Digitus DN-8109 Datasheet

Category
Network media converters
Type
Datasheet
Features
n Compliant with IEEE802.3z Gigabit Ethernet
Standard
n Compliant with Fiber Channel 100-SM-LC-L
standard
n Industry standard small form pluggable (SFP)
package
n Simplex SC connector
n Differential LVPECL inputs and outputs
n Single power supply 3.3V
n TTL signal detect indicator
n Hot Pluggable
n Class 1 laser product complies with EN 60825-1
Ordering Information
PART NUMBER TX/RX INPUT/OUTP
UT
SIGNAL
DETECT
TEMPERATURE
LD Type Distance
LS38-C3S-TC-N-K3
1310/1550 AC/AC TTL
0
°
C to 70
°
C
1310 FP 10km
LS38-C3S-TI-N-K3
1310/1550 AC/AC TTL
-40
°
C to 85
°
C
1310 FP 10km
Absolute Maximum Ratings
PARAMETER SYMBO
L
MIN MAX UNITS NOTE
Storage Temperature
T
S
-40
85
°
C
Supply Voltage
Vcc
-0.5
4.0 V
Input Voltage
V
IN
-0.5
Vcc
V
Output Current
I
o
--- 50 mA
Operating Current
I
OP
--- 400 mA
Recommended Operating Conditions
PARAMETER SYMBOL
MIN MAX UNITS NOTE
0 70 LS38-C3S-TC-N-K3
Case Operating Temperature
T
C
-40 85
°
C
LS38-C3S-TI-N-K3
Supply Voltage
Vcc
3.1 3.5 V
Supply Current
I
TX
+ I
RX
--- 250 mA
Transmitter Electro-optical Characteristics
Vcc = 3.1 V to 3.5 V, T
C
= 0
°
C to 70
°
C (-40
°
C to 85
°
C)
PARAMETER SYMBOL MIN TYP. MAX UNITS NOTE
Output Optical Power
9/125
m
m fiber
P
out
-9
---
-3
dBm Average
Extinction Ratio
ER
9 --- --- dB
Center Wavelength
l
C
1270 1310 1355 nm
Spectral Width (RMS)
D
l
--- --- 2.5 nm
Rise/Fall Time, (20-80%)
T
r
,
f
--- --- 260 ps
Relative Intensity Noise
RIN
--- ---
-120
dB/Hz
Total Jitter
TJ
--- --- 227 ps
Output Eye Compliant with IEEE802.3z
Max. P
out
TX-DISABLE Asserted
P
OFF
--- ---
-45
dBm
Differential Input Voltage
V
DIFF
0.4 --- 2.0 V
Receiver Electro-optical Characteristics
Vcc = 3.1 V to 3.5 V, T
C
= 0
°
C to 70
°
C
PARAMETER SYMBOL
MIN TYP. MAX UNITS NOTE
Optical Input Power-maximum
P
IN
-1 --- --- dBm
BER < 10
-
12
Optical Input Power-minimum
(Sensitivity)
P
IN
--- ---
-21
dBm
BER < 10
-
12
Operating Center Wavelength
l
C
1480 --- 1580 nm
Optical Return Loss
ORL
14 --- --- dB
l=1480~1580nm
Optical isolation
ISO --- --- -40 dB
l=1480~1580nm
Signal Detect-Asserted
P
A
--- ---
-21
dBm
Signal Detect-Deasserted
P
D
-35
--- --- dBm
Differential Output Voltage
V
DIFF
0.5 --- 1.2 V
Data Output Rise, Fall Time
(20-80%)
T
r, f
--- --- 0.35 ns
Receiver Loss of Signal Output
Voltage-Low
RX_LOS
L
0 --- 0.5 V
Receiver Loss of Signal Output
Voltage-High
RX_LOS
H
2.4 ---
V
CC
V
Block Diagram of Transceiver
LD Drive
&
Fault Sense
DATA
DATA/
TX_DISABLE
TX_FAULT
MOD_DEF
(0)
(1)
(2)
LOS Detect
&
POST-Amp
DATA
DATA/
RX_LOS
PRE.
AMPLIFIER
IC
PD
LD
WDM Filter
OPTICAL
SUB-ASSEMBLIES
Transmitter and Receiver Optical Sub-assembly Section
A 1310 nm InGaAsP laser and an InGaAs PIN photodiode integrate with an WDM filter to form a bi-directional single
fiber optical subassembly (OSA). The laser of OSA is driven by a LD driver IC which converts differential input
LVPECL logic signals into an analog laser driving current. And, The photodiode of OSA is connected to a circuit
providing post-amplification quantization, and optical signal detection.
TX_DISABLE
The TX_DISABLE signal is high (TTL logic 1”) to turn off the laser output.
Receive Loss (RX_LOS)
The RX_LOS is high (logic 1”) when there is no incoming light from the companion transceiver. This signal is normally
used by the system for the diagnostic purpose. The signal is operated in TTL level.
Dimensions
ALL DIMENSIONS ARE 0.2mm UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN MILLIMETERS
SFP host board mechanical layout
L
X
A S
Y
S XY
A
1
X
1
L
A S
X
PIN1
PIN1
A S
B
S
B
S A S
B
S A S
LEGEND
1.PADS AND VIAS ARE CHASSIS GROUND
2.THROUGH HOLES, PLATING OPTIONAL
3.HATCHED AREA DENOTES COMPONENT
AND TRACE KEEPOUT(EXCEPT CHASSIS
GROUND)
4.AREA DENOTES COMPONENT KEEPOUT
(TRACES ALLOWED)
DIMENSIONS ARE IN MILLIMETERS
Unit: mm
Pin Assignment
Pin-Out
PIN 1
PIN 10
PIN 20
PIN 11
Pin Signal Name Description
1
T
GND
Transmit Ground
2
TX_FAULT
Transmit Fault
3
TX_DISABLE
Transmit Disable
4
MOD_DEF (2)
SDA Serial Data Signal
5
MOD_DEF (1)
SCL Serial Clock Signal
6
MOD_DEF (0)
TTL Low
7
RATE SELECT
Open Circuit
8
RX_LOS
Receiver Loss of Signal, TTL High, open collector
9
R
GND
Receiver Ground
10
R
GND
Receiver Ground
11
R
GND
Receiver Ground
12
RX-
Receive Data Bar, Differential PECL, ac coupled
13
RX+
Receive Data, Differential PECL, ac coupled
14
R
GND
Receiver Ground
15
V
CCR
Receiver Power Supply
16
V
CCT
Transmitter Power Supply
17
T
GND
Transmitter Ground
18
TX+
Transmit Data, Differential PCEL, ac coupled
19
TX-
Transmit Data Bar, Differential PCEL, ac coupled
20
T
GND
Transmitter Ground
Eye Safety Mark
The LS3 series singlemode transceiver is a class 1
laser product. It complies with EN 60825-1 and FDA
21 CFR 1040.10 and 1040.11. In order to meet laser
safety requirements the transceiver shall be operated
within the Absolute Maximum Ratings.
Caution
All adjustments have been done at the factory
before the shipment of the devices. No
maintenance and user serviceable part is
required. Tampering with and modifying the
performance of the device will result in voided
product warranty.
Required Mark
Note : All information contained in this document is subject to change without notice.
Class 1 Laser Product
Complies with
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Digitus DN-8109 Datasheet

Category
Network media converters
Type
Datasheet

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI