G-Shock H-1 Owner's manual

Brand: G-Shock

Model: H-1

Category: Water pumps

Type: Owner's manual

This manual is also suitable for

MO1408-EC

E-1

ENGLISH

Congratulations upon your selection of this CASIO watch.

Applications

The built-in sensors of this watch measure direction, barometric pressure, temperature and altitude.

Measured values are then shown on the display. Such features make this watch useful when hiking,

mountain climbing, or when engaging in other such outdoor activities.

Warning !

• The measurement functions built into this watch are not intended for taking measurements that

require professional or industrial precision. Values produced by this watch should be considered

as reasonable representations only.

•

When engaging in mountain climbing or other activities in which losing your way can create a

dangerous or life-threatening situation, always use a second compass to conﬁ rm direction readings.

• Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss

suffered by you or any third party arising through the use of this product or its malfunction.

E-2

Important!

• Your watch’s Altimeter Mode calculates relative altitude based on changes in barometric pressure

measurement by its pressure sensor. For more information, see page E-36 and E-48.

• Immediately before embarking or otherwise taking altitude readings, be sure to specify a reference

altitude. If you don’t the readings produced by the watch probably will not be very accurate. For more

information, see “To specify a reference altitude value” (page E-44).

E-3

About This Manual

• Depending on the model of your watch, digital display text appears

either as dark ﬁ gures on a light background, or light ﬁ gures on a dark

background. All examples in this manual are shown using dark ﬁ gures

on a light background.

• Button operations are indicated using the letters shown in the

illustration.

• Note that the product illustrations in this manual are intended for

reference only, and so the actual product may appear somewhat

different than depicted by an illustration.

E-4

Things to check before using the watch

1. Check the battery power level.

indicated by the battery power indicator (page E-11)?

Go to step 2.

Power is low.

Charge the watch by placing it in a location

where it is exposed to light. For details, see “Charging the

Watch” (page E-10).

NO YES

YES

Does any one of the following conditions exist?

• Battery power indicator indicates L and LOW is flashing on the

display.

• CHG is flashing on the display.

• The face is blank.

The watch is charged

sufficiently.

For details about

charging, see

“Charging the Watch”

(page E-10).

Battery power

indicator

E-5

2. Check the Home City and the daylight saving time (DST) setting.

Use the procedure under “To conﬁ gure Home City and summer time settings” (page E-31) to conﬁ gure

your Home City and daylight saving time settings.

Important!

• Proper time calibration signal reception, and World Time Mode and Sunrise/Sunset Mode data depend

on correct Home City, time, and date settings in the Timekeeping Mode. Make sure you conﬁ gure

these settings correctly.

3. Set the current time.

• To set the time using a time calibration signal

See “To get ready for a receive operation” (page E-17).

• To set the time manually

See “Conﬁ guring Current Time and Date Settings Manually” (page E-33).

The watch is now ready for use.

• For details about the watch’s radio controlled timekeeping feature, see “Radio Controlled Atomic

Timekeeping” (page E-15).

E-6

Contents

E-3 About This Manual

E-4 Things to check before using the watch

E-10 Charging the Watch

E-14 To recover from the sleep state

E-15 Radio Controlled Atomic Timekeeping

E-17 To get ready for a receive operation

E-19 To perform manual receive

E-22 To check the latest signal reception results

E-22 To turn auto receive on or off

E-24 Mode Reference Guide

E-29 Timekeeping

E-30 Using Date/Time Records

E-31 Conﬁ guring Home City Settings

E-31 To conﬁ gure Home City and summer time settings

E-33 Conﬁ guring Current Time and Date Settings Manually

E-33 To change the current time and date settings manually

E-35 Specifying Temperature, Barometric Pressure, and Altitude Display Units

E-35 To specify temperature, barometric pressure, and altitude display units

E-7

E-36 Using the Altimeter Mode

E-37 To select the altitude screen format

E-37 To select the altitude auto reading interval

E-39 To take altitude readings

E-42 To specify the altitude differential start point

E-43 To use the altitude differential value

E-44 To specify a reference altitude value

E-45 To save a reading manually

E-51 Precautions Concerning Simultaneous Altitude and Temperature Readings

E-52 Taking Direction Readings

E-52 To perform 2-point calibration

E-54 To take a direction reading

E-58 To perform magnetic declination correction

E-61 Taking Barometric Pressure and Temperature Readings

E-61 To take barometric pressure and temperature readings

E-66 To enable or disable the barometric pressure change alert

E-68 To calibrate the pressure sensor and the temperature sensor

E-70 Viewing Memory Records

E-70 To view data in watch memory

E-74 To delete all saved data

E-74 To delete a speciﬁ c record

Operation Guide 3410

E-8

E-75 Checking the Current Time in a Different Time Zone

E-75 To enter the World Time Mode

E-75 To view the time in another time zone

E-76 To specify standard time or daylight saving time (DST) for a city

E-77 Using the Stopwatch

E-77 To enter the Stopwatch Mode

E-77 To perform an elapsed time operation

E-77 To pause at a split time

E-78 To measure two ﬁ nishes

E-79 Using the Countdown Timer

E-79 To enter the Countdown Timer Mode

E-79 To specify the countdown start time

E-80 To perform a countdown timer operation

E-80 To stop the alarm

E-81 Using the Alarm

E-81 To enter the Alarm Mode

E-82 To set an alarm time

E-83 To turn an alarm and the Hourly Time Signal on and off

E-83 To stop the alarm

E-9

E-84 Looking up Sunrise and Sunset Times

E-84 To view sunrise and sunset times

E-85 To view the sunrise/sunset time for a particular date

E-86 To look up the sunrise and sunset times for a speciﬁ c location

E-88 Illumination

E-88 To turn on illumination manually

E-88 To change the illumination duration

E-90 To turn the auto light switch on and off

E-92 Other Settings

E-92 To turn the button operation tone on and off

E-93 To turn Power Saving on or off

E-94 Troubleshooting

E-100 Speciﬁ cations

E-10

Charging the Watch

The face of the watch is a solar panel that generates power from light. The generated power charges a

built-in rechargeable battery, which powers watch operations. The watch charges whenever it is exposed

to light.

Charging Guide

Whenever you are not wearing the

watch, leave it in a location where it

is exposed to light.

• Best charging performance is

achieved by exposing the watch to

the strongest light available.

When wearing the watch, make sure

that its face is not blocked from light

by the sleeve of your clothing.

• The watch may enter a sleep state

(page E-14) if its face is blocked

by your sleeve even only partially.

Warning!

Leaving the watch in bright light for charging can cause it to become quite hot.

Take care when handling the watch to avoid burn injury. The watch can become particularly hot

when exposed to the following conditions for long periods.

• On the dashboard of a car parked in direct sunlight

• Too close to an incandescent lamp

• Under direct sunlight

E-11

Important!

• Allowing the watch to become very hot can cause its liquid crystal display to black out. The

appearance of the LCD should become normal again when the watch returns to a lower temperature.

• Turn on the watch’s Power Saving function (page E-14) and keep it in an area normally exposed to

bright light when storing it for long periods. This helps to ensure that power does not run down.

• Storing the watch for long periods in an area where there is no light or wearing it in such a way that it is

blocked from exposure to light can cause power to run down. Expose the watch to bright light

whenever possible.

Power Levels

You can get an idea of the watch’s power level by observing the battery power indicator on the display.

Important!

• If low battery power is indicated, expose the face of the watch to direct light to charge. At Level 5, the

battery is dead, which causes watch functions to stop, all data in watch memory to be deleted, and all

watch settings to return to their initial factory defaults.

Level Battery Power Indicator Function Status

(H)

All functions enabled.

(M)

All functions enabled.

Battery power

indicator

Battery power

indicator

E-12

Level Battery Power Indicator Function Status

(L)

Auto and manual receive, illumination,

beeper, and sensor operation disabled.

(CHG)

Except for the

CHG

(charge) indicator, all

functions and display indicators disabled.

5 – – – All functions disabled.

• The ﬂ ashing

LOW

indicator at Level 3 (L) tells you that battery power is very low, and that exposure to

bright light for charging is required as soon as possible.

• Display indicators reappear as soon as the battery is charged from Level 5 to Level 2 (M).

• Leaving the watch exposed to direct sunlight or some other very strong light source can cause the

battery power indicator to show a reading temporarily that is higher than the actual battery level. The

correct battery level should be indicated after a few minutes.

E-13

Power Recovery Mode

• Performing multiple sensor, illumination, or beeper operations during a short period may cause all of

the battery power indicators (H, M, and L) to start ﬂ ashing on the display. This indicates that the watch

is in the power recovery mode. Illumination, alarm, countdown timer alarm, hourly time signal, and

sensor operations will be disabled until battery power recovers.

• Battery power will recover in about 15 minutes. At this time, the battery power indicators (H, M, L) will

stop ﬂ ashing. This indicates that the functions listed above are enabled again.

• If all of the battery power indicators (H, M, L) are ﬂ ashing and the

CHG

(charge) indicator also is

ﬂ ashing, it means the battery level is very low. Expose the watch to bright light as soon as possible.

• Even if battery power is at Level 1 (H) or Level 2 (M), the Digital Compass Mode, Barometer/

Thermometer Mode, or Altimeter Mode sensor may be disabled if there is not enough voltage available

to power it sufﬁ ciently. This is indicated when all of the battery power indicators (H, M, L) are ﬂ ashing.

• Frequent ﬂ ashing of all of the battery power indicators (H, M, L) probably means that remaining battery

power is low. Leave the watch in bright light to allow it to charge.

Charging Times

Exposure Level (Brightness)

Daily

Operation

Level Change *2

Level 5 Level 4 Level 3 Level 2 Level 1

Outdoor sunlight (50,000 lux) 5 min. 2 hours 16 hours 5 hours

Sunlight through a window (10,000 lux)

24 min. 7 hours 79 hours 22 hours

Daylight through a window on a

cloudy day (5,000 lux)

48 min. 12 hours 160 hours 43 hours

Indoor ﬂ uorescent lighting (500 lux) 8 hours 175 hours – – – – – –

E-14

*1 Approximate amount of exposure time required each day to generate enough power for normal daily

operation.

*2 Approximate amount of exposure time (in hours) required to take power from one level to the next.

• The above exposure times all are for reference only. Actual exposure times depend on lighting

conditions.

• For details about the operating time and daily operating conditions, see the “Power Supply” section of

the Speciﬁ cations (page E-103).

Power Saving

When turned on, Power Saving enters a sleep state automatically whenever the watch is left for a certain

period in an area where it is dark. The table below shows how watch functions are affected by Power

Saving.

• For information about enabling and disabling power saving, see “To turn Power Saving on or off” (page

E-93).

• There actually are two sleep state levels: “display sleep” and “function sleep”.

Elapsed Time in Dark Display Operation

60 to 70 minutes (display sleep) Blank, with

ﬂ ashing Display is off, but all functions are enabled.

6 or 7 days (function sleep) Blank, with

not ﬂ ashing

All functions are disabled, but timekeeping is

maintained.

• The watch will not enter a sleep state between 6:00 AM and 9:59 PM. If the watch is already in a sleep

state when 6:00 AM arrives, however, it will remain in the sleep state.

• Power Saving is enabled only when the watch is in the Timekeeping Mode with the Day of the Week

screen displayed (page E-29) or in the World Time Mode (page E-75).

To recover from the sleep state

Move the watch to a well-lit area, press any button, or angle the watch towards your face for reading (page E-89).

E-15

Radio Controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting accordingly. However, when

using the watch outside of areas covered by time calibration signals, you will have to adjust the settings

manually as required. See “Conﬁ guring Current Time and Date Settings Manually” (page E-33) for more

information.

This section explains how the watch updates its time settings when the city code selected as the Home

City is in Japan, North America, Europe, or China, and is one that supports time calibration signal

reception.

If your Home City Code setting is this:

The watch can receive the signal from the transmitter

located here:

LIS, LON, MAD, PAR, ROM, BER, STO, ATH, MOW Anthorn (England), Mainﬂ ingen (Germany)

HKG, BJS Shangqiu City (China)

TPE, SEL, TYO Fukushima (Japan), Fukuoka/Saga (Japan)

HNL, ANC, YVR, LAX, YEA, DEN, MEX, CHI, NYC, YHZ,

YYT

Fort Collins, Colorado (United States)

Important!

• The areas covered by

MOW

HNL

and

ANC

are quite far from the calibration signal transmitters, so

certain conditions may cause reception problems.

• When

HKG

BJS

is selected as the Home City, only the time and date are adjusted according to the

time calibration signal. You need to switch manually between standard time and daylight saving time

(DST) if required. See “To conﬁ gure Home City and summer time settings” (page E-31) for information

about how to do this.

Operation Guide 3410

E-16

Approximate Reception Ranges

UK and German Signals

Anthorn

500 kilometers

1,500 kilometers

The Anthorn signal is

receivable within this area

Mainflingen

North American Signal

Japanese Signals Chinese Signal

500 kilometers

Changchun

Beijing

Shangqiu

Shanghai

Chengdu

Hong Kong

1,500 kilometers

2,000 miles

(3,000 kilometers)

600 miles

(1,000 kilometers)

Fort Collins

1,000 kilometers

Signals are receivable in the Taiwan area

when reception conditions are

ood.

For the Honolulu and Anchorage time zones, the

signal can be received when reception conditions

are favorable.

Fukuoka/Saga

500 kilometers

Fukushima

E-17

• Even when the watch is within range of a transmitter, signal reception may be impossible due to the

effects of geographic contours, structures, weather, the time of year, the time of day, radio interference,

etc. The signal becomes weaker at distances of approximately 500 kilometers, which means that the

inﬂ uence of the conditions listed above becomes even greater.

• Signal reception may not be possible at the distances noted below during certain times of the year or

day. Radio interference may also cause problems with reception.

Mainﬂ ingen (Germany) or Anthorn (England) transmitters: 500 kilometers (310 miles)

Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)

Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)

Shangqiu (China) transmitter: 500 kilometers (310 miles)

• As of December 2012, China does not use Daylight Saving Time (DST). If China does go to the Daylight

Saving Time system in the future, some functions of this watch may no longer operate correctly.

To get ready for a receive operation

1. Conﬁ rm that the watch is in the Timekeeping Mode or World Time Mode. If it isn’t, use

to enter the

Timekeeping Mode or World Time Mode (page E-26).

2. The antenna of this watch is located on its 12 o’clock side. Position the watch with 12 o’clock facing

towards a window as shown in the nearby illustration. Make sure there are no metal objects nearby.

• Signal reception normally is better at night.

• The receive operation takes from two to ten minutes, but

in some cases it can take as long as 20 minutes. Take

care that you do not perform any button operation or

move the watch during this time.

12 o’clock

E-18

• Signal reception may be difﬁ cult or even impossible under the conditions described below.

Inside or

among

buildings

Inside a

vehicle

Near

household

appliances,

ofﬁ ce

equipment,

or a mobile

phone

Near a

construction

site, airport

Near

high-tension

power lines

Among or

behind

mountains

3. What you should do next depends on whether you are using auto receive or manual receive.

• Auto receive: Leave the watch over night in the location you selected in step 2. See “Auto Receive”

below for details.

• Manual receive: Perform the operation under “To perform manual receive” on page E-19.

Auto Receive

• With auto receive, the watch performs the receive operation each day automatically up to six times (up

to ﬁ ve times for the Chinese calibration signal) between the hours of midnight and 5 a.m. (according to

the Timekeeping Mode time). When any receive operation is successful, none of the other receive

operations for that day are performed.

• When a calibration time is reached, the watch will perform the receive operation only if it is in the

Timekeeping Mode or World Time Mode. The receive operation is not performed if a calibration time is

reached while you are conﬁ guring settings.

E-19

• You can use the procedure under “To turn auto receive on and off” (page E-22) to enable or disable

auto receive.

To perform manual receive

1. Use

to select the Receive Mode (

R/C

) as shown on page E-26.

2. Hold down

until

RC Hold

appears on the display and then

disappears.

• A signal level indicator (L1, L2, or L3, see page E-21) will appear

on the display after reception starts. Do not allow the watch to

move and do not perform any button operation until GET or ERR

appears on the display.

• If the receive operation is successful, the reception date and time

appear on the display, along with the GET indicator.

The watch will return to the Timekeeping Mode if you press

if you do not perform any button operation for about two or three

minutes.

Receiving

Receiving indicator

Receive successful

Receiving

Receiving indicator

Receive successful

E-20

• If the current reception fails but a previous reception (within the

last 24 hours) was successful, the display shows the receiving

indicator and the ERR indicator. If the ERR indicator only is

displayed (without the receiving indicator), it means that all of the

receive operations over the past 24 hours have failed.

The watch will return to the Timekeeping Mode without changing

the time setting if you press

or if you do not perform any button

operation for about two or three minutes.

Note

• You can interrupt a time calibration signal reception operation by

pressing any button.

Receive failed

If there was a previously

successful reception

Receive failed

If there was a previously

successful reception

E-21

Signal Level Indicator

During manual receive, the signal level indicator displays the signal level

as shown below.

Weak (Unstable) Strong (Stable)

The level indication will change in accordance with reception conditions

while reception is being performed.

As you watch the indicator, keep the watch in a location that best

maintains stable reception.

• Even under optimum reception conditions, it can take about 10

seconds for reception to stabilize.

• Note that weather, the time of day, surroundings, and other factors all

can affect reception.

E-22

To check the latest signal reception results

Enter the Receive Mode (page E-26).

• When receive is successful, the display shows the time and date that

receive was successful.

- : - -

indicates that none of the reception

operations were successful.

• To return to the Timekeeping Mode, press

To turn auto receive on or off

1. Enter the Receive Mode (page E-26).

2. Hold down

for at least two seconds. Release

after

AUTO

appears. This is the setting screen.

• Note that the setting screen will not appear if the currently selected

Home City is one that does not support time calibration reception.

3. Press

to toggle auto receive between on (

) and off (

OFF

4. Press

to exit the setting screen.

On/Off statusOn/Off status

E-23

Radio-controlled Atomic Timekeeping Precautions

• Strong electrostatic charge can result in the wrong time setting.

• Even if a receive operation is successful, certain conditions can cause the time setting to be off by up

to one second.

• The watch is designed to update the date and day of the week automatically for the period January 1,

2000 to December 31, 2099. Updating of the date by signal reception will no longer be performed

starting from January 1, 2100.

• If you are in an area where signal reception is not possible, the watch keeps time with the precision

noted in “Speciﬁ cations”.

• The receive operation is disabled under any of the following conditions.

– While power is at Level 3 (L) or lower (page E-11)

– While the watch is in the power recovery mode (page E-13)

– While a direction, barometric pressure/temperature, or altitude reading operation is in progress

– When the watch is in the function sleep state (“Power Saving”, page E-14)

– While the barometric pressure change indicator is displayed

– While a countdown timer operation is in progress (page E-79)

• A receive operation is cancelled if an alarm sounds while it is being performed.

• The Home City setting reverts to the initial default of

TYO

(Tokyo) whenever the battery power level

drops to Level 5 or when you have the rechargeable battery replaced. If this happens, change the

Home City to the setting you want (page E-31) .

Operation Guide 3410

E-24

Mode Reference Guide

Your watch has 11 “modes”. The mode you should select depends on what you want to do.

To do this: Enter this mode: See:

• View the current date in the Home City

• Conﬁ gure Home City and daylight saving time (DST) settings

• Conﬁ gure time and date settings manually

• Record the current date and time

Timekeeping Mode E-29

• View the altitude at your current location

• Determine the altitude differential between two locations (reference

point and current location)

•

Record the current altitude reading along with the reading date and time

Altimeter Mode E-36

• Determine your current bearing or the direction from your current

location to a destination

•

Record the current direction reading along with the reading date and time

Digital Compass Mode E-52

• View the barometric pressure and temperature at your current location

• View a graph of barometric pressure readings

• View barometric pressure tendency information

• Record the current barometric pressure and readings along with the

reading date and time

Barometer/Thermometer

Mode

E-61

View the current time in one of 48 cities (31 time zones) around the globe World Time Mode E-75

Use the stopwatch to measure elapsed time Stopwatch Mode E-77

Use the countdown timer Countdown Timer Mode E-79

Set an alarm time Alarm Mode E-81

E-25

To do this: Enter this mode: See:

View the sunrise and sunset times for a speciﬁ c date Sunrise/Sunset Mode E-84

• Recall time, direction reading, barometric pressure/temperature

reading, and altitude reading data

Data Recall Mode E-70

• Perform a manual time calibration signal receive operation

• Check whether the last receive operation was successful

• Conﬁ gure auto receive settings

Receive Mode E-19

E-26

Selecting a Mode

• The illustration below shows which buttons you need to press to navigate between modes.

• To return to the Timekeeping Mode from any other mode, hold down

for about two seconds.

• In the Timekeeping Mode, press

to enter the Stopwatch Mode (page E-77).

Countdown

Timer Mode

Alarm Mode

Stopwatch Mode

World Time

Mode

Receive Mode

Timekeeping Mode

Sunrise/Sunset

Mode

Data Recall

Mode

Countdown

Timer Mode

Alarm Mode

Stopwatch Mode

World Time

Mode

Receive Mode

Timekeeping Mode

Sunrise/Sunset

Mode

Data Recall

Mode

E-27

Sensor Modes

Altimeter Mode

Barometer/

Thermometer Mode

Digital Compass Mode

Sensor Modes

Altimeter Mode

Barometer/

Thermometer Mode

Digital Compass Mode

• This watch has three “sensor modes”: Altimeter Mode, Digital Compass Mode, and Barometer/

Thermometer Mode. Press the

button to display a sensor mode screen.

• The sensor mode that was displayed when you last returned to the Timekeeping Mode will appear ﬁ rst.

E-28

General Functions (All Modes)

The functions and operations described in this section can be used in all of the modes.

Auto Return Features

• The watch will automatically return to the Timekeeping Mode if you do not perform any button operation

for a particular amount of time in each mode.

Mode Name Approximate Elapsed Time

Sunrise/Sunset, Data Recall, Alarm, Receive, Digital

Compass

3 minutes

Altimeter 1 hour minimum

12 hours maximum

Barometer/Thermometer 1 hour

Setting screen (digital setting ﬂ ashing) 3 minutes

• If you leave a screen with ﬂ ashing digits on the display for two or three minutes without performing any

operation, the watch exits the setting screen automatically.

Initial Screens

When you enter the Data Recall, Alarm, World Time, or Digital Compass Mode, the data you were viewing

when you last exited the mode appears ﬁ rst.

Scrolling

The

and

buttons are used on the setting screen to scroll through data on the display. In most

cases, holding down these buttons during a scroll operation scrolls through the data at high speed.

E-29

Timekeeping

Use the Timekeeping Mode (

TIME

) to set and view the current time and date.

• Each press of

in the Timekeeping Mode will change screen contents as shown below.

Day of the Week Screen Barometric Pressure

Graph Screen

Barometric pressure graph

Day of week

Seconds

Hour :

Minutes

Month - Day

indicator

Graphic (seconds)*

* The graphic appears as the pattern shown below when a stopwatch elapsed time

operation is in progress or paused (page E-77).

E-30

Using Date/Time Records

You can use the procedure in this section to create a date/time record of the current date (month, day,

year) and time (minute second). You can later recall a record to view it.

Important!

• The watch has memory for storage of up to 40 records of various types. If you perform an operation

that creates a new record while there are already 40 records in memory, the oldest record is deleted

automatically to make room for the new one (page E-70).

1. In the Timekeeping Mode, hold down

until the watch beeps (about 0.5 seconds).

• REC will appear on the display, indicating that a record of the current date and time was created.

After about one second, the watch will return to the Timekeeping Mode screen.

2. To view a record, enter the Data Recall Mode (page E-26) and use the

and

buttons to scroll. See

“Viewing Memory Records” (page E-70) for more information.

E-31

Conﬁ guring Home City Settings

There are two Home City settings: actually selecting the Home City and selecting either standard time or

daylight saving time (DST).

To conﬁ gure Home City and summer time settings

1. In the Timekeeping Mode, hold down

for at least two seconds.

SET

and

Hold

will appear on the display ﬁ rst, and then

Hold

will

disappear. Release

after

Hold

disappears.

• The watch will exit the setting mode automatically if you do not

perform any operation for about two or three minutes.

• For details about city codes, see the “City Code Table” at the back

of this manual.

2. Use

(East) and

(West) to scroll through the available city codes.

• Keep scrolling until the city code you want to select as your Home

City is displayed.

3. Press

to display the DST setting screen.

Use

to cycle through the DST settings in the sequence shown below.

Auto DST (AUTO) DST off (OFF)

DST on (

)

City code

DST indicator

City code

DST indicator

Operation Guide 3410

E-32

• The Auto DST (AUTO) setting will be available only when a city code that supports time calibration

signal reception (page E-15) is selected as the Home City. While Auto DST is selected the DST

setting will be changed automatically in accordance with time calibration signal data.

• Note that you cannot switch between standard time and daylight saving time (DST) while UTC is

selected as your Home City.

5. After all of the settings are the way you want, press

twice to exit the setting screen.

• Daylight Saving Time is turned on when the DST indicator is on the display.

Note

• After you specify a city code, the watch will use UTC* offsets in the World Time Mode to calculate

the current time for other time zones based on the current time in your Home City.

* Coordinated Universal Time, the world-wide scientiﬁ c standard of timekeeping.

The reference point for UTC is Greenwich, England.

• Selecting some city codes automatically makes it possible for the watch to receive the time

calibration signal for the corresponding area. See page E-15 for details.

E-33

Conﬁ guring Current Time and Date Settings Manually

You can conﬁ gure current time and date settings manually when the watch is unable to receive a time

calibration signal.

Important!

• Before conﬁ guring current time and date settings, be sure set your Home City (page E-31).

To change the current time and date settings manually

1. In the Timekeeping Mode, hold down

for at least two seconds.

SET

and

Hold

will appear on the display ﬁ rst, and then

Hold

will

disappear. Release

after

Hold

disappears.

2. Press

to move the ﬂ ashing in the sequence shown below to select

the other settings.

Thermometer/Barometer/

Altitude display unit

(page E-35)

Power

Saving

(page E-93)

Illumination

Duration

(page E-88)

Button Operation

Tone

(page E-92)

Day

Month

City Code

(page E-31)

DST

(page E-31)

12/24-Hour

Format

Seconds Hour Minutes Year

City codeCity code

E-34

3. When the timekeeping setting you want to change is ﬂ ashing, use

and/or

to change it as

described below.

Screen To do this: Do this:

Toggle between 12-hour (

12H

) and 24-hour (

24H

)

timekeeping.

Press

Reset the seconds to

(If the current seconds count is between 30 and 59,

one is added to the minute count).

Press

Change the hour or minutes

Use

(+) and

(–).

Change the year, month, or day

4. After all of the settings are the way you want, press

twice to exit the setting screen.

Note

• While the 12-hour format is selected for timekeeping, a P (PM) indicator will appear for times from

noon to 11:59 p.m. No indicator appears for times from midnight to 11:59 a.m. With 24-hour format,

time is displayed from 0:00 to 23:59, without any P (PM) indicator.

• The watch’s built-in full automatic calendar makes allowances for different month lengths and leap

years. Once you set the date, there should be no reason to change it except after you have the

watch’s rechargeable battery replaced or after power drops to Level 5 (page E-11).

• The day of the week changes automatically when the date changes.

E-35

Specifying Temperature, Barometric Pressure, and Altitude Display Units

Use the procedure below to specify the temperature, barometric pressure, and altitude display units to be

used in the Barometer/Thermometer Mode and the Altimeter Mode.

Important!

• When

TYO

(Tokyo) is selected as the Home City, the altitude unit is set

automatically to meters (

), the barometric pressure unit to

hectopascals (

hPa

), and the temperature unit to Celsius (

°C

). These

settings cannot be changed.

To specify temperature, barometric pressure, and altitude display

units

1. In the Timekeeping Mode, hold down

for at least two seconds.

SET

and

Hold

will appear on the display ﬁ rst, and then

Hold

will

disappear. Release

after

Hold

disappears.

2. Press

as many times as necessary until

UNIT

appears on the display (page E-33).

3. Perform the operations below to specify the display units you want.

To specify this unit: Press this key: To toggle between these settings:

Altitude

(meters) and

(feet)

Barometric Pressure

hPa

(hectopascals) and

inHg

(inches of mercury)

Temperature

°C

(Celsius) and

°F

(Fahrenheit)

4. After all of the settings are the way you want, press

twice to exit the setting screen.

E-36

Using the Altimeter Mode

The watch takes altitude readings and displays results based on air pressure measurements taken by a

built-in pressure sensor. It also saves various types of altitude records and data.

Getting Ready

Before actually taking an altitude reading you need to select an altitude screen format and select an

altitude reading interval.

Selecting the Altitude Screen Format

You can select either of two screen formats for the Altimeter Mode.

Screen 1

Altitude

Tendency Graph

Altitude

Current time

Screen 2

Relative altitude

Altitude

Current time

• Altitude tendency graph contents are updated each time you take an altitude reading.

• To take readings of the difference between the altitude at your current location and the altitude at a

reference point, select Screen 2. See “Using an Altitude Differential Value” (page E-42) for more

information.

E-37

To select the altitude screen format

1. Enter the Altimeter Mode (page E-27).

2. Use

to toggle the setting between the two screens.

Selecting the Altitude Auto Reading Interval

You can select either of the following two altitude auto reading intervals.

0’05

: Readings at one-second intervals for the ﬁ rst three minutes, and then every ﬁ ve seconds for

approximately the next hour

2’00

: Readings at one-second intervals for the ﬁ rst three minutes, and then every two minutes for

approximately the next 12 hours

Note

• If you do not perform any button operation while in the Altimeter Mode, the watch will return to the

Timekeeping Mode automatically after 12 hours (altitude auto reading interval: 2’00) or after one

hour (altitude auto reading interval: 0’05).

To select the altitude auto reading interval

1. In the Altimeter Mode, hold down

for at least two seconds. You can

release

after

ALTI

appears.

• The current altitude reading value will appear at this time.

2. Press

to display the current altitude auto reading interval setting.

• The display will show

0’05

2’00

3. Press

to toggle the altitude auto reading interval setting between

0’05

and

2’00

4. Press

to exit the setting screen.

E-38

Taking Altitude Readings

Use the procedure below to take basic altitude readings.

• See “Using Reference Altitude Values” (page E-44) for information about how to make altimeter

readings more accurate.

• See “How does the altimeter work?” (page E-48) for information about how the watch measures altitude.

E-39

To take altitude readings

Enter the Altimeter Mode (page E-27).

• This will automatically start an altitude reading operation, and the result

will appear on the display as a value in 1-meter (5-foot) units.

• Readings will continue to be taken about every second for the ﬁ rst

three minutes. For information about the reading interval after that, see

page E-37.

• You can restart the reading operation from the beginning at any time

by pressing

Note

• After you are ﬁ nished, press

to return to the Timekeeping Mode and

stop auto altimeter readings.

• The watch will return to the Timekeeping Mode automatically if you do

not perform any operation (page E-28).

• The measurement range for altitude is –700 to 10,000 meters (–2,300

to 32,800 feet).

• The displayed altitude value changes to

- - - -

if an altitude reading

falls outside the measurement range. An altitude value will reappear as

soon as the altitude reading is within the allowable range.

• Normally, displayed altitude values are based on the watch’s preset

conversion values. You also can specify a reference altitude value, if

you want. See “Using Reference Altitude Values” (page E-44).

• You can change the unit for displayed altitude values to either meters

(m) or feet (ft). See “To specify temperature, barometric pressure, and

altitude display units” (page E-35).

Screen 1 Selected

Altitude

Tendency

Graph

Altitude

Differential

Graph

Altitude

Current

time

Screen 1 Selected

Altitude

Tendency

Graph

Altitude

Differential

Graph

Altitude

Current

time

Screen 2 Selected

Relative

altitude

Altitude

Differential

Graph

Altitude

Current

time

Screen 2 Selected

Relative

altitude

Altitude

Differential

Graph

Altitude

Current

time

Operation Guide 3410

E-40

Checking the Latest Changes in Altitude

• The altitude differential graph shows the difference between the currently displayed altitude reading

and the previous reading during while readings are being taken automatically.

–30m

+30m

+10m +20m

+18m

31 meters or greater

–4m

–10m –20m

difference

Example

E-41

• The altitude tendency graph shows changes in altitude over the past 20 readings while readings are

being taken automatically.

80 meters

(10 meters for

each block )

20 readings

ago

10 readings

ago

Current

reading

Advanced Altimeter Mode Operations

Use the information in this section to obtain more accurate altimeter readings, especially while mountain

climbing or trekking.

E-42

Using an Altitude Differential Value

The Altimeter Mode screen has an altitude differential value that shows

the change in altitude from a reference point you specify. The altitude

differential value is updated each time the watch takes an altitude reading.

• The range of the altitude differential value is –3,000 meters (–9,995

feet) to 3,000 meters (9,995 feet).

•

- - - -

is displayed in place of the altitude differential value whenever

the measured value is outside the allowable range.

• See “Using the Altitude Differential Value While Mountain Climbing or

Hiking” (page E-43) for some real-life examples of how to use this

feature.

To specify the altitude differential start point

1. In the Altimeter Mode, select Screen 2 as the Altimeter Mode display

(page E-37).

2. Press

• The watch will take an altitude reading and register the result as

the altitude differential value start point. The altitude differential

value will be reset to zero at this time.

Altitude differentialAltitude differential

E-43

Using the Altitude Differential Value While Mountain Climbing or Hiking

After you specify the altitude differential start point while mountain climbing or hiking, you can easily

measure the change in the altitude between that point and other points along the way.

To use the altitude differential value

1. In the Altimeter Mode, check to make sure that an altitude reading is

on the display.

• If an altitude reading is not displayed, press

to take one. See “To

take altitude readings” (page E-39) for details.

2. Use the contour lines on your map to determine the difference in

altitude between your current location and your destination.

3. In the Altimeter Mode, press

to specify your current location as the

altitude differential start point.

• The watch will take an altitude reading and register the result as

the altitude differential value start point. The altitude differential

value will be reset to zero at this time.

4. While comparing the altitude difference you determined on the map

and the watch’s altitude differential value, advance towards your

destination.

• If the map shows that the difference in altitude between your

location and your destination is +80 meters for example, you know

you will be nearing your destination when the displayed altitude

differential value shows +80 meters.

Current

location

Destination

altitude

Current

location

Destination

altitude

Altitude

differential

Altitude

differential

E-44

Using Reference Altitude Values

To minimize the chance of reading error, you should update the reference altitude value before setting off

on a trek or any other activity where you plan to take altitude readings. During a trek, keep checking the

readings produced by the watch against altitude information provided by markers and other information,

and update the reference altitude value as required.

• Reading error can be caused by changes in barometric pressure, atmospheric conditions, and

elevation.

• Before performing the procedure below, look up the altitude of your current location on a map, the

Internet, etc.

To specify a reference altitude value

1. In the Altimeter Mode, hold down

for at least two seconds. You can

release

after

ALTI

appears.

• The current altitude reading value will appear at this time.

2. Use

(+) or

(–) to change the current reference altitude value in

1-meter (5-foot) increments.

• Change the reference altitude value to an accurate altitude reading

that you get from a map or other source.

• You can set the reference altitude value within the range of –10,000

to 10,000 meters (–32,800 to 32,800 feet).

• Pressing

and

at the same time returns to OFF (no reference

altitude value), so the watch performs air pressure to altitude

conversions based on preset data only.

3. Press

to exit the setting screen.

E-45

Types of Altitude Data

Your watch stores two types of altitude data: altitude records and historical altitude values.

Manually Saved Records

Each altitude reading you take manually is stored along with the date and time of the reading as an

“altitude record”. You can later recall an altitude record to view it.

Important!

• The watch has memory for storage of up to 40 records of various types. If you perform an operation

that creates a new record while there are already 40 records in memory, the oldest record is deleted

automatically to make room for the new one (page E-70). Note that altitude differential graph and

altitude tendency graph information is not stored as part of an altitude record.

To save a reading manually

1. In the Altimeter Mode, hold

for at least two seconds.

•

REC

and

Hold

will appear on the display ﬁ rst, and then

Hold

will

disappear. Release

after

Hold

disappears.

• The watch will create a record of the current altitude reading along

with the date and time, and then return automatically to the altitude

reading screen.

2. To view a record, enter the Data Recall Mode (page E-26) and use the

and

buttons to scroll. See “Viewing Memory Records” (page

E-70) for more information.

E-46

Auto Save Values

The watch automatically keeps track of the four types of values below, and updates them as required

along with the time and date of the reading.

High Altitude (MAX)

Low Altitude (MIN)

Cumulative Ascent (ASC)

Cumulative Descent (DSC)

• For detailed information about each value, see page E-47.

• For information about viewing these values, see “Viewing Memory Records” (page E-70).

• These values are checked and updated automatically by the watch as altitude auto measurements are

taken. You can change the auto save interval, if you want (page E-37).

• Auto save is performed only while the watch is in the Altimeter Mode.

E-47

How Cumulative Ascent and Cumulative Descent Values Are Updated

Session start point

20 m

0 m

120 m

320 m

620 m

Session end point

The total ascent and total descent values produced by an Altimeter Mode reading operation session

during the example climb illustrated above are calculated as follows.

Total Ascent:

(300 m) +

(620 m) = 920 m

Total Descent:

(320 m) +

(500 m) = 820 m

• Cumulative ascent and cumulative descent values are updated whenever there is a difference of at

least ±15 meters (±49 feet) from one reading to the next.

•

ASC

and

DSC

values are retained in memory without being reset even if you exit the Altimeter Mode.

When you re-enter the Altimeter Mode, accumulation resumes from the value where it last stopped. See

page E-74 for information about how to reset the

ASC

and

DSC

values to zero.

Operation Guide 3410

E-48

How does the altimeter work?

Generally, air pressure decrease as altitude increases. This watch bases its altitude reading on

International Standard Atmosphere (ISA) values stipulated by the International Civil Aviation Organization

(ICAO). These values deﬁ ne relationships between altitude and air pressure.

0 m

500 m

1000 m

1500 m

2000 m

2500 m

3000 m

3500 m

4000 m

899 hPa

795 hPa

701 hPa

616 hPa

1013 hPa

About 8 hPa per 100 m

About 9 hPa per 100 m

About 10 hPa per 100 m

About 11 hPa per 100 m

About 12 hPa per 100 m

Altitude Air Pressure

0 ft.

2000 ft.

4000 ft.

6000 ft.

8000 ft.

10000 ft.

12000 ft.

14000 ft.

25.84 inHg

22.23 inHg

19.03 inHg

29.92 inHg

About 0.15 inHg per 200 ft.

About 0.17 inHg per 200 ft.

About 0.192 inHg per 200 ft.

About 0.21 inHg per 200 ft.

Source: International Civil Aviation Organization

E-49

• Note that the following conditions will prevent you from obtaining accurate readings:

When air pressure changes because of changes in the weather

Extreme temperature changes

When the watch itself is subjected to strong impact

There are two standard methods of expressing altitude: absolute altitude, which expresses an absolute

height above sea level, and relative altitude, which expresses the difference between the altitudes of two

different places. This watch expresses altitudes as relative altitude.

Height of building 130 m

(relative altitude)

Rooftop at an altitude of

230 m above sea level

(absolute altitude)

Sea Level

How the Altimeter Measures Altitude

The altimeter can measure altitude based on its own preset values (initial default method) or using a

reference altitude speciﬁ ed by you.

E-50

When you measure altitude based on preset values

Data produced by the watch’s barometric pressure sensor is converted to approximate altitude based on

ISA (International Standard Atmosphere) conversion values stored in watch memory.

When you measure altitude using a reference altitude speciﬁ ed by you

After you specify a reference altitude, the watch uses that value to convert

barometric pressure readings to altitude (page E-44).

• When mountain climbing, you can specify a reference altitude value in

accordance with a marker along the way or altitude information from a

map. After that, the altitude readings produced by the watch will be more

accurate than they would without a reference altitude value.

Altimeter Precautions

• This watch estimates altitude based on air pressure. This means that altitude readings for the same

location may vary if air pressure changes.

• Do not rely upon this watch for altitude reading or perform button operations while sky diving, hang

gliding, or paragliding, while riding a gyrocopter, glider, or any other aircraft, or while engaging in any

other activity where there is the chance of sudden altitude changes.

• Do not use this watch for measuring altitude in applications that demand professional or industrial level

precision.

• Remember that the air inside of a commercial aircraft is pressurized. Because of this, the readings

produced by this watch will not match the altitude readings announced or indicated by the ﬂ ight crew.

400

E-51

Precautions Concerning Simultaneous Altitude and Temperature Readings

For the more accurate altitude readings, leaving the watch on your wrist is recommended in order to

maintain the watch at a constant temperature.

• When taking temperature readings, keep the watch at as stable a temperature as possible. Changes in

temperature can affect temperature readings. See product speciﬁ cations (page E-100) for sensor

accuracy information.

E-52

Taking Direction Readings

You can use the watch to take direction readings to determine a direction (north, south, east, west) or to

ﬁ nd out your bearing to a destination.

• For information about what you can do to ensure direction readings are accurate, see “Magnetic

Declination Correction” (page E-58) and “Digital Compass Precautions” (page E-59).

Correcting Direction Reading Error (2-point Calibration)

Use 2-point calibration to correct for measurement error due to local magnetism or other causes.

Important!

• Keep the watch level during the calibration process.

• Keep the watch away from electrical household appliances and ofﬁ ce equipment, cellphones, and

other sources of strong magnetism during calibration. Such items can make proper calibration

impossible.

To perform 2-point calibration

1. Enter the Digital Compass Mode (page E-27).

2. Hold down

for at least two seconds. Release the button when

-1-

appears on the display.

E-53

3. Press

• This starts calibration of point 1. After calibration of point 1 is

complete, TURN 180° appears on the display, followed by -2-.

• If ERR appears on the display, press

and then perform calibration of point 1 again.

4. Rotate the watch as precisely as possible 180 degrees from point 1.

5. Press

• This starts calibration of point 2. OK appears on the display after calibration is complete. After one

second, the watch will return to the direction reading screen.

• If ERR appears on the display, perform the procedure from step 3 again.

E-54

To take a direction reading

Important!

• To ensure accuracy, be sure to perform 2-point calibration under actual measurement conditions

before taking direction readings.

1. Enter the Digital Compass Mode (page E-27).

• The watch will automatically start taking direction readings. Readings will be taken and the display

will be updated every second for about 60 seconds. At this point you can check the direction (north,

south, east west) reading.

North

East

South

West

E-55

2. During the approximately 60 seconds that the above reading operation is in progress, point 12 o'clock

on the watch in the direction of the bearing you want to read.

• About one second later, the direction and bearing to your objective will appear on the display.

• If 60 seconds elapse before you can take a bearing reading, press

to restart the direction

reading operation.

315°

0°

Objective Bearing Indication

Meaning

N: North

E: East

W: West

S: South

Bearing to Objective:

Northwest

Bearing Angle

to Objective

Note

• The north indicated by the watch is magnetic north (page E-59).

If you want to display true north, see “Magnetic Declination Correction” (page E-58).

• If only north is indicated on the display (without south, east, or west), it means that bearing

memory contents are displayed. Press

to clear bearing memory contents (page E-56).

• You can return to the Timekeeping Mode by pressing

any time a reading operation is in

progress or stopped.

Operation Guide 3410

E-56

Example: Positioning a map in accordance with actual surroundings (setting a map)

You can align a map with the northerly direction indicated by the watch, and then compare what is shown

on the map with your actual surroundings. This is helpful for checking your current location and the

location of your objective. This process is called “setting a map”.

Saving a Bearing (Bearing Memory)

You can save the bearing to a particular destination in bearing memory and use it to ensure you are

headed in the correct direction.

1. While the direction and bearing to your objective (page E-54) are displayed, press

• This saves the objective information in bearing memory, and displays it as shown below. Now,

any time you are in the Digital Compass Mode, you can check the objective information currently

stored in bearing memory.

Bearing to Objective

Bearing Angle to

Objective

North

2. To return to direction (north, south, east, west) indication, press

to delete bearing memory contents.

Example: Advancing to an objective while monitoring your bearing

Even if you lose sight of your objective, you can use a map to store the required bearing in bearing

memory and refer to the memorized information to advance to your objective.

E-57

1. Set the map (page E-56).

2. Place the watch on the map at your current location, and point 12 o’clock at your desired objective on

the map.

3. Press

to store the direction to your objective in bearing memory. Now you can advance towards

your objective while observing the stored direction on the watch display.

Important!

• As you progress, the direction to your bearing will change, so you need to keep updating the

information in bearing memory.

Using Bearing Records

You can use the procedure in this section to create a bearing record of your current bearing reading, along

with the date and time of the reading. You can later recall a record to view it.

Important!

• The watch has memory for storage of up to 40 records of various types. If you perform an operation

that creates a new record while there are already 40 records in memory, the oldest record is deleted

automatically to make room for the new one (page E-70).

1. Take a bearing reading to your objective so it is shown on the display.

2. Without moving the watch, hold down

for at least two seconds.

• REC and Hold will appear on the display ﬁ rst, and then Hold will disappear. Release

after Hold

disappears.

• The watch will create a record of the current bearing to your objective along with the date and

time, and then return automatically to the direction reading screen.

3. To view a record, enter the Data Recall Mode (page E-26) and use the

and

buttons to scroll

(page E-70).

E-58

Magnetic Declination Correction

With magnetic declination correction, you input a magnetic declination angle (difference between

magnetic north and true north), which allows the watch to indicate true north. You can perform this

procedure when the magnetic declination angle is indicated on the map you are using. Note that you can

input the declination angle in whole degree units only, so you may need to round off the value speciﬁ ed

on the map. If your map indicates the declination angle as 7.4°, you should input 7°. In the case of 7.6°

input 8°, for 7.5° you can input 7° or 8°.

To perform magnetic declination correction

1. In the Digital Compass Mode, hold down the watch’s

button for at

least two seconds. Release

after

-1-

appears.

2. Press

• DEC will appear on the display and then the current magnetic

declination angle setting will ﬂ ash on the display.

3. Use

(East) and

(West) to change the settings.

•

The following explains magnetic declination angle direction

settings.

OFF

: No magnetic declination correction performed. The magnetic

declination angle with this setting is 0°.

: When magnetic north is to the east (east declination)

: When magnetic north is to the west (west declination)

• You can select a value within the range of W 90° to E 90° with

these settings.

• You can turn off (OFF) magnetic declination correction by pressing

and

at the same time.

Magnetic declination angle

direction value (E, W, or OFF)

Magnetic declination

angle value

Magnetic declination angle

direction value (E, W, or OFF)

Magnetic declination

angle value

E-59

• The illustration, for example, shows the value you should input and the direction setting you should

select when the map shows a magnetic declination of 1° West.

4. When the setting is the way you want, press

to exit the setting screen.

Digital Compass Precautions

Magnetic North and True North

The northerly direction can be expressed either as magnetic north or true

north, which are different from each other. Also, it is important to keep in mind

that magnetic north moves over time.

• Magnetic north is the north that is indicated by the needle of a compass.

• True north, which is the location of the North Pole of the Earth’s axis, is the

north that is normally indicated on maps.

• The difference between magnetic north and true north is called the

“declination”. The closer you get to the North Pole, the greater the

declination angle.

Location

• Taking a direction reading when you are near a source of strong magnetism can cause large errors in

readings. Because of this, you should avoid taking direction readings while in the vicinity of the

following types of objects: permanent magnets (magnetic necklaces, etc.), concentrations of metal

(metal doors, lockers, etc.), high tension wires, aerial wires, household appliances (TVs, personal

computers, washing machines, freezers, etc.).

• Accurate direction readings are impossible while in a train, boat, air plane, etc.

• Accurate readings are also impossible indoors, especially inside ferroconcrete structures. This is

because the metal framework of such structures picks up magnetism from appliances, etc.

True north

Earth

Magnetic north

True north

Earth

Magnetic north

E-60

Storage

• The precision of the bearing sensor may deteriorate if the watch becomes magnetized. Because of

this, you should store the watch away from magnets or any other sources of strong magnetism,

including: permanent magnets (magnetic necklaces, etc.) and household appliances (TVs, personal

computers, washing machines, freezers, etc.).

• Whenever you suspect that the watch may have become magnetized, perform the procedure under “To

perform 2-point calibration” (page E-52).

E-61

Taking Barometric Pressure and Temperature Readings

This watch uses a pressure sensor to measure air pressure (barometric pressure) and a temperature

sensor to measure temperature.

To take barometric pressure and temperature readings

Enter the Barometer/Thermometer Mode (page E-27).

•

This will automatically start a barometric pressure/temperature reading

operation, and the results will appear on the display in about one

second.

•

Readings will continue to be taken about every ﬁ ve seconds for the

ﬁ rst three minutes, and then about every two minutes thereafter.

•

You can restart the reading operation from the beginning at any time

by pressing

Note

• Press

to return to the Timekeeping Mode.

• The watch will return to the Timekeeping Mode automatically if you do

not perform any operation for about 1 hour after entering the

Barometer/Thermometer Mode.

Barometric

pressure graph

Barometric

pressure

Pressure

differential

pointer

Temperature

Barometric

pressure graph

Barometric

pressure

Pressure

differential

pointer

Temperature

E-62

Barometric Pressure

• Barometric pressure is displayed in units of 1 hPa (or 0.05 inHg).

•

The displayed barometric pressure value changes to

- - -

if a measured

barometric pressure falls outside the range of 260 hPa to 1,100 hPa (7.65

inHg to 32.45 inHg). The barometric pressure value will reappear as

soon as the measured barometric pressure is within the allowable range.

Temperature

• Temperature is displayed in units of 0.1°C (or 0.2°F).

• The displayed temperature value changes to

- - -

°C (or °F) if a

measured temperature falls outside the range of –10.0°C to 60.0°C

(14.0°F to 140.0°F). The temperature value will reappear as soon as

the measured temperature is within the allowable range.

Display Units

You can select either hectopascals (hPa) or inchesHg (inHg) as the display unit for the measured

barometric pressure, and Celsius (°C) or Fahrenheit (°F) as the display unit for the measured temperature

value. See “To specify temperature, barometric pressure, and altitude display units” (page E-35).

Barometric Pressure Graph

Barometric pressure indicates changes in the atmosphere. By monitoring

these changes you can predict the weather with reasonable accuracy.

This watch takes barometric pressure readings automatically every two

hours. Readings are used to produce barometric pressure graph and

barometric pressure differential pointer readings.

Temperature

Barometric pressure

change indicator

Barometric

pressure

Temperature

Barometric pressure

change indicator

Barometric

pressure

Barometric pressure graphBarometric pressure graph

E-63

Reading the Barometric Pressure Graph

The barometric pressure graph shows a chronological history of pressure readings.

• When display of the barometric change indicator is disabled, the graph shows the results of up to 21

barometric pressure readings (42 hours).

• When display of the barometric change indicator is enabled, the graph shows the results of up to 11

barometric pressure readings (22 hours).

• The horizontal axis of the graph represents time, with each dot standing for

two hours. The rightmost dot represents the most recent reading.

• The vertical axis of the graph represents barometric pressure, with each

dot standing for the relative difference between its reading and that of the

dots next to it. Each dot represents 1 hPa.

The following shows how to interpret the data that appears on the barometric pressure graph.

Rising barometric pressure indicates that upcoming weather will improve.

Falling barometric pressure indicates that upcoming weather will deteriorate.

Note

• If there are sudden changes in weather or temperature, the graph line of past

reading may run off the top or bottom of the display. The entire graph will become

visible once barometric conditions stabilize.

• The following conditions cause the barometric pressure reading to be skipped,

with the corresponding point on the barometric pressure graph being left blank.

– Barometric reading that is out of range (260 hPa to 1,100 hPa or 7.65 inHg to

32.45 inHg)

– Sensor malfunction

Barometric

pressure

Time

Barometric

pressure

Time

Not visible on

the display.

Not visible on

the display.

Operation Guide 3410

E-64

Barometric Pressure Differential Pointer

This pointer indicates the relative difference between the most recent

barometric pressure reading indicated on the barometric pressure graph

(page E-62), and the current barometric pressure value displayed in the

Barometer/Thermometer Mode (page E-61).

Reading Barometric Pressure Differential Pointer

Pressure differential is indicated in the range of

±10 hPa, in 1-hPa units.

• The nearby illustration, for example, shows

what the pointer would indicate when the

calculated pressure differential is

approximately – 5 hPa (approximately – 0.15

inHg).

• Barometric pressure is calculated and

displayed using hPa as the standard. The

barometric pressure differential also can be

read in inHg units as shown in the illustration

(1 hPa

0.03 inHg).

Barometric

pressure

differential

pointer

Barometric

pressure

differential

pointer

−0.15

−5

−10

−0.3

Barometric pressure

differential pointer

inHg values

hPa values

Current pressure

greater than most

recent measured

pressure

Current pressure

less than most

recent measured

pressure

−0.15

−5

−10

−0.3

Barometric pressure

differential pointer

inHg values

hPa values

Current pressure

greater than most

recent measured

pressure

Current pressure

less than most

recent measured

pressure

E-65

Barometric Pressure Change Indications

Your watch analyzes past barometric pressure readings and uses a barometric pressure change indicator

to inform you about changes in pressure.The watch will beep to let you know when a signiﬁ cant change in

barometric pressure is detected. This means you could start taking barometric pressure readings after

reaching a lodge or camp area, and then check the watch the next morning for changes in pressure, and

plan you day’s activities accordingly. Note that you can enable or disable display of the barometric

pressure change indicator as desired.

Reading the Barometric Pressure Change Indicator

Indicator Meaning

Sudden fall in pressure.

Sudden rise in pressure.

Sustained rise in pressure, changing to a fall.

Sustained fall in pressure, changing to a rise.

• The barometric pressure change indicator is not displayed if there has been no noteworthy change in

barometric pressure.

E-66

Important!

• To ensure proper results, take barometric readings under conditions where the altitude remains

constant.

Example

– In a lodge or campground

– On the ocean

• A change in altitude causes a change in barometric pressure. Because of this, correct readings are

impossible. Do not take readings while ascending or descending a mountain, etc.

Enabling or Disabling Display of the Barometric Pressure Change Indicator

You can enable or disable display of the barometric pressure change indicator as desired. When display

of the indicator is enabled, the watch will take a barometric pressure reading every two minutes,

regardless of the mode it is in.

• When

BARO

is shown on the display, it means that barometric pressure change indicator display is

enabled.

To enable or disable the barometric pressure change alert

In the Barometer/Thermometer Mode, hold down

for at least two seconds. Keep

depressed until

the current setting (

INFO Hold ON

INFO Hold OFF

) starts to ﬂ ash on the display.

• If barometric pressure change indicator display is currently enabled,

BARO

will also appear in the

display.

BARO

will not appear if display is currently disabled.

• Note that barometric pressure change indicator display will turn off automatically 24 hours after you

turn it on or battery power goes low.

• Note that time calibration signal reception and power saving (page E-14) are disabled while barometric

pressure change indicator display is enabled.

•

Note that barometric pressure change indicator display cannot be enabled while the watch’s battery is low.

E-67

Using Barometric Pressure and Temperature Records

You can use the procedure in this section to create a barometric pressure and temperature record of your

current readings, along with the date and time of the reading. You can later recall a record to view it.

Important!

• The watch has memory for storage of up to 40 records of various types. If you perform an operation

that creates a new record while there are already 40 records in memory, the oldest record is deleted

automatically to make room for the new one (page E-70).

1. While barometric pressure and temperature readings are in progress, hold down

for at least two

seconds.

• REC and Hold will appear on the display ﬁ rst, and then Hold will disappear. Release

after

Hold disappears.

• The watch will create a record of the current barometric pressure and temperature, along with

the date and time, and then return automatically to the barometric pressure/temperature reading

screen.

2. To view a record, enter the Data Recall Mode (page E-26) and use the

and

buttons to scroll. See

“Viewing Memory Records” (page E-70) for more information.

Pressure Sensor and Temperature Sensor Calibration

The pressure sensor and temperature sensor built into the watch are calibrated at the factory and normally

require no further adjustment. If you notice serious errors in the pressure readings and temperature

readings produced by the watch, you can calibrate the sensor to correct the errors.

Important!

• Incorrectly calibrating the barometric pressure sensor can result in incorrect readings. Before

performing the calibration procedure, compare the readings produced by the watch with those of

another reliable and accurate barometer.

E-68

• Incorrectly calibrating the temperature sensor can result in incorrect readings.

Carefully read the following before doing anything.

–

Compare the readings produced by the watch with those of another reliable and accurate thermometer.

– If adjustment is required, remove the watch from your wrist and wait for 20 or 30 minutes to give the

temperature of the watch time to stabilize.

To calibrate the pressure sensor and the temperature sensor

1. Take a reading with another measurement device to determine the

exact current barometric pressure or temperature.

2. In the Barometer/Thermometer Mode, hold down

for at least two

seconds. You can release

after

TEMP

appears.

• The current temperature calibration setting will ﬂ ash in the display

at this time.

3. Press

to move the ﬂ ashing between the temperature value and

barometric pressure value, to select the one you want to calibrate.

4. Use

(+) and

(

–

) to select the temperature and barometric

pressure value display units as shown below.

Temperature 0.1°C (0.2°F)

Barometric Pressure 1 hPa (0.05 inHg)

• To return the currently ﬂ ashing value to its initial factory default

setting, press

and

at the same time. OFF will appear at

the ﬂ ashing location for about one second, followed by the initial

default value.

5. Press

to return to the Barometer/Thermometer Mode screen.

E-69

Barometer and Thermometer Precautions

• The pressure sensor built into this watch measures changes in air pressure, which you can then apply

to your own weather predictions. It is not intended for use as a precision instrument in ofﬁ cial weather

prediction or reporting applications.

• Sudden temperature changes can affect pressure sensor readings. Because of this, there may be

some error in the readings produced by the watch.

• Temperature reading are affected by your body temperature, direct sunlight, and moisture. To achieve

a more accurate temperature reading, remove the watch from your wrist, place it in a well ventilated

location out of direct sunlight, and wipe all moisture from the case. It takes approximately 20 to 30

minutes for the case of the watch to reach the surrounding temperature.

E-70

Viewing Memory Records

You can use the Data Recall Mode to recall and view the following type of data in watch memory.

• Date/Time Records (page E-30)

• Altitude Records (page E-45)

• Historical altitude values (page E-46)

• Direction Records (page E-56)

• Barometric Pressure and Temperature Records (page E-67)

To view data in watch memory

1. Use

to select the Data Recall Mode (

REC

) as shown on page E-26.

• About one second after REC appears on the display, the display will change to show the ﬁ rst

record of the memory area you were viewing when you last exited the Data Recall Mode.

2. Use

and

to scroll through the screens for an area and display the one you want.

• Records are assigned numbers in the sequence they are recorded. If you create a new record (by

saving data) while there are already 40 records in memory, record number 01 (the oldest record)

will be deleted automatically to make room for the new record.

• If you attempt to recall a record while there are no records in memory, a blank record will appear

on the display.

• Holding the

button will scroll through the records at high speed.

E-71

Historical

altitude

values (4)

* Segment indicating currently displayed record flashes.

Number of

records *

Records (40

maximum)

Currently

displayed

record

Operation Guide 3410

E-72

Records

Month - Day

Hour,

minute,

second

Temperature

(alternating with

month, day)

Barometric

pressure

(alternating

with hour,

minute)

Hour, minute

(alternating with

month, day)

Bearing

Time (alternates

with date)

Altitude

Time Bearing

Barometer/Thermometer

Altitude

E-73

Historical Altitude Values

Hour, minute

(alternating with

month, day)

High

Altitude

Month, day

(alternating with

year) *

Total

Ascent

Hour, minute

(alternating with

month, day)

Low

Altitude

Month, day

(alternating with

year) *

Total

Descent

High Altitude Low Altitude

Total Ascent

Total Descent

* During display of the cumulative ascent or cumulative descent value, shows the

cumulation start date.

E-74

To delete all saved data

Important!

• A delete operation cannot be undone! Make sure you do not need data before you delete it.

In the Data Recall Mode, hold down

for at least ﬁ ve seconds.

Hold

will ﬂ ash on the display ﬁ rst for

about two seconds and then disappear. Keep

depressed.

Hold

will start ﬂ ashing again and then it will

disappear after about ﬁ ve seconds. Release

at this time. - - - - will appear on the display to indicate

that all the data was deleted.

To delete a speciﬁ c record

Important!

• A delete operation cannot be undone! Make sure you do not need data before you delete it.

1. In the Data Recall Mode, use

and

to scroll through records in watch memory until the one you

want to delete is displayed.

2. Hold down

for at least two seconds. First,

CLEAR Hold

will ﬂ ash in the display. After that,

Hold

will

disappear. Release

when

Hold

disappears.

CAUTION!

• Holding down

for more than about ﬁ ve seconds will delete all data currently in watch memory.

E-75

Checking the Current Time in a Different Time Zone

You can use the World Time Mode to view the current time in one of 31 time zones (48 cities) around the

globe. The city that is currently selected in the World Time Mode is called the “World Time City”.

To enter the World Time Mode

Use

to select the World Time Mode (

) as shown on page E-26.

World Time

City time

8:58

Home City

time

22:58

Time offset graphic

(24-hour indication)

Currently selected

Word Time City

Current timekeeping

Mode time

Current time in the currently

selected World Time City

•

After about one second, the city code and name of the currently selected city will scroll across the

display. After that, the city code only will remain on the display.

To view the time in another time zone

In the World Time Mode, use

(East) and

(West) to scroll through city codes.

E-76

To specify standard time or daylight saving time (DST) for a city

1. In the World Time Mode, use

(East) and

(West) to scroll through

the available city codes.

• Keep scrolling until the city code whose Standard Time/Daylight

Saving Time setting you want to change is displayed.

2. Hold down

for at least two seconds.

DST

and

Hold

will appear on

the display ﬁ rst, and then

Hold

will disappear. Release

after

Hold

disappears.

• This will toggle summer time between on and off.

• The DST indicator is displayed while summer time is turned on.

• Using the World Time Mode to change the DST setting of the

city code that is selected as your Home City also will change the

Timekeeping Mode time DST setting.

• Note that you cannot switch between standard time/daylight

saving time (DST) while UTC is selected as the World Time City.

• Note that the standard time/daylight saving time (DST) setting

affects only the currently selected city. Other cities are not

affected.

DST indicatorDST indicator

E-77

Using the Stopwatch

The stopwatch measures elapsed time, split times, and two ﬁ nishes.

To enter the Stopwatch Mode

Use

to select the Stopwatch Mode (

STW

) as shown on page E-26.

To perform an elapsed time operation

A A

Start Stop (Resume) (Stop) Reset

To pause at a split time

C A

Start Split

(

SPLIT

appears

in the upper part

of the display.)

Split release Stop Reset

Current time

1/10-second

graphic

Hours

Seconds

Minutes

1/100 second

Current time

1/10-second

graphic

Hours

Seconds

Minutes

1/100 second

E-78

To measure two ﬁ nishes

A C

Start Split

First runner ﬁ nishes.

(

SPLIT

appears in

the upper part of the

display.)

Display time of ﬁ rst

runner

Stop

Second runner

ﬁ nishes.

Split release

Display time of

second runner

Reset

Note

• The Stopwatch Mode can indicate elapsed time up to 999 hours, 59 minutes, 59.99 seconds.

• Once started, stopwatch timing continues until you press

to stop it, even if you exit the Stopwatch

Mode to another mode and even if timing reaches the stopwatch limit deﬁ ned above. A paused timing

operation will remain paused until you press

to resume it or

to reset.

• Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns

to elapsed time measurement.

• While

SPLIT

is shown in the display, it alternates with the hour digits of the split time at one-second

intervals.

• You can directly access the Stopwatch Mode from the Timekeeping Mode by pressing the

button. If

the stopwatch is reset to all zeros when you enter the Stopwatch mode, the watch will beep twice and

an elapsed time operation will start automatically. You can check whether the stopwatch is reset by

looking at the Timekeeping Mode graphic (page E-29).

E-79

Using the Countdown Timer

The countdown timer can be conﬁ gured to start at a preset time, and sound an alarm when the end of the

countdown is reached.

To enter the Countdown Timer Mode

Use

to select the Countdown Timer Mode (

TMR

) as shown on page E-26.

To specify the countdown start time

1. Enter the Countdown Timer Mode.

• If a countdown is in progress (indicated by the seconds counting

down), press

to stop it and then press

to reset to the current

countdown start time.

• If a countdown is paused, press

to reset to the current

countdown start time.

2. Hold down

for at least two seconds.

• SET Hold will ﬂ ash on the display and then the current start time

setting will start to ﬂ ash. Keep

depressed until the start time

setting starts to ﬂ ash.

3. Press

to move the ﬂ ashing between the hour and minute settings.

4. Use

(+) and

(–) to change the ﬂ ashing item.

• To set the starting value of the countdown time to 24 hours, set 0H 00’00.

5. Press

to exit the setting screen.

Countdown time

(Hour, minutes, seconds)

Minutes

graphic

Current time

Countdown time

(Hour, minutes, seconds)

Minutes

graphic

Current time

Operation Guide 3410

E-80

To perform a countdown timer operation

A A

Start Stop (Restart) (Stop) Reset

• Before starting a countdown timer operation, check to make sure that a countdown operation is not in

progress (indicated by the seconds counting down). If it is, press

to stop it and then

to reset to

the countdown start time.

• An alarm sounds for ten seconds when the end of the countdown is reached. This alarm will sound in

all modes. The countdown time is reset to its starting value automatically when the alarm sounds.

To stop the alarm

Press any button.

E-81

Using the Alarm

You can set ﬁ ve independent daily alarms. When an alarm is turned on, an alarm will sound for about 10

seconds each day when the time in the Timekeeping Mode reaches the preset alarm time. This is true even

if the watch is not in the Timekeeping Mode. One of the daily alarms is a snooze alarm. The other four are

one-time alarms. The snooze alarm will sound every ﬁ ve minutes up to seven times or until it is turned off.

You can also turn on an Hourly Time Signal, which will cause the watch to beep twice every hour on the

hour.

To enter the Alarm Mode

Use

to select the Alarm Mode (

ALM

) as shown on page E-26.

Alarm name

Alarm time

(Hour : Minutes)

Alarm time

19:00

Current time

Alarm ON/OFF

Current time

22:58

24-hour Display *

* Not indicated when the hourly time

signal screen is displayed.

• The alarm name indicates an alarm screen.

SIG

is shown when the Hourly Time Signal screen is on the

display.

• When you enter the Alarm Mode, the data you were viewing when you last exited the mode appears

ﬁ rst.

E-82

To set an alarm time

1. In the Alarm Mode, use

to scroll through the alarm screens until the

one whose time you want to set is displayed.

AL-1 AL-2 AL-3

SIG* SNZ AL-4

* There is no time setting for the hourly time signal.

2. Hold down

until SET Hold appears on the display and then the current settings start to ﬂ ash.

• This is the setting screen.

3. Press

to move the ﬂ ashing between the hour and minute settings.

4. While a setting is ﬂ ashing, use

(+) and

(–) to change it.

• When setting the alarm time using the 12-hour format, take care to set the time correctly as a.m. (no

indicator) or p.m. (P indicator).

5. Press

to exit the setting screen.

• Setting an alarm time causes that alarm to turn on automatically.

E-83

To turn an alarm and the Hourly Time Signal on and off

1. In the Alarm Mode, use

to select an alarm or the Hourly Time

Signal.

2. When the alarm or the Hourly Time Signal you want is selected, press

to turn it on and off.

•

The alarm on indicator (when any alarm is on), snooze alarm indicator

(when the snooze alarm is on), and the Hourly Time Signal on indicator

(when the Hourly Time Signal is on) are shown on the display in all

modes.

To stop the alarm

Press any button.

Note

• The snooze alarm sounds up to seven times at intervals of about ﬁ ve minutes.

• After the snooze alarm ﬁ rst sounds,

SNZ

will ﬂ ash on the display until the snooze alarm sounds all

seven times or until it is canceled.

• The snooze alarm will be canceled when any of the following occurs while the

SNZ

indicator is ﬂ ashing

on the display.

- If you turn off the snooze alarm

- If you display the snooze alarm setting screen

- If you display the Timekeeping Mode setting screen

- If your Home City and World Time City are the same city, and you use the World Time Mode to

change the summer time setting of your Home City

Hourly time signal

on indicator

Snooze

alarm

indicator

Alarm on indicator

Hourly time signal

on indicator

Snooze

alarm

indicator

Alarm on indicator

E-84

Looking up Sunrise and Sunset Times

You can use the Sunrise/Sunset Mode to look up the sunrise and sunset times for a particular date (year,

month, day) and location.

To view sunrise and sunset times

Use

to select the Sunrise/Sunset Mode (

SUN

) as shown on page E-26.

Current date

Sunrise

4:25

Current time *

22:58

Sunrise time

Sunset time

24-hour Display

Sunset

19:00

* Indicated only when the displayed date

is today’s date.

• This will display the sunrise and sunset times for the current date based the currently speciﬁ ed city

code, latitude, and longitude.

• Sunrise/sunset times will not be displayed when battery power is low.

• Before trying to use the Sunrise/Sunset Mode, you need to conﬁ gure settings for the city code,

longitude, and latitude for the location whose sunrise and sunset times you want to view.

• The factory default conﬁ guration of the location is: City Code:

TYO

(Tokyo); Latitude: North 35.7

degrees; Longitude: East 139.7 degrees.

E-85

To view the sunrise/sunset time for a particular date

1. Enter the Sunrise/Sunset Mode.

2. While the sunrise/sunset time are on the display, use

(+) and

(–)

to scroll through the dates.

• Pressing either of the above buttons causes a date (month and

day) to appear on the display.

• When you release the button, the sunrise time of the selected day

will be shown in the middle display, while the sunset time will be

shown in the lower display.

• You can select any date between January 1, 2000 and December

31, 2099.

Note

•

If you think that the sunrise and/or sunset times are not correct for

some reason, check the watch’s city code, longitude and latitude

settings.

• The sunrise and sunset times displayed by this watch are times at

sea level. Sunrise and sunset times are different at altitudes other

than sea level.

Date

Year

Date

Year

E-86

To look up the sunrise and sunset times for a speciﬁ c location

Important!

• If you select a different city code to look up the sunrise and sunset times there, return to the city

code of your Home City (your current location) when you are ﬁ nished. Otherwise, the time shown

in the Timekeeping Mode will not be correct.

• For information about the Home City setting, see “Conﬁ guring Home City Settings” (page E-31).

1. In the Timekeeping Mode, hold down

for at least two seconds.

SET

and

Hold

will appear on the

display ﬁ rst, and then

Hold

will disappear. Release

after

Hold

disappears.

2. Use

(East) and

(West) to select the city code whose sunrise and sunset times you want to view.

• For details about city codes, see the “City Code Table” at the back of this manual.

• If this display shows the information you need, you can exit this procedure at this point by pressing

twice. If you want to specify a latitude and longitude for a more exact reading, advance to step 3,

below.

E-87

3. Press

to display the longitude/latitude setting screen, with the

latitude setting ﬂ ashing.

4. Use

to move the ﬂ ashing between the latitude and the longitude

setting.

5. Use

(+) and

(–) to change the ﬂ ashing setting.

• You can configure the longitude and latitude setting within

following ranges.

Latitude Range: 65.0°S (South 65.0 degrees) to 0°N to 65.0°N

(North 65.0 degrees)

Longitude Range: 179.9°W (West 179.9 degrees) to 0°E to 180.0°E

(East 180.0 degrees)

• Latitude and longitude values are rounded off to the nearest

degree.

6. Press

to return to the Timekeeping Mode.

7. Use

to select the Sunrise/Sunset Mode (

SUN

) as shown on page

E-26.

• Display the location whose sunrise and sunset times you want to

view.

Latitude

Longitude

Press D.

Latitude

Longitude

Press D.

Operation Guide 3410

E-88

Illumination

The display of the watch is illuminated for easy reading in the dark.

The watch’s auto light switch turns on illumination automatically when

you angle the watch towards your face.

• The auto light switch must be turned on (page E-90) for it to operate.

To turn on illumination manually

Press

in any mode to illuminate the display.

• You can use the procedure below to select either 1.5 seconds or three

seconds as the illumination duration. When you press

, the display

will remain illuminated for about 1.5 seconds or three seconds,

depending on the current illumination duration setting.

• The above operation turns on illumination regardless of the current

auto light switch setting.

• Illumination is disabled during time calibration signal reception, while

conﬁ guring sensor measurement mode settings, and during bearing

sensor calibration.

To change the illumination duration

1. In the Timekeeping Mode, hold down

for at least two seconds.

SET

and

Hold

will appear on the

display ﬁ rst, and then

Hold

will disappear. Release

after

Hold

disappears.

2. Use

to cycle through the setting screens until

LIGHT

appears in the display.

• The current illumination duration setting (1 or 3) will be ﬂ ashing in the middle display.

• See the sequence in step 2 of the procedure under “To change the current time and date

settings manually” (page E-33) for information about how to scroll through setting screens.

E-89

3. Press

to toggle the illumination duration between three seconds (

displayed) and 1.5 seconds (

displayed).

4. After all of the settings are the way you want, press

twice to exit the setting screen.

About the Auto Light Switch

Turning on the auto light switch causes illumination to turn on,

whenever you position your wrist as described below in any mode.

Moving the watch to a position that is parallel to the ground and

then tilting it towards you more than 40 degrees causes

illumination to turn on.

Warning!

•

Always make sure you are in a safe place whenever you are reading the display of the watch

using the auto light switch. Be especially careful when running or engaged in any other activity

that can result in accident or injury. Also take care that sudden illumination by the auto light

switch does not startle or distract others around you.

•

When you are wearing the watch, make sure that its auto light switch is turned off before riding

on a bicycle or operating a motorcycle or any other motor vehicle. Sudden and unintended

operation of the auto light switch can create a distraction, which can result in a trafﬁ c accident

and serious personal injury.

More than

40°

Wear the watch on the

outside of your wrist

More than

40°

Wear the watch on the

outside of your wrist

E-90

Note

• This watch features a “Full Auto Light”, so the auto light switch operates only when available light is

below a certain level. It does not illuminate the display under bright light.

• The auto light switch is always disabled, regardless of its on/off setting, when any one of the following

conditions exists.

While an alarm is sounding

While a bearing sensor calibration operation is being performed in the Digital Compass Mode

While a receive operation is in progress in the Receive Mode

While a sunrise or sunset time is being calculated

While in a sensor mode, an auto light switch operation is performed after a sensor reading

To turn the auto light switch on and off

In the Timekeeping Mode, hold down

for at least three seconds to

toggle the auto light switch on (

displayed) and off (

not displayed).

• The auto light switch turns off automatically whenever battery power

drops to Level 4 (page E-11).

Auto light switch on

indicator

Auto light switch on

indicator

E-91

Illumination Precautions

• The LED that provides illumination loses power after very long use.

• Illumination may be hard to see when viewed under direct sunlight.

• Illumination turns off automatically whenever an alarm sounds.

• Frequent use of illumination runs down the battery.

Auto light switch precautions

• Wearing the watch on the inside of your wrist, movement of your arm, or vibration of your arm can

cause frequent activation of the auto light switch and illumination of the display. To avoid running down

the battery, turn off the auto light switch whenever engaging in activities that might cause frequent

illumination of the display.

• Note that wearing the watch under your sleeve while the auto light switch is turned on can cause

frequent illumination of the display and can run down the battery.

• Illumination may not turn on if the face of the watch is more than 15 degrees above

or below parallel. Make sure that the back of your hand is parallel to the ground.

• Illumination turns off after the preset illumination duration (page E-88), even if you

keep the watch pointed towards your face.

• Static electricity or magnetic force can interfere with proper operation of the auto

light switch. If illumination does not turn on, try moving the watch back to the

starting position (parallel with the ground) and then tilt it back towards your face

again. If this does not work, drop your arm all the way down so it hangs at your

side, and then bring it back up again.

• You may notice a very faint clicking sound coming from the watch when it is shaken

back and forth. This sound is caused by mechanical operation of the auto light

switch, and does not indicate a problem with the watch.

E-92

Other Settings

Button Operation Tone

The button operation tone sounds any time you press one of the watch’s buttons. You can turn the button

operation tone on or off as desired.

• Even if you turn off the button operation tone, the alarm, Hourly Time Signal, barometric pressure

change alert, and Countdown Timer Mode alarm all operate normally.

To turn the button operation tone on and off

1. In the Timekeeping Mode, hold down

for at least two seconds.

SET

and

Hold

will appear on the display ﬁ rst, and then

Hold

will disappear.

Release

after

Hold

disappears.

2. Use

to cycle through settings on the display until the current button

operation tone (

MUTE

KEY

) is displayed.

• See the sequence in step 2 of the procedure under “To change the

current time and date settings manually” (page E-33) for

information about how to scroll through setting screens.

Press

to toggle the button operation tone on (

KEY

) and off (

MUTE

4. After all of the settings are the way you want, press

twice to exit the

setting screen.

Note

• The mute indicator is displayed in all modes when the button

operation tone is turned off.

Mute indicatorMute indicator

E-93

Power Saving

For details about Power Saving, see page E-14.

To turn Power Saving on or off

1. In the Timekeeping Mode, hold down

for at least two seconds.

SET

and

Hold

will appear on the display ﬁ rst, and then

Hold

will disappear.

Release

after

Hold

disappears.

2. Use

to cycle through the setting screens until the current power

saving setting (

OFF

) is displayed.

• POWER SAVING will scroll across the upper display at this time.

• See the sequence in step 2 of the procedure under “To change

the current time and date settings manually” (page E-33) for

information about how to scroll through setting screens.

3. Press

to toggle Power Saving on (

) and off (

OFF

4. After all of the settings are the way you want, press

twice to exit the

setting screen.

Note

• The Power Saving on indicator (PS) is on the display in all modes

while Power Saving is turned on.

Power saving

on indicator

Power saving

on indicator

E-94

Troubleshooting

Time Setting

See “Radio Controlled Atomic Timekeeping” (page E-15) for information about adjusting the time setting

according to a time calibration signal.

■

The current time setting is off by hours.

Your Home City setting may be wrong (page E-31). Check your Home City setting and correct it, if

necessary.

■

The current time setting is off by one hour.

If you are using the watch in an area where time calibration signal reception is possible, see “To conﬁ gure

Home City and summer time settings” (page E-31).

If you are using in the watch in an area where time calibration signal reception is not possible, you may

need to change your Home City’s standard time/daylight saving time (DST) setting manually. Use the

procedure under “To change the current time and date settings manually” (page E-33) to change the

standard time/daylight saving time (DST) setting.

Sensor modes

■

I can’t change the temperature, barometric pressure, and altitude display units.

When

TYO

(Tokyo) is selected as the Home City, the altitude unit is set automatically to meters (m), the

barometric pressure unit to hectopascals (hPa), and the temperature unit to Celsius (°C). These settings

cannot be changed.

E-95

■

“ERR” appears on the display while I am using a sensor.

Subjecting the watch to strong impact can cause sensor malfunction or improper contact of internal

circuitry. When this happens,

ERR

(error) will appear on the display and sensor operations will be disabled.

Digital

Compass

Reading

Barometric

Pressure/Temperature

Reading

Altitude

Reading

•

ERR

appears while a reading operation is being performed in a sensor mode, restart the operation. If

ERR

appears on the display again, it can mean there is something wrong with the sensor.

• If

ERR

keeps appearing during a reading operation, it could mean there is a problem with the

applicable sensor.

Operation Guide 3410

E-96

■

Correct altitude readings are not possible.

Relative altitude is calculated based on changes in barometric pressure readings by the pressure sensor.

To minimize the chance of reading error due to changes in barometric pressure, you should update the

reference altitude value before setting off on a trek or any other activity where you plan to take altitude

readings. For more information, see “To specify a reference altitude value” (page E-44).

■

ERR appears on the display after I perform 2-point calibration.

- - -

appears and then changes to

ERR

(error) on the calibration screen, it means that there is something

wrong with the sensor.

• If

ERR

disappears after about one second, try performing the calibration again.

• If

ERR

keeps appearing, contact your original dealer or nearest authorized CASIO distributor to have

the watch checked.

Whenever you have a sensor malfunction, take the watch to your original dealer or nearest authorized

CASIO distributor as soon as possible.

■

What causes incorrect direction readings?

• Incorrect 2-point calibration. Perform 2-point calibration (page E-52).

• Nearby source of strong magnetism, such as a household appliance, a large steel bridge, a steel

beam, overhead wires, etc., or an attempt to take direction readings on a train, boat, etc. Move away

from large metal objects and try again. Note that digital compass operation cannot be performed inside

a train, boat, etc.

E-97

■

What causes different direction readings to produce different results at the same location?

Magnetism generated by nearby high-tension wires is interfering with detection of terrestrial magnetism.

Move away from the high-tension wires and try again.

■

Why am I having problems taking direction readings indoors?

A TV, personal computer, speakers, or some other object is interfering with terrestrial magnetism

readings. Move away from the object causing the interference or take the direction reading outdoors.

Indoor direction readings are particularly difﬁ cult inside ferro-concrete structures. Remember that you will

not be able to take direction readings inside of trains, airplanes, etc.

■

The barometric pressure differential pointer does not appear on the display when I enter the

Barometer/Thermometer Mode.

• This could indicate sensor error. Try pressing

again.

• The barometric pressure differential pointer is not displayed when the displayed current barometric

value is outside of the allowable measurement range (260 to 1,100 hPa).

World Time Mode

■

The time for my World Time City is off in the World Time Mode.

This could be due to incorrect switching between standard time and daylight saving time. See “To specify

standard time or daylight saving time (DST) for a city” (page E-76) for more information.

Charging

■

The watch does not resume operation after I expose it to light.

This can happen after the power level drops to Level 5 (page E-11). Continue exposing the watch to light

until the battery power indicator shows H or M.

E-98

Time Calibration Signal

The information in this section applies only when

LIS

LON

MAD

PAR

ROM

BER

STO

ATH

MOW

HKG

BJS

HNL

ANC

YVR

LAX

YEA

DEN

MEX

CHI

NYC

YHZ

YYT

TPE

SEL

, or

TYO

is selected

as the Home City. You need to adjust the current time manually when any other city is selected as the

Home City.

■

The display shows the ERR indicator when I check the result of the latest receive operation.

Possible Cause Remedy Page

• You are wearing or moving the

watch, or performing a button

operation during the signal

receive operation.

• The watch is in an area with

poor reception conditions.

Keep the watch in an area where reception conditions are good

while the signal receive operation is performed.

E-17

You are in an area where signal

reception is not possible for

some reason.

See “Approximate Reception Ranges”. E-16

The calibration signal is not

being transmitted for some

reason.

• Check the website of the organization that maintains the time

calibration signal in your area for information about its down times.

• Try again later.

–

■

The current time setting changes after I set it manually.

You may have the watch conﬁ gured for auto receive of the time calibration signal (page E-18), which will

cause the time to be adjusted automatically according to your currently selected Home City. If this results

in the wrong time setting, check your Home City setting and correct it, if necessary (page E-31).

E-99

■

The current time setting is off by one hour.

Possible Cause Remedy Page

Signal reception on a day for

switching between standard

time/daylight saving time (DST)

may have failed for some reason.

Perform the operation under “To get ready for a receive operation”.

The time setting will be adjusted automatically as soon as signal

reception is successful.

E-17

If you are unable to receive the time calibration signal, change the

standard time/daylight saving time (DST) setting manually.

E-33

■

Auto receive is not performed or you cannot perform manual receive.

Possible Cause Remedy Page

The watch is not in the

Timekeeping Mode or World

Time Mode.

Auto receive is performed only while the watch is in the Timekeeping

Mode or World Time Mode. Switch to either of these two modes.

E-26

Your Home City setting is wrong. Check your Home City setting and correct it, if necessary. E-31

There is not enough power for

signal reception.

Expose the watch to light to charge it. E-10

■

Signal reception is being performed successfully, but the time and/or day is wrong.

Possible Cause Remedy Page

Your Home City setting is wrong. Check your Home City setting and correct it, if necessary. E-31

The DST setting may be

incorrect.

Change the DST setting to Auto DST. E-31

E-100

Speciﬁ cations

Accuracy at normal temperature:

±15 seconds a month (with no signal calibration)

Timekeeping:

Hour, minutes, seconds, p.m. (P), year, month, day, day of the week

Time format: 12-hour and 24-hour

Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099

Date/Time Records: Up to 40 records (shared storage with altitude, bearing, and barometric pressure/

temperature records)

Other: Two display formats (day of the week screen, barometric pressure graph screen); Home City

code (can be assigned one of 48 city codes); Standard Time / Daylight Saving Time (summer time)

Year display on setting screen only.

Time Calibration Signal Reception:

Auto receive 6 times a day (5 times a day for the Chinese calibration

signal) ; Remaining auto receives cancelled as soon as one is successful; Manual receive;

Receive Mode

Receivable Time Calibration Signals: Mainﬂ ingen, Germany (Call Sign: DCF77, Frequency: 77.5

kHz); Anthorn, England (Call Sign: MSF, Frequency: 60.0 kHz); Fort Collins, Colorado, the

United States (Call Sign: WWVB, Frequency: 60.0 kHz); Fukushima, Japan (Call Sign: JJY,

Frequency: 40.0 kHz); Fukuoka/Saga, Japan (Call Sign: JJY, Frequency: 60.0 kHz) ; Shangqiu

City, Henan Province, China (Call Sign: BPC, Frequency: 68.5 kHz)

Altimeter:

Measurement range: –700 to 10,000 m (or –2,300 to 32,800 ft.) without reference altitude

Display range: –10,000 to 10,000 m (or –32,800 to 32,800 ft.)

Negative values can be caused by readings produced based on a reference altitude or due to

atmospheric conditions.

Display unit: 1 m (or 5 ft.)

E-101

Current Altitude Data: Every second for the ﬁ rst 3 minutes, followed by every 5 seconds for

approximately 1 hour (

0’05

); every second for the ﬁ rst 3 minutes, followed by every 2 minutes for

approximately 12 hours (

2’00

)

Altitude Records:

Up to 40 records (shared storage with date/time, bearing, and barometric pressure/temperature

records)

Historical Altitude Values: 1 record of high altitude, low altitude, cumulative ascent, cumulative

descent

Other: Reference altitude setting; Altitude differential; Altitude auto reading interval (

0’05

2’00

) ;

Altitude Differential Graph

Digital Compass:

60 seconds continuous reading; 16 directions; Angle value 0° to 359°; Four direction

pointers; Calibration (2-point); Magnetic declination correction; Bearing Memory; Bearing Records:

Up to 40 records (shared storage with date/time, altitude, and barometric pressure/temperature

records)

Barometer:

Measurement and display range:

260 to 1,100 hPa (or 7.65 to 32.45 inHg)

Display unit: 1 hPa (or 0.05 inHg)

Reading timing: Daily from midnight, at two hour intervals (12 times per day); Every ﬁ ve seconds in

the Barometer/Thermometer Mode

Barometric Pressure/Temperature Records: Up to 40 records (shared storage with date/time, altitude,

and bearing records)

Other: Calibration; Manual reading (button operation); Barometric pressure graph; Barometric

pressure differential pointer; Barometric pressure change indicator

E-102

Thermometer:

Measurement and display range: –10.0 to 60.0°C (or 14.0 to 140.0°F)

Display unit: 0.1°C (or 0.2°F)

Reading timing: Every ﬁ ve seconds in the Barometer/Thermometer Mode

Other: Calibration; Manual reading (button operation)

Temperature Sensor Precision:

±2°C (±3.6°F) in range of –10°C to 60°C (14.0°F to 140.0°F)

Bearing Sensor Precision:

Direction: Within ±10°

Values are guaranteed for a temperature range of –10°C to 60°C (14°F to 140°F).

North pointer: Within ±2 digital segments

Pressure Sensor Precision:

Measurement accuracy: Within ±3hPa (0.1 inHg) (Altimeter accuracy: Within ± 75m (246 ft.))

• Values are guaranteed for a temperature range of –10°C to 40°C (14°F to 104°F).

• Precision is lessened by strong impact to either the watch or the sensor, and by temperature

extremes.

World Time:

48 cities (31 time zones)

Other: Daylight Saving Time/Standard Time

Stopwatch:

Measuring unit: 1/100 second

Measuring capacity: 999:59' 59.99"

Measuring accuracy: ±0.0006%

Measuring modes: Elapsed time, split time, two ﬁ nishes

E-103

Countdown Timer:

Measuring unit: 1 second

Countdown range: 24 hours

Setting unit: 1 minute

Alarms:

5 Daily alarms (four one-time alarms; one snooze alarm); Hourly time signal

Sunrise/sunset:

Sunrise/sunset time display; selectable date

Illumination:

LED light; Selectable illumination duration (approximately 1.5 seconds or 3 seconds); Auto

Light Switch (Full Auto Light operates only in the dark)

Other:

Battery power indicator; Power Saving; Low-temperature resistance (–10°C/14°F); Button

operation tone on/off

Power Supply:

Solar panel and one rechargeable battery

Approximate battery operating time: 8 months (from full charge to Level 4) under the following

conditions:

• Light: 1.5 seconds/day

• Beeper: 10 seconds/day

• Direction readings: 20 times/month

• Climbs: Once (approximately 1 hour of altitude readings)/month

• Barometric pressure change indicator readings: Approximately 24 hours/month

• Barometric pressure graph: Readings every 2 hours

• Time calibration signal receive: 4 minutes/day

• Display: 18 hours/day

Frequent use of illumination runs down the battery. Particular care is required when using the auto

light switch (page E-91).

Operation Guide 3410

City Code Table

City

Code

City

UTC Offset/

GMT Differential

PPG Pago Pago –11

HNL Honolulu –10

ANC Anchorage –9

YVR Vancouver

–8

LAX Los Angeles

YEA Edmonton

–7

DEN Denver

MEX Mexico City

–6

CHI Chicago

NYC New York –5

SCL Santiago

–4

YHZ Halifax

YYT St. Johns –3.5

RIO Rio De Janeiro –3

FEN

Fernando de

Noronha

–2

RAI Praia –1

City

Code

City

UTC Offset/

GMT Differential

UTC

0LIS Lisbon

LON London

MAD Madrid

PAR Paris

ROM Rome

BER Berlin

STO Stockholm

ATH Athens

+2CAI Cairo

JRS Jerusalem

MOW Moscow

JED Jeddah

THR Tehran +3.5

DXB Dubai +4

KBL Kabul +4.5

KHI Karachi +5

L-1

City

Code

City

UTC Offset/

GMT Differential

DEL Delhi +5.5

KTM Kathmandu +5.75

DAC Dhaka +6

RGN Yangon +6.5

BKK Bangkok +7

SIN Singapore

HKG Hong Kong

BJS Beijing

TPE Taipei

SEL Seoul

TYO Tokyo

ADL Adelaide +9.5

GUM Guam

+10

SYD Sydney

NOU Noumea +11

WLG Wellington +12

* As of December 2012, the ofﬁ cial UTC offset

for Moscow, Russia (MOW) was changed from

+3 to +4, but this watch still uses an offset of

+3 (the old offset) for MOW. Because of this,

you should leave the summer time setting

turned on (which advances the time by one

hour) for the MOW time.

• The rules governing global times (GMT

differential and UTC offset) and summer time

are determined by each individual country.

Operation Guide 3410

G-Shock H-1 Owner's manual

Brand: G-Shock

Model: H-1

Category: Water pumps

Type: Owner's manual

This manual is also suitable for

Download PDF

report

G-Shock H-1 Owner's manual

This manual is also suitable for

G-Shock H-1 Owner's manual

Related papers

Other documents