Avaya Bogen Zone Paging Module User manual

Brand: Avaya

Model: Bogen Zone Paging Module

Type: User manual

Avaya Bogen Zone Paging Module empowers its users to extend the capabilities of their paging system significantly. This module grants the ability to incorporate additional paging zones, enhancing the system's reach and effectiveness. With the Zone Paging Module, businesses and organizations can create customized paging solutions tailored to their specific requirements, ensuring efficient and targeted communication.

Before You Start

Zone Paging Module

PEC CODE: 5323-108

COM CODE: 408186039

MODEL: LUPCMZONE

Description

The Zone Paging Module can be added to the LUPCMALL or the LUPCMADD Paging Control System

Assemblies when additional paging zones are required. Each LUPCMALL or LUPCMADD can handle up

to 3 (three) Zone Paging Modules (9 paging zones). Each Zone Paging Module can handle 1-3 paging

zones. If more than 3 Zone Paging Modules (9 paging zones) are needed, please consult your Technical

Support Group.

Page 1 of 2

Module Assembly

1. Remove power from the LUPCMALL or LUPCMADD Paging Control System Assemblies.

2. Remove the LUPCMALL or LUPCMADD Assembly that you will be adding a zone to from its wall or

rack mounting (if already installed).

Package Contents

* Zone Paging Module

* Instruction and Use Manual

To add the Zone Paging Module to either the LUPCMALL or LUPCMADD Paging Control System, follow the instructions below.

IMPORTANT: Refer to Figure

(on the back of this sheet) and the steps below to add the Zone Paging Module to

the LUPCMALL Paging Control System Assembly. Refer to Figure 3 (on the back of this sheet) and the steps

below to add the Zone Paging Module to the LUPCMADD Paging Control System Assembly.

1. Remove the right side bracket of the LUPCMALL or LUPCMADD Paging Control System Assembly by removing the two

screws on the end of the assembled system (this is a Zone Paging Module). Remove the metal bracket.

2. Place the Zone Paging Module to be added to the assembly next to the module on the un-bracketed end of the assembled

system.

3. Plug the ribbon cable connector into the header of the Zone Paging Module (see Figure 1 on the back of this sheet).

NOTE: If the 6-pin connector is installed backwards, the power light on that module (and possibly the entire assembly)

will not light when powered up. To correct this, separate the modules and locate the reversed 6-pin connector

and re-connect it.

4. Plug the 6-pin connector onto its header.

5. Dress the connector cables away from the sheet metal so that they will not get pinched. Push the modules together while

aligning the locking tabs on the top and bottom sides of the left unit with the locking slots on the right unit. At this point, the

left unit will be positioned slightly ahead of the right unit. Slide the left unit back against the right unit until the faces of both units

are even.

6. Secure the two modules together by tightening a screw into the screw clamp tab in the back of the unit. Run the screw in and

out of the screw clamp tab to cut a thread before assembling the modules together.

NOTE: It is usually easier to run the screw in and out of the screw clamp tab and to cut a thread before assembling

the modules together.

7. Secure the right side bracket of the LUPCMALL or LUPCMADD Paging Control System Assembly onto the un-bracketed end

of the Zone Paging Module with the two screws you removed earlier.

Repeat steps 2 - 6 if an additional Zone Paging Module is needed and being added to the

assembled system.

POWER

RD COM

RD A

RD B

ZONE A

ZONE B

ZONE C

OFF ON

TALKBACK

RD C

LOCAL

BGM

ZONE A

ZONE B

ZONE C

LPBGM

VOLUME

LO PWR

HI PWR

OUTPUT

BGM

OUT IN

PCM

ZPM

ZONE A

ZONE B

ZONE C

GLOBL BGM

Issue 1, October 1999

Specifications subject to change without notice.

Part No. 54-2022-01 Printed in Korea 9910

Select Code: 701-000-111

Page 2 of 2

NOTE: For operating instruc-

tions, feature settings, and zone

wiring, please refer to the

LUPCMALL Paging Control

System manual.

SCREW CLAMP

TAB & SLOT

LOCKING

TAB

ALIGN

CONNECTORS

SO LOCKING

RIDGE FACES

HEADER WALL

LOCKING

SLOT

ALIGN .

POLARIZING

TAB IN SLOT

LOCKING

TAB

LOCKING

SLOT

LOCKING

TAB

LOCKING

TAB

LOCKING

SLOT

LOCKING

SLOT

ALIGN

CONNECTORS

SO LOCKING

RIDGE FACES

HEADER WALL

ALIGN .

POLARIZING

TAB IN SLOT

SCREW CLAMP

TAB & SLOT

Figure 3: Adding a

Zone Paging Module

to a PCMADD Paging

Control System

Figure 2: Adding 2

Zone Paging Modules

to a PCMALL Paging

Control System

ALIGN

CONNECTORS

SO LOCKING

RIDGE FACES

HEADER WALL

ALIGN .

POLARIZING

TAB IN SLOT

Figure 1: Connecting to the Assembly

Right Side Bracket

Left Side

Rear Side

of Unit

Avaya Bogen Zone Paging Module User manual

Avaya Bogen Zone Paging Module User manual

Avaya Bogen Zone Paging Module User manual

Related papers

Other documents