Black & Decker GT534 Owner's manual

Category
Power tools
Type
Owner's manual
3
ENGLISH
Intended use
Your Black & Decker hedgetrimmer has been designed for
trimming hedges, shrubs and brambles.
This tool is intended for consumer use only.
Safety instructions
Warning! When using mains-powered tools, basic safety
precautions, including the following, should always be
followed to reduce the risk of fire, electric shock, personal
injury and material damage.
Read all of this manual carefully before operating the
tool.
Retain this manual for future reference.
Remove the plug from the socket before carrying out any
adjustment, servicing or maintenance.
Keep work area clean
Cluttered areas and benches can cause accidents.
Consider work area environment
Do not expose the tool to rain. Do not use the tool in damp or
wet conditions. Keep the work area well lit. Do not use the
tool where there is a risk of causing fire or explosion, e.g. in
the presence of flammable liquids and gases.
Keep children away
Do not allow children, visitors or animals to come near the
work area or to touch the tool or mains cable.
Dress properly
Do not wear loose clothing or jewellery, as these can be
caught in moving parts. Preferably wear rubber gloves and
non-slip footwear when working outdoors. Wear protective
hair covering to keep long hair out of the way.
Personal protection
Always use safety glasses. Use a face or dust mask whenever
the operations may produce dust or flying particles.
Hearing protection should be worn.
Guard against electric shock
Prevent body contact with earthed or grounded surfaces
(e.g. pipes, radiators, cookers and refrigerators). Electric safety
can be further improved by using a high-sensitivity (30 mA / 30 mS)
residual current device (RCD).
Do not overreach
Keep proper footing and balance at all times.
Stay alert
Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
Secure workpiece
Use clamps or a vice to hold the workpiece. It is safer and it
frees both hands to operate the tool.
Connect dust extraction equipment
If devices are provided for the connection of dust extraction
and collection facilities, ensure that these are connected and
properly used.
Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches are removed
from the tool before operating the tool.
Extension cables
Before use, inspect the extension cable and replace if
damaged. When using the tool outdoors, only use extension
cables intended for outdoor use. Up to 30 m of Black & Decker
extension cable can be used without loss of power.
Use appropriate tool
The intended use is described in this instruction manual.
Do not force small tools or attachments to do the job of a
heavy-duty tool. The tool will do the job better and safer at the
rate for which it was intended. Do not force the tool.
Warning! The use of any accessory or attachment or
performance of any operation with this tool other than those
recommended in this instruction manual may present a risk of
personal injury.
Check for damaged parts
Before use, carefully check the tool and mains cable for
damage. Check for misalignment and seizure of moving parts,
breakage of parts, damage to guards and switches and any
other conditions that may affect its operation. Ensure that the
tool will operate properly and perform its intended function.
Do not use the tool if any part is damaged or defective. Do not
use the tool if the switch does not turn it on and off. Have any
damaged or defective parts repaired or replaced by an
authorised repair agent. Never attempt any repairs yourself.
Unplug the tool
Unplug the tool when it is not in use, before changing any parts
of the tool, accessories or attachments and before servicing.
Avoid unintentional starting
Do not carry the tool with a finger on the on/off switch.
Be sure that the tool is switched off when plugging in.
Do not abuse cord
Never carry the tool by its cord or pull it to disconnect from the
socket. Keep the cord away from heat, oil and sharp edges.
Store idle tools
When not in use, tools should be stored in a dry, locked up or
high place, out of reach of children.
Maintain tools with care
Keep cutting tools sharp and clean for better and safer
performance. Follow the instructions for maintenance and
changing accessories. Keep handles and switches dry, clean
and free from oil and grease.
Repairs
This tool complies with relevant safety requirements.
Repairs should only be carried out by qualified persons using
original spare parts; otherwise this may result in considerable
danger to the user.
4
ENGLISH
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Additional safety instructions for hedgetrimmers
Wear safety glasses or goggles when operating this
tool.
Wear gloves when operating this tool.
Wear ear protection when operating this tool.
Immediately disconnect the cable from the mains if
it is damaged or cut.
Do not expose the tool to rain or high humidity.
Keep the cable away from the blades while using this
tool.
If you have not used a hedgetrimmer before, preferably
seek practical instruction by an experienced user in
addition to studying this manual.
Never touch the blades while the tool is running.
Never attempt to force the blades to come to a standstill.
Do not put the tool down until the blades have come to a
complete standstill.
Regularly check the blades for damage and wear. Do not
use the tool when the blades are worn or damaged.
Take care to avoid hard objects (e.g. metal wire, railings)
when trimming. Should you accidentally hit any such
object, immediately switch the tool off, unplug it and
check for any damage.
Should the tool start to vibrate abnormally, immediately
switch it off and check for any damage.
If the tool stalls, immediately switch it off. Unplug the
tool before attempting to remove any obstructions.
After use, place the blade sheath supplied over the
blades. Store the tool, making sure that the blade is not
exposed.
Always ensure that all handles and guards are fitted
when using the tool. Never attempt to use an incomplete
tool or a tool with unauthorised modifications.
Never allow children to use the tool.
When operating the extending handle, hold the unit away
from your body and loose clothes.
Be aware of falling debris when cutting the higher sides
of a hedge.
Additional safety instructions for Australia and
New Zealand
This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Handle switch
2. Trigger switch
3. Extending handle
4. Front handle release buttons
5. Rear handle release buttons
6. Blade
7. Blade sheath
This hedgetrimmer has the following features for your benefit:
Dual action blades for reduced vibration.
Laser cut and diamond ground blades for improved
cutting.
Extending handle for cutting the higher sides of hedges.
Use
Changing the position of the extending handle
Warning! Before changing the position of the extending
handle, make sure that the tool is switched off and unplugged.
Rotating the handle into the extended position
(fig. A1 & A2)
Your hedgetrimmer will reach you with the handle in the
forward position. To move the handle into the extended
position, proceed as follows:
Support the underside of the unit with one hand.
Simultaneously press the front handle release buttons (4)
with your thumb and middle finger and rotate the handle
(3) backward with your other hand.
Move the handle fully into the extended position. Make
sure the handle clicks and locks into place.
Rotating the handle into the forward position (fig. B1 & B2)
To move the handle from the extended into the forward
position, proceed as follows:
Support the underside of the unit with one hand.
Simultaneously press the rear handle release buttons (5)
with the thumb and index finger of your other hand and
rotate the handle (3) forward. As you move the handle out
of the extended position you will hear a click.
Move the handle fully into the forward position.
5
ENGLISH
Make sure the handle clicks and locks into the front
handle release buttons (4).
Connecting the tool to the mains
Unless the tool is fitted with a mains cable, you will need to
connect an extension cable to the power inlet.
Connect the female socket of a suitable extension cable
to the power inlet of the tool.
Insert the mains plug into a mains outlet.
Warning! The extension cable must be suitable for outdoor use.
When using a cable reel, always unwind the cable completely.
Switching on and off
Warning! Let the tool work at its own pace. Do not overload.
Carefully guide the cable in order to avoid accidentally
cutting it. A good way to control the cable is by putting it
over your shoulder.
For your safety, this tool is equipped with a double
switching system. This system prevents starting the tool
inadvertently and will only allow operation while holding
the tool with both hands.
Switching on
Warning! Make sure the handle is fully locked in either the
forward or the extended position.
Squeeze the handle switch (1).
Squeeze the trigger switch (2) to start the tool.
Switching off
Release the handle switch (1) or the trigger switch (2).
Warning! Never attempt to lock a switch in the on position.
Hints for optimum use
Start by trimming the top of the hedge. Slightly tilt the
tool (up to 15° relative to the line of cut) so that the blade
tips point slightly towards the hedge (fig. C1). This will
cause the blades to cut more effectively. Hold the tool at
the desired angle and move it steadily along the line of
cut. The double-sided blade allows you to cut in either
direction.
In order to obtain a very straight cut, stretch a piece of
string along the length of the hedge at the desired height.
Use the string as a guideline, cutting just above it.
In order to obtain flat sides, cut upwards with the growth.
Younger stems move outwards when the blade cuts
downwards, causing shallow patches in the hedge.
With the handle in the extended position the tool can be
used to cut the high sides of the hedge. Move the tool
side to side in a 40° arc (fig. C2).
Take care to avoid any foreign objects. Especially avoid
hard objects such as metal wire and railings, as these
could damage the blades.
Regularly oil the blades.
Guidelines for trimming (UK & Ireland)
Trim hedges and shrubs with seasonal leaves (new leaves
every year) in June and October.
Trim evergreens in April and August.
Trim conifers and other fast growing shrubs every six
weeks from May until October.
Guidelines for trimming (Australia & New Zealand)
Trim hedges and shrubs with seasonal leaves (new leaves
every year) in December and March.
Trim evergreens in September and February.
Trim conifers and other fast growing shrubs every six
weeks from October until March.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
After use, carefully clean the blades. After cleaning, apply
a film of light machine oil to prevent the blades from
rusting.
Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Make sure all the handle release buttons and switches
are free of debris before and after use.
Always store the tool with the handle locked in the
forward position.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Connect the brown lead to the live terminal in the new plug.
Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 5 A.
6
ENGLISH
Troubleshooting
If the tool does not operate correctly, check the following.
Fault Possible cause Action
Tool will not start. Blown fuse. Replace fuse.
Tripped RCD. Check RCD.
Mains lead Check mains
not connected. supply.
Handle not locked. Release handle,
then re-position.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent environmental
pollution and reduces the demand for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Technical data
GT524 GT535 GT545
Voltage V
AC
230 230 230
(Australia&New Zealand) V
AC
240 240 240
Rated input power W 520 520 520
Blade strokes (no load) min
-1
1,450 1,450 1,450
Blade length cm 43 53 63
Blade gap mm 23 23 23
Blade brake time s < 1,0 < 1,0 < 1,0
Weight (excl. supply cord) kg 3.0 3.3 3.5
EC declaration of conformity
GT524/GT535/GT545
Black & Decker declares that these products conform to:
98/37/EC, 89/336/EEC, 73/23/EEC, EN 50144, EN 55014,
EN 61000, 2000/14/EC,
Hedgetrimmer 520 W, Annex V
L
pA
(sound pressure): 82 dB(A), L
WA
(acoustic power) 96 dB(A),
L
WA
(guaranteed) 98 dB(A), hand/arm weighted vibration < 2.5 m/s
2
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
1-7-2006
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair wear
and tear or replace such products to ensure minimum
inconvenience to the customer unless:
The product has been used for trade, professional or hire
purposes;
The product has been subjected to misuse or neglect;
The product has sustained damage through foreign
objects, substances or accidents;
Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com
Please visit our website www.blackanddecker.co.uk to
register your new Black & Decker product and to be kept up to
date on new products and special offers. Further information
on the Black & Decker brand and our range of products is
available at www.blackanddecker.co.uk
59
TYP
1
WWW.2helpU.com 11 - 07 - 03E13378
GT524 - GT534 - GT535 - GT545
22
21
20
19
23
11
12
13
38
16
15
14
4
5
2
9
10
7
2
5
3
8
6
1
26
17
31
29
24
25
28
27
32
36
32
33
35
34
39
37
30
41
40
63
koneesi?
E›Ó·È ÙÔ ÂÚÁ·ÏÂ›Ô ·˘Ùfi Ë
ÚÒÙË Û·˜ ·ÁÔÚ¿?
Yes
Ja
Oui
Si
Ja
Sim
Ja
Ja
Ja
Kyllä
¡·È
No
Nein
Non
No
Nee
No
Não
Nej
Nei
Nej
Ei
√¯È
Dealer address
Händleradresse
Cachet du revendeur
Indirizzo del
rivenditore
Adres van de dealer
Dirección del detallista
Morada do
revendedor
Återförsäljarens adress
Forhandlerens adresse
Forhandler adresse
Jälleenmyyjän osoite
¢È‡ı˘ÓÛË ·ÓÙÈÚÔÛÒÔ˘
..........................................................................
..........................................................................
Cat. no.:
Is this tool a gift?
Ist dieses Gerät ein
Geschenk?
S’agit-il d’un cadeau?
Si tratta
di un regalo?
Kreeg u de machine als cadeau?
¿Ha recibido usted esta herramienta como
regalo?
Recebeu esta ferramenta como
presente?
Är verktyget en gåva?
Er verktøyet en gave?
Er verktøjet en gave?
Onko kone lahja?
∆Ô ÂÚÁ·ÏÂ›Ô Â›Ó·È ‰ÒÚÔ?
Yes
Ja
Oui
Si
Ja
Sim
Ja
Ja
Ja
Kyllä
¡·È
No
Nein
Non
No
Nee
No
Não
Nej
Nei
Nej
Ei
√¯È
Is this tool your first purchase?
Ist dieses
Gerät ein Erstkauf?
Est-ce un 1er achat?
Questo prodotto è il suo primo acquisto?
Is
deze machine uw eerste aankoop?
¿Es esta
herramienta la primera de este tipo?
Esta ferramenta é a sua primeira compra?
Är detta ditt första B&D-verktyg?
Er dette ditt
første B&D verktøy?
Er dette dit første B&D
verktøj?
Onko tämä ensimmäinen B&D-
Dealer address Date of purchase
Händleradresse Kaufdatum
Cachet du revendeur Date d’achat
Indirizzo del rivenditore Data d’acquisto
Adres van de dealer Aankoopdatum
Dirección del detallista Fecha de compra
Morada do revendedor Data de compra
Återförsäljarens adress Inköpsdatum
Forhandlerens adresse Innkjøpsdato
Forhandler adresse Indkøbsdato
Jälleenmyyjän osoite Ostopäivä
¢È‡ı˘ÓÛË ·ÓÙÈÚÔÛÒÔ˘ ∏ÌÂÚÔÌËÓ›· ·ÁÔÚ¿˜
Name
Name
Nom
Nome
Naam
Nombre
Nome
Namn
Navn
Navn
Nimi
√ÓÔÌ·:
..........................................................................
Address
Adresse
Adresse
Indirizzo
Adres
Dirección
Morada
Adress
Adresse
Adresse
Osoite
¢È‡ı˘ÓÛË:
..........................................................................
..........................................................................
Town
Ort
Ville
Cittá
Plaats
Ciudad
Localidade
Ort
By
By
Paikkakunta
¶fiÏË:
..........................................................................
Postal code
Postleitzahl
Code postal
Codice postale
Postcode
Código
Código postal
Postnr.
Postnr.
Postnr.
Postinumero
∫ˆ‰ÈÎfi˜
..........................................................................
Data protection act: Tick the box if you prefer
not to receive further information.
Bitte
ankreuzen, falls Sie keine weiteren
Informationen erhalten möchten.
Si vous ne
souhaitez pas recevoir d’informations, cochez
cette case.
Barrate la casella se non
desiderate ricevere informazioni.
A.u.b. dit vakje aankruisen indien u geen
informatie wenst te ontvangen.
Señale en la casilla sino quiere recibir
información.
Por favor, assinale com uma cruz
se não desejar receber informação.
Vänligen
kryssa för i rutan om Ni inte vill ha information.
Vennligst kryss av dersom du ikke ønsker
informasjon.
Venligst sæt kryds i ruden
såfremt De ikke måtte ønske at modtage
information.
Merkitkää rasti ruutuun, mikäli ette halua
vastaanottaa informaatiota.
¶·Ú·Î·Ï›ÛÙ ӷ ÛËÌÂÈÒÛÂÙ ¿Ó
‰ÂÓ ı¤ÏÂÙ ӷ ¿ÚÂÙ ÏËÚÔÊÔڛ˜.
64
GUARANTEE CARD
GARANTIEKARTE
CARTE DE GARANTIE
TAGLIANDO DI GARANZIA
GARANTIEKAART
TARJETA DE GARANTÍA
CARTÃO DE GARANTIA
GARANTIBEVIS
GARANTI KORT
GARANTI KORT
TAKUUKORTTI
∫∞ƒ∆∞ E°°À∏™∏™
Português Por favor, recorte esta parte, coloque-a num envelope selado e
endereçado e envie-o logo após a compra do seu produto para o
endereço da Black & Decker do seu país.
Svenska Var vänlig klipp ur denna del och sänd den i ett frankerat kuvert till
Black & Deckers adress i Ditt land.
Norsk Vennligst klipp ut denne delen umiddelbart etter du har pakket ut
ditt produkt og legg det i en adressert konvolutt til Black & Decker
(Norge) A/S.
Dansk Venligst klip denne del ud og send frankeret til
Black & Decker i dit land.
Suomi Leikkaa irti tämä osa, laita se kuoreen ja postita kuori paikalliseen
Black & Decker osoitteeseen.
EÏÏËÓÈη ¶·Ú·Î·ÏÒ Îfi„ÂÙ ·˘Ùfi ÙÔ ÎÔÌÌ¿ÙÈ Î·È Ù·¯˘‰ÚÔÌ‹Û·ÙÂ
ÙÔ ·Ì¤Ûˆ˜ ÌÂÙ¿ ÙËÓ ·ÁÔÚ¿ ÙÔ˘ ÚÔ˚fiÓÙÔ˜ Û·˜ ÛÙËÓ
‰È‡ı˘ÓÛË Ù˘ Black & Decker ÛÙËÓ EÏÏ¿‰·.
English Please complete this section immediately after the purchase of your
tool and send it to Black & Decker in your country. If you live in
Australia or New Zealand, please register by using the alternative
guarantee card supplied.
Deutsch Bitte schneiden Sie diesen Abschnitt ab, stecken ihn in einen
frankierten Umschlag und schicken ihn an die Black & Decker
Adresse Ihres Landes.
Français Découpez cette partie et envoyez-la sous enveloppe timbrée à
l’adresse de Black & Decker dans votre pays, ceci immédiatement
après votre achat.
Italiano Per favore ritagliate questa parte, inseritela in una busta con
francobollo e speditela subito dopo l’acquisto del prodotto
all’indirizzo della
Black & Decker nella vostra nazione.
Nederlands Knip dit gedeelte uit en zend het direct na aankoop in een
gefrankeerde, geadresseerde envelop naar het adres van Black &
Decker in uw land.
Español Después de haber comprado su herramienta envíe usted, por favor,
esta tarjeta a la central de
Black & Decker en su país.
581173-03 07-06
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

Black & Decker GT534 Owner's manual

Category
Power tools
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI