Brunton All Day 2.0 Owner's manual

ALL DAY 2.0

HIGH CAPACITY POWER SUPPLY FOR GOPRO®

F-ALLDAY-2.0-BK

F-ALLDAY-2.0-YL

QUICK START GUIDE

COMPATIBLE WITH HERO™, HERO™3+ AND HERO™ 4 MODELS.

THE ALL DAY 2.0 WILL NOT FIT OTHER MODELS. HERO™3 IS COMPATIBLE WHEN

USED WITH HERO™3+ OR HERO™4 CASE. GOPRO®, HERO®,

THE GOPRO® LOGO AND THE GOPRO® BE A HERO LOGO ARE TRADEMARKS OR

REGISTERED TRADEMARKS OF GOPRO®, INC.

BR-Manual-ALLDAY 2.0_5.indd 1 9/8/15 11:40 AM

2

POWER FORWARD

The ALL DAY 2.0 extends the power of your HERO™, HERO™3+ and HERO™ 4 models to

more than 5X the specified run-time of the standard battery alone supplied with

your GOPRO® while still offering the rugged, waterproof* performance your camera

requires.

1. Remove existing GOPRO® case back and travel cover from ALL DAY 2.0 By opening

door and pulling straight down out of brackets. Do not remove pin from door.

2. Snap on ALL DAY 2.0.

3. Attach flat USB cable plug to camera’s USB input port using specified mini-USB

outlet depending on camera type (see back diagram below). Attach

opposite end of flat cable to camera’s mini-USB power input port and close case.

Ensure cable is not caught in door when closed.

4. Open side door, press ALL DAY 2.0 power button. Shoot longer .

1. 2. 3. 4.

* This product is waterproof up to 40M. Test battery/case for leaks BEFORE placing GOPRO®

in the case before EVERY use and ensure side access door latch is fully engaged. Brunton

is NOT responsible for camera damage while using Brunton products.

POWER UP

Open ALL DAY 2.0 side access door and press power button to supply power to camera.

Charging indicator LED on camera will light to the status of the battery, red or green.

Press again to power off All Day 2.0.

The ALL DAY 2.0 can charge your smartphone or other USB charged device while

powering your GOPRO® camera at the same time. It can also be used as a convenient,

portable, stand-alone power source so you never have to power down. When used as a

portable power bank, please make sure travel cover is snapped onto the ALL DAY 2.0.

To use, open Patented side access door and plug USB powered device into USB output

port.

3. Micro-USB Input

(Charge ALL DAY 2.0)

1. USB Output

(Charge other devices)

2. Power Button

When closing side door, ensure latch is engaged to create waterproof seal.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

To recharge the ALL DAY 2.0, connect micro-USB input cable to a running computer,

USB outlet, or a Brunton portable power device. A solid red light on the battery level

LED indicator indicates that the ALL DAY 2.0 is charging.

BR-Manual-ALLDAY 2.0_5.indd 2 9/8/15 11:40 AM

3

SIDE DOOR:

Micro-USB Input

(Charge ALL DAY 2.0)

USB Output

(Charge other devices)

Power Button

BACK:

USE (2.)USB OUTPUT

FOR HERO™ CAMERA

USE (1.) USB OUTPUT FOR

HERO™ 3 AND 4 SERIES CAMERAS

(3.)USB PLUG STORAGE

WHEN NOT IN USE

1

23

Light Color: Power Level:

RED/OFF >30% (Flashing—Needs charge)

GREEN 30–100%

(Solid light indicates ALL DAY 2.0 is charging)

NOTES AND SPECIFICATIONS:

• Rechargeable lithium-polymer battery: 5000 mAh/18.5WH

• Micro USB Input: 5V/1 A

• USB Output: 5V/2.1 A; Output to camera: 5V/2.1A

WARNING

Read all instructions and warning prior to using this product. Improper use of this

product may result in product damage (including damage to your GOPRO® camera),

excess heat, toxic fumes, fire or explosion, for which damages you (“Purchaser”), and

not Brunton (“Manufacturer”) are responsible.

• Do not short-circuit disassemble or expose to fire.

• This product is waterproof up to 40M. Test battery/case for leaks BEFORE placing

GOPRO® in the case before EVERY use and ensure side access door latch is fully

engaged. Brunton is NOT responsible for camera damage while using Brunton

products.

• Do not expose to temperatures greater than 60˚C/140˚F.

• Recycle according to local regulation.

A complete list of tips and troubleshooting is at www.brunton.com.

WARRANTY

Please register your ALL DAY 2.0 by visiting www.brunton.com/Register. Brunton has

taken every effort to ensure years of trouble-free use from your new product. This

product is guaranteed to be free of defect in material and workmanship according to

local regulatory requirements. This product is not subject to guarantee from third-

BR-Manual-ALLDAY 2.0_5.indd 3 9/8/15 11:40 AM

4

parties and is subject to change. Brunton will repair or replace with a new equivalent,

without charge for parts or labor, per Brunton’s discretion. Brunton cannot be held

responsible for accidents, damages or injury occasioned by the use of this product.

Warranty will be rendered invalid if product is damaged by tampering, negligence or

misuse. This warranty relates only to Brunton products and does not cover damage

to any attached products from other manufacturers. This product is waterproof up to

40M. Test battery/case for leaks BEFORE placing GOPRO® in the case before EVERY use

and ensure side access door latch is fully engaged. Brunton is NOT responsible for

camera damage while using Brunton products.

____________________________________________________________________________________

ALLEZ DE L’AVANT

L’appareil ALL DAY 2,0 augmente l’autonomie des modèles HERO

MC

, HERO 3+

MC

et HEO

4

MC

jusqu’à plus de 5X la durée de fonctionnement indiquée pour la batterie standard

fournie avec le GOPRO

MC

tout en offrant la même robustesse et la même résistance à

l’eau* que le fonctionnement de cette caméra exige.

1. Enlevez l’arrière du boîtier de l’appareil GOPRO

MC

et la plaque de transport du ALL

DAY 2,0 en ouvrant la porte d’accès et en tirant vers le bas pour la sortir de ses

gonds. N’enlevez pas la goupille de la porte.

2. Fixez le ALL DAY 2,0 par pression

3. Fixez le connecteur plat du câble USB à la borne d’entrée USB de la caméra en

utilisant la sortie mini-USB désignée selon le type de caméra (voir le schéma arrière

ci-dessous). Fixez l’autre extrémité du câble plat à la borne d’entrée mini-USB de

la caméra et refermez le boîtier. Assurez-vous que le câble n’est pas coincé dans la

porte lorsque celle-ci est fermée.

4. ENREGISTREZ PLUS LONGTEMPS

1. 2. 3. 4.

* Ce produit résiste à l’eau jusqu’à une profondeur de 40 mètres. Vérifiez l’étanchéité

de la batterie et du boîtier pour déceler des fuites AVANT de placer la GOPRO

MD

dans le

boîtier et avant CHAQUE utilisation et assurez-vous que le fermoir de la porte d’accès

latérale est bien en place. Brunton N’EST PAS responsable pour des dommages à la

caméra lors de l’utilisation des produits Brunton.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pour recharger le ALL DAY 2,0, branchez le câble micro-USB à un ordinateur en marche,

à une sortie USB ou à un bloc d’alimentation portable Brunton.

PORTE D’ACCÈS LATÉRALE

5

6

7

5. Sortie USB (pour charger d’autres appareils)

BR-Manual-ALLDAY 2.0_5.indd 4 9/8/15 11:40 AM

Page is loading ...

1900 Taylor Avenue

Louisville, CO, 80027

800-443-4871

BRUNTON.COM

info@bruntongroup.com

GOPRO®, HERO, the GOPRO® logo, and the GOPRO® Be a Hero logo are trademarks or

registered trademarks of GOPRO®, Inc.

BR-Manual-ALLDAY 2.0_5.indd 32 9/8/15 11:40 AM

Brunton All Day 2.0 Owner's manual

This manual is also suitable for

Brunton All Day 2.0 Owner's manual

in other languages

Related papers

Other documents