2. Computers & electronics
  3. Computer components
  4. Chassis components
  5. Racks
  6. Rack accessories
  7. Chief
  8. NE1D36S
NE1D36S

Chief NE1D36S Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Chief NE1D36S Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What are the important warnings or cautions regarding the Chief NE1D36S?
    What tools will I need to install the Chief NE1D36S?
    If the door is to be attached with the pull-ring handle on the right side, what needs to be done before installing the door?
    What is the most important step when installing the Chief NE1D36S?
INSTALLATION INSTRUCTIONS
NE1D20F
NE1D20P
NE1D20S
E1 and G1 Racks Doors
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
NE1D20-28-36-44/NG1D28-36-44
NE1D20-28-36-44/NG1D28-36-44 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Installation Instructions NE1D20-28-36-44/NG1D28-36-44
3
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
7/16"
OR
OR
A (1)
[Door]
[Perforated]
[Solid]
[Plexiglass]
(NE1D20P shown)
(NE1D20F shown)
(NE1D20S shown)
NE1D20-28-36-44/NG1D28-36-44 Installation Instructions
4
INSTALLATION
IMPORTANT ! : If the door is to be attached with the pull-
ring handle on the right side, the nut and grounding wire
already installed on the door must be removed and
reinstalled on the opposite end of the door before the
door is installed. The grounding wire should be on the
BOTTOM of the installed door. (See Figure 1)
Figure 1
1. Pull down on upper spring handle, and push up on lower
spring handle. (See Figure 2)
Figure 2
2. Insert door into rack, aligning the spring handle ends with
the holes at top and bottom of rack. (See Figure 3)
Figure 3
3. Push spring handle end into rack, and re-latch spring
handle.
Move to
grounding
screw
Move nut and
grounding wire
NOTE: Door will
be flipped before
installation.
(view from back of door)
1
Lower
spring
handle
Upper
spring
handle
(View from back of door)
6
Door
support
Door
Spring
handle end
2
2
Installation Instructions NE1D20-28-36-44/NG1D28-36-44
5
4. Remove and save nut from the grounding lug on rack side
rail. (See Figure 4)
5. Attach grounding wire from door to the grounding lug. (See
Figure 4)
6. Replace and tighten nut onto grounding lug. (See Figure 4)
Figure 4
Figure 5
DANGER: IMPROPER WIRING CAN LEAD TO DEATH
OR SEVERE PERSONAL INJURY! Grounding must be
installed by qualified personnel using a UL Recognized No.
12AWG Green and Yellow grounding wire connected to
grounding lug on rack.
3
5
Add door grounding wire
(front view of rack)
(inside view of door)
Grounding screw and nut
installed at factory
affixed adjacent to grounding terminal.
Earthing symbol IEC 60417 No. 5019
Location of
grounding
lugs
NE1D20-28-36-44/NG1D28-36-44 Installation Instructions
6
Installation Instructions NE1D20-28-36-44/NG1D28-36-44
7
NE1D20-28-36-44/NG1D28-36-44 Installation Instructions
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P 800.582.6480 / 952.894.6280
F 877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P +31 (0)40 2668620
F +31 (0)40 2668615
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
Chief Manufacturing, a products division
of Milestone AV Technologies
8821-002013 Rev01
2011 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
06/11
/