DeWalt D28143 Owner's manual

Page is loading ...

2

Dansk (oversat fra original brugsvejledning) 3

Deutsch (übersetzt von den originalanweisungen) 16

English (original instructions) 31

Español (traducido de las instrucciones originales) 44

Français (traduction de la notice d’instructions originale) 58

Italiano (tradotto dalle istruzioni originali) 72

Nederlands (vertaald vanuit de originele instructies) 86

Norsk (oversatt fra de originale instruksjonene) 100

Português (traduzido das instruções originais) 113

Suomi (käännetty alkuperäisestä käyttöohjeesta) 127

Svenska (översatt från de ursprungliga instruktionerna) 139

Türkçe (orijinal talimatlardan çevrilmiştir) 152

Ελληνικά (μετάφραση από τις πρωτότυπες οδηγίες) 166

Copyright DEWALT

Page is loading ...

ENGLISH

31

ANGLE GRINDERS

D28142, D28143

Congratulations!

You have chosen a DEWALT tool. Years of

experience, thorough product development and

innovation make DEWALT one of the most reliable

partners for professional power tool users.

Technical Data

D28142 D28143

Voltage V 230 220–240

U.K. & Ireland only V 115 115

Type 3 3

Power input W 1100 1100

No-load/rated speed min

-1

10,000 10,000

Wheel diameter mm 115/125 115

Spindle diameter M14 M14

Weight kg 2.6* 2.6*

* weight includes side handle and guard

L

PA

(sound pressure) dB(A) 91.5 91.5

K

PA

(sound pressure

uncertainty) dB(A) 3 3

L

WA

(sound power) dB(A) 102.5 102.5

K

WA

(sound power

uncertainty) dB(A) 3 3

Vibration total values (triax vector sum) determined according

to EN 60745:

Vibration emission value a

h

disc sanding

a

h,DS

=

m/s²

9.3 9.3

Uncertainty K = m/s²

1.5 1.5

Vibration emission value a

h

surface grinding

a

h,AG

=

m/s²

<

2.5

<

2.5

Uncertainty K = m/s²

1.5 1.5

The vibration emission level given in this information

sheet has been measured in accordance with a

standardised test given in EN 60745 and may be

used to compare one tool with another. It may be

used for a preliminary assessment of exposure.

WARNING: The declared vibration

emission level represents the main

applications of the tool. However if the

tool is used for different applications,

with different accessories or poorly

maintained, the vibration emission may

differ. This may significantly increase the

exposure level over the total working

period.

An estimation of the level of exposure to

vibration should also take into account

the times when the tool is switched off

or when it is running but not actually

doing the job. This may significantly

reduce the exposure level over the total

working period.

Identify additional safety measures to

protect the operator from the effects of

vibration such as: maintain the tool and

the accessories, keep the hands warm,

organisation of work patterns.

Fuses

Europe 230 V tools 10 Amperes, mains

U.K. & Ireland 230 V tools 13 Amperes, in plugs

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and

pay attention to these symbols.

DANGER: Indicates an imminently

hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING: Indicates a potentially

hazardous situation which, if not

avoided, could result in death or

serious injury.

CAUTION: Indicates a potentially

hazardous situation which, if not

avoided, may result in minor or

moderate injury.

NOTICE: Indicates a practice not

related to personal injury which, if

not avoided, may result in property

damage.

Denotes risk of electric shock.

Denotes risk of fire.

ENGLISH

32

EC-Declaration of Conformity

MACHINERY DIRECTIVE

D28142, D28143

DEWALT declares that these products described

under Technical Data are in compliance with:

2006/42/EC, EN 60745-1, EN 60745-2-3.

These products also comply with Directive

2004/108/EC and 2011/65/EU. For more

information, please contact DEWALT at the following

address or refer to the back of the manual.

The undersigned is responsible for compilation of the

technical file and makes this declaration on behalf of

DEWALT.

Horst Grossmann

Vice President Engineering and Product

Development

DEWALT, Richard-Klinger-Straße 11,

D-65510, Idstein, Germany

01.03.2012

WARNING: To reduce the risk of injury,

read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings

and all instructions. Failure to follow

the warnings and instructions may result

in electric shock, fire and/or serious

injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of

electric shock.

b) Avoid body contact with earthed or

grounded surfaces such as pipes,

radiators, ranges and refrigerators. There

is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the

risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

f) If operating a power tool in a damp

location is unavoidable, use a residual

current device (RCD) protected supply.

Use of an RCD reduces the risk of electric

shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use a power tool while

you are tired or under the influence of

drugs, alcohol or medication. A moment of

inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off position before

connecting to power source and/or

battery pack, picking up or carrying the

tool. Carrying power tools with your finger

on the switch or energising power tools that

have the switch on invites accidents.

ENGLISH

33

d) Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotating

part of the power tool may result in personal

injury.

e) Do not overreach. Keep proper

footing and balance at all times. This

enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewellery. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce

dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the

correct power tool for your application.

The correct power tool will do the job

better and safer at the rate for which it

was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the switch

is dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or the battery pack from

the power tool before making any

adjustments, changing accessories, or

storing power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and

tool bits etc., in accordance with these

instructions taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a

qualified repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

ADDITIONAL SPECIFIC SAFETY RULES

Safety Instructions for All Operations

a) This power tool is intended to function

as a grinder, sander, wire brush or cut-off

tool. Read all safety warnings, instructions,

illustrations and specifications provided with

this power tool. Failure to follow all instructions

listed below may result in electric shock, fire

and/or serious injury.

b) Operations such as polishing are not

recommended to be performed with this

power tool. Operations for which the power

tool was not designed may create a hazard and

cause personal injury.

c) Do not use accessories which are not

specifically designed and recommended

by the tool manufacturer. Just because the

accessory can be attached to your power tool,

it does not assure safe operation.

d) The rated speed of the accessory must be at

least equal to the maximum speed marked

on the power tool. Accessories running faster

than their rated speed can break and fly apart.

e) The outside diameter and the thickness of

your accessory must be within the capacity

rating of your power tool. Incorrectly sized

accessories can not be adequately guarded or

controlled.

f) The arbour size of wheels, flanges, backing

pads or any other accessory must properly

fit the spindle of the power tool. Accessories

with arbour holes that do not match the

mounting hardware of the power tool will run

out of balance, vibrate excessively and may

cause loss of control.

g) Do not use a damaged accessory. Before

each use inspect the accessory such as

abrasive wheel for chips and cracks, backing

pad for cracks, tear or excess wear, wire

brush for loose or cracked wires. If power

tool or accessory is dropped, inspect for

damage or install an undamaged accessory.

After inspecting and installing an accessory,

ENGLISH

34

position yourself and bystanders away from

the plane of the rotating accessory and run

the power tool at maximum no-load speed

for one minute. Damaged accessories will

normally break apart during this test time.

h) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety glasses.

As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection must

be capable of stopping flying debris generated

by various operations. The dust mask or

respirator must be capable of filtrating particles

generated by your operation. Prolonged

exposure to high intensity noise may cause

hearing loss.

i) Keep bystanders a safe distance away from

work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken

accessory may fly away and cause injury

beyond immediate area of operation.

j) Hold power tool by insulated gripping

surfaces only, when performing an operation

where the cutting accessory may contact

hidden wiring or its own cord. Cutting

accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and

could give the operator an electric shock.

k) Position the cord clear of the spinning

accessory. If you lose control, the cord may be

cut or snagged and your hand or arm may be

pulled into the spinning accessory.

l) Never lay the power tool down until the

accessory has come to a complete stop. The

spinning accessory may grab the surface and

pull the power tool out of your control.

m) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

n) Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside

the housing and excessive accumulation of

powdered metal may cause electrical hazards.

o) Do not operate the power tool near

flammable materials. Sparks could ignite these

materials.

p) Do not use accessories that require liquid

coolants. Using water or other liquid coolants

may result in electrocution or shock.

FURTHER SAFETY INSTRUCTIONS

FOR ALL OPERATIONS

Causes and Operator Prevention

of Kickback

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush or

any other accessory. Pinching or snagging causes

rapid stalling of the rotating accessory which in turn

causes the uncontrolled power tool to be forced in

the direction opposite of the accessory’s rotation at

the point of the binding.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into the

surface of the material causing the wheel to climb

out or kick out. The wheel may either jump toward

or away from the operator, depending on direction

of the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these

conditions.

Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be

avoided by taking proper precautions as given

below:

a) Maintain a firm grip on the power tool and

position your body and arm to allow you to

resist kickback forces. Always use auxiliary

handle, if provided, for maximum control

over kickback or torque reaction during start

up. The operator can control torque reaction or

kickback forces, if proper precautions are taken.

b) Never place your hand near the rotating

accessory. Accessory may kickback over your

hand.

c) Do not position your body in the area where

power tool will move if kickback occurs.

Kickback will propel the tool in direction

opposite to the wheel’s movement at the point

of snagging.

d) Use special care when working corners,

sharp edges etc. Avoid bouncing and

snagging the accessory. Corners, sharp

edges or bouncing have a tendency to snag the

rotating accessory and cause loss of control or

kickback.

e) Do not attach a saw chain woodcarving

blade or toothed saw blade. Such blades

create frequent kickback and loss of control.

ENGLISH

35

Safety Warnings Speciﬁ c for

Grinding and Abrasive Cutting-Off

Operations

a) Use only wheel types that are recommended

for your power tool and the specific guard

designed for the selected wheel. Wheels for

which the power tool was not designed cannot

be adequately guarded and are unsafe.

b) The guard must be securely attached to the

power tool and positioned for maximum

safety, so the least amount of wheel is

exposed towards the operator. The guard

helps to protect the operator from broken wheel

fragments and accidental contact with wheel

and sparks that could ignite clothing.

c) Wheels must be used only for recommended

applications. For example: do not grind with

the side of cut-off wheel. Abrasive cut-off

wheels are intended for peripheral grinding, side

forces applied to these wheels may cause them

to shatter.

d) Always use undamaged wheel flanges

that are of correct size and shape for your

selected wheel. Proper wheel flanges support

the wheel thus reducing the possibility of wheel

breakage. Flanges for cut-off wheels may be

different from grinding wheel flanges.

e) Do not use worn down wheels from larger

power tools. Wheel intended for larger power

tool is not suitable for the higher speed of a

smaller tool and may burst.

Additional Safety Warnings Speciﬁ c

for Abrasive Cutting-Off Operations

a) Do not “jam” the cut-off wheel or apply

excessive pressure. Do not attempt to make

an excessive depth of cut. Overstressing the

wheel increases the loading and susceptibility to

twisting or binding of the wheel in the cut and

the possibility of kickback or wheel breakage.

b) Do not position your body in line with and

behind the rotating wheel. When the wheel,

at the point of operations, is moving away from

your body, the possible kickback may propel the

spinning wheel and the power tool directly at

you.

c) When wheel is binding or when interrupting

a cut for any reason, switch off the power

tool and hold the power tool motionless

until the wheel comes to a complete stop.

Never attempt to remove the cut-off wheel

from the cut while the wheel is in motion

otherwise kickback may occur. Investigate

and take corrective action to eliminate the cause

of wheel binding.

d) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed

and carefully reenter the cut. The wheel may

bind, walk up or kickback if the power tool is

restarted in the workpiece.

e) Support panels or any oversized workpiece

to minimize the risk of wheel pinching and

kickback. Large workpieces tend to sag under

their own weight. Supports must be placed

under the workpiece near the line of cut and

near the edge of the workpiece on both sides of

the wheel.

f) Use extra caution when making a “pocket

cut” into existing walls or other blind areas.

The protruding wheel may cut gas or water

pipes, electrical wiring or objects that can cause

kickback.

Safety Warnings Speciﬁ c for Sanding

Operations

a) Do not use excessively oversized sanding

disc paper. Follow manufacturer's

recommendations, when selecting sanding

paper. Larger sanding paper extending beyond

the sanding pad presents a laceration hazard

and may cause snagging, tearing of the disc

or kickback.

Safety Warnings Speciﬁ c for Wire

Brushing Operations

a) Be aware that wire bristles are thrown by

the brush even during ordinary operation.

Do not overstress the wires by applying

excessive load to the brush. The wire bristles

can easily penetrate light clothing and/or skin.

b) If the use of a guard is recommended for

wire brushing, do not allow any interference

of the wire wheel or brush with the guard.

Wire wheel or brush may expand in diameter

due to work and centrifugal forces.

Additional Safety Information

• Threaded mounting of accessories must match

the grinder spindle thread. For accessories

mounted by flanges, the arbor hole of the

accessory must fit the locating diameter of

the flange. Accessories that do not match the

mounting hardware of the power tool will run

out of balance, vibrate excessively and may

cause loss of control.

ENGLISH

36

• The grinding surface of the centre depressed

wheels must be mounted below the plane of

the guard lip. An improperly mounted wheel

that projects through the plane of the guard lip

cannot be adequately protected.

Residual Risks

In spite of the application of the relevant safety

regulations and the implementation of safety

devices, certain residual risks cannot be avoided.

These are:

– Impairment of hearing

– Risk of personal injury due flying particles.

– Risk of burns due to accessories becoming hot

during operation.

– Risk of personal injury due to prolonged use.

– Risk of dust from hazardous substances.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

Wear ear protection.

Wear eye protection.

DATE CODE POSITION (FIG. 1)

The Date Code (p), which also includes the year of

manufacture, is printed into the housing.

Example:

2012 XX XX

Year of Manufacture

Package Contents

The package contains:

1 Angle grinder

1 115 mm guard (D28142, D28143)

1 125 mm guard (D28142)

1 Anti-vibration side handle

1 Flange set

1 Two-pin spanner

1 Instruction manual

1 Exploded drawing

• Check for damage to the tool, parts or

accessories which may have occurred during

transport.

• Take the time to thoroughly read and

understand this manual prior to operation.

Description (ﬁ g. 1, 4)

WARNING: Never modify the power

tool or any part of it. Damage or

personal injury could result.

a. Paddle switch

b. Lock-off lever

c. Spindle lock button

d. Guard

e. Dust Ejection System

f. Anti-vibration side handle

g. Side handle hole

h. Threaded clamp nut

i. Backing flange

INTENDED USE

The D28142 and D28143 heavy duty angle grinders

have been designed for professional grinding, cutting

and sanding applications.

DO NOT use grinding wheels other than centre

depressed wheels and flap-disk.

DO NOT use under wet conditions or in presence of

flammable liquids or gases.

These heavy-duty angle grinders are professional

power tools. DO NOT let children come into

contact with the tool. Supervision is required when

inexperienced operators use this tool.

• This product is not intended for use by persons

(including children) suffering from diminished

physical, sensory or mental abilities; lack of

experience, knowledge or skills unless they are

supervised by a person responsible for their

safety. Children should never be left alone with

this product.

Dust Ejection System

The dust ejection system (e) prevents dust pile-up

around the guard and motor inlet, and minimises the

amount of dust entering the motor housing.

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 60745; therefore no

earth wire is required.

ENGLISH

37

WARNING: 115 V units have to

be operated via a fail-safe isolating

transformer with an earth screen

between the primary and secondary

winding.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

D

EWALT service organization.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in

the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

Using an Extension Cable

If an extension cable is required, use an approved

3–core extension cable suitable for the power input

of this tool (see Technical Data).The minimum

conductor size is 1.5 mm

2

; the maximum length

is 30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off. An accidental start-up can

cause injury.

Attaching Side Handle (ﬁ g. 1)

WARNING: Before using the tool,

check that the handle is tightened

securely.

WARNING: The side handle should

always be used to maintain control of

the tool at all times.

Screw the side handle (f) tightly into one of the holes

(g) on either side of the gear case.

Mounting and Removing the Guard

(ﬁ g. 2)

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off. An accidental start-up can

cause injury.

CAUTION: Guards must be used with

this grinder.

When using the D28142 or the D28143 grinder

with a bonded abrasive wheel for cutting metal or

masonry a Type 1 guard MUST be used. Type 1

guards are available at extra cost from DEWALT

distributors.

NOTE: Please refer to the Grinding and Cutting

Accessory Chart at the end of this section to

show other accessories that can be used with these

grinders.

1. Place the angle grinder on a table, spindle (o)

up.

2. Align the lugs (k) with the notches (l).

3. Press the guard (d) down and rotate it to the

required position.

4. Securely tighten the screw (m).

5. To remove the guard, slacken the screw.

CAUTION: If the guard cannot be

tightened by the adjusting screw, do

not use the tool. To reduce the risk of

personal injury, take the tool and guard

to a service centre to repair or replace

the guard.

Fitting and Removing a Grinding or

Cutting Disc (ﬁ g. 1, 4, 5)

WARNING: Do not use a damaged

disc.

1. Place the tool on a table, guard up.

2. Fit the backing flange (i) correctly onto the

spindle (o) (fig. 4).

3. Place the disc (n) on the backing flange (i).

When fitting a disc with a raised centre, make

sure that the raised centre (j) is facing the

backing flange (i).

4. Screw the threaded clamp nut (h) onto the

spindle (o) (fig. 5):

ENGLISH

38

a. The ring on the threaded clamp nut (h) must

face towards the disc when fitting a grinding

disc (fig. 5A);

b. The ring on the threaded clamp nut (h) must

face away from the disc when fitting a cutting

disc (fig. 5B).

5. Press the spindle lock button (c) and rotate the

spindle (o) until it locks in position.

6. Tighten the threaded clamp nut (h) with the two-

pin spanner supplied.

7. Release the spindle lock.

8. To remove the disc, loosen the threaded clamp

nut (h) with the two-pin spanner.

Fitting and Removing a

Backing Pad/Sanding Sheet (ﬁ g. 1, 5)

1. Place the tool on a table, guard up.

2. Remove the backing flange (i).

3. Place the rubber backing pad correctly onto the

spindle (o).

4. Place the sanding sheet on the rubber backing

pad.

5. Screw the threaded clamp nut (h) onto the

spindle. The ring on the threaded clamp nut (h)

must face towards the rubber backing pad.

6. Press the spindle lock button (c) and rotate the

spindle (o) until it locks in position.

7. Tighten the threaded clamp nut (h) with the two-

pin spanner.

8. Release the spindle lock

9. To remove the rubber backing pad, loosen the

threaded clamp nut (h) wih the two-pin spanner.

Fitting a Wire Cup Brush

Screw the wire cup brush directly onto the spindle

without the use of the spacer and threaded flange.

Prior to Operation

• Install the guard and appropriate disc or wheel.

Do not use excessively worn discs or wheels.

• Be sure the inner and outer flange are mounted

correctly.

• Make sure the disc or wheel rotates in the

direction of the arrows on the accessory and

the tool.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off.

WARNING:

• Ensure all materials to be ground or

cut are secured in place.

• Use clamps or a vice to hold

and support the workpiece to a

stable platform. It is important to

clamp and support the workpiece

securely to prevent the movement

of the workpiece and loss of control.

Movement of the workpiece or loss

of control may create a hazard and

cause personal injury.

• Always wear regular working gloves

while operating this tool.

• The gear case becomes very hot

during use.

• Apply only a gentle pressure to the

tool. Do not exert side pressure on the

disc.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

Proper Hand Position (ﬁ g. 1, 6)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the side

handle (f), with the other hand on the body of the

tool, as shown in figure 6.

ENGLISH

39

Paddle Switch (ﬁ g. 1, 3)

WARNING: Before using the tool,

check that the handle is tightened

securely.

CAUTION: Hold the side handle and

body of the tool firmly to maintain

control of the tool at start up and during

use and until the wheel or accessory

stops rotating. Make sure the wheel has

come to a complete stop be fore laying

the tool down.

NOTE: To reduce unexpected tool movement,

do not switch the tool on or off while under load

conditions. Allow the grinder to run up to full speed

before touching the work surface. Lift the tool from

the surface before turning the tool off. Allow the tool

to stop rotating before putting it down.

1. To turn the tool on, push the lock-off lever (b)

toward the back of the tool, then depress the

paddle switch (a). The tool will run while the

switch is depressed.

2. Turn the tool off by releasing the paddle switch.

WARNING: Do not disable the lock-off

lever. If the lock-off lever is disabled, the

tool may start unexpectedly when it is

laid down.

CAUTION: Allow the tool to reach full

speed before touching tool to the work

surface. Lift the tool from the work

surface before turning the tool off.

Spindle Lock (ﬁ g. 1)

The spindle lock (c) is provided to prevent the

spindle from rotating when installing or removing

wheels. Operate the spindle lock only when the tool

is turned off, unplugged from the power supply, and

has come to a complete stop.

NOTICE: To reduce the risk of damage

to the tool, do not engage the spindle

lock while the tool is operating. Damage

to the tool will result and attached

accessory may spin off possibly

resulting in injury.

To engage the lock, depress the spindle lock button

and rotate the spindle until you are unable to rotate

the spindle further.

Metal Applications

When using the tool in metal applications, make

sure that a residual current device (RCD) has been

inserted to avoid residual risks caused by metal

swarf.

If the power supply is shut off by the RCD, take the

tool to authorised D

EWALT repair agent.

WARNING: In extreme working

conditions, conductive dust can

accumulate inside the machine housing

when working with metal. This can result

in the protective insulation inthe machine

becoming degraded with a potential risk

of an electrical shock.

To avoid build-up of metal swarf inside the machine,

we recommend to clear the ventilation slots on a

daily basis. Refer to Maintenance.

Using Flap Discs

WARNING: Metal dust build-up.

Extensive use of flap discs in metal

applications can result in the increased

potential for electric shock. To reduce

this risk, insert an RCD before use

and clean the ventilation slots daily by

blowing dry compressed air into the

ventilation slots inaccordance with the

below maintenance instructions.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off. An accidental start-up can

cause injury.

Pop-off Brushes

The motor will be automatically shut off indicating

that the carbon brushes are nearly worn out and

that the tool needs servicing. The carbon brushes

are not user-serviceable. Take the tool to an

authorised DEWALT repair agent.

Lubrication

Your power tool requires no additional lubrication.

ENGLISH

40

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

tool; never immerse any part of the tool

into a liquid.

Optional Accessories

WARNING: Since accessories, other

than those offered by DEWALT, have

not been tested with this product, use

of such accessories with this tool could

be hazardous. To reduce the risk of

injury, only DEWALT, recommended

accessories should be used with this

product.

Consult your dealer for further information on the

appropriate accessories.

Protecting the Environment

Separate collection. This product must

not be disposed of with normal

household waste.

Should you ﬁnd one day that your DEWALT product

needs replacement, or if it is of no further use to you,

do not dispose of it with household waste. Make this

product available for separate collection.

Separate collection of used products and

packaging allows materials to be

recycled and used again. Re-use of

recycled materials helps prevent

environmental pollution and reduces

the demand for raw materials.

Local regulations may provide for separate collection

of electrical products from the household, at

municipal waste sites or by the retailer when you

purchase a new product.

D

EWALT provides a facility for the collection and

recycling of DEWALT products once they have

reached the end of their working life. To take

advantage of this service please return your product

to any authorised repair agent who will collect them

on our behalf.

You can check the location of your nearest

authorised repair agent by contacting your local

DEWALT office at the address indicated in this

manual. Alternatively, a list of authorised DEWALT

repair agents and full details of our after-sales

service and contacts are available on the Internet at:

www.2helpU.com.

ENGLISH

41

GUARANTEE

DEWALT is confident of the quality of its

products and offers an outstanding guarantee

for professional users of the product. This

guarantee statement is in addition to and in

no way prejudices your contractual rights as a

professional user or your statutory rights as a

private non-professional user. The guarantee

is valid within the territories of the Member

States of the European Union and the

European Free Trade Area.

• 30 DAY NO RISK SATISFACTION GUARANTEE •

If you are not completely satisfied with the

performance of your DEWALT tool, simply

return it within 30 days, complete with all

original components, as purchased, to

the point of purchase, for a full refund or

exchange. The product must have been

subject to fair wear and tear and proof of

purchase must be produced.

• ONE YEAR FREE SERVICE CONTRACT •

If you need maintenance or service for your

D

EWALT tool, in the 12 months following

purchase, you are entitled to one service free

of charge. It will be undertaken free of charge

at an authorised DEWALT repair agent. Proof

of purchase must be produced. Includes

labour. Excludes accessories and spare parts

unless failed under warranty.

• ONE YEAR FULL WARRANTY •

If your D

EWALT product becomes defective

due to faulty materials or workmanship

within 12 months from the date of purchase,

DEWALT guarantees to replace all defective

parts free of charge or – at our discretion –

replace the unit free of charge provided that:

• The product has not been misused;

• The product has been subject to fair

wear and tear;

• Repairs have not been attempted by

unauthorised persons;

• Proof of purchase is produced;

• The product is returned complete with all

original components.

If you wish to make a claim, contact your

seller or check the location of your nearest

authorised DEWALT repair agent in the

DEWALT catalogue or contact your DEWALT

office at the address indicated in this manual.

A list of authorised DEWALT repair agents and

full details of our after-sales service is available

on the Internet at: www.2helpU.com.

ENGLISH

42

GRINDING AND CUTTING ACCESSORY CHART

Guard Type Accessory Description How to Fit Grinder

TYPE 27

GUARD

Depressed

centre grinding

disc

Type 27 guard

Backing flange

Type 27 depressed

centre wheel

Threaded clamp nut

Flap wheel

Wire wheels

with threaded

nut

Type 27 guard

Wire wheel

Wire cup with

threaded nut

Type 27 guard

Wire brush

Backing pad/

sanding sheet

Type 27 guard

Rubber backing pad

Sanding disc

Threaded clamp nut

ENGLISH

43

GRINDING AND CUTTING ACCESSORY CHART (cont.)

Guard Type Accessory Description How to Fit Grinder

TYPE 1

GUARD

Masonry

cutting wheel,

bonded

Type 1 guard

Backing flange

Cutting wheel

Threaded clamp nut

Masonry

cutting wheel,

bonded

TYPE 1

GUARD

OR

TYPE 27

GUARD

Diamond

cutting wheels

Page is loading ...

Belgique et Black & Decker - DEWALT Dutch Tel: 32 70 220 063 Fax: 32 70 225 585

Luxembourg Nieuwlandlaan 7, IZ Aarschot B156 French Tel: 32 70 220 062 Fax: 32 70 222 441

België en B-3200 Aarschot www.dewalt.be

Luxemburg

Danmark D

EWALT Tlf: 70201511

Sluseholmen 2-4 Fax: 70224910

2450 København SV www.dewalt.dk

Deutschland D

EWALT Tel: 06126-21-1

Richard Klinger Str. 11 Fax: 06126-21-2770

65510 Idstein www.dewalt.de

Ελλάς Black & Decker (Ελλάς) Α.Ε. Τηλ: 30 210 8981-616 www.dewalt.gr

Στράβωνος 7 & Βουλιαγμένης 159 Service: 30 210 8981-616

Γλυφάδα 16674, Αθήνα Φαξ: 30 210 8983-570

España DEWALT Tel: 934 797 400

Parque de Negocios “Mas Blau” Fax: 934 797 419

Edificio Muntadas, c/Bergadá, 1, Of. A6 www.dewalt.es

08820 El Prat de Llobregat (Barcelona)

France D

EWALT Tel: 04 72 20 39 20

5, allée des hêtres Fax: 04 72 20 39 00

BP 30084, 69579 Limonest Cedex www.dewalt.fr

Schweiz DEWALT Tel: 044 - 755 60 70

Suisse In der Luberzen 42 Fax: 044 - 730 70 67

Svizzera 8902 Urdorf www.dewalt.ch

Ireland DEWALT Tel: 00353-2781800

Calpe House Rock Hill Fax: 00353-2781811

Black Rock, Co. Dublin www.dewalt.ie

Italia DEWALT Tel: 800-014353

c/o Energypark Building 03 sud, Via Monza 7/A, Fax: 39 039 9590 317

20871 Vimercate (MB), IT www.dewalt.it

Nederlands Black & Decker - DEWALT Tel: 31 164 283 063

Joulehof 12 Fax: 31 164 283 200

4600 AB Bergen Op Zoom www.dewalt.nl

Norge DEWALT Tel: 45 25 13 00

Postboks 4613, Nydalen Fax: 45 25 08 00

0405 Oslo www.dewalt.no

Österreich DEWALT Tel: 01 - 66116 - 0

Werkzeug Vertriebsges m.b.H Fax: 01 - 66116 - 14

Oberlaaerstrasse 248 www.dewalt.at

A-1230 Wien

Portugal D

EWALT Tel: 214 66 75 00

Centro de Escritórios de Sintra Avenida Almirante Fax: 214 66 75 75

Gago Coutinho, 132/134, Edifício 142710-418 Sintra www.dewalt.pt

2710-418 Lisboa

Suomi D

EWALT Puh: 010 400 430

Tekniikantie 12 Faksi: 0800 411 340

02150 Espoo, Finland www.dewalt.fi

Sverige DEWALT Tel: 031 68 61 00

Box 94 Fax: 031 68 60 08

431 22 Mölndal www.dewalt.se

Türkiye

KALE Hırdavat ve Makina A.Ş. Tel: 0212 533 52 55

Defterdar Mah. Savaklar Cad. No:15 Faks: 0212 533 10 05

Edirnekapı / Eyüp / İSTANBUL 34050 TÜRKİYE www.dewalt.com.tr

United DEWALT Tel: 01753-56 70 55 www.dewalt.co.uk

Kingdom 210 Bath Road; Slough, Berks SL1 3YD Fax: 01753-57 21 12

Middle East D

EWALT Tel: 971 4 8863030

Africa P.O. Box - 17164, Fax: 971 4 8863333

Jebel Ali (South Zone), Dubai, UAE www.dewalt.ae

N234399 10/12

DeWalt D28143 Owner's manual

This manual is also suitable for

DeWalt D28143 Owner's manual

in other languages

Related papers

Other documents