ECX700-AL
Ruggedized Fanless Embedded System
Installation Guide
Preliminary
X Outlook
LAN port
M12 A code (8pin)
Circular 23pin
2 COM& 2Can bus
USB 3.0
USB 3.0
Power status
LED
Power DC-IN
M12 D code
(4pin)
N type conn.
For wifi Antenna
N type conn.
For wifi Antenna
SIM slot HDMI
N type conn for LTE
antenna
N type conn for LTE
antenna
Vent
Installation Guide | ECX700-AL
Installation Guide | ECX700-AL
X Cable Assembly –LAN cable
LAN port
M12 A code (8pin)
LAN converter cable to
connect ECX700 and
device cable
This is a standard LAN converter cable after
assembly; customer can either use our converter
cable or a customized cable to directly connect
ECX700 with their devices
X Cable Assembly –23pin 1to4 cable
Circular 23pin
2 COM& 2Can
bus
23pin 1to4 converter
cable to connect
ECX700 and cables of
RS232 or CAN devices
This is a standard 23pin 1to4 converter cable
after assembly; customer can either use our
converter cable or a customized cable to directly
connect ECX700 with their devices
X Cable Assembly –USB cable
USB 3.0
USB3.0 converter cable
to connect ECX700 and
cables of customer’s
USB devices
This is a standard USB
converter cable after
assembly; customer
can either use our USB
converter cable or a
customized cable to
directly connect
ECX700 with their USB
devices
Power DC-IN
M12 D code
(4pin)
Power adaptor
converter cable to
connect ECX700 and
cables of customer’s
power adaptor
This is a standard power converter cable after
assembly; customer can either use our power
converter cable or a customized cable to directly
connect ECX700 with their power adaptor
Installation Guide | ECX700-AL
Installation Guide | ECX700-AL
X Cable Assembly –HDMI cable
HDMI
HDMI converter cable
to connect ECX700 and
cables of customer’s
HDMI Display
This is a standard HDMI converter cable after
assembly; customer can either use our HDMI
converter cable or a customized cable to directly
connect ECX700 with their Display
X Dimensions
Installation Guide | ECX700-AL
Installation Guide | ECX700-AL
Installation Guide | ECX700-AL
X Boot up the system-1
Step1:
To prepare an external
power cable
Step 2:
To make sure the M12 D code
of the external power cable is
connected with ECX700
Step 3:
To make sure the DC jack of the
external power cable is
connected with power adaptor
X Boot up the system-2
Step 4:
Notice that your adaptor’s power
pin is the same with the following
Step 5:
When PWR LED turns into
Green, it means the system has
been already booted up
ECX700 Power Pin Definition
Pin-1 GND
Pin-2 GND
Pin-3 VCC
Pin-4 VCC
X Boot up the system-3
Step 6:
Use external HDMI cable to
connect ECX700 and HDMI display
Step 7:
Connect external HDMI cable
with ECX700
Step 8:
Operation system is ready
Installation Guide | ECX700-AL
Installation Guide | ECX700-AL
Installation Guide | ECX700-AL
-
1
-
2
-
3
-
4
-
5
DFI ECX700-AL Installation Guide User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Lantronix Snapdragon™ 845 Mobile HDK User guide
-
-
Hitachi KHWS1WUN User manual
-
Contec DIO-6464LX-USB Owner's manual
-
-
-
-
LG SKSWK245LS Owner's manual
-
MiTAC MX1-10FEP-C246 User manual
-
LG Electronics 60LN57**-ZE User manual