Vivotek FD8166A-N User manual

Rev. 1.0

User’s Manual

FD8166A

Ultra-Mini Dome

Network Camera

2MP • Stylish Design • PoE • Smart Stream II • SNV

VIVOTEK

2 - User's Manual

Table of Contents

Overview

..............................................................................................................................................................

3

Revision History ...............................................................................................................................................3

Read Before Use ..............................................................................................................................................4

Package Contents ............................................................................................................................................4

Symbols and Statements in this Document ...................................................................................................... 5

Physical Description .........................................................................................................................................5

Hardware Installation ........................................................................................................................................ 6

Network Deployment ......................................................................................................................................10

Ready to Use .................................................................................................................................................. 17

Accessing the Network Camera

....................................................................................................................

18

Using Web Browsers ......................................................................................................................................18

Using RTSP Players ....................................................................................................................................... 21

Using 3GPP-compatible Mobile Devices ........................................................................................................ 22

Using VIVOTEK Recording Software .............................................................................................................23

Main Page

.........................................................................................................................................................

24

Client Settings

..................................................................................................................................................

29

Conguration

....................................................................................................................................................

34

System > General settings .............................................................................................................................35

System > Homepage layout ..........................................................................................................................37

System > Logs ...............................................................................................................................................40

System > Parameters ....................................................................................................................................42

System > Maintenance ................................................................................................................................... 43

Media > Image .............................................................................................................................................47

Media > Video ................................................................................................................................................56

Media > Video ................................................................................................................................................57

Media > Audio.................................................................................................................................................64

Network > General settings ............................................................................................................................65

Network > Streaming protocols ....................................................................................................................72

Network > SNMP (Simple Network Management Protocol) ...........................................................................81

Security > User accounts ...............................................................................................................................82

Security > HTTPS (Hypertext Transfer Protocol over SSL) .................................................................83

Security > Access List ..................................................................................................................................90

PTZ > PTZ settings ........................................................................................................................................95

Event > Event settings....................................................................................................................................99

Applications > Motion detection....................................................................................................................113

Applications > Digital input .........................................................................................................................116

Applications > Tampering detection .............................................................................................................117

Applications > Audio detection ...................................................................................................................118

Applications > Package management - a.k.a., VADP (VIVOTEK Application Development Platform) .......120

Recording > Recording settings ..................................................................................................................123

Local storage > SD card management ......................................................................................................... 128

Local storage > Content management .........................................................................................................129

Appendix

........................................................................................................................................................

132

URL Commands for the Network Camera .................................................................................................... 132

VIVOTEK

User's Manual - 3

Technical Specications ........................................................................................................................... 316

Technology License Notice ....................................................................................................................... 317

Electromagnetic Compatibility (EMC) .......................................................................................................318

Overview

VIVOTEK’s FD8166A is an ultra-mini xed dome network camera with a tiny diameter of

only 90 mm. Due to its compact and intelligent design and affordable price, the FD8166A is

an ideal indoor surveillance solution that suits a wide variety of applications, such as retail,

ofce, or boutiques, or to monitor elevators or other public areas.

Equipped with a 2 megapixel Full HD sensor enabling viewing resolution of 1920x1080 at

30 fps, the FD8166A is capable of capturing high-denition images whether in high contrast

or low light environments by deploying WDR and SNV technology. When combined with

VIVOTEK’s Smart Stream II technology, the FD8166A can reduce both bandwidth and

storage consumption by up to 50%* while retaining the same superb image quality as a

Full HD camera.

As an all-in-one camera, the FD8166A is designed for easy installation and equipped

with Power over Ethernet (PoE) functionality, making setup both quick and simple. The

FD8166A is also completely compatible with VIVOTEK’s free 32-channel recording

software. With all of these benefits and more, the FD8166A is a sure bet to fulfill your

surveillance needs.

* Depending on scene being monitored.

Revision History

■ Rev. 1.0: Initial release.

VIVOTEK

4 - User's Manual

Read Before Use

The use of surveillance devices may be prohibited by law in your country. The Network Camera

is not only a high-performance web-ready camera but can also be part of a exible surveillance

system. It is the user’s responsibility to ensure that the operation of such devices is legal before

installing this unit for its intended use.

It is important to first verify that all contents received are complete according to the Package

Contents listed below. Take note of the warnings in the Quick Installation Guide before the Network

Camera is installed; then carefully read and follow the instructions in the Installation chapter to

avoid damage due to faulty assembly and installation. This also ensures the product is used

properly as intended.

The Network Camera is a network device and its use should be straightforward for those who

have basic networking knowledge. It is designed for various applications including video sharing,

general security/surveillance, etc. The Configuration chapter suggests ways to best utilize the

Network Camera and ensure proper operations. For creative and professional developers, the URL

Commands of the Network Camera section serves as a helpful reference to customizing existing

homepages or integrating with the current web server.

Package Contents

■ FD8166A

■ screws

■ Quick Installation Guide

■ Focus adjustment tool

VIVOTEK

User's Manual - 5

Symbols and Statements in this Document

i

INFORMATION: provides important messages or advices that might help prevent

inconvenient or problem situations.

NOTE: Notices provide guidance or advices that are related to the functional integrity of

the machine.

Tips: Tips are useful information that helps enhance or facilitae an installation, function,

or process.

WARNING: or IMPORTANT:: These statements indicate situations that can be

dangerous or hazardous to the machine or you.

Electrical Hazard: This statement appears when high voltage electrical hazards might

occur to an operator.

Physical Description

Inner View

Leave the slide cover in place if you route cables through the bottom

and then through a hole on the ceiling or wall.

RJ-45 Socket

Side View

Release tab

Slide cover

DI+ DI-

Max. is 40V.

Digital input

Lens

Tilt adjustment

screw

Reset button

Screw slot

MicroSD/SDHC/SDXC

card slot

LEDs

VIVOTEK

6 - User's Manual

Hardware Installation

0002D10766AD

XXXXXX

1. Jot down the camera's MAC address for later reference.

1

2

Semi-circular

cut-out

Slide cover

Release tab

1. Use one hand to hold the camera

bottom and another hand to hold the

dome cover. Press the release button.

2. Remove the dome cover.

3. Remove the slide cover if you want to

route cables from the side of camera

instead of a hole on the ceiling or wall.

Remove the strain relief boot if your

Ethernet cable comes with one.

VIVOTEK

User's Manual - 7

Mounting the Network Camera - Ceiling or Wall Mount

4. Use the curved slots on the camera as a template to mark where holes will be drilled on

the ceiling. Drill two holes into the ceiling; and hammer in the plastic anchors.

5. Drill another hole if you want to route cables through the ceiling or wall.

6. Connect and route an Ethernet cable through the ceiling or wall.

7. Attach the Network Camera to the ceiling using two included screws.

Routing hole

position

NOTE:

1. Do not completely tighten the mounting screws

in the screw slots yet. You may need to turn the

camera left or right for a best shooting direction

later.

2. The camera can only be powered by PoE. There

is no DC or AC input connector.

3. As shown on the left, you may also route cable

from the side.

VIVOTEK

8 - User's Manual

VIVOTEK

User's Manual - 9

8. There is a tilt adjustment screw near the lens module. Use a #0, #1, or #2 Phillips

screwdriver to turn the screw and the lens will move upwards or downwards.

WARNING!

Do not use your hands to tune the lens module's tilt angle. Doing so will damage the

delicate tilt mechanism.

Lens UP Lens DOWN

VIVOTEK

10 - User's Manual

Network Deployment

General Connection (without PoE)

Power over Ethernet (PoE)

POW

ER

C

O

LL

I

S

ION

L

I

N

K

RE

CEIVE

PARTITIO

N

1

2

3

4

5

PoE Switch

When using a PoE-enabled switch

This Network Camera is PoE-compliant, allowing transmission of power and data via

a single Ethernet cable. Follow the below illustration to connect the camera to a PoE

switch via an Ethernet cable.

When using a non-PoE switch

Use a PoE power injector (optional) to connect between the Network Camera and a

non-PoE switch.

POW

ER

C

O

LL

I

S

ION

L

I

N

K

RECEIVE

PARTITIO

N

1

2

3

4

5

PoE Power Injector

(optional)

Non-PoE Switch

8-2. Tighten the camera's mounting screws

after you change the horizontal shooting

direction.

8-1. You may also tune the camera's

horizontal orientation by turning it along its

curved screw slots.

25°

57°

VIVOTEK

User's Manual - 11

Internet connection via a router

Before setting up the Network Camera over the Internet, make sure you have a router and

follow the steps below.

1. Connect your Network Camera behind a router, the Internet environment is illustrated

below. Regarding how to obtain your IP address, please refer to Software Installation on

page 12 for details.

IP address : 192.168.0.3

Subnet mask : 255.255.255.0

Default router : 192.168.0.1

IP address : 192.168.0.2

Subnet mask : 255.255.255.0

Default router : 192.168.0.1

LAN (Local Area Network)

Router IP address : 192.168.0.1

WAN (Wide Area Network )

Router IP address : from ISP

Cable or DSL Modem

POWER

COLLISION

LINK

RECEIVE

PARTITION

1

2

3

4

5

Internet

2. In this case, if the Local Area Network (LAN) IP address of your Network Camera is

192.168.0.3, please forward the following ports for the Network Camera on the router.

■ HTTP port: default is 80

■ RTSP port: default is 554

■ RTP port for audio: default is 5558

■ RTCP port for audio: default is 5559

■ RTP port for video: default is 5556

■ RTCP port for video: default is 5557

If you have changed the port numbers on the Network page, please open the ports

accordingly on your router. For information on how to forward ports on the router, please

refer to your router’s user’s manual.

3. Find out the public IP address of your router provided by your ISP (Internet Service

Provider).

Use the public IP and the secondary HTTP port to access the Network Camera from the

Internet. Please refer to Network Type on page 56 for details.

Internet connection with static IP

Choose this connection type if you are required to use a static IP for the Network Camera.

Please refer to LAN setting on page 56 for details.

Internet connection via PPPoE (Point-to-Point over Ethernet)

Choose this connection type if you are connected to the Internet via a DSL Line. Please

refer to PPPoE on page 57 for details.

VIVOTEK

12 - User's Manual

Congure the router, virtual server or rewall, so that the router can forward any data com-

ing into a precongured port number to a network camera on the private network, and

allow data from the camera to be transmitted to the outside of the network over the same

path.

From Forward to

122.146.57.120:8000 192.168.2.10:80

122.146.57.120:8001 192.168.2.11:80

... ...

When properly congured, you can access a camera behind the router using the HTTP

request such as follows: http://122.146.57.120:8000

If you change the port numbers on the Network conguration page, please open the ports

accordingly on your router. For example, you can open a management session with your

router to congure access through the router to the camera within your local network.

Please consult your network administrator for router conguration if you have troubles with

the conguration.

For more information with network conguration options (such as that of streaming ports),

please refer to Conguration > Network Settings. VIVOTEK also provides the automatic

port forwarding feature as an NAT traversal function with the precondition that your router

must support the UPnP port forwarding feature.

VIVOTEK

User's Manual - 13

6. Install the "Installation Wizard 2" software utility from your software CD. The program will

search for VIVOTEK Video Receivers, Video Servers or Network Cameras on the same

LAN.

Double-click on the camera’s MAC address to open a browser management session

with the camera.

0002D1730202

00-02-D1-73-02-02 192.168.5.151 FD8168

IW2

Browser

LAN

VIVOTEK

14 - User's Manual

LED Denitions

Item LED status Description

LED Denition

1 Steady Red Powered and system booting, or network

failed

Red LED off Power off

Green LED off Network is disconnected

2 Steady Red and Green LED blinks every 1

sec.

Connected to network

3 Green LED blinks every 1 sec. and RED

LED blinks consecutively every 0.15 sec.

Upgrading rmware

4 Green and RED blink every 0.15 sec, Green

and RED light on, then blink again.

Restoring defaults

5 RED LED is on, Green LED blinks and RED

LED is constantly on.

Status after a reset (network connected)

Green and RED LEDs are constantly on. Status after a reset (network

disconnected)

Hardware Reset

The reset button is used to reset the system or restore the factory default settings.

Sometimes resetting the system can return the camera to normal operation. If the system

problems remain after reset, restore the factory settings and install again.

Reset: Press the recessed reset button. Wait for the Network Camera to reboot.

Restore: Press and hold the reset button until the status LED rapidly blinks. Note that all

settings will be restored to factory default. Upon successful restore, the status LED will

blink green and red during normal operation.

SD/SDHC/SDXC Card Capacity

This network camera is compliant with SD/SDHC/SDXC 16GB / 8GB / 32GB / 64GB and

other preceding standard SD cards.

VIVOTEK

User's Manual - 15

NOTE:

1. The camera is only to be connected to PoE networks without routing to outside plants.

2. For PoE connection, use only UL listed I.T.E. with PoE output.

If your camera should become defocused, you can place the focus adjustment tool

carefully on the lens, and use it to turn the lens clockwise or counter-clockwise to

adjust to the best image focus.

VIVOTEK

16 - User's Manual

9. Use a piece of clean cotton cloth to hold and and install the dome cover.

Install dome cover by aligning the semi-circular cut-out with the release tab. Press on both

ends of the dome cover for it to snap into place. A "Click" sound should be heard when it is

properly installed.

Semi-circular

cut-out

Release

tab

VIVOTEK

User's Manual - 17

Ready to Use

1. A browser session with the Network Camera should prompt as shown below.

2. You should be able to see live video from your camera. You may also install the 32-channel

recording software from the software CD in a deployment consisting of multiple cameras. For

its installation details, please refer to its related documents.

VIVOTEK

18 - User's Manual

Accessing the Network Camera

This chapter explains how to access the Network Camera through web browsers, RTSP players,

3GPP-compatible mobile devices, and VIVOTEK recording software.

Using Web Browsers

Use Installation Wizard 2 (IW2) to access the Network Cameras on LAN.

If your network environment is not a LAN, follow these steps to access the Netwotk Camera:

1. Launch your web browser (e.g., Microsoft

®

Internet Explorer or Mozilla Firefox).

2. Enter the IP address of the Network Camera in the address eld. Press Enter.

3. Live video will be displayed in your web browser.

4. If it is the rst time installing the VIVOTEK network camera, an information bar will prompt as

shown below. Follow the instructions to install the required plug-in on your computer.

NOTE

► For Mozilla Firefox or Chrome users, your browser will use QuickTime to stream the live

video. If you don’t have QuickTime on your computer, please download it rst, then launch

the web browser.

NOTE:

VIVOTEK

User's Manual - 19

► By default, the Network Camera is not password-protected. To prevent unauthorized access,

it is highly recommended to set a password for the Network Camera.

For more information about how to enable password protection, please refer to Security on

page 82.

► If you see a dialog box indicating that your security settings prohibit running ActiveX

®

Controls, please enable the ActiveX

®

Controls for your browser.

1. Choose Tools > Internet Options > Security > Custom Level.

2. Look for Download signed ActiveX

®

controls; select Enable or Prompt. Click OK.

3. Refresh your web browser, then install the ActiveX

®

control. Follow the instructions to

complete installation.

VIVOTEK

20 - User's Manual

•

Currently the Network Camera utilizes a 32-bit ActiveX plugin. You CAN NOT open a

management/view session with the camera using a 64-bit IE browser.

•

If you encounter this problem, try execute the Iexplore.exe program from C:\Windows\

SysWOW64. A 32-bit version of IE browser will be installed.

•

On Windows 7, the 32-bit explorer browser can be accessed from here:

C:\Program Files (x86)\Internet Explorer\iexplore.exe

•

If you open a web session from the IW2 utility, a 32-bit IE browser will be opened.

IMPORTANT:

1. The onscreen Java control can malfunction under the following situations: A PC con-

nects to different cameras that are using the same IP address (or the same camera

running different rmware versions). Removing your browser cookies will solve this

problem.

2. If you encounter problems with displaying the conguration menus or UI items, try dis-

able the Compatibility View on IE8 or IE9.

You may also press the F12 key to open the developer tools utility, and then change the

Browser Mode to the genuine IE8 or IE9 mode.

Tips:

• In the event of plug-in compatibility issues, you may try to uninstall the plug-in that was

previously installed.

Page is loading ...

Vivotek FD8166A-N User manual

Vivotek FD8166A-N User manual

Other documents