Samsung WA16A3Q1 User manual
- Category
- Washing machines
- Type
- User manual
This manual is also suitable for
FUZZY CONTROL
F
uzzy control operates with best washing course
by sensing the washload like artificial intelligence.
TRANSPARENT WINDOW
This Transparent Window is the new concept to solve the curiosity
of users to see inside of washing machine while operation.
While operation, the laundry progress inside of washing machine can be checked by looking
through the transparent window.
BOOMERANG PULSATOR
The Boomerang Pulsator helps water
and detergent to go through fabrics efficiently while providing both the
powerful water action to clean larger and heavier clothes and the gentle
water action to clean all delicates with less wear and tear on clothes.
WATERFALL FLOW
The Waterfall Flow injected from under the pulsator cascades
with full force back into the tub, pushing down any clothes that float right
under the water surface. It is this Waterfall Flow that enables this washing
machine to effectively wash large and heavy items, such as bluejeans and blankets.
MAGIC FILTER
This unique magic Filter ensures that all the lint inside the tub is captured
for top quality filtering results to deliver consistently effective cleaning
results.
1
FEATURES
SW16Z1SP-01248A-gb 4-9-01 10:56 AM Page 1
2
SAFETY INSTRUCTIONS
¤¤
Where an unearthed power cord is not fitted, be
sure that the washer is grounded.
To avoid electrical shock use metal piping for the ground
connection.
Take care not to ground the washer to gas pipes or
telephone cables due to the danger of explosion from
lightning strikes.
¤¤
During spinning, don't put your
hand in the spin basket.
Because the spin basket is rotating at
the high speed, rotating parts may injure
your hand.
¤¤
Openings must not be obstructed by carpeting
when the washing machine is installed on a
carpeted floor.
¤¤
Turn off water taps when the washer is not in
use to avoid water pressure damage to the
pump.
¤¤
To minimize the possibility of electric shock,
unplug this appliance from the power supply or
disconnect the washer at the household
distribution panel by removing the fuse or
switching off the circuit breaker before
attempting any maintenance or cleaning.
¤¤
The appliance is not intended for use by young
children or infirm persons without supervision.
¤¤
Young children should be supervised to ensure
that they do not play with the appliance.
¤¤
If the power supply cord is damaged, it must be
replaced by the manufacturer or its service
agent or a similary qualified person in order to
avoid a hazard.
¤¤
Place clothes evenly into the washer as
unevenly distributed laundry may cause
excessive out-of-balance noise and vibration.
¤¤
Don't use excessively hot water.
(65°C or more)
Plastic parts may be deformed or damaged. Also, clothing
may be deformed or bleached.
¤¤
Before washing, check all pockets.
If nails or pins remain in pockets, they may damage the
washer or clothes.
¤¤
Don’t press the control panel with a sharp
object.
Panel damaged or malfunction may occur.
If the control panel for this
washer is damaged, it must be
replaced by a repair shop appointed
by the manufacturer, as special
purpose tools are required.
¤¤
Do not operate this appliance if it is damaged,
malfunctioning, partially disassembled, or has
missing or broken parts, including a damaged
cord or plug.
¤¤
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of
this or any other appliance.
¤¤
The instructions for use shall specify the
maximum mass or dry cloth in kg, for which
the appliance is designed.
¤¤
If the appliance is supplied from a cord
extension set or electrical portable outlet
device the cord extension set or electrical
portable outlet device should be positioned so
it is not subject to splashing or ingress of
moisture.
WARNING!
To reduce the risk of fire, electric shock, or injury to persons when using your appliance,
take care to adhere to the following precautions.
SW16Z1SP-01248A-gb 4-9-01 10:56 AM Page 2
DESCRIPTION OF PARTS
LID
Be sure to keep the lid
closed during washing
and spinning.
Lint will be collected in the
filter during washing.
When the water pipe is metal,
make sure to cover the end
of the ground wire.
Adjust the length of the
legs when installing
the washer.
MAGIC FILTER
POWER CORD
“BOOMERANG”
PULSATOR
WATER DRAIN HOSE
DRAIN-HOSE
(PUMP)
SOUND ABSORPTION
PANEL
GROUND LEAD
FRONT CONTROL
PANEL
DETERGENT BOX
ADJUSTABLE LEGS
WATER SUPPLY
HOSE(HOT)
WATER SUPPLY HOSE
(COLD)
3
Stainless
SPIN BASKET
SW16Z1SP-01248A-gb 4-9-01 10:56 AM Page 3
4
WATER SUPPLY SELECT BUTTON
As you press this button, the type of water is
selected as follows.
COLD
→ COLD+HOT →HOT → COLD
REMAINING TIME INDICATOR LIGHT
The indicator light shows the remaining time (in
minutes) of each wash cycle.
At the end of the cycle,the power automatically
switches off.
SOAK BUTTON
With every press of this button, the function
changes;
20minutes → 40minutes →60minutes
FUNCTION INDICATOR LIGHT
The function in use indicator shows the current
function as a flashing symbol.
The light goes out at the end of the function.
LEVEL METER
Set it for the water drop to come in the center.
±fiºˆ
DELAY
START
CONTROL PANEL
POWER BUTTON
Press this button once to operate.
Press once again to turn the washer off.
START/HOLD BUTTON
Use to pause and restart the operation.
To change the washing procedure during operation,
press this button to stop, and once again to restart after
changing the procedure.
DELAY START BUTTON
Press this button when delay start washing is needed.
COURSE SELECT BUTTON
With every press of this button, the washing course
changes;
FUZZY → HEAVY DUTY →BEDCLOTHES →
ECONO WASH → WOOL →JEAN
FUNCTION SELECT BUTTON
With every press of each button, the function is simply
changed to Wash, Rinse and Spin.
WATER LEVEL SELECT BUTTON
According to the washload, select the water level ;
MAXIMUM → HIGH →MEDIUM → LOW →
EXTRA LOW → LOW
SW16Z1SP-01248A-gb 4-9-01 10:56 AM Page 4
5
WASHING PROCEDURE
Select the water level from Maximum
to Medium. Cold water is selected.
Selects the best washing course
automatically.
1. Press the POWER Button to"ON".
2. Press the START/HOLD button.
Water level is selected automatically.
Washing,rinsing, and spinning follow.
If you want to pause, press the START/HOLD
button again.You can change the course when paused.
3. Close the lid.
CAUTION . . .
1.Press the power button to "ON".
1.Press the power button to "ON".
3.Press the START/HOLD button.
Washing,rinsing, and spinning follow.
If you want to pause, press the START/HOLD
button again.You can change the course when paused.
-Do not use water above 30°C for WOOL washing.
-Refer to the tag attached on the clothes for washing information.
-Fasten buttons and turn inside out before washing.
-Use the detergent indicated in the laundry.
-When the degree of dirt is extreme, soak the laundry in warm
water for about 10 minutes before pressing the WOOL course
button in order to enhance washing efficiency.
2.Press the course select four times.
4. Close the lid.
FUZZY COURSE
WOOL COURSE
4. Close the lid.
3. Press the START/HOLD button
Water level is selected automatically.
Washing, rinsing, and spinning follow.
If you want to pause, press the START/HOLD
button again.You can change the course when paused.
2. Press the course select button three.
For laundries with light dirt
like towels in a short time.
ECONO WASH COURSE
1.Press the power button to "ON".
4. Close the lid.
3. Press the START/HOLD button
Water level is selected automatically.
Washing, rinsing, and spinning follow.
If you want to pause, press the START/HOLD
button again.You can change the course when paused.
2. Press the course select button once.
HEAVY DUTY COURSE
Before starting washing, check the following;
Connect the water supply hose to the water tap. Leave a tap open.
Plug the power cord in. Make sure to lay down the drain hose.(In case no drain pump)
Put the laundry into the washer and add detergent, too.
Be careful not to overload. Use right detergent for the fabrics you are washing.
Suitable number of Thobe for
laundering is three to five.
THOBE COURSE
SW16Z1SP-01248A-gb 4-9-01 10:56 AM Page 5
Select this course when you have to go out or do something else.
6
FUNCTION BUTTON
MANUAL FUNCTIONS
WASH ONLY
Press the WASH button one.
Press the START/HOLD button once.
Washing goes on for 23 minutes.
When the WASH button is pressed during washing,
the wash time can be changed to between 6 and 30
minutes in duration.
SPIN ONLY
Press the SPIN button once.
Press the START/HOLD button once.
Spin drying goes on for 10 minutes.
When the SPIN button is pressed during spinning,
the spin time can be changed to from 1 to 9 minutes.
RINSE AND SPIN
Press the RINSE and SPIN button once.
Press the START/HOLD button once.
Rinsing and spin drying follow.
When the RINSE and SPIN button is pressed during
working, the rinse times can be changed to between 1
and 5 times in duration.
WASH AND RINSE
Press the WASH and RINSE button once.
Press the START/HOLD button once.
Washing and rinsing go on for 52 minutes.
When the WASH and RINSE button is pressed during
working, the rinse times can be changed to between 1
and 5 times in duration.
RINSE ONLY
Press the RINSE button once.
Press the START/HOLD button once.
Rinsing goes on for 22 minutes.
When the RINSE button is pressed during rinsing,
the rinse times can be changed to between 1 and 5
times in duration.
4. Close the lid.
1. Press the power button to "ON".
2. Press the DELAY START button once.
You may change the delay start time with
use the DEALY START button.
(from 3 hours to 19 hours)
The washing finishes by the time you reserved.
3. Press the START/HOLD button and put the
proper amount of detergent into tub.
DELAY START COURSE
SOAK FUNCTION
Select the course(Press the course button).
➜ FUZZY → HEAVY DUTY →BEDCLOTHES →
ECONO WASH → WOOL →JEAN
Select the time(Press the SOAK button).
➜ 20 minutes
→
40 minutes
→
60 minutes
Press the START/HOLD button once.
Water level is selected automatically.
Washing, rinsing, and spinning follow.
SW16Z1SP-01248A-gb 4-9-01 10:56 AM Page 6
7
1.Remove the adaptor from
the water supply hose.
2.First,using a "+" type screw
driver, loosen the four
screws on the adaptor.
Next,take the adaptor and
turn part(b) following the
arrow for gap about 5mm
between them.
3.Connect adaptor to the
water tap by tightening the
screws firmly.
Then,turn part (b) following
the arrow and put (a) and
(b)together.
5.Connect the other end of
the water supply hose to the
inlet water valve at the back
of the washer.
Screw the hose clockwise
all the way in.
If the water tap is a screw
type,assemble a water
supply hose that fits to the
tap as shown.
NOTICE After completing connection,if water leaks from the hose,then repeat the same steps.
Use the most conventional type of faucet for water supply.
In case the faucet is square or too big,remove the spacing ring before inserting the faucet into the adaptor.
INSTALLATION & MAINTENANCE
Leave some space
Maintain at least 10cm between the washer and the wall.
Place the washer on a sturdy flat surface.
If the washer is placed on an uneven or weak surface,
noise or vibration occurs. (Allowable is 1°)
Adjust the legs for even placement.
Never install the washer near water.
Do not place the washer in steamy rooms or where
the washer is directly exposed to rain.Moisture may
destroy the electrical insulation causing an electrical
shock hazard.
Avoid direct sunlight or heaters.
As plastic and electrical components are affected
by direct heat,never place the washer near furnaces,
boilers,etc.Do not place under direct sunlight.
Push front side of Anti-rat cover into
assembling inlet
●
Take off Anti-rat cover, which is
adhered to the rear of the product,
and then assemble it.
●
Install the cover to reduce noise
and prevent any mouse from
entering the system.
When you feel difficult in assembling, take
following action
●
While raising front side of washing
machine upward a little, push Anti-
rat cover forward with your hand in
line with insertion groove. you can
do it easily.
(After finishing the insertion work,
make sure that fixed area at the middle has been firmly
inserted.)
CONNECTING THE WATER SUPPLY HOSE
ENVIRONMENT
ASSEMBLING METHOD OF ANTI-
RAT COVER
4. Connect the water supply hose
to the adaptor. Pull down the
part (c) of the water supply
hose .When the part (c)is
released,the hose is automat-
ically connected to the adaptor
making a 'click' sound.
70~80cm
●
Be sure to join tightly
the drain hose into the
drain-outlet on theback
of the machine.
●
Take out the
cap-hose
and
connect the
outlet-hose.
●
Install the drain hose
in the position of
about 70~80cm
above the ground.
IN CASE OF PUMP DRAINED WASHER
cap-hose
outlet-hose
After pressing the joint ring(a), insert the drain hose(b)
to drain direction.
CONNECTING THE DRAIN HOSE
1
(a)
(b)
Anti-rat cover
SW16Z1SP-01248A-gb 4-9-01 10:56 AM Page 7
HOW TO CLEAN THE FILTER
8
CLEANING THE FILTER NET
LEVELLING
tor.
1. Push the upper part of
the filter and pull in.
2. Open the cover as
shown in the figure.
3. Clean the filter. 4. Close the cover and insert the lower
part of the filter in the basket first and
then push the filter with "click" sound .
1. Place a rag under the washer filter not to wet the floor.
2. Rotate the filter counterclockwise and pull out the filter.
3. Remove dirts and rotate the filter clockwise until it locks in
position.
Adjustment the heigt of the machine
Adjust the legs to level the washer
Be careful not to put in your hand under the legs.
Adjust a waterdrop mark to be in the red
line at the center of the level meter.
●
Open the lid of the machine, and check if
it is levelled properly in the same way of the
picture.
●
There can be a few
differences according to
the models.
Pull the handles located at the
right and left of the front side
and slide off.
Adjust the height of the machine
upward or downward.
When the adjustment
is finished, push the handles
to fix the adjusting legs.
HOW TO PUT THE DETERGENT/RINSE IN
Pull the detergent/rinse box.
Put the detergent as much as the diagram deside
water level indicator, and fill the fiber softner up to
the baseline.
CAUTION :
When to much softner is stored above the
base line,it may flow down at any time.
Detergent Device
Put the detergent
in proportion to
water level
Softner Device
Softner
baseline
Levelling is complete
Level meter
Softner Device
Softner
baseline
SW16Z1SP-01248A-gb 4-9-01 10:56 AM Page 8
FEATURES ............................................................................................1
SAFETY INSTRUCTIONS .....................................................................2
DESCRIPTION OF PARTS....................................................................3
CONTROL PANEL.................................................................................4
WASHING PROCEDURE ......................................................................5
FUZZY COURSE ..............................................................................5
HEAVY DUTY COURSE...................................................................5
ECONO WASH COURSE.................................................................5
WOOL COURSE ..............................................................................5
DELAY START COURSE .................................................................6
MANUAL FUNCTIONS ..........................................................................6
INSTALLATION & MAINTENANCE ......................................................7
ENVIRONMENT................................................................................7
IN CASE OF PUMP-DRAINED WASHER .......................................7
ASSEMBLING METHOD OF ANTI-RAT COVER.............................7
CONNECTING THE DRAIN HOSE .................................................7
CONNECTING THE WATER SUPPLY HOSE .................................7
CLEANING THE FILTER NET ..........................................................8
LEVELLING.......................................................................................8
HOW TO CLEAN THE FILTER.........................................................8
HOW TO PUT THE DETERGENT/RINSE IN ...................................8
TROUBLESHOOTING
SPECIFICATIONS
Before operating the unit, please read this manual
throughly, and retain for future reference.
Washing Machine
Owner’s Instructions
SW16Z1SP
SW16Z1SP-01248A-gb 4-9-01 10:56 AM Page 9
NORMAL CAPACITY
DIMENSIONS
WEIGHT
WATER PRESSURE
WASHING TYPE
MOTOR INPUT
RATING TIME
SPINNING TUB
ROTATING SPEED
PULSATOR
ROTATING SPEED
WATER USAGE
STANDARD
WATER LEVEL
MOTOR MAX
INPUT
280 l
104 rpm
700 rpm
Continue
15minutes
SPECIFICATIONS
IN CASE THE NEED FOR SERVICING ARISES.
Don't hesitate to call any agency nearby with your name, address
and telephone number when anything wrong with your product occurs.
WASHING
SPINING
WASHING
SPINING
WASHING
SPINING
WASHING
SPINING
MAXIMUM 100
l
HIGH 95
l
MEDIUM 85
l
LOW 70
l
EXTRA LOW 46
l
LOWEST 26
l
CODE NO. : DC68-01248A
16Kg
16kg
W640xD698xH945mm
54kg
0.05~0.78 MPa
(0.5 ~ 8.0Kg • f/cm
2
)
Stirring Type
675W
330W
675W
TROUBLESHOOTING
Washing machine won't work
Is the water tap opened?
Is the washer plugged in?
Is the power cut off?
Is there enough water?
Is the water tap opened?
Is the water cut off?
Is the water supply hose or hose
connection clogged?
Is the water tap frozen?
If water is not supplied in 1 hour, a
buzzer will sound, and the remaining
time indicator will show "4E".
Water is not supplied
Spinning does not work
Is the laundry spread out evenly
in the washer?
Is the washer set on a sturdy
flat surface?
Restart after spinning.
If the error sign still indicates,
call agency.
Water is overflowed
Water dose not drain
Is the drain hose down?(No pump)
Is the drain hose frozen?
Is the drain hose clogged?
If the water dose not drain in 15 minutes,
a buzzer will sound,and the remaining
time indicator will show "5E".
SW16Z1SP-01248A-gb 4-9-01 10:56 AM Page 10
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Samsung WA16A3Q1 User manual
- Category
- Washing machines
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI