Mackie S410s User manual

Brand: Mackie

Model: S410s

Category: Audio amplifiers

Type: User manual

S410s PASSIVE

SUBWOOFER

USER’S MANUAL

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including ampliﬁ ers) that produce heat.

Only use attachments/accessories speciﬁ ed by the manufacturer.

10.

Use only with a cart, stand, tripod, bracket, or table speciﬁ ed by the

manufacturer, or sold with the apparatus. When a cart is used, use

caution when moving the cart/apparatus combination to avoid injury

from tip-over.

11.

Refer all servicing to qualiﬁ ed service personnel. Servicing is required

when the apparatus has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

12.

Exposure to extremely high noise levels may cause permanent hearing

loss. Individuals vary considerably in susceptibility to noise-induced

hearing loss, but nearly everyone will lose some hearing if exposed to

sufﬁ ciently intense noise for a period of time. The U.S. Government’s

Occupational Safety and Health Administration (OSHA) has speciﬁ ed

the permissible noise level exposures shown in the following chart.

According to OSHA, any exposure in excess of these permissible limits

could result in some hearing loss. To ensure against potentially danger-

ous exposure to high sound pressure levels, it is recommended that all

persons exposed to equipment capable of producing high sound pres-

sure levels use hearing protectors while the equipment is in operation.

Ear plugs or protectors in the ear canals or over the ears must be worn

when operating the equipment in order to prevent permanent hearing

loss if exposure is in excess of the limits set forth here.

IMPORTANT SAFETY INSTRUCTIONS

WARNING — To reduce the risk of

ﬁ re or electric shock, do not expose this

apparatus to rain or moisture.

Duration Per Day Sound Level dBA, Typical

In Hours Slow Response Example

8 90 Duo in small club

6 92

4 95 Subway Train

3 97

2 100 Very loud classical music

1.5 102

1 105 Tami screaming at Adrian about deadlines

0.5 110

0.25 or less 115 Loudest parts at a rock concert

PORTABLE CART WARNING

Carts and stands - The

Component should be used

only with a cart or stand

that is recommended by

the manufacturer.

A Component and cart

combination should be

moved with care. Quick

stops, excessive force, and

uneven surfaces may cause

the Component and cart

combination to overturn.

Don’t forget to visit our website at www.mackie.com

for more information about this and oth er Mackie products.

INTRODUCTION

The woofers incoporate technology used in large-format

touring systems and are virtually indestructible.

Connecting and setting up the S410s is a breeze. It

accepts a speaker-level signal via a Neutrik Speakon

connector and has a second Speakon connector for dai-

sy-chaining the signal to another speaker. The built-in

180 Hz low-pass ﬁ lter allows you to connect a full-range

signal directly to the input of the subwoofer.

The cabinet is constructed using 18 mm multi-layer

birch plywood. A carrying handle is integrated into each

side for easy loading and transport, and optional casters

can be installed on the back of the cabinet for even

easier transport.

Thank you for choosing the Mackie S410s sound rein-

force ment subwoofer.

The S410s is a professional passive subwoofer, de-

signed to complement our professional line of passive

and active loudspeakers, powered mixers, and power am-

pliﬁ ers. It is capable of extremely high sound-pressure

levels, and designed to give you the best performance of

any subwoofer in its class and price range.

The S410s features four 10-inch high-power low-

frequency woofers in a bass-reﬂ ex designed cabinet.

Using four smaller drivers rather than one large 15"

driver has several advantages.

• Smaller drivers provide better transient response

for a “punchier” sound.

• Four 10" drivers provide more surface area than a

single 15” driver to move more air.

• The quad-driver conﬁ guration provides better

power handling and improved efﬁ ciency over a

single 15" driver.

Contents

IMPORTANT SAFETY INSTRUCTIONS..................................................................................................2

INTRODUCTION.........................................................................................................................................3

HOOKUP DIAGRAMS ................................................................................................................................4

Quick-Start........................................................................................................................................................................... 4

CONNECTIONS.......................................................................................................................................... 6

PLACEMENT................................................................................................................................................ 6

Room Acoustics .................................................................................................................................................................. 6

SERVICE INFORMATION.......................................................................................................................... 8

Warranty Service................................................................................................................................................................ 8

Troubleshooting ................................................................................................................................................................. 8

Repair..................................................................................................................................................................................... 8

CARE AND MAINTENANCE..................................................................................................................... 9

S410s SPECIFICATIONS............................................................................................................................. 9

S410s LIMITED WARRANTY....................................................................................................................11

Part No. 0015329 Rev. B 7/05

HOOKUP DIAGRAMS

Quick-Start

Make all initial connections with the

power switches OFF on all equip-

ment. Make sure all master volume,

level, or gain controls are all the way

down.

1. Connect the line-level outputs from your mixing

console (or other signal source) to the inputs of

your power ampliﬁ er.

2. Connect the “Speaker Output” from your power

ampliﬁ er (or powered mixer) to the INPUT connec-

tor on the S410s.

3. Turn on your mixing console (or other signal

source).

4. Turn on the ampliﬁ er. Turn up its volume or gain

control(s) as recommended by the manufacturer.

5. Start the signal source, whether it be speaking

into a microphone or starting a CD player. Adjust

the volume controls on the mixer (or other signal

source) for normal operation.

S410

AND S408

: WITH A MIXER AND TWO POWER AMPLIFIERS

S408

"MACKIE" AND THE "RUNNING MAN" FIGURE

S408

"MACKIE" AND THE "RUNNING MAN" FIGURE

S408S408

S410s

"MACKIE" AND THE "RUNNING MAN" FIGURE

S410s

"MACKIE" AND THE "RUNNING MAN" FIGURE

S410sS410s

Mixer or

Preamplifier

Right

Line-level

Output

Left

Line-level

Output

Mono Bridged

Power Amplifier

1202-VLZ PRO

Mono Bridged

Power Amplifier

S410

AND S408

: WITH A MIXER AND POWER AMPLIFIER

S410

AND S408

: WITH A MIXER AND TWO POWER AMPLIFIERS

Po l e

Mount

Po l e

Mount

S410s S410

S408 S408

Mixer or

Preamplifier

Right

Line-level

Output

Left

Line-level

Output

Stereo

Power Amplifier

1202-VLZPRO

Po l e

Mount

Po l e

Mount

S410s S410

S408 S408

Mixer or

Preamplifier

Thru

Connections

Right

Line-level

Output

Left

Line-level

Output

Stereo

Power Amplifier

1202-VLZPRO

Stereo

Power Amplifier

CONNECTIONS

The S410s has two connectors labeled INPUT and

THRU. These are both Neutrik Speakon™ connectors,

which provide a secure and reliable connection for loud-

speakers and subwoofers. These connectors are wired

in parallel, and allow for connecting the input signal to

another speaker’s input.

NEVER connect more than one

output from a power ampliﬁ er to the

S410s INPUT or THRU connectors.

Keep in mind, when connecting two or more speakers

in parallel using the “thru” connections, that you want

to avoid going below the minimum impedance require-

ments for your power ampliﬁ er.

The S410s has a nominal impedance

of 8 ohms.

Two 8 ohm cabinets in parallel equals

4 ohms.

Three 8 ohm cabinets in parallel equals

2.7 ohms.

Four 8 ohm cabinets in parallel

equals 2 ohms.

Use high-quality speaker cable as recommended by

the power ampliﬁ er manufacturer.

DO NOT use coaxial shielded cable

like a guitar cord to make speaker

connections. They are not designed

to handle the high currents required

to drive a loudspeaker.

The Speakon connector is wired as follows:

Pin 1+ = Signal (“+” or hot)

Pin 1– = Ground (“–” or cold)

PLACEMENT

The S410s subwoofer is designed to sit on the ﬂ oor

or stage. A socket is provided on the top of the cabinet

for mounting another speaker on top of the S410s, like

the Mackie S408 two-way loudspeaker. Use the optional

Mackie speaker mounting pole (SPM100) to mount

them on the S410s (see Hookup Diagrams on page 5).

WARNING: The cabinet has no rig-

ging points and is not suitable for

rigging. NEVER attempt to suspend

the S410s by its handles.

As with any powered components,

protect them from moisture. If you

are setting them up outdoors, make

sure they are under cov er if you

expect rain.

Room Acoustics

The S410s subwoofers are designed to sound as neu-

tral as possible; that is, to reproduce the input signal as

accurately as possible.

Room acoustics play a crucial role in the overall per-

formance of a sound system. Here are some additional

placement tips to help overcome some typical room

problems that might arise:

• Avoid placing loudspeakers in the corners of a

room. This increases the low frequency output and

can cause the sound to be muddy and indistinct.

• Avoid placing loudspeakers against a wall. This, too,

increases the low frequency output, though not as

much as corner placement. However, if you do need

to reinforce the low frequencies, this is a good way

to do it.

• Avoid placing the speakers directly on a hollow

stage ﬂ oor. A hollow stage can resonate at certain

frequencies, causing peaks and dips in the fre-

quency response of the room. It’s better to place the

loudspeakers on a sturdy table or stand designed to

handle the weight of the cabinet(s).

COLD

HOT

1–

2–

Speakon Connectors

•

Position the full-range loudspeakers so the high-

frequency drivers are 2 to 4 feet above ear level

for the

audience (make allowances for a standing/

dancing in the aisles audience). High frequencies

are highly directional and tend to be absorbed

much easier than lower frequencies. By providing

direct line-of-sight from the loudspeakers to the

audience, you increase the overall brightness and

intelligibility of the sound system.

•

Highly reverberant rooms, like many gymnasiums

and auditoriums, are a nightmare for sound system

intelligibility. Multiple reﬂ ections off the hard walls,

ceiling, and ﬂ oor play havoc with the sound. Depend-

ing on the situation, you may be able to take some

steps to minimize the reﬂ ections, such as putting

carpeting on the ﬂ oors, closing draperies to cover

large glass windows, or hanging tapestries or other

materials on the walls to absorb some of the sound.

However, in most cases, these remedies are not

possible or practical. So what do you do? Making

the sound system louder generally doesn’t work

because the reﬂ ections become louder, too. The

best approach is to provide as much direct sound

coverage to the audience as possible. The farther

away you are from the speaker, the more prominent

will be the reﬂ ected sound.

Use more speakers strategically placed so they are

closer to the back of the audience. If the distance

between the front and back speakers is more than

about 100 feet, you should use a delay processor to

time-align the sound. (Since sound travels about 1

foot per millisecond, it takes about 1/10 of a second

to travel 100 feet.)

Repair

Service for Mackie products is available at a factory-

authorized service center. Service for Mackie products

outside the United States can be obtained through local

dealers or distributors.

If your S410s needs ser vice, please fol low these

in struc tions:

1. Review the preceding trou ble shoot ing sug ges tions.

Please.

2. Call Tech Support at 1-800-898-3211, 7 am to 5 pm

PST, to explain the prob lem in detail. They will ask

you all sorts of impertinent questions in the hope of

sorting out the problem. If it appears that the S410s

needs repair, you will be given a Service Request

Number. Have your subwoofer’s serial number

ready. You must have a Service Request Num ber be-

fore you can obtain service at a factory-au tho rized

service center.

3. Keep this user’s manual. We don’t need it to repair

the subwoof er.

4. Pack the subwoofer in its original pack ag ing,

including protective wrap, endcaps, and box. This

is VERY IMPORTANT. When you call for the Service

Request Number, please let Tech Support know if

you need new pack ag ing. Mackie is not re spon si ble

for any damage that occurs due to non-factory

pack ag ing.

5. Include a legible note stating your name, shipping

address (no P.O. boxes), daytime phone number,

Service Request Number, and a detailed de scrip tion

of the prob lem, in clud ing how we can duplicate it.

6. Write the Service Request Number in

BIG

on top of the box. Product shipped with-

out the Service Request Number will be refused.

7. Tech Support will tell you where to ship the sub-

woofer for repair. We suggest insurance for all forms

of cart age.

8. We’ll try to ﬁ x the subwoofer with in ﬁ ve business

days. Once it is repaired, we’ll ship it back the same

way in which it was received. This para graph does

not nec es sar i ly apply to non-war ran ty service.

Note: You must have a sales receipt from an Autho-

rized Mackie Dealer to qualify for a warranty repair.

SERVICE INFORMATION

Warranty Service

Details concerning warranty service are spelled out

on page 11 of this manual.

If you think your subwoofer has a prob lem, please do

everything you can to con ﬁ rm it before calling for service,

in clud ing reading through the following Trou ble shoot ing

sec tion. Doing so might save you from being de prived of

your Mack ie subwoofer.

Of all Mackie prod ucts returned for ser vice (which is

hardly any at all), many are coded “CND” — Could Not

Duplicate— which usually means the problem lay some-

where else in the sys tem. The following trou ble shoot ing

tips may sound obvious, but here are some things you

can check:

Troubleshooting

No sound

• Are the level controls on the mixer or ampliﬁ er

turned all the way down? Follow the procedures in

the “Quick-Start” section on page 4 to verify that

all the vol ume controls in the system are properly

ad just ed.

• Is the signal source working (and making union

scale)? Make sure the con nect ing cables are in good

repair and se cure ly connected at both ends.

• Make sure the mixer does not have a Mute on or a

Processor loop en gaged. If you ﬁ nd something like

this, make sure the volume/gain is turned down

before disengaging the offending switch.

Poor bass performance

• Check the polarity of the connections between the

mixer and all the loud speak ers and subwoofers.

You may have your positive and negative connec-

tions re versed at one end of one cable, causing one

loud speak er to be out-of-phase.

Poor sound

• Is it loud and distorted? Make sure that you’re not

overdriving a stage in the signal chain. Verify that

all level controls are set properly.

• Is the input connector plugged com plete ly into the

jack? Make sure all con nec tions are secure. It’s a

good idea to periodically clean all electrical con-

nec tions with a non-lu bri cat ing electrical contact

cleaner.

S410s SPECIFICATIONS

Acoustic Performance

Frequency Range (–10 dB)

40 Hz–400 Hz

Sensitivity 96.3 dB @ 1 W/1 m

Max SPL long-term 131 dB @ 1m

Max SPL peak 134 dB @ 1m

Crossover Point 180 Hz, 12 dB/octave

Woofer Loading Bass reﬂ ex

Input/Output

INPUT/THRU Type Neutrik Speakon™

Input Impedance (nominal)

8 ohms

Input Impedance (minimum)

3.8 ohms @ 110 Hz

Recommended Lowpass Filter (if using external

crossover) 150 Hz, 24 dB/octave

Power Handling 750 watts rms continuous

3000 watts peak

Low-Frequency Section

Woofer Diameter 10.0 in/254 mm

Voice Coil Diameter 2 in/51 mm

Diaphragm Material Paper

Magnet Material Ferrite

Construction Features

Basic Design Bass reﬂ ex

Material 18 mm multi-layered plywood

Finish Black paint

Handles

One on each side

Grille Perforated metal with weather-

resistant coating

Physical Properties

Height 28.0 in/71.1 cm

Width 24.0 in/61.0 cm

Depth 25.0 in/63.5 cm

Weight 95 lb/43.1 kg

Mounting Methods Floor mount only.

The S410s cabinet has no rigging points and is

not

suitable for ﬂ ying. Never attempt to suspend

the

cabinet by its handles.

Options

Casters Set of four casters for mounting on

the rear of the cabinet.

See Caster Installation instructions

on next page.

Disclaimer

Since we are always striving to make our products better by in-

cor po rat ing new and im proved ma te ri als, com po nents, and man u fac -

tur ing methods, we re serve the right to change these spec i ﬁ ca tions

at any time with out no tice.

“Mackie” and the “Running Man” ﬁ gure are reg is tered trade marks

of LOUD Technologies Inc.

All other brand names men tioned are trade marks or registered

trademarks of their respective hold ers, and are hereby ac knowl edged.

CARE AND MAINTENANCE

Your Mackie subwoofer will pro vide many years of reli-

able ser vice if you fol low these guide lines:

Avoid exposing the subwoofer to

mois ture. If your loudspeakers are

set up out doors, be sure they are

under cover if you expect rain.

Need Help?

You can reach a technical support representative

Monday through Friday

from 7 AM to 5 PM PST at:

1-800-898-3211

After hours, visit www.mackie.com and click Support,

or email us at: t[email protected]

• Avoid exposure to extreme cold (be low freezing

tem per a tures). If you must operate the subwoof-

ers in a cold en vi ron ment, warm up the voice coil

slowly by sending a low-level sig nal through it for

about 15 minutes prior to high-power op er a tion.

• Use a slighty damp cloth with a mild soap so lu tion

to clean the cabinets. Only do this when the power

is turned off. Avoid getting mois ture into any of

the open ings of the cab i net, par tic u lar ly where the

driver is located.

S410s Dimensions

S410s Frequency Response On-Axis

28.0 in/

71.1 cm

25.0 in/

63.5 cm

24.0 in/

61.0 cm

25.0 in/

63.5 cm

24.0 in/

61.0 cm

24.0 in/

61.0 cm

Frequency (Hz)

20 100 1000

110

100

1/3 Octave Response

dB SPL @ 2.83 V

1. Remove existing bolts.

2. Align fixed caster (part number

150007) over holes.

3. Secure with four

1/4-20 x 1-1/2" hex bolts

(part number 102022) with one

flat washer (part number 105005)

and one lock washer (part number 105004)

per bolt.

1. Remove existing bolts.

2. Align swivel caster (part number

150001) over holes.

3. Secure with four

1/4-20 x 1-1/2" hex bolts

(part number 102022) with one

flat washer (part number 105005)

and one lock washer (part number 105004)

per bolt.

Parts List

2 – Swivel Casters (150001)

2 – Fixed Casters (150007)

16 – 1/4-20 x 1-1/2" hex bolts (102022)

16 – Flat Washers 1/4" 18-8 (105005)

16 – Lock Washers 1/4" 18-8 (105004)

S410s Caster Installation

A. LOUD Technologies Inc. warrants all materials,

workmanship

and proper operation of this product for a

period of two years

from the original date of purchase. If

any defects are found in the materials or workmanship or if

the product fails to function properly during the applicable

warranty period, LOUD Technologies, at its option, will

repair or replace the product. This warranty applies only

to equipment sold and delivered within the U.S. by

LOUD Technologies Inc. or its authorized dealers.

B. Failure to register online or return the product

registration card will not void the two-year warranty.

C. Service and repairs of Mackie products are to be

performed only at a factory-authorized facility (see D

below). Unauthorized service, repairs, or modiﬁ cation will

void this warranty. To obtain repairs under warranty, you

must have a copy of your sales receipt from the authorized

Mackie dealer where you purchased the product. It is

necessary to establish purchase date and determine whether

your Mackie product is within the warranty period.

D. To obtain factory-authorized service:

1. Call Mackie Technical Support at 800/898-3211,

7 AM to 5 PM Monday through Friday (Paciﬁ c Time)

to get a Service Request Number. Products returned

without a Service Request Number will be refused.

2. Pack the product in its original shipping carton. Also

include a note explaining exactly how to duplicate the

problem, a copy of the sales receipt with price and date

showing, and your return street address (no P.O. boxes

or route numbers, please!). If we cannot duplicate the

problem or establish the starting date of your Limited

Warranty, we may, at our option, charge for service time.

3. Ship the product in its original shipping carton,

freight prepaid to the authorized service center. The

address of your closest authorized service center will be

given to you by Technical Support.

IMPORTANT: Make sure that the Service Request

Number is plainly written on the shipping carton.

E. LOUD Technologies reserves the right to inspect

any products that may be the subject of any warranty

claims before repair or replacement is carried out. LOUD

Technologies may, at our option, require proof of the

original date of purchase in the form of a dated copy

of the original dealer’s invoice or sales receipt. Final

determination of warranty coverage lies solely with LOUD

Technologies.

F. Any products returned to one of the LOUD Technologies

factory-authorized service centers and deemed eligible for

repair or replacement under the terms of this warranty will

be repaired or replaced within thirty days of receipt. LOUD

Technologies and its authorized service centers may use

refurbished parts for repair or replacement of any product.

Products returned to LOUD Technologies that do not meet

the terms of this Warranty will be not be repaired unless

payment is received for labor, materials, return freight,

and insurance. Products repaired under warranty will be

returned freight prepaid by LOUD Technologies to any

location within the boundaries of the USA.

G. LOUD Technologies warrants all repairs performed

for 90 days or for the remainder of the warranty period.

This warranty does not extend to damage resulting from

improper installation, misuse, neglect or abuse, or to

exterior appearance. This warranty is recognized only if

the inspection seals and serial number on the unit have not

been defaced or removed.

H. LOUD Technologies assumes no responsibility for the

quality or timeliness of repairs performed by an authorized

service center.

I. This warranty is extended to the original purchaser and

to anyone who may subsequently purchase this product

within the applicable warranty period. A copy of the

original sales receipt is required to obtain warranty repairs.

J. This is your sole warranty. LOUD Technologies does

not authorize any third party, including any dealer or

sales representative, to assume any liability on behalf of

LOUD

Technologies or to make any warranty for LOUD

Technologies Inc.

K. THE WARRANTY GIVEN ON THIS PAGE IS THE SOLE

WARRANTY GIVEN BY LOUD TECHNOLOGIES INC.

AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

AND IMPLIED, INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE. THE WARRANTY GIVEN ON THIS PAGE

SHALL BE STRICTLY LIMITED IN DURATION TO TWO

YEARS FROM THE DATE OF ORIGINAL PURCHASE

FROM AN AUTHORIZED MACKIE DEALER. UPON

EXPIRATION OF THE APPLICABLE WARRANTY PERIOD,

LOUD TECHNOLOGIES INC. SHALL HAVE NO FURTHER

WARRANTY OBLIGATION OF ANY KIND. LOUD

TECHNOLOGIES INC. SHALL NOT BE LIABLE FOR ANY

INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES

THAT MAY RESULT FROM ANY DEFECT IN THE MACKIE

PRODUCT OR ANY WARRANTY CLAIM. Some states do

not allow exclusion or limitation of incidental, special,

or consequential damages or a limitation on how long

warranties last, so some of the above limitations and

exclusions may not apply to you. This warranty provides

speciﬁ c legal rights and you may have other rights which

vary from state to state.

Please keep your sales re ceipt in a safe place.

S410s LIMITED WARRANTY

16220 Wood-Red Road NE • Woodinville, WA 98072 • USA

US and Canada: 800.898.3211

Europe, Asia, Central and South America: 425.487.4333

Middle East and Africa: 31.20.654.4000

Fax: 425.487.4337 • www.mackie.com

E-mail: sales@mackie.com

Mackie S410s User manual

Brand: Mackie

Model: S410s

Category: Audio amplifiers

Type: User manual

Download PDF

report

Mackie S410s User manual

Mackie S410s User manual

Related papers

Other documents