Dell 780-USFF User manual
- Category
- Wall & ceiling mounts accessories
- Type
- User manual
This manual is also suitable for
1 of 14
Dell™ OptiPlex™ 780-USFF Mounting Bracket
The Dell OptiPlex 780-USFF Mounting Bracket supports the System
in vertical or horizontal orientations.
Under Desk MountWall with Wood Stud Mount
dell.com/regulatory_compliance
User’s Guide
www.dell.com support.dell.com
2 of 14
Hazard Symbols Review
Symbol Signal Word Level of Hazard
NOTE
A NOTE indicates important information that helps you
make better use of your Dell Mounting Bracket.
CAUTION
A CAUTION indicates either potential damage to
hardware or loss of data and tells you how to avoid the
problem.
WARNING
A WARNING indicates either potential for property
damage, personal injury, or death.
ELECTRICAL
An ELECTRICAL indicates an impending electrical hazard
which, if not avoided, may result in personal injury, re
and/or death.
These symbols alert the user about a safety condition that demands attention. All users of the
product should be able to recognize and understand the signi cance of the following safety
hazards if encountered on the product or within product documentation.
Information in this document is subject to change without notice.
© 2009 Dell Inc. All rights reserved. Printed in China.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: and the logo are trademarks of Dell Inc.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims
any proprietary interest in trademarks and trade names other than its own.
Model ARWAL
October 2009 Rev. A00
2 of 14
3 of 14
1 About your Dell OptiPlex 780-USFF Mounting Bracket ...................................................4
2 Setting up your Dell OptiPlex 780-USFF Mounting Bracket .............................................4
3 Speci cations ...............................................................................................................14
4 Finding Information .....................................................................................................14
Contents
1
1
2
2
3
3
4 of 14
About your Dell OptiPlex 780-USFF Mounting Bracket
1
Setting up the Dell OptiPlex 780-USFF Mounting Bracket
2
Under Desk MountWall Mount
Mounting Bracket, System Sleeve, two Lag Screws
Components
NOTE: Refer to the System Instruction Guides, packaged separately.
1 System Mounting Bracket
2 System Sleeve
3 System Chassis (ordered separately)
WARNING: Because surfaces
vary widely and the ultimate
mounting method is out of
DELL’s control, it is imperative
that you consult with an appro-
priate engineering, architectural
or construction professional to
ensure that your DELL mount-
ing solution can support 50 lbs
(23 kg) and is mounted prop-
erly.
2x
M8 x 80 mm
5 of 14
1 Ensure the system sleeve is unlocked, (orange tab will show).
2 Extend the system label carrier.
6 of 14
Under Desk Mount
NOTE: When inserted properly for
wall mount applications, the con-
nections end of the system will not
reach the
edge of
the system
sleeve.
Insert the system into the system
sleeve with the CD end rst.
Insert the system into the system sleeve
with the connections end rst.
CAUTION: Do not reverse the insertion order. The
system must be inserted in the orientation speci ed
to ensure proper functioning of the CD tray!
NOTE: When inserted properly for
under desk mount applications, the
CD end of
the system
will reach
the end of
the system
sleeve.
3 Insert the system into the system sleeve in the orientation appropriate
to the mounting method as illustrated below.
Wood Stud Wall Mount
128
7 of 14
5 Determine the mounting method (Wall or Under Desk), then follow
the appropriate instructions on the pages noted below.
Wall Mount
Steps
Under Desk
Mount Steps
4 Push the system label carrier into the system sleeve, then slide the switch to lock.
CAUTION: Mounting fasteners are not
included with bracket. Use appropriate
fasteners to attach to a solid mounting
surface that can support 50 lbs. (23 kg). At a
minimum, the mounting surface should be
1/2” (1.25 cm) thick wood and mount using
4 metal wood screws (M4 x 12mm).
CAUTION: The provided fasteners are
rated for use with 2 x 4 wood studs,
minimum. Consult an engineering profes-
sional to determine which fasteners are
appropriate based on surface material
and applied load.
Under Desk Mount
Wood Stud Wall Mount
Under Desk
Mount
Wall
Mount
≥ M4 x 12mm
≥ 1/2”
(1.25 cm)
4x
2
1
8 of 14
Wood Stud Wall Mount Steps
NOTE: The following tools are required for installation to the
wall stud: stud nder, measuring tape, pencil, level, safety
glasses, power drill with 3/16” (5mm bit suitable for wood).
Stud Finder
Wall Mount Clearance -
Back View
Ceiling
Ceiling
≥6.0” (152.4 mm)
≥8.0” (203.2 mm)≥13” (330.2 mm)
Wall Mount Clearance -
Front View
≥3.33” (85 mm)
Left Wall
Left Wall
Right Wall
Right Wall
≥2.45” (62.2 mm)
≥2.28” (58 mm)
Ø 5 mm (3/16”)
6 Attach the mounting bracket to the wood stud.
a
de
c
f
b
9 of 14
M8 x 80 mm
CAUTION: Make sure the wall mount bracket is
level, ush and snuggly tted to the wall surface.
Stud Finder
Lower the system onto the
wall-mounted bracket.
2x
Ø 5 mm (3/16”)
2
1
10 of 14
6 Mark the mounting hole locations using the measurements
provided on the next pages.
NOTE: The following tools are required for installation to the desk:
measuring tape, pencil, level.
Under Desk Mount Steps
ab
To remove the system from the mounting bracket:
a Push the quick release tab backward.
b Lift the system upward until it is free of the bracket.
≤
11 of 14
Under Desk Clearance -
during assembly
Under Desk Clearance -
after assembly
≥6.0” (152.4 mm)
≥6.0” (152.4 mm)
≥6.0” (152.4 mm)
≤4.25” (108 mm)
≤4.25” (108 mm)
≤ .5” (12.7 mm)
≤ .5” (12.7 mm)
≥6.0” (152.4 mm)
Wall / Desk
Wall / Desk
Wall / Desk
Wall / Desk
Edge of Desk
Edge of Desk
12 of 14
b Slide the system into place on the desk-mounted bracket.
a Mount the bracket underneath the desk.
CAUTION: Mounting fasteners are not
included with bracket. Use appropriate
fasteners to attach to a solid mounting
surface that can support 50 lbs. (23 kg).
At a minimum, the mounting surface
should be 1/2” (1.25 cm) thick wood and
mount using 4 metal wood screws
(M4 x 12mm).
Under Desk Clearance
≥6.0” (152.4 mm)
≥6.0” (152.4 mm)
≤4.25” (108 mm)
Wall / Desk
Wall / Desk
Edge of Desk
CAUTION: Make sure the wall mount bracket is
level, ush and snuggly tted to the wall surface.
≥ M4 x 12mm
≥ 1/2”
(1.25 cm)
4x
CAUTION: The system should have at least 6” (152.4 mm) of clearance on all
vented sides to permit the air ow required for proper ventilation. Restricting
air ow can damage the equipment or cause overheating.
13 of 14
a
b
To remove the system from the mounting bracket:
a Push the quick release tab upward.
b Slide the system toward the right until it is free of the bracket.
4
3
14 of 14
Speci cations
System Weight Capacity
Dell System: OptiPlex 780-USFF ≤ 7 lbs (3.2 kg)
Temperature
Operating 32°F to 95°F (0°C to 35°C )
Storage -40°F to 149°F (-40°C to +69°C)
Transportation -40°F to 149°F (-40°C to +69°C)
Finding Information
If you need to: See:
Find safety best practices information for your computer,
review Warranty information, Terms and Conditions (U.S.
only), Safety instructions, Regulatory information,
Ergonomics information, and End User Agreement
The safety and regulatory documents that
shipped with your computer and the
Regulatory Compliance Homepage at
www.dell.com/regulatory_compliance.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
Dell 780-USFF User manual
- Category
- Wall & ceiling mounts accessories
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
