Genius JA280C is a microprocessor control unit designed to operate sliding gates with a power supply of 400V. The device ensures safety and convenience while using the gate. Genius JA280C is equipped with a range of features that enhance the overall functionality of the gate system. It includes an intrinsic anti-crushing safety device and provides the option to use additional safety devices like indicator lights and warning signs to prevent accidents. Additionally, it allows for manual operation in case of an emergency power outage.
Genius JA280C is a microprocessor control unit designed to operate sliding gates with a power supply of 400V. The device ensures safety and convenience while using the gate. Genius JA280C is equipped with a range of features that enhance the overall functionality of the gate system. It includes an intrinsic anti-crushing safety device and provides the option to use additional safety devices like indicator lights and warning signs to prevent accidents. Additionally, it allows for manual operation in case of an emergency power outage.
CENTRALE DI COMANDO A MICROPROCESSORE PER CANCELLI SCORREVOLI 400V
MICROPROCESSOR CONTROL UNIT FOR SLIDING GATES 400V
ARMOIRE DE COMMANDE À MICROPROCESSEUR POUR PORTAILS COULISSANTS 400V
CENTRAL DE MANDO CON MICROPROCESADOR PARA PORTONES CORREDIZOS 400V
MIKROPROZESSOR-STEUEREINHEIT FÜR SCHIEBETORE 400V
ISTRUZIONI PER L’USO - NORME DI INSTALLAZIONE
INSTRUCTIONS FOR USE - DIRECTIONS FOR INSTALLATION
INSTRUCTIONS - REGLES D’INSTALLATION
INSTRUCCIONES PARA EL USO - NORMAS PARA LA INSTALACION
GEBRAUCHSANLEITUNG - ANWEISUNGEN ZUR INSTALLATION
JA280C
AVVERTENZE PER L’INSTALLATORE
OBBLIGHI GENERALI PER LA SICUREZZA
1) ATTENZIONE! È importante per la sicurezza delle persone seguire
attentamente tutta l’istruzione. Una errata installazione o un errato
uso del prodotto può portare a gravi danni alle persone.
2) L ntamente le istruzioni prima di iniziare l’installazione del prodotto.
3) I materiali dell’imballaggio (plastica, polistirolo, ecc.) non devono
essere lasciati alla portata dei bambini in quanto potenziali fonti di
pericolo.
4) Conservare le istruzioni per riferimenti futuri.
5) Questo prodotto è stato progettato e costruito esclusivamente per
l’utilizzo indicato in questa documentazione. Qualsiasi altro utilizzo
non espressamente indicato potrebbe pregiudicare l’integrità del
prodotto e/o rappresentare fonte di pericolo.
6) GENIUS declina qualsiasi responsabilità derivata dall’uso improprio o
diverso da quello per cui l’automatismo è destinato.
7) Non installare l’apparecchio in atmosfera esplosiva: la presenza di gas
o fumi infiammabili costituisce un grave pericolo per la sicurezza.
8) Gli elementi costruttivi meccanici devono essere in accordo con
quanto stabilito dalle Norme EN 12604 e EN 12605.
Per i Paesi extra-CEE, oltre ai riferimenti normativi nazionali, per
ottenere un livello di sicurezza adeguato, devono essere seguite le
Norme sopra riportate.
9) GENIUS non è responsabile dell’inosservanza della Buona Tecnica
nella costruzione delle chiusure da motorizzare, nonché delle
deformazioni che dovessero intervenire nell’utilizzo.
10) L’installazione deve essere effettuata nell’osservanza delle Norme EN
12453 e EN 12445. Il livello di sicurezza dell’automazione deve essere
C+E.
11) Prima di effettuare qualsiasi intervento sull’impianto, togliere l’alimen-
tazione elettrica.
12) Prevedere sulla rete di alimentazione dell’automazione un interrutto-
re onnipolare con distanza d’apertura dei contatti uguale o superiore
a 3 mm. È consigliabile l’uso di un magnetotermico da 6A con
interruzione onnipolare.
13) Verificare che a monte dell’impianto vi sia un interruttore differenzia-
le con soglia da 0,03 A.
14) Verificare che l’impianto di terra sia realizzato a regola d’arte e
collegarvi le parti metalliche della chiusura.
15) L’automazione dispone di una sicurezza intrinseca antischiacciamento
costituita da un controllo di coppia. E' comunque necessario verificar-
ne la sogli di intervento secondo quanto previsto dalle Norme indicate
al punto 10.
16) I dispositivi di sicurezza (norma EN 12978) permettono di proteggere
eventuali aree di pericolo da Rischi meccanici di movimento, come
ad Es. schiacciamento, convogliamento, cesoiamento.
17) Per ogni impianto è consigliato l’utilizzo di almeno una segnalazione
luminosa nonché di un cartello di segnalazione fissato adeguatamen-
te sulla struttura dell’infisso, oltre ai dispositivi citati al punto “16”.
18) GENIUS declina ogni responsabilità ai fini della sicurezza e del buon
funzionamento dell’automazione, in caso vengano utilizzati compo-
nenti dell’impianto non di produzione GENIUS.
19) Per la manutenzione utilizzare esclusivamente parti originali GENIUS.
20) Non eseguire alcuna modifica sui componenti facenti parte del
sistema d’automazione.
21) L’installatore deve fornire tutte le informazioni relative al funziona-
mento manuale del sistema in caso di emergenza e consegnare
all’Utente utilizzatore dell’impianto il libretto d’avvertenze allegato al
prodotto.
22) Non permettere ai bambini o persone di sostare nelle vicinanze del
prodotto durante il funzionamento.
23) Tenere fuori dalla portata dei bambini radiocomandi o qualsiasi altro
datore di impulso, per evitare che l’automazione possa essere azionata
involontariamente.
24) Il transito tra le ante deve avvenire solo a cancello completamente
aperto.
25) L’Utente utilizzatore deve astenersi da qualsiasi tentativo di riparazio-
ne o d’intervento diretto e rivolgersi solo a personale qualificato.
26) Tutto quello che non è previsto espressamente in queste istruzioni
non è permesso
IMPORTANT NOTICE FOR THE INSTALLER
GENERAL SAFETY REGULATIONS
1) ATTENTION! To ensure the safety of people, it is important that you
read all the following instructions. Incorrect installation or incorrect
use of the product could cause serious harm to people.
2) Carefully read the instructions before beginning to install the product.
3) Do not leave packing materials (plastic, polystyrene, etc.) within
reach of children as such materials are potential sources of
danger.
4) Store these instructions for future reference.
5) This product was designed and built strictly for the use indicated in this
documentation. Any other use, not expressly indicated here, could
compromise the good condition/operation of the product and/or be
a source of danger.
6) GENIUS declines all liability caused by improper use or use other than
that for which the automated system was intended.
7) Do not install the equipment in an explosive atmosphere: the presence
of inflammable gas or fumes is a serious danger to safety.
8) The mechanical parts must conform to the provisions of Standards EN
12604 and EN 12605.
For non-EU countries, to obtain an adequate level of safety, the
Standards mentioned above must be observed, in addition to national
legal regulations.
9) GENIUS is not responsible for failure to observe Good Technique in the
construction of the closing elements to be motorised, or for any
deformation that may occur during use.
10) The installation must conform to Standards EN 12453 and EN 12445. The
safety level of the automated system must be C+E.
11) Before attempting any job on the system, cut out electrical power.
12) The mains power supply of the automated system must be fitted with
an all-pole switch with contact opening distance of 3mm or greater.
Use of a 6A thermal breaker with all-pole circuit break is recommended.
13) Make sure that a differential switch with threshold of 0.03 A is fitted
upstream of the system.
14) Make sure that the earthing system is perfectly constructed, and
connect metal parts of the means of the closure to it.
15) The automated system is supplied with an intrinsic anti-crushing safety
device consisting of a torque control. Nevertheless, its tripping threshold
must be checked as specified in the Standards indicated at point 10.
16) The safety devices (EN 12978 standard) protect any danger areas
against mechanical movement Risks, such as crushing, dragging, and
shearing.
17) Use of at least one indicator-light is recommended for every system,
as well as a warning sign adequately secured to the frame structure,
in addition to the devices mentioned at point “16”.
18) GENIUS declines all liability as concerns safety and efficient operation
of the automated system, if system components not produced by
GENIUS are used.
19) For maintenance, strictly use original parts by GENIUS.
20) Do not in any way modify the components of the automated system.
21) The installer shall supply all information concerning manual operation
of the system in case of an emergency, and shall hand over to the user
the warnings handbook supplied with the product.
22) Do not allow children or adults to stay near the product while it is
operating.
23) Keep remote controls or other pulse generators away from children,
to prevent the automated system from being activated involuntarily.
24) Transit through the leaves is allowed only when the gate is fully open.
25) The user must not attempt any kind of repair or direct action whatever
and contact qualified personnel only.
26) Anything not expressly specified in these instructions is not permitted.
CONSIGNES POUR L'INSTALLATEUR
RÈGLES DE SÉCURITÉ
1) ATTENTION! Il est important, pour la sécurité des personnes, de suivre
à la lettre toutes les instructions. Une installation erronée ou un
usage erroné du produit peut entraîner de graves conséquences
pour les personnes.
2) Lire attentivement les instructions avant d'installer le produit.
3) Les matériaux d'emballage (matière plastique, polystyrène, etc.) ne
doivent pas être laissés à la portée des enfants car ils constituent des
sources potentielles de danger.
4) Conserver les instructions pour les références futures.
5) Ce produit a été conçu et construit exclusivement pour l'usage
indiqué dans cette documentation. Toute autre utilisation non
expressément indiquée pourrait compromettre l'intégrité du produit
et/ou représenter une source de danger.
6) GENIUS décline toute responsabilité qui dériverait d'usage impropre ou
différent de celui auquel l'automatisme est destiné.
7) Ne pas installer l'appareil dans une atmosphère explosive: la présence
de gaz ou de fumées inflammables constitue un grave danger pour
la sécurité.
8) Les composants mécaniques doivent répondre aux prescriptions des
Normes EN 12604 et EN 12605.
Pour les Pays extra-CEE, l'obtention d'un niveau de sécurité approprié
exige non seulement le respect des normes nationales, mais également
le respect des Normes susmentionnées.
9) GENIUS n'est pas responsable du non-respect de la Bonne Technique
dans la construction des fermetures à motoriser, ni des déformations
qui pourraient intervenir lors de l'utilisation.
10) L'installation doit être effectuée conformément aux Normes EN 12453
et EN 12445. Le niveau de sécurité de l'automatisme doit être C+E.
11) Couper l'alimentation électrique avant toute intervention sur
l'installation.
12) Prévoir, sur le secteur d'alimentation de l'automatisme, un interrupteur
omnipolaire avec une distance d'ouverture des contacts égale ou
supérieure à 3 mm. On recommande d'utiliser un magnétothermique
de 6A avec interruption omnipolaire.
13) Vérifier qu'il y ait, en amont de l'installation, un interrupteur différentiel
avec un seuil de 0,03 A.
14) Vérifier que la mise à terre est réalisée selon les règles de l'art et y
connecter les pièces métalliques de la fermeture.
15) L'automatisme dispose d'une sécurité intrinsèque anti-écrasement,
formée d'un contrôle du couple. Il est toutefois nécessaire d'en
vérifier le seuil d'intervention suivant les prescriptions des Normes
indiquées au point 10.
Page is loading ...
5
ENGLISH
400/230 V~ (+6 -10%) - 50/60 Hz.
10 W
2KW
500 mA
-20°C +50°C
3
Adjustable using trimmer (from 12 to 120 sec.)
90 x 195 x 250 mm.
IP54
MICROPROCESSOR CONTROL UNIT FOR SLIDING GATES 400V
USER INSTRUCTIONS - INSTALLATION STANDARDS
1. GENERAL FEATURES
Thanks to the high-power performance of its built-in microprocessor, this control unit for sliding gates with three-phased 400V
motor offers a wide number of services and adjustments.
The main settings and operating modes can be defined using dip-switches while time adjustments are performed using the
trimmers installed on the electronic circuit board.
7 built-in LEDS constantly display the status of inputs, outputs in addition to any circuit malfunctions.
2. TECHNICAL FEATURES
Power supply
Absorbed power
Max. motor load
Max. load on accessoies
Ambient temperature
Protection fuses
Operating logic
Opening /closing time
Housing degree of protection
Housing dimensions
Functions selected with dip-switches
Terminal board outputs
Radio control connector
Terminal board inputs
Partial opening time
Pause time
Automatic / Semi-automatic /
Automatic with stop / Step-step with stop
Adjustable using trimmer (from 0 to 120 sec.)
Fixed 10 sec.
Total opening / Partial opening /
Closing photocells / Opening-closing limit switch /
STOP / Mains power supply 400/230 V~
Radio receiver boards molex connector
Accessory power supply 24 V~ / Flasher /
Gate status led / Motor
Operating modes
Closing photocell reaction
3. TERMINAL BOARD M1 M2(HIGH VOLTAGE) CONNECTIONS - DESCRIPTION
3.1 400V POWER SUPPLY
Terminals “1 - 2 - 3” . Connection to power supply network 400V~ 50/60 Hz.
3.2 GEAR UNIT
Terminals “4 - 5 - 6” Connect the three-phased motor to terminals T1 - T2 - T3 or T1 - T3 - T2 according to the installation (on the
right or left hand) of the gear motor onto the gate.
WARNING: The gear motor is in the right-hand version in the wiring already provided for.
4. TERMINAL BOARD M3 (HIGH VOLTAGE) CONNECTIONS - DESCRIPTION
4.1 FLASHER
Terminals “7 - 8” (Phase - Neutral). Use a flasher with an operating voltage of 230 V~(100W. max.). When power is supplied to
the system the flasher will blink to confirm that the unit is properly connected to the electric power supply.
4.2 230V POWER SUPPLY
Terminals “9 - 10” (Phase - Neutral). Connection to 230V~ 50/60 Hz power supply network.
Notes:
1) To install sheaths andelectric cables, use adequate separate rigid and/or flexible tubes to avoid interferences.
2) Always separate the low-voltage accessory connection cables from the 230V~ or 400V~ power supply cables.
Two magnetothermal switches with adequate tripping threshold should be provided for upstream of the equipment
5. TERMINAL BOARD M4 (LOW VOLTAGE) CONNECTIONS - DESCRIPTION
5.1 GATE STATUS LED
Terminals “12-13”. The signal led constantly displays gate status and motion. OFF = gate closed; ON = gate open; SLOW FLASHING
= gate opening; FAST FLASHING = gate closing.
5.2 STOP
Terminals “14-15” (Circuit Normally Closed). The status of this input is signalled by LED 2. This circuit is connected to any device
(e.g. button, pressure switch) which, when a contact is opened, can stop the gate motion. It can be used as a safety device
on the opening motion.
Note: If STOP devices are not connected, jumper connect the input. To install multiple STOP devices, connect the NC contacts
in series.
6
ENGLISH
LEDS
2 - Stop
3 - Pulse A
4 - Pulse B
5 - Photocells
6 - Opening limit switch
7 - Closing limit switch
ON OFF
Control deactivated
Safety devices disabled
Limit switch free
LED 1 Diagnostic
Slow: Correct operation
Fast: Failure in the limit switch circuit
Control activated
Control activated
Limit switch free
Control activated
Control deactivated
Control deactivated
Safety devices enabled
Limit switch occupied
Limit switch occupied
5.3 PULSE A - TOTAL OPENING
Terminals “14-16”. (Circuit Normally Open). The status of this input is signalled by LED 3. This circuit is connected to any device
(e.g. button, radio control, etc.) which, when a contact is closed, generates a gate opening and/or closing pulse.
Note: To install multiple pulse devices connect the contacts in parallel.
5.4 PULSE B - PARTIAL OPENING
Terminals “14-17”. (Circuit Normally Open). The status of this input is signalled by LED 4. This circuit is connected to any device
(e.g. button, radio control, etc.) which, when a contact is closed, generates a gate opening and/or closing pulse. The
opening motion is performed for a fixed time of 10 seconds.
Note: To install multiple pulse devices connect the contacts in parallel.
5.5 CLOSING PROTECTION PHOTOCELLS
Terminals “18-19” (Circuit Normally Closed). The status of this input is signalled by LED 5. This circuit is connected to any safety
device (photocells, pressure switch, detector, etc.) which, when a contact is opened, acts as a safety on the closing motion.
The effect will vary depending on the settings performed using dip-sw 4.
Note: To install multiple safety devices connect the NC contacts in series.
Note: If no safety devices are being used, jumper connect the input.
It is possible to prevent the gate from closing by connecting a 24h timer in series to the closing photocell circuit.
6. TERMINAL BOARD M5 (LOW VOLTAGE) CONNECTIONS - DESCRIPTION
6.1 OPENING LIMIT SWITCH
Terminals “20-21” (Circuit Normally Closed). The status of this input is signalled by LED 6. This circuit is connected to the opening
limit switch.
6.2 CLOSING LIMIT SWITCH
Terminals “21-22” (Circuit Normally Closed). The status of this input is signalled by LED 7. This circuit is connected to the closing
limit switch.
WARNING: In case of wrong or missing connection of the limit switch, the control unit will be inhibited and will signal this status
by the fast flashing of the diagnostic LED 1.
6.3 ACCESSORY POWER SUPPLY
Terminals “23-24”. (24 V~). WARNING: the max. load for the accessories is 500 mA.
7. INSERTING THE REMOTE CONTROL RECEIVER BOARD
The unit is designed to house a single-channel radio-receiver module. To install the module, cut off the electric power supply
and insert the module into the special connector M6 inside the unit.
Then follow the instruction coming along with the radio-receiver to store the remote control settings.
Note: Bold is used to indicate the led condition with the gate at rest.
9. ADJUSTMENTS WITH TRIMMER
9.1 PAUSE
To adjust the pause duration (for automatic operation), use trimmer “B”. The duration can be adjusted from 0 to 120 seconds.
9.2 OPEN/CLOSE
To adjust the duration of the gate opening/closing time, use trimmer “C”. The duration can be adjusted from 12 to 120
seconds. Note: To obtain maximum system efficiency, adjust the opening/closing time so that the electric motor can be fed
for a few seconds after the gate has reached the limit switch.
8. CONTROL LEDS
7
ENGLISH
OPERATING LOGIC
Automatic
Semi-automatic
Automatic with stop
Step-step with stop
2
13
4
OFF
ON
ON
OFF
OFF
OFF
ON
ON
CLOSING PHOTOCELL OPERATION
Stops and reverses the motion
Stops and,when released, reverses the motion
OFF
ON
Note: all adjustments are performed with the control unit switched off and the gate closed.
11. OPERATING LOGIC
GATE
STATUS
PULSE A
(total opening)
PULSE B
(partial opening)
PULSES
PHOTOCELLSSTOP
CLOSED
Opens, pauses and closes Blocks Pulse No effect
OPEN IN
PAUSE
Reset the pause
Blocks Pulse and suspends
the pause
Blocks and reverses or stops
and starts after reset as per
dip-sw 4
Re-opens immediately
No effect. If in partial
opening mode, opens
completely
No effect
OPENING
Blocks
operation
STOPPING
Closes immediately No effect / Blocks Pulse
CLOSING
Anticipates closing 2
seconds after the release
AUTOMATIC
SEMI-AUTOMATIC
AUTOMATIC
WITH STOP
Opens
STEP-STEP
WITH STOP
FUSE PROTECTIVE FUSE PROTECTIVE
F2 = 1A/250V - 5x20
F1 = 500mA/250V - 5x20 F3 = 315mA/250V - 5x20
Transformer
Accessories Logics
12. PROTECTIVE FUSES
10. DIP-SWITCH SETTINGS (SW1)
CLOSED
OPEN IN
PAUSE
CLOSING
OPENING
STOPPING
CLOSED
OPEN IN
PAUSE
CLOSING
OPENING
STOPPING
CLOSED
CLOSING
OPENING
STOPPING
OPEN
No effect
Opens, pauses and closes
Re-opens immediately
Re-closes immediately
Re-closes immediately
No effect / Blocks Pulse
No effect
Blocks
operation
Blocks and reverses or stops
and starts after reset as per
dip-sw 4
Blocks Pulse No effect
Closes immediately
Opens, pauses and closes
Reset the pause
Re-opens immediately
Blocks operation
Closes immediately No effect / Blocks Pulse
Blocks
operation
Blocks and reverses or stops
and starts after reset as per
dip-sw 4
No effect
No effectBlocks Pulse
Blocks Pulse and suspends
the pause
Re-closes immediately
Re-opens immediately
Blocks operation
Closes immediately
Blocks Pulse No effect
Blocks Pulse
Blocks and reverses or stops
and starts after reset as per
dip-sw 4
No effect
No effect / Blocks Pulse
Blocks
operation
8
ENGLISH
13. CONNECTION DIAGRAM
400 V~
50/60 Hz
R
S
T
Flasher
Stop
Gate
status
led
Total
opening
Partial
opening
Other safety
devices
Limit switch
Photocells
External radio
receiver (if the
receiving board
is not used on the
M6 connector)
Three-phased reduction gear
230 V~
50/60 Hz
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Genius JA280C is a microprocessor control unit designed to operate sliding gates with a power supply of 400V. The device ensures safety and convenience while using the gate. Genius JA280C is equipped with a range of features that enhance the overall functionality of the gate system. It includes an intrinsic anti-crushing safety device and provides the option to use additional safety devices like indicator lights and warning signs to prevent accidents. Additionally, it allows for manual operation in case of an emergency power outage.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- italiano: Genius JA280C Istruzioni per l'uso
- français: Genius JA280C Mode d'emploi
- español: Genius JA280C Instrucciones de operación
- Deutsch: Genius JA280C Bedienungsanleitung
Related papers
-
Genius JA450C Operating instructions
-
-
-
-
-
-
-
-
-
