Brunton F-ALLDAY-2.0-YL Owner's manual

Type
Owner's manual

This manual is also suitable for

ALL DAY 2.0
HIGH CAPACITY POWER SUPPLY FOR GOPRO®
F-ALLDAY-2.0-BK
F-ALLDAY-2.0-YL
QUICK START GUIDE
COMPATIBLE WITH HERO™, HERO™3+ AND HERO™ 4 MODELS.
THE ALL DAY 2.0 WILL NOT FIT OTHER MODELS. HERO™3 IS COMPATIBLE WHEN
USED WITH HERO™3+ OR HERO™4 CASE. GOPRO®, HERO®,
THE GOPRO® LOGO AND THE GOPRO® BE A HERO LOGO ARE TRADEMARKS OR
REGISTERED TRADEMARKS OF GOPRO®, INC.
BR-Manual-ALLDAY 2.0_5.indd 1 9/8/15 11:40 AM
2
POWER FORWARD
The ALL DAY 2.0 extends the power of your HERO™, HERO™3+ and HERO™ 4 models to
more than 5X the specified run-time of the standard battery alone supplied with
your GOPRO® while still offering the rugged, waterproof* performance your camera
requires.
1. Remove existing GOPRO® case back and travel cover from ALL DAY 2.0 By opening
door and pulling straight down out of brackets. Do not remove pin from door.
2. Snap on ALL DAY 2.0.
3. Attach flat USB cable plug to cameras USB input port using specified mini-USB
outlet depending on camera type (see back diagram below). Attach
opposite end of flat cable to camera’s mini-USB power input port and close case.
Ensure cable is not caught in door when closed.
4. Open side door, press ALL DAY 2.0 power button. Shoot longer .
1. 2. 3. 4.
* This product is waterproof up to 40M. Test battery/case for leaks BEFORE placing GOPRO®
in the case before EVERY use and ensure side access door latch is fully engaged. Brunton
is NOT responsible for camera damage while using Brunton products.
POWER UP
Open ALL DAY 2.0 side access door and press power button to supply power to camera.
Charging indicator LED on camera will light to the status of the battery, red or green.
Press again to power off All Day 2.0.
The ALL DAY 2.0 can charge your smartphone or other USB charged device while
powering your GOPRO® camera at the same time. It can also be used as a convenient,
portable, stand-alone power source so you never have to power down. When used as a
portable power bank, please make sure travel cover is snapped onto the ALL DAY 2.0.
To use, open Patented side access door and plug USB powered device into USB output
port.
3. Micro-USB Input
(Charge ALL DAY 2.0)
1. USB Output
(Charge other devices)
2. Power Button
When closing side door, ensure latch is engaged to create waterproof seal.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To recharge the ALL DAY 2.0, connect micro-USB input cable to a running computer,
USB outlet, or a Brunton portable power device. A solid red light on the battery level
LED indicator indicates that the ALL DAY 2.0 is charging.
BR-Manual-ALLDAY 2.0_5.indd 2 9/8/15 11:40 AM
3
SIDE DOOR:
Micro-USB Input
(Charge ALL DAY 2.0)
USB Output
(Charge other devices)
Power Button
BACK:
USE (2.)USB OUTPUT
FOR HERO™ CAMERA
USE (1.) USB OUTPUT FOR
HERO™ 3 AND 4 SERIES CAMERAS
(3.)USB PLUG STORAGE
WHEN NOT IN USE
1
23
Light Color: Power Level:
RED/OFF >30% (Flashing—Needs charge)
GREEN 30–100%
(Solid light indicates ALL DAY 2.0 is charging)
NOTES AND SPECIFICATIONS:
• Rechargeable lithium-polymer battery: 5000 mAh/18.5WH
• Micro USB Input: 5V/1 A
• USB Output: 5V/2.1 A; Output to camera: 5V/2.1A
WARNING
Read all instructions and warning prior to using this product. Improper use of this
product may result in product damage (including damage to your GOPRO® camera),
excess heat, toxic fumes, fire or explosion, for which damages you (“Purchaser”), and
not Brunton (“Manufacturer”) are responsible.
• Do not short-circuit disassemble or expose to fire.
This product is waterproof up to 40M. Test battery/case for leaks BEFORE placing
GOPRO® in the case before EVERY use and ensure side access door latch is fully
engaged. Brunton is NOT responsible for camera damage while using Brunton
products.
• Do not expose to temperatures greater than 60˚C/140˚F.
• Recycle according to local regulation.
A complete list of tips and troubleshooting is at www.brunton.com.
WARRANTY
Please register your ALL DAY 2.0 by visiting www.brunton.com/Register. Brunton has
taken every effort to ensure years of trouble-free use from your new product. This
product is guaranteed to be free of defect in material and workmanship according to
local regulatory requirements. This product is not subject to guarantee from third-
BR-Manual-ALLDAY 2.0_5.indd 3 9/8/15 11:40 AM
4
parties and is subject to change. Brunton will repair or replace with a new equivalent,
without charge for parts or labor, per Brunton’s discretion. Brunton cannot be held
responsible for accidents, damages or injury occasioned by the use of this product.
Warranty will be rendered invalid if product is damaged by tampering, negligence or
misuse. This warranty relates only to Brunton products and does not cover damage
to any attached products from other manufacturers. This product is waterproof up to
40M. Test battery/case for leaks BEFORE placing GOPRO® in the case before EVERY use
and ensure side access door latch is fully engaged. Brunton is NOT responsible for
camera damage while using Brunton products.
____________________________________________________________________________________
ALLEZ DE LAVANT
Lappareil ALL DAY 2,0 augmente l’autonomie des modèles HERO
MC
, HERO 3+
MC
et HEO
4
MC
jusqu’à plus de 5X la durée de fonctionnement indiquée pour la batterie standard
fournie avec le GOPRO
MC
tout en offrant la même robustesse et la même résistance à
l’eau* que le fonctionnement de cette caméra exige.
1. Enlevez l’arrière du boîtier de l’appareil GOPRO
MC
et la plaque de transport du ALL
DAY 2,0 en ouvrant la porte d’accès et en tirant vers le bas pour la sortir de ses
gonds. N’enlevez pas la goupille de la porte.
2. Fixez le ALL DAY 2,0 par pression
3. Fixez le connecteur plat du câble USB à la borne d’entrée USB de la caméra en
utilisant la sortie mini-USB désignée selon le type de caméra (voir le schéma arrière
ci-dessous). Fixez l’autre extrémité du câble plat à la borne d’entrée mini-USB de
la caméra et refermez le boîtier. Assurez-vous que le câble nest pas coincé dans la
porte lorsque celle-ci est fermée.
4. ENREGISTREZ PLUS LONGTEMPS
1. 2. 3. 4.
* Ce produit résiste à l’eau jusquà une profondeur de 40 mètres. Vérifiez l’étanchéité
de la batterie et du boîtier pour déceler des fuites AVANT de placer la GOPRO
MD
dans le
boîtier et avant CHAQUE utilisation et assurez-vous que le fermoir de la porte d’accès
latérale est bien en place. Brunton N’EST PAS responsable pour des dommages à la
caméra lors de l’utilisation des produits Brunton.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pour recharger le ALL DAY 2,0, branchez le câble micro-USB à un ordinateur en marche,
à une sortie USB ou à un bloc d’alimentation portable Brunton.
PORTE D’ACCÈS LATÉRALE
5
6
7
5. Sortie USB (pour charger d’autres appareils)
BR-Manual-ALLDAY 2.0_5.indd 4 9/8/15 11:40 AM
1900 Taylor Avenue
Louisville, CO, 80027
800-443-4871
BRUNTON.COM
info@bruntongroup.com
GOPRO®, HERO, the GOPRO® logo, and the GOPRO® Be a Hero logo are trademarks or
registered trademarks of GOPRO®, Inc.
BR-Manual-ALLDAY 2.0_5.indd 32 9/8/15 11:40 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Brunton F-ALLDAY-2.0-YL Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI