Wharfedale Pro Connect Series User manual

Brand: Wharfedale Pro

Model: Connect Series

Category: DJ controllers

Type: User manual

OPERATING MANUAL AND USER GUIDE

Q Series Equalizers

Q Series Q130 / Q215 / Q230

www.wharfedalepro.com

OPERATING MANUAL AND USER GUIDE

IMPORTANT WARNINGS & SAFETY INSTRUCTIONS

1. READ ALL INSTRUCTIONS carefully and become familiar with the features and functions of these

products before operating them.

2. RETAIN THESE INSTRUCTIONS for future reference.

3. COMPLY WITH ALL WARNINGS – All warnings and instructions for this product should be adhered to.

4. USE WITH AMPLIFIERS – In order to avoid damage to drivers and other equipment, it is advisable to

establish and follow a routine for powering up and powering down a sound system. With all system

components connected, turn on source equipment (mixers, signal processors, record and playback

units, etc.) BEFORE powering up amplifiers. Transient voltages from powering up source equipment

can damage speakers if amplifiers are already turned on. Make sure that amplifier volumes are

set to their minimum settings and power up any system amplifiers LAST. It is recommended that

all system components be allowed to stabilize for several seconds before any source signals are

introduced or level setting adjustments are made. Similarly, when shutting systems down, turn all

amplifiers off first, before powering down any other system components.

5. CABLES – Do not use shielded or microphone cables for connection between amplifiers and speakers.

Use only approved speaker cables with proper connectors.

6. MAINS SUPPLY AND SAFETY – The main operating voltage of Wharfedale electronics is shown on the

rear panel of the device. If it does not match the voltage in your area, contact your dealer.

7. CAUTION – Professional sound reinforcement systems are capable of generating very high sound

pressure levels and use high voltage. Use care with placement and operation to avoid exposure to

excessive volume levels, water or moisture.

8. SERVICE – There are no user serviceable parts inside this product. Users should not attempt to service

this product. Warranty nullification could result if this is attempted.

Series

1. Important Warnings & Safety Instructions……………………………....…….…1

2. What about the Q Series Equalizers?………………………………....….….......3

3. Introduction/Overview…………………………….……….................................4

4. Features……………………….…………………………………….……………........5

5. Setting up/ Connections/ Wiring……………………………………...................7

6. Specifications…………………………………….………………………….……….11

7. Dimensional Drawings……………………………………................................12

8. Warranty…………………………..……....…………………………..……............12

TABLE OF CONTENTS

OPERATING MANUAL AND USER GUIDE

The Q Series consists of three models: Q130 is a high quality, constant Q, 1/3 octave,

Graphic Equalizer; The Q215 is a high quality constant Q, 2/3 Octave Equalizer and the

Q230, dual channel, constant Q, 1/3 Octave Equalizer. They are designed to provide

transparent and accurate frequency shaping capability in an easy to use package.

The separate frequency bands, ranging from 25 Hz to 20kHz allow you to “tune” the sound

system to the room to create the best sounding system. Using long throw faders makes fine

adjustments of each band easy and accurate. Other features include a by-pass switch to

allow you to compare the equalized sound from the unfiltered sound, thereby allowing you

to fine tune the system.

The Q Series uses balanced and unbalanced Input/Output connectors to allow you to use

it in a variety of applications. The rack-mountable chassis allows you to quickly install the

units into an equipment rack or your audio cabinet.

WHAT ABOUT THE Q Series Equalizers?

Series

Wharfedale Q Series Equalizers are the result of many years of experience in the use,

design and manufacturing of professional sound reinforcement products. We take great

pride in engineering and building every Wharfedale Pro product and wish to thank you for

entrusting us with your sound.

From the time Gilbert Briggs built his first loudspeaker in 1932, to the present, Wharfedale

Professional products have maintained the same standard of quality in components,

workmanship and performance.

Please take a few minutes to read this manual completely in order to ensure that you get

the most out of your equalizers.

Q SERIES EQUALIZER OVERVIEW:

The Q Series Equalizers are accurate, high quality, Constant Q graphic equalizers. This

allows you to tailor your sound to make it sound the best in a room or tailor the sound of

your music. With low distortion and flexible features, these equalizers are the right tools to

bring to the show.

The Q Series has many user-friendly features. These easy to adjust and use features include,

long travel slide faders (Q-130), by-pass switch, soft limit switch, variable high pass filter

control and easy to read LED meters.

INTRODUCTION

OPERATING MANUAL AND USER GUIDE

♦

Three models

o Q-230: Two Channel 30 band, 1/3 Octave Equalizer

o Q-130: Single Channel 30 band, 1/3 Octave Equalizer

o Q-215: Two Channel 15 band, 2/3 Octave Equalizer

♦

Constant Q

♦

By-pass switch

♦

Soft Limit Switch

♦

Variable High pass filter 10Hz – 200Hz (Q-130)

♦

Variable High pass filter 10Hz – 100Hz (Q-230)

♦

Easy to read LED meters

♦

Professional long throw slide faders (Q-130)

♦

XLR/ 1/4” TRS balanced/unbalanced inputs/outputs

♦

Output Ground lift switch

FEATURES

Series

SIGNAL INPUT

MIC, CD etc. TO MIXER

MIXER

OUTPUT

INPUT TO

GRAPHIC EQUALISER

OUTPUTS FROM GRAPHIC

EQUALISERTO CROSSOVER

INPUTS TO CROSSOVER

SEPARATE

HIGH/MID

AND LOW

OUTPUTS TO

AMPLIFIER(S)

FROM

CROSSOVER

INPUTS TO AMPLIFIER(S)

SEPARATE

LOW

SPEAKER

OUTPUT TO

LOW

FREQUENCY

SPEAKER

FROM

AMPLIFIER

SEPARATE

HIGH/MID

SPEAKER

OUTPUT TO

HIGH/MID

SPEAKER

FROM

AMPLIFIER

= SIGNAL (SHIELDED) CABLE

= LOUDSPEAKER (NON-SHIELDED) CABLE

TYPICAL WIRING DIAGRAM FOR THE Q130 CROSSOVER IN SYSTEM SETUP

BLOCK DIAGRAM

OPERATING MANUAL AND USER GUIDE

The Q Series Equalizers are easy to install and operate.

Before plugging in the Q Series Equalizers, or any electrical audio device, be sure that the

power switch is in the off position, the volume control is all the way down (at 0 level) and all

audio connections are made.

After power-up, speak into your mic start the CD or MP3 player or other line level device

and slowly increase the volume to the desired level. Avoid distortion (or overdriving the

input) as it can damage your system in the long term. If you cannot achieve the desired

sound level in your system, you must add more speakers or a subwoofer to the system.

CONNECTIONS / WIRING

Connecting Q Series Equalizers to your system is straightforward. You simply plug in your

cables (microphone or line level) from the output of the mixer to the input of the EQ; then

from the EQ output to an amplifier. Always use good quality microphone (2 conductor +

shield) cable. After you plug in the components, you must adjust the sound level to produce

the best sound. A good place to start is the mixer then EQ then amplifier.

SETTING UP

Series

Gain Stage Adjustments:

• Plug the mic in and position the volume control at ´0´ (zero) dB. Keep the main output

volume down as well as the other components volume controls.

• Whilst watching the meters, speak or sing (it’s always good to warm up your voice) into

the mic in the same way as your performance and adjust the GAIN control, usually at the

top of the mixer channel near the mic input jack, to the point where the meters spend a

lot of time at or near the ´0dB´ (zero). An occasional red peak light is OK, just make sure

the meters are not in the red area very long.

• Next adjust the main output so that the meters are at the ´0´ (zero) position most of the

time, or at the loudest part of your performance. This takes time and practice to get the

best sound.

• The next stop is the EQ. The idea of all these adjustments is be sure you get the best

and cleanest signal going down the line. Start with the gain or volume control in the 0

position.

• The next step: Tuning the room (a/k/a ringing out the system). See page 9,10.

• In a simple system, the next component is the amplifier. Because your previous

adjustments have resulted in the cleanest, loudest sound coming from the mixer to the

EQ, it is not uncommon for the volume controls on the amplifier to be less than maximum

(a/k/a “11”). Don ’ t worry, this means you have plenty of room to get louder. If your

amplifier volume control is “max ’ d out” when you are at this point in the setup, you

have no place to go. You must add to your system; either more amps or more speakers.

• The bottom line is to keep watch over your meters, they will tell you if the sound levels

throughout the system are in keeping with good practices.

OPERATING MANUAL AND USER GUIDE

Tuning the Room:

• The controls on the Equalizer provide level adjustment to frequencies in the audio

spectrum. You adjust them either louder (up) or quieter (down) to make the overall sound

in the room better.

• To tune the system to the room, it takes some practice and patience. You play PINK

NOISE through the system and adjust each frequency so that the response is the same

for every frequency. You can download pink noise and save it to CD or MP3/4 player.

• To effectively measure and adjust the system response, you will need a Real Time

Analyzer (RTA). This device displays the system frequency response. They are available in

rack mounted, hand held and software formats.

• When your ear gets calibrated, you can tune the system by ear.

• Using pink noise through the system and an RTA, adjust the frequency response of

the system to look flat. Minor adjustments by ear can be made later, but only minor

adjustments.

• Leave the EQ alone until the next gig or the room changes significantly. However, if it

changes too much, it is too late to run the above procedure and you must “do it by ear”

• Use the individual channel EQ on the mixer to get the music and vocals to mix properly.

A graphic equalizer is a very valuable tool for the traveling musician. It allows you to get

the best sound in a variety of venues. As we know, all rooms are not created equal. They

have their own personality. That is to say, your sound system will not sound the same from

room to room. Using the EQ correctly will help you maintain “your sound”.

Series

Q Series with connections shown

OPERATING MANUAL AND USER GUIDE

SPECIFICATIONS

INPUT/ OUTPUT

Connectors:

Type:

Input Impedance:

Max Input Level:

CMRR:

Type:

Output Impedance:

Max Output Level:

SYSTEM PERFORMANCE

Bandwidth:

Frequency Response:

Dynamic Range:

Signal-to-Noise:

THD + Noise:

Interchannel Crosstalk:

FUNCTION SWITCHES

EQ Bypass:

Low Cut:

Range:

POWER SUPPLY

Operating Voltage:

Power consumption:

Mains Connection:

DIMENSIONS/WEIGHT

Dimension:

Weight

Q-130

1/4" TRS, female XLR

(pin 2 hot)

Electronically balanced/

unbalanced, RF filtered

Balanced 20k ohm, unbalanced

10k ohm

>+21dBu balanced or unbalanced

>40dB, typically >55dB at 1kHz

Impedance-balanced/

unbalanced, RF filtered

Balanced 100 ohm, unbalanced 50

ohm

>+21dBu balanced/ unbalanced

into 2k ohm or greater

20Hz to 20kHz, +0.5/-1dB

<10Hz to >50kHz, +0.5/-3dB

108 dB

90 dB

<0.004%

<-80dB, 20Hz to 20kHz

Bypasses the graphic equalizer

section in the signal path

Activates the 50Hz 12dB/

octave high-pass filter

Selects either +/- 6dB or

+/-12dB slider boost/cut range

100VAC 50/60Hz, 120VAC

60Hz, 230VAC 50/60Hz

12W

IEC receptacle

482.6 x 170 x 88 mm

4.0 kg

Q-230

1/4" TRS, female XLR

(pin 2 hot)

Electronically balanced/

unbalanced, RF filtered

Balanced 20k ohm, unbalanced

10k ohm

>+21dBu balanced or unbalanced

>40dB, typically >55dB at 1kHz

Impedance-balanced/

unbalanced, RF filtered

Balanced 100 ohm, unbalanced 50

ohm

>+21dBu balanced/ unbalanced

into 2k ohm or greater

20Hz to 20kHz, +0.5/-1dB

<10Hz to >50kHz, +0.5/-3dB

108 dB

90 dB

<0.004%

<-80dB, 20Hz to 20kHz

Bypasses the graphic equalizer

section in the signal path

Activates the 50Hz 12dB/

octave high-pass filter

Selects either +/- 6dB or

+/-12dB slider boost/cut range

100VAC 50/60Hz, 120VAC

60Hz, 230VAC 50/60Hz

12W

IEC receptacle

482.6 x 168 x 88 mm

3.93 kg

Q-215

1/4" TRS, female XLR

(pin 2 hot)

Electronically balanced/

unbalanced, RF filtered

Balanced 20k ohm, unbalanced

10k ohm

>+21dBu balanced or unbalanced

>40dB, typically >55dB at 1kHz

Impedance-balanced/

unbalanced, RF filtered

Balanced 100 ohm, unbalanced 50

ohm

>+21dBu balanced/ unbalanced

into 2k ohm or greater

20Hz to 20kHz, +0.5/-1dB

<10Hz to >50kHz, +0.5/-3dB

108 dB

90 dB

<0.004%

<-80dB, 20Hz to 20kHz

Bypasses the graphic equalizer

section in the signal path

Activates the 50Hz 12dB/

octave high-pass filter

Selects either +/- 6dB or

+/-12dB slider boost/cut range

100VAC 50/60Hz, 120VAC

60Hz, 230VAC 50/60Hz

12W

IEC receptacle

482.6 x 168 x 44mm

2.96 kg

Series

Wharfedale Pro products are warranted of manufacturing or material defects for a period of one

year from the original date of purchase. In the event of malfunction, contact your authorized

Wharfedale Pro dealer or distributor for information.

*Be aware that warranty details may differ from country to country. Contact your dealers or

distributor for information. These terms do not infringe your statutory rights.

WHARFEDALE PRO LIMITED WARRANTY

Dimensional

Q130

435.00

482.60

44.00

482.60

88.00

435.00

88.00

482.60

88.00

434.00

88.00

Q215

Q230

Wharfedale Professional

IAG House, 13/14 Glebe Road, Huntingdon, Cambridgeshire, PE29 7DL, UK

www.wharfedalepro.com

Wharfedale Professional reserves the right to alter or improve specifications without notice.

Wharfedale Pro Connect Series User manual

Brand: Wharfedale Pro

Model: Connect Series

Category: DJ controllers

Type: User manual

Download PDF

report

Wharfedale Pro Connect Series User manual

Wharfedale Pro Connect Series User manual

Related papers

Other documents