes (STANDARD, DYNAMIC and

SOFT) and one user-set picture mode (PERSONAL) .

You can quickly select Picture mode by pressing the PICTURE

button on the remote control.

STANDARD: Select for a normal picture.

DYNAMIC: Select for a bright and dynamic picture.

SOFT: Select for

a finely detailed picture.

PERSONAL: The picture quality you set.

Adjusting picture

1

2

3

4

19

Press MENU button.

Now the PICTURE item is highlighted automatically.

Press3or4button to enter PICTURE menu.

CONTRAST

20

Changing picture size (only in DTV mode)

You can change picture size (aspect ratio) according to your

video signal type or personal preference.

When the video signal type is in16:9 format, press the ZOOM

button to select the desired picture size (aspect ratio). You can

select between NORMAL and ZOOM.

PICTURE

CONTRAST

BRIGHTNESS

COLOR

TINT

SHARPNESS

50

40

0

40

Menu navigation

button

MENU

ZOOM

PICTURE

Exit the menu

Page is loading ...

Memorex mt2026D User manual

This manual is also suitable for

Memorex mt2026D User manual

in other languages

Other documents