Briggs & Stratton 01813-0 User manual

Page is loading ...

2
Briggs & Stratton Power Products Automatic Transfer Switch
Installation and Owner’s Manual
TABLE OF CONTENTS
TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
For the Home or Business Owner: . . . . . . . . . . . . . . 4
For the Installing Dealer/Contractor: . . . . . . . . . . . . . 4
Owner Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installer Responsibilities . . . . . . . . . . . . . . . . . . . . . . . . 4
Equipment Description. . . . . . . . . . . . . . . . . . . . . . . . . 5
INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Delivery Inspection . . . . . . . . . . . . . . . . . . . . . . . . 5
Shipment Contents . . . . . . . . . . . . . . . . . . . . . . . . 5
Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . . 5
Mounting Guidelines . . . . . . . . . . . . . . . . . . . . . . . 6
Power Wiring Interconnections . . . . . . . . . . . . . . . . 6-7
SYSTEM OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TESTING THE AUTOMATIC TRANSFER SWITCH . . . . 8
Automatic Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Utility Fail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Engine Warm-Up . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Utility Pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Retransfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Engine Cool Down . . . . . . . . . . . . . . . . . . . . . . . . 8
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Model 01813 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Model 01814 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
When Calling The Factory . . . . . . . . . . . . . . . . . . . . . . 8
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
DIAGRAMS, EXPLODED VIEWS, PARTS LISTS . . . . . 10-13
NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3

Briggs & Stratton Power Products Automatic Transfer Switch

Installation and Owner’s Manual

SAFETY RULES

This is the safety alert symbol. It is used to

alert you to potential personal injury

hazards. Obey all safety messages that follow

this symbol to avoid possible injury or death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION,WARNING), a pictorial and/or a

safety message to alert you to hazards. DANGER indicates

a hazard which, if not avoided, will result in death or

serious injury. WARNING indicates a hazard which, if not

avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, might

result in minor or moderate injury. CAUTION, when

used without the alert symbol, indicates a situation that

could result in equipment damage. Follow safety messages

to avoid or reduce the risk of injury or death.

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard.The warnings in

this manual, and the tags and decals affixed to the unit are,

therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that it

is safe for you and others.You must also make sure that the

procedure, work method or operating technique that you

choose does not render the transfer switch unsafe.

• DO NOT touch bare wires or receptacles.

• DO NOT use transfer switch with worn, frayed, bare or

otherwise damaged wiring.

• DO NOT handle electrical cords while standing in water,

while barefoot, or while hands or feet are wet.

• If you must work around a unit while it is operating, stand on

an insulated dry surface to reduce shock hazard.

• DO NOT allow unqualified persons or children to operate or

service transfer switch.

• In case of an accident caused by electrical shock, immediately

shut down the source of electrical power and contact local

authorities. Avoid direct contact with the victim.

Failure to properly ground transfer switch can

result in electrocution.

WARNING

Only qualified electricians should attempt installation

of this system, which must strictly comply with

applicable codes, standards and regulations.

WARNING

• Use transfer switch only for intended uses.

• If you have questions about intended use, ask dealer or

contact Briggs and Stratton Power Products.

• DO NOT expose transfer switch to excessive moisture, dust,

dirt, or corrosive vapors.

• Despite the safe design of the transfer switch, operating this

equipment imprudently, neglecting its maintenance or being

careless can cause possible injury or death.

• Remain alert at all times while working on this equipment.

NEVER work on the equipment when you are physically or

mentally fatigued.

• If connected devices overheat, turn them off and turn off their

circuit breaker/fuse.

Improper treatment of transfer switch can damage it

and shorten its life.

CAUTION

4

Briggs & Stratton Power Products Automatic Transfer Switch

Installation and Owner’s Manual

INTRODUCTION

Thank you for your purchase of this Briggs & Stratton

Power Products Automatic Transfer Switch.This product is

intended for use with Briggs & Stratton Home Standby

Generator sets ONLY.This is an optional home standby

system which provides an alternate source of electric

power and to serve loads such as heating, refrigeration

systems, and communication systems that, when stopped

during any power outage, could cause discomfort, or the

like.This product DOES NOT qualify for emergency

standby as defined by NFPA 70 (NEC).

Briggs and Stratton Power Products (BSPP) has made every

effort to provide for a safe, streamlined and cost-effective

installation. Each installation is unique, it is impossible to

know of and advise of all conceivable procedures and

methods by which installation might be achieved.We could

not know of possible hazards and/or the results of each

method or procedure. For these reasons,

Only licensed electrical contractors should

install transfer switches. Installations must

strictly comply with all applicable federal,

state and local codes, standards and

regulations.

Your BSPP Transfer Switch is supplied with this combined

“Installation and Owner’s Manual”.This is an important

document and should be retained by the owner after the

installation has been completed.

Every effort has been expended to make sure that the

information in this manual is both accurate and current.

However, the manufacturer reserves the right to change,

alter or otherwise improve the system at any time without

prior notice.

For the Home or Business Owner

To help you make informed choices and communicate

effectively with your installation contractor(s),

Read and understand the

Owner Orientation Section of this manual

BEFORE

contracting or starting

your transfer switch installation.

To arrange for proper installation, contact the store at

which you purchased your BSPP Transfer Switch, your

dealer, or your utility power provider.

The Transfer Switch Warranty is VOID

unless the system is installed by a

licensed electrical professional.

For the Installing Dealer/Contractor

Check federal, state and local codes for questions on

installation.

If you need more information about the transfer switch,

call 1-800-743-4115, between 8:00 AM and 5:00 PM CT.

Owner Orientation

The illustrations are for typical circumstances and are

meant to familiarize you with the installation options

available with your transfer switch.

Local codes, appearance, and distances are the factors that

must be considered when negotiating with an installation

professional.As the distance from the existing electrical

service increases, compensation in wiring materials must be

allowed for.This is necessary to comply with local codes

and overcome electrical voltage drops.

The factors mentioned above will have a direct effect

on the overall price of your transfer switch installation.

NOTE: Your installer must check local codes AND obtain

permits before installing the system.

• Read and follow the instructions given in this manual.

• Follow a regular schedule in caring for and using your

transfer switch, as specified in the manual.

Installer Responsibilities

• Read and observe the safety rules.

• Read and follow the instructions given in this manual.

• Check federal, state and local codes.

5

Briggs & Stratton Power Products Automatic Transfer Switch

Installation and Owner’s Manual

Equipment Description

These switches are a new generation of transfer switches

that are intended to transfer the entire load of normal

residential installations.The load is connected either to

utility power (normal) or home standby power

(emergency).The transfer switch monitors utility and

generator voltages and will automatically connect to the

appropriate source of power.

Major components of the transfer switch are a 2 pole

double throw transfer switch, control circuit board, fused

utility terminals and interconnecting wiring.

The transfer switch is solenoid-operated from utility or

generator inputs and contain suitable mechanical and

electrical interlock switches to eliminate the possibility of

connecting the utility service to the generator output. It

has ratings capable of switching full utility power into the

residence. In addition, a manual override lever is provided

for the transfer function.

The control circuit board has active circuits sensing utility

and generator voltages. It creates a signal for the generator

start-up, switch transfer, retransfer when utility is restored

and generator cool down periods.The control board also

contains red and green LED’s indicating the power sources

available and two relay operated contacts that provide

supervisory control of external loads.

INSTALLATION

Unpacking

Delivery Inspection

After removing the carton, carefully inspect the transfer

switch components for any damage that may have occurred

during shipment.

IMPORTANT: If loss or damage is noted at time of

delivery, have the person(s) making delivery note all damage

on the freight bill and affix his signature under the

consignor's memo of loss or damage. If loss or damage is

noted after delivery, contact the carrier for claim

procedures. Missing or damaged parts are not warranted.

Shipment Contents

• Automatic Power Transfer Switch

• Installation and Owner’s Manual

Mounting Dimensions

Figure 1 depicts the physical size and mounting hole

locations of the NEMA 3R automatic transfer switch

enclosure.This enclosure is suitable for indoor/outdoor use.

The transfer switch enclosure is commonly secured

through the predrilled holes, as shown.

Figure 1 — Automatic Power Transfer Switch Dimensions

Model 01813

Model 01814

Enclosure Dimensions

Mounting Dimensions

Enclosure Dimensions

Mounting Dimensions

6

Briggs & Stratton Power Products Automatic Transfer Switch

Installation and Owner’s Manual

Mounting Guidelines

The Automatic Transfer Switch is enclosed in a NEMA Type

3R enclosure suitable for indoor/outdoor use. Guidelines for

mounting the Automatic Transfer Switch include:

• Install the switch on a firm, sturdy supporting structure.

• The switch must be installed with minimum NEMA 3R

hardware for conduit connections.

• To prevent switch contact distortion, level and plumb the

enclosure.This can be done by placing washers between

the switch enclosure and the mounting surface.

• NEVER install the switch where any corrosive substance

might drip onto the enclosure.

• Protect the switch at all times against excessive moisture,

dust, dirt, lint, construction grit and corrosive vapors.

A typical installation of the Automatic Power Transfer

Switch is depicted in Figure 2. It is best if it is mounted

near the utility meter, either inside or outside. Discuss

layout suggestions/changes with the owner before beginning

the system installation process.

Power Wiring Interconnections

All wiring must be the proper size, properly supported and

protected by conduit.

Complete the following connections between the transfer

switch, main distribution panel, utility power and generator

(Figure 3, on next page).

1. Ensure utility power is turned OFF. Connect utility

power supply leads to transfer switch terminals

marked “UTILITY CONNECTION”.

2. Connect utility neutral to the transfer switch

“NEUTRAL” terminal.

3. Connect main distribution panel power leads to transfer

switch terminals marked “LOAD CONNECTION”.

4. Connect main distribution panel neutral lead to

transfer switch “NEUTRAL” terminal.

5. Connect generator power supply leads from the

generator’s control panel to transfer switch terminals

marked “GENERATOR CONNECTION”.

6. Connect generator Neutral from the control panel to

the transfer switch “NEUTRAL” terminal.

7. Connect generator “GND” from the control panel to

the transfer switch “GND” terminal.

8. Connect main distribution panel “GND” to the

transfer switch “GND” terminal.

9. Connect generator utility 240 VAC terminals to

transfer switch utility 240 VAC terminals.

10. Terminal strip on control module in transfer switch has

four connections for customer use.There are two sets

of “Normally Closed” contacts available.They will be

activated when generator power is required.These can

be used for supervisory control of large connected

loads on generator, for example, disconnecting air

conditioner, water heater, etc. or an alarm source.

11. Tighten all wire connections/fasteners to proper torque.

• Failure to follow above warning could cause damage and/or

malfunction of equipment.

Low voltage wire cannot be installed in same conduit

as power voltage wiring.

CAUTION

Figure 2 — A Typical Transfer Switch Mounting

Main

Breaker

Panel

Transfer Switch

Generator

Service

Disconnect

Watt-

Hourmeter

7

Briggs & Stratton Power Products Automatic Transfer Switch

Installation and Owner’s Manual

Figure 3 — A Typical Installation Diagram for Transfer Switch

MODEL 01813

MODEL 01814

Main

Main Distribution Panel

Ground Bus

Neutral

Bus

To Generator

Neutral

Terminal

To Utility Power

Normally

Closed

Contacts

Load

Connection

Ground Lug

Generator

Connection

Utility

Connection

Main

Main Distribution Panel

Ground Bus

Neutral

Bus

To Generator

Neutral

Terminal

To Utility Power

Normally

Closed

Contacts

Load

Connection

Ground Lug

Generator

Connection

Utility

Connection

8

Briggs & Stratton Power Products Automatic Transfer Switch

Installation and Owner’s Manual

SYSTEM OPERATION

To select automatic transfer operation, do the following:

1. Set service disconnect switch that sends utility power

to transfer switch to “On” position.

2. Set generator’s main circuit breaker to its “On”

position.

3. Install 15 Amp fuse in control panel on generator.

4. Set AUTO/OFF/MANUAL switch on generator to

“AUTO” position.

The system will now be in automatic operation mode.

TESTING THE

AUTOMATIC TRANSFER

SWITCH

Turn the service disconnect feeding the transfer switch, to

the “Off” position.The automatic sequence will follow.To

go back to utility power, turn the service disconnect to the

“On” position.

Automatic Sequence

Utility Fail

Utility voltage sensor senses when utility voltage is below

70 percent of nominal. Engine start sequence is initiated

after 6 second time delay.

Engine Warm-Up

Time delay to allow for engine warm-up before transfer

fixed at 20 seconds or 50 seconds with optional cold

weather package.

Transfer

Transfers from utility to standby supply occurs after

standby voltage is above set levels. Minimum engine run

time is 4 minutes after transfer.

Utility Pickup

Voltage pickup level is 80 percent of nominal voltage.

Retransfer

Retransfer from standby to utility supply 10 seconds after

utility voltage supply is above pickup level.

Engine Cool Down

Engine will run for 60 seconds after retransfer.

Specifications

UL® 1008 Listed Transfer Switch

Model 01813

Maximum Load/Circuit:

from Load Center . . . . . . . . . . 100 Amps

Rated AC Voltage. . . . . . . . . . . . . 250 Volts

Poles . . . . . . . . . . . . . . . . . . . . . . 2

Frequency . . . . . . . . . . . . . . . . . . 50/60 Hz

Fault Current Rating . . . . . . . . . . 22,000 RMS Symmetrical

Amperes

Supervisory Contacts Rating . . . 5 Amp, 125 Volt AC

Weight . . . . . . . . . . . . . . . . . . . . . 21 lbs.

Model 01814

Maximum Load/Circuit:

from Load Center . . . . . . . . . . 200 Amps

Rated AC Voltage. . . . . . . . . . . . . 250 Volts

Poles . . . . . . . . . . . . . . . . . . . . . . 2

Frequency . . . . . . . . . . . . . . . . . . 50/60 Hz

Fault Current Rating . . . . . . . . . . 25,000 RMS Symmetrical

Amperes

Supervisory Contacts Rating . . . 5 Amp, 125 Volt AC

Weight . . . . . . . . . . . . . . . . . . . . . 34 lbs.

When Calling the Factory

Before contacting Briggs and Stratton Power Products

regarding service or repair of this transfer switch, obtain

the Model Number and Serial Number from the unit data

decal located on or inside the case.

To contact Briggs and Stratton Power Products call

1-800-743-4115, between 8:00 AM and 5:00 PM CT.

9

Briggs & Stratton Power Products Automatic Transfer Switch

Installation and Owner’s Manual

TROUBLESHOOTING

Problem

Automatic transfer switch does

not transfer to generator

Automatic transfer switch does

not transfer to utility

Generator is still running after

switch transfers to utility power

Supervised loads (air conditioner,

etc.) are not operating when

utility is present

Cause

1. Generator breaker open.

2. Generator voltage not acceptable.

1. Service disconnect breaker open.

2. Utility voltage not acceptable.

Engine cool down period.

NC contacts not operating correctly.

Correction

1. Reset generator circuit breaker.

2. Refer to generator manual.

1. Reset service disconnect breaker.

2. Wait for utility voltage to return

to normal.

Engine should stop after 1 minute.

Check NC contact for proper

operation and/or check control wiring

to external load.

10

Briggs & Stratton Power Products Automatic Transfer Switch

Installation and Owner’s Manual

TRANSFER SWITCH SCHEMATIC

11

Briggs & Stratton Power Products Automatic Transfer Switch

Installation and Owner’s Manual

TRANSFER SWITCH WIRING DIAGRAM

12

Briggs & Stratton Power Products Automatic Transfer Switch

Installation and Owner’s Manual

TRANSFER SWITCH EXPLODED VIEW & PARTS LIST

Item Part # Description

1 192154GS ENCLOSURE

2 192155GS BACK PANEL

3 191995GS TRANSFER SWITCH, 100A, with

Cover & Handle

4 36701GS SCREW

5 36903GS SCREW

6 36905GS SCREW

7 36933GS SCREW

8 193159GS DECAL, Reinstall After

9 191668GS CONTROL, Board

10 192701GS SPACER, Nylon

11 B4856GS LUG, Ground

12 22097GS WASHER, Lock

13 22473GS WASHER

14 22127GS NUT

15 190841GS TERMINAL, Neutral

16 B4857GS FUSE

Item Part # Description

17 192151GS HOLDER, Fuse

18 192557GS STANDOFF, Purse Lock

19 190850GS DECAL,ATS, BSPP

20 192702GS DECAL,Term Strip

21 B5106GS DECAL, Connection, Utility

22 B5107GS DECAL, Connection, Generator

23 192688GS DECAL, 100A,ATS

24 192690GS DECAL, UL Listed, 100A,ATS

25 190992GS DECAL,Warning Shock

26 190984GS DECAL, Fuse

27 B4986GS DECAL, Ground

28 192597GS DECAL, Utility, 240V AC

29 192165GS DECAL,APPVD CB

30 193307GS DECAL, Load

31 23897GS WASHER

32 23762GS WASHER

33 36901GS SCREW

MODEL 01813

13

Briggs & Stratton Power Products Automatic Transfer Switch

Installation and Owner’s Manual

TRANSFER SWITCH EXPLODED VIEW & PARTS LIST

Item Part # Description

1 192156GS ENCLOSURE

2 192170GS BACK PANEL

3 192024GS TRANSFER SWITCH, 200A, with

Cover & Handle

4 36701GS SCREW

5 36903GS SCREW

6 36905GS SCREW

7 36901GS SCREW

8 193159GS DECAL, Reinstall After

9 191668GS CONTROL, Board

10 192701GS SPACER, Nylon

11 B4856GS LUG, Ground

12 22097GS WASHER, Lock

13 22473GS WASHER

14 22127GS NUT

15 192696GS TERMINAL, Neutral

16 B4857GS FUSE

Item Part # Description

17 192151GS HOLDER, Fuse

18 192557GS STANDOFF, Purse Lock

19 190850GS DECAL,ATS, BSPP

20 192702GS DECAL,Term Strip

21 B5106GS DECAL, Connection, Utility

22 B5107GS DECAL, Connection, Generator

23 192689GS DECAL, 200A,ATS

24 192691GS DECAL, UL Listed, 200A,ATS

25 190992GS DECAL,Warning Shock

26 190984GS DECAL, Fuse

27 B4986GS DECAL, Ground

28 192597GS DECAL, Utility 240V AC

29 192166GS DECAL,APPVD CB

30 193307GS DECAL, Load

31 23897GS WASHER

32 23762GS WASHER

MODEL 01814

14

Briggs & Stratton Power Products Automatic Transfer Switch

Installation and Owner’s Manual

NOTES

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC EQUIPMENT OWNER WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s), of the equipment that is defective in material

or workmanship or both. Transportation charges on parts submitted for repair or replacement under this warranty must be borne by

purchaser. This warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest

Authorized Service Dealer in our dealer locator map at www.briggspowerproducts.com.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY

AND ALL IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED

TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty

lasts, and some states or countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation

and exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state

to state or country to country.

OUR EQUIPMENT*

OUTBOARD

MOTOR

PRESSURE

WASHER

WATER PUMP

(Not available in the

USA)

PORTABLE

GENERATOR

WELDER

Less tthan 110 KKW Less tthan 110 KKW

TRANSFER

SWITCH

2 years

none

1 year

90 days

1 year

90 days

2 years

1 year

2 years

1 year

3 years or

1500 hours

1 year

WARRANTY PERIOD**

HOME GENERATOR SYSTEM

(Includes Transfer Switch, if sold with equipment.)

Consumer Use

Commercial Use

* The engine and starting batteries are warranted solely by the manufacturers of those products.

** 2 years for all consumer products in the European Union. Parts only on 2nd year for consumer use of Portable Generator and

Home Generator System - Less than 10 KW, outside of European Union.

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time

stated in the table above. “Consumer use" means personal residential household use by a retail consumer. “Commercial use" means all other

uses, including use for commercial, income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter

be considered as commercial use for purposes of this warranty. Equipment used for Prime Power in place of utility are not applicable to

this warranty. Electric Powered Pressure Washers used for commercial purposes are not warranted.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR

PROOF OF PURCHASE RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY

SERVICE IS REQUESTED, THE MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY

PERIOD.

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most

warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not

apply if equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation.

Similarly, the warranty is void if the manufacturing date or the serial number on the equipment has been removed or the equipment has been altered

or modified. During the warranty period, the Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to

be defective under normal use and service. This warranty will not cover the following repairs and equipment:

• Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This warranty does not

cover repair when normal use has exhausted the life of a part or the equipment.

• Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or unauthorized

installation or alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper maintenance, repair or storage so as,

in our judgment, to adversely affect its performance and reliability. This warranty also does not cover normal maintenance such as adjustments,

fuel system cleaning and obstruction (due to chemical, dirt, carbon, lime, etc.).

• Other Exclusions: This warranty excludes wear items such as quick couplers, oil gauges, belts, o-rings, filters, pump packing, etc., pumps that

have been run without water supplied or damage or malfunctions resulting from accidents, abuse, modifications, alterations, or improper servicing

or freezing or chemical deterioration. Accessory parts such as guns, hoses, wands and nozzles are excluded from the product warranty. Also

excluded is used, reconditioned, and demonstration equipment; equipment used for prime power in place of utility power and equipment used in

life support applications.

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WI, USA

Effective January 1, 2003 replaces all undated Warranties and all Warranties dated before January 1, 2003

Page is loading ...

Briggs & Stratton 01813-0 User manual

This manual is also suitable for

Briggs & Stratton 01813-0 User manual

in other languages

Related papers

Other documents