Hunter Fan 28450 Owner's manual

Brand: Hunter Fan

Model: 28450

Type: Owner's manual

42005-01 • 01/31/05

Hunter Fan Company 42005-01 • 01/31/05

42005-01 • 01/31/05 Hunter Fan Company

Welcome

Your new Hunter

ceiling fan is an addition to your home or oce that

will provide comfort and performance for many years. is installation

and operation manual gives you complete instructions for installing

and operating your fan.

We are proud of our work. We appreciate the opportunity to supply

you with the best ceiling fan available anywhere in the world.

Before installing your fan, for your records and warranty assistance,

record information from the carton and Hunter nameplate label

(located on the top of the fan motor housing).

Cautions and Warnings

• Read this entire manual carefully before beginning installation. Save

these instructions.

• Use only Hunter replacement parts.

• To reduce the risk of personal injury, attach the fan directly to the

support structure of the building according to these instructions,

and use only the hardware supplied.

• To avoid possible electrical shock, before installing your fan,

disconnect the power by turning o the circuit breakers to the

outlet box and associated wall switch location. If you cannot lock

the circuit breakers in the o position, securely fasten a prominent

warning device, such as a tag, to the service panel.

• All wiring must be in accordance with national and local electrical

codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a

qualied electrician.

• To reduce the risk of personal injury, do not bend the blade

attachment system when installing, balancing, or cleaning the fan.

Never insert foreign objects between rotating fan blades.

• To reduce the risk of re, electrical shock, or motor damage, do not

use a solid-state speed control with this fan. Use only Hunter speed

controls.

For Your Records and Warranty

Assistance

Model Name: _____________________

Catalog/Model No.: ________________

Serial No.: _______________________

Date Purchased: ___________________

Where Purchased: _________________

For reference also attach your receipt or a

copy of your receipt to the manual.

Table of Contents

1 • Getting Ready ...................................................4

2 • Installing the Hanger Bracket...................5

3 • Assembling and Hanging the Fan..........6

4 • Wiring the Fan..................................................8

5 • Installing the Canopy and

Canopy Trim Ring............................................9

6 • Assembling the Blades.............................. 10

7 • Installing the Switch Housing................ 11

8 • Operating and Cleaning

Your Ceiling Fan ........................................... 12

9 • Troubleshooting........................................... 13

Hunter Fan Company 42005-01 • 01/31/05

42005-01 • 01/31/05 Hunter Fan Company

Installer’s Choice and Optional Accessories

Understanding Mounting and Installer’s Choice®

Hunter’s patented 3-position mounting system provides you maximum

installation  exibility and ease. You can install your Hunter fan in one

of three ways, depending on ceiling height and your preference: Low

Pro le, Standard, or Angle mounting.  e steps in this manual include

instructions for all three Installer’s Choice mounting methods.

Considering Optional Accessories

Consider using Hunter’s optional accessories, including a wall-mounted

or remote speed control. To install and use the accessories, follow

the instructions included with each product. For quiet and optimum

performance of your Hunter fan, use only Hunter speed controls.

Low Pro le Mounting  ts close to the

ceiling, recommended for ceilings less

than 8 feet high

Standard Mounting hangs from

the ceiling by a downrod (included),

recommended for ceilings 8 feet or higher

Angle Mounting recommended for a

vaulted or angled ceiling

For ceilings higher than 8 feet, you

can purchase Hunter extension

downrods. All Hunter fans use sturdy

3/4” diameter pipe to assure stability

and wobble-free performance.

Hunter Fan Company 42005-01 • 01/31/05

42005-01 • 01/31/05 Hunter Fan Company

1 • Getting Ready

To install a ceiling fan, be sure you can do the following:

• Locate the ceiling joist or other suitable support in ceiling.

• Drill holes for and install wood screws.

• Identify and connect electrical wires.

• Lift 40 pounds.

If you need help installing the fan, your Hunter fan dealer can direct

you to a licensed installer or electrician.

Gathering the Tools

You will need the following tools for installing the fan:

• Electric drill with 9/64” bit

• Standard screwdriver

• Phillips-head screwdriver

• Wrench or pliers

Check Your Fan Parts

Carefully unpack your fan to avoid damage to the fan parts. Check

for any shipping damage to the motor or fan blades. If one of the fan

blades was damaged in shipment, return all the blades for replacement.

If any parts are missing or damaged, contact your Hunter dealer or call

Hunter Parts Department at 888-830-1326.

Preparing the Fan Site

Before you begin installing the fan, follow all the instructions in

the pullout sheet called “Preparing the Fan Site.” Proper ceiling fan

location and attachment to the building structure are essential for

safety, reliable operation, maximum e ciency, and energy savings.

Installing Multiple Fans?

If you are installing more than

one fan, keep the fan blades in

sets, as they were shipped.

Hunter Fan Company 42005-01 • 01/31/05

42005-01 • 01/31/05 Hunter Fan Company

2 • Installing the Hanger Bracket

2-1. Drill two pilot holes into the wood support structure through the

outermost holes in the outlet box. e pilot holes should be 9/64”

in diameter.

Note: Your fan comes with four pre-installed neoprene noise

isolators.

2-2. read the lead wires from the outlet box down through the hole

in the middle of the hanger bracket.

2-3. Align the slotted holes in the hanger bracket with the pilot holes

you drilled in the wood support structure. For proper alignment

use slotted holes directly across from each other. If you are

installing the fan on an angled ceiling, be sure to orient the hanger

bracket with the large opening towards the ceiling peak.

Note: e isolators should be ush against the ceiling.

2-4. Place a at washer on each of the two 3” screws and pass the

screws through the slotted holes in the hanger bracket into the

pilot holes you drilled.

Tighten the screws into the 9/64” pilot holes; do not use lubricants

on the screws. Do not over tighten.

Flat Washer

3” Screw

Steps 2-2 – 2-4

For Angled Ceilings: Be sure to orient

the hanger bracket with the large

opening towards the ceiling peak.

Hanger

Bracket

Step 2-3 (Angled Ceiling Only)

Isolator

Hunter Fan Company 42005-01 • 01/31/05

42005-01 • 01/31/05 Hunter Fan Company

3 • Assembling and Hanging the Fan

You can assemble your fan for standard or angle mounting as shown

in steps 3-1 – 3-4. For low prole mounting (ceilings less than 8 feet

high), go to steps 3-7 – 3-11 on the next page.

3-1. Remove the label from the standard mounting washer inside the

canopy. Leave the washer in place. (Note: You will not use the

washer included in the parts sack.)

3-2. To assemble fan to hang down from a at or angled ceiling, place

the canopy with washer, and canopy trim ring around the adapter

so that they rest on the fan assembly.

3-3. Feed the wires from the fan through the downrod.

3-4. Screw the downrod into the fan assembly. Tighten the allen head

set screw using the included allen wrench.

CAUTION: e downrod has a special coating on the threads.

Do not remove this coating; the coating prevents the downrod from

unscrewing. Once assembled, do not remove the downrod.

WARNING: Do not carry or lift fan by canopy.

3-5. Raise the fan and place the ball into the hanger bracket.

3-6. Align the notch on the ball with the indent in the hanger bracket.

(Rotate the fan until you hear the notch pop into place.)

Go to 4 • Wiring the Fan.

WARNING: Fan may fall if not assembled as directed in these

installation instructions.

Steps 3-5 – 3-6

Indent

Steps 3-2 – 3-4

Downrod

Canopy

(with Washer)

Canopy

Trim Ring

Set Screw

Canopy

Standard

Mounting

Washer

Step 3-1

Adapter

Label

Hunter Fan Company 42005-01 • 01/31/05

42005-01 • 01/31/05 Hunter Fan Company

3 • Assembling and Hanging the Fan (Low Profile Only)

You can assemble your fan for standard or angle mounting as shown

in steps 3-1 – 3-4 on the previous page. For low prole mounting

(ceilings less than 8 feet high), see steps 3-7 – 3-11 on this page.

3-7. Locate the washer that comes preassembled in the canopy.

Remove the label and discard the washer and label. Locate the set

screw preassembled in the adapter. Remove and discard the set

screw. (Refer to images on previous page.)

3-8. Place the low prole washer from the parts sack into the canopy.

3-9. Place the canopy trim ring and canopy with washer on top of the

fan assembly.

3-10. Align the screw holes in the washer with the holes in the adapter.

Assemble securely with three #8-32 x 1/2” screws.

3-11. Raise the fan and place the hook on the hanger bracket through

the round hole in the rim of the canopy.

WARNING: Fan may fall if not assembled as directed in these

installation instructions.

Steps 3-8 – 3-10

#8-32 x 1/2” Screw

Low Prole Washer

Step 3-11

Step 3-10 (Detail)

Low Prole Washer

(Not Actual Size)

Canopy

Trim Ring

Adapter

Hunter Fan Company 42005-01 • 01/31/05

42005-01 • 01/31/05 Hunter Fan Company

4 • Wiring the Fan

All wiring must be in accordance with national and local electrical

codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a

qualied electrician.

Wall switches are not included. Select an acceptable general-use switch in

accordance with national and local electrical codes.

4-1. Disconnect the power by turning o the circuit breakers to the outlet

box and associated wall switch location.

4-2. Decide how you want to set up the fan and light controls. You can

control the fan and/or lights together or separately using one or two

wall switches. Follow Step 4-3 OR Step 4-4, depending on what you

decide.

Note: If you are not installing a light kit, follow step 4-4.

4-3. If you want to, you can control the fan and light separately using two

wall switches, connect the wires as follows:

• e bare or green ground wire from the ceiling to the green

ground wire from the hanger bracket and the green ground wire

from the fan

• e white wire from the ceiling to the white wire from the fan

• e black wire from the ceiling to the black wire from the fan

• e black/white wire from the fan to the wire for the wall switch

4-4. Alternatively, you can control both fan and light with one switch. To

do so connect the wires as follows:

• e bare or green ground wire from the ceiling to the green

ground wire from the hanger bracket and the green ground wire

from the fan

• e white wire from the ceiling to the white wire from the fan

• e black wire from the ceiling to the black and the black/white

wire from the fan

4-5. To connect the wires, hold the bare metal leads together and place a

wire nut over them, then twist clockwise until tight.

CAUTION: Be sure no bare wire or wire strands are visible after

making connections.

4-6. Push all wires and wire nuts back into the hanger bracket.

Wire Nut

Step 4-3

Step 4-4

Hunter Fan Company 42005-01 • 01/31/05

42005-01 • 01/31/05 Hunter Fan Company

5 • Installing the Canopy and Canopy Trim Ring

5-1. Partially install two canopy screws (about 2 full turns) in the

hanger bracket.

5-2. Raise the canopy over the hanger bracket (For low pro le

installations, you will need to remove the canopy from the hook

 rst). Align partially installed screws with key slots in canopy.

5-3. Twist canopy clockwise to secure.

5-4. Install third canopy screw in round hole on canopy. Securely

tighten all three screws.

5-5. Using both hands, push the canopy trim ring up to the top of the

canopy.  e canopy trim ring will snap and lock into place.

Should you need to remove the canopy

trim ring, follow these steps:

1. Locate the tab indicators, small

bumps on top of tabs.

2. Press  rmly on opposite sides of the

ring towards the canopy.  e tabs

will  ex out releasing the trim ring

from the canopy

Steps 5-1 – 5-2

Canopy Trim

Ring

Canopy

Hanger Bracket

Step 5-3

Canopy

Screw

Steps 5-4 – 5-5

Hunter Fan Company 42005-01 • 01/31/05

42005-01 • 01/31/05 Hunter Fan Company

6 • Assembling the Blades

Hunter fans use several styles of fan blade irons (brackets that hold the

blade to the fan).

6-1. Your fan may include blade grommets. If your fan has grommets,

insert them by hand into the holes on the blades.

6-2. Attach each blade to a blade iron using three blade assembly

screws. If you used grommets, the blades may appear slightly loose

after screws are tightened. is is normal.

6-3. Remove the blade mounting screws and rubber shipping bumpers

from the motor.

Note: In order to attach each blade, you will need to rotate the motor

until the two screw holes for the blade are visible through the cutaway.

6-4. For each blade, insert one blade mounting screw through the

blade iron, and attach lightly to the fan. Insert the second blade

mounting screw, then securely tighten both mounting screws.

Step 6-1 (Detail)

Blade Assembly

Screws

Use with grommet

Use without grommet

Grommet

Blade

Mounting

Screw

Steps 6-1 – 6-2

Step 6-4

Hunter Fan Company 42005-01 • 01/31/05

42005-01 • 01/31/05 Hunter Fan Company

7 • Installing the Switch Housing

7-1. Connect the upper plug connector from the motor to the lower

plug connector in the switch housing assembly.

Note: Both plug connectors are polarized and will only t together

one way. Make sure the connectors are properly aligned before

connecting them. Incorrect connection could cause improper

operation and damage to the product.

7-2. To attach the switch housing, thread the screws through the side

holes of the mounting plate and tighten them securely.

7-3. read the nial with rod (from the sack parts) through the switch

housing cap and into the switch housing.

7-4. Tighten the nial.

Note: You can customize your Hunter fan with a number of accessory

light kits.

Plug

Connector

Switch

Housing

Switch

Housing

Cap

Finial

Step 7-1 – 7-4

Side Holes

Hunter Fan Company 42005-01 • 01/31/05

42005-01 • 01/31/05 Hunter Fan Company

8 • Operating and Cleaning Your Ceiling Fan

8-1. Turn on electrical power to the fan.

8-2.  e fan pull chain controls power to the fan.  e pull chain has

four settings in sequence: High, Medium, Low and O .

• Pull the chain slowly to change settings.

• Release slowly to prevent the chain from recoiling into the

blades.

•  e chain uses a breakaway connector that separates if the

chain is jerked. If this happens, simply reinsert the chain into

the connector.

8-3. Ceiling fans work best by blowing air downward (counterclockwise

blade rotation) in warm weather to cool the room with a direct

breeze. In winter, having the fan draw air upward (clockwise blade

rotation) will distribute the warmer air trapped at the ceiling

around the room without causing a draft.

8-4. For cleaning  nishes, use a soft brush or lint-free cloth to prevent

scratching. A vacuum cleaner brush nozzle can remove heavier

dust. Remove surface smudges or accumulated dirt and dust using

a mild detergent and a slightly dampened cloth. You may use

an artistic agent, but never abrasive cleaning agents as they will

damage the  nish.

8-5. Clean the blades in the same manner as the fan  nish. You can

also remove the blades and clean them in the dishwasher.

In warm weather, use

downward air  ow pattern

In cold weather, use upward

air  ow pattern

To Change Air ow Direction

Turn the fan o and let it come to a complete

stop. Slide the reversing switch on the fan to the

opposite position. Restart fan.

Reversing

Switch

Hunter Fan Company 42005-01 • 01/31/05

42005-01 • 01/31/05 Hunter Fan Company

9 • Troubleshooting

Problem: Nothing happens; fan does not move.

1. Turn power on, replace fuse, or reset breaker.

2. Loosen canopy, check all connections according to the wiring the

fan section.

3. Check the plug connection in the switch housing.

4. Push motor reversing switch  rmly up or down to ensure that the

switch is engaged.

5. Pull the pull chain to ensure it is on.

6. Remove the shipping bumpers.

Problem: Noisy operation.

1. Tighten the blade bracket screws until snug.

2. Check to see if the blade is cracked. If so, replace all the blades.

Problem: Excessive wobbling.

1. If your fan wobbles when operating, use the enclosed balancing kit

and instructions to balance the fan.

2. Tighten all blade iron screws.

3. Turn power o , support fan very carefully, and check that the

hanger ball is properly seated.

If you need parts or service assistance, please call

888-830-1326 or visit us at our WEB site at

http://www.hunterfan.com.

Hunter Fan Company

2500 Frisco Avenue

Memphis, Tennessee 38114

Hunter Fan 28450 Owner's manual

Brand: Hunter Fan

Model: 28450

Type: Owner's manual

Download PDF

report

Hunter Fan 28450 Owner's manual

Hunter Fan 28450 Owner's manual

Related papers

Other documents