BLACK+DECKER GT4245 Owner's manual

Page is loading ...

3

ENGLISH

(Original instructions)

Intended use

Your Black & Decker hedgetrimmer has been designed for

trimming hedges, shrubs and brambles. This tool is intended

for consumer use only.

Safety instructions

General power tool safety warnings

@

Warning! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions listed below may result in electric

shock, re and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains

operated (corded) power tool or battery operated (cordless)

power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b. Do not operate power tools in explosive atmospheres,

such as in the presence of ammable liquids, gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

c. Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodied plugs

and matching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the inuence

of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal

injury.

b. Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal

injuries.

c. Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or

energising power tools that have the switch on invites

accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d. Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

4

ENGLISH

(Original instructions)

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualied repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Additional power tool safety warnings

@

Warning! Additional safety warnings for hedge

trimmers

u Keep all parts of the body away from the cutter blade.

Do not remove cut material or hold material to be cut

when blades are moving. Make sure the switch is off

when clearing jammed material. A moment of inattention

while operating the tool can result in serious personal

injury.

u Carry the hedge trimmer by the handle with the cutter

blade stopped. When transporting or storing the

hedge trimmer always t the cutting device cover.

Proper handling of the hedge trimmer will reduce possible

personal injury from the cutter blades.

u Hold the power tool by insulated gripping surfaces

only, because the cutter blade may contact hidden

wiring or its own cord. Cutter blades contacting a "live"

wire may make exposed metal parts of the power tool

"live" and could give the operator an electric shock.

u Keep cable away from cutting area. During operation

the cable can be hidden in shrubs and can be accidentally

cut the blades.

u The intended use is described in this instruction manual.

The use of any accessory or attachment or performance

of any operation with this tool other than those recom-

mended in this instruction manual can present a risk of

personal injury and/or damage to property.

u If you have not used a hedge trimmer before, preferably

seek practical instruction by an experienced user in addi-

tion to studying this manual.

u Never touch the blades while the tool is running.

u Never attempt to force the blades to come to a standstill.

u Do not put the tool down until the blades have come to a

complete standstill.

u Regularly check the blades for damage and wear. Do not

use the tool when the blades are damaged.

u Take care to avoid hard objects (e.g. metal wire, railings)

when trimming. Should you accidentally hit any such

object, immediately switch the tool off and check for any

damage.

u Should the tool start to vibrate abnormally, immediately

switch it off and disconnect it from the mains suply then

check for any damage.

u If the tool stalls, immediately switch it off. Disconnect it

from the mains supply before attempting to remove any

obstructions.

u After use, place the blade sheath supplied over the

blades. Store the tool, making sure that the blade is not

exposed.

u Always ensure that all guards are tted when using the

tool. Never attempt to use an incomplete tool or a tool with

unauthorised modications.

u Never allow children to use the tool.

u Be aware of falling debris when cutting the higher sides of

a hedge.

u Always hold the tool with both hands and by the handles

provided.

Safety of others

u This appliance is not intended for use by persons (includ-

ing children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concern-

ing use of the appliance by a person responsible for their

safety.

u Children should be supervised to ensure that they do not

play with the appliance.

Residual risks.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving parts.

u Injuries caused when changing any parts, blades or ac-

cessories.

u Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

u Impairment of hearing.

5

ENGLISH

(Original instructions)

u Health hazards caused by breathing dust developed when

using your tool (example:- working with wood, especially

oak, beech and MDF.)

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured

in accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Labels on tool

The following pictograms are shown on the tool:

:

Warning! To reduce the risk of injury, the user

must read the instruction manual.

O

Wear safety glasses or goggles when operating

this tool.

N

Wear ear protection when operating this tool.

E

Immediately disconnect the cable from the

mains if it is damaged or cut.

R

Do not expose the tool to rain or high humidity.

97

Directive 2000/14/EC guaranteed sound power.

Electrical safety

#

This tool is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

u When using the tool outdoors, only use extension cables

intended for outdoor use. A suitable rated Black & Decker

extension cable of up to 30 m can be used without loss of

power.

u Electric safety can be further improved by using a high-

sensitivity 30 mA residual current device (RCD).

Features

This tool includes some or all of the following features.

1. Trigger switch

2. Front handle bail arm

3. Front handle

4. Guard

5. Blade

6. Cable restraint

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged and that the blade sheath is tted

over the blades.

Warning! Never use the tool without the guard.

Connecting the tool to the mains (g. A)

Unless the tool is tted with a mains cable, you will need to

connect an extension cable to the power inlet.

u Connect the female socket of a suitable extension cable to

the power inlet of the tool.

u Loop the cable through the cable restraint (6) as shown

to prevent the extension cable from becoming detached

during use.

u Insert the mains plug into a mains outlet.

Warning! The extension cable must be suitable for outdoor

use. When using a cable reel, always unwind the cable

completely.

6

ENGLISH

(Original instructions)

Use

Warning! Let the tool work at its own pace. Do not overload.

Switching on and off

Note: For your safety, this tool is equipped with a double

switching system. This system prevents starting the tool

inadvertently and will only allow operation while holding the

tool with both hands.

Switching on (g. B)

u Take hold of the front handle (3) with one hand so that the

front handle bail arm (2) is pushed into the body of the

front handle.

u With the other hand, squeeze the trigger switch (1) to start

the tool.

Switching off

u Release the handle bail arm (2) or the trigger switch (1).

Warning! Never attempt to lock a switch in the on position.

Hints for optimum use

u Start by trimming the top of the hedge. Slightly tilt the tool

(up to 15° relative to the line of cut) so that the blade tips

point slightly towards the hedge (g. C). This will cause

the blades to cut more effectively. Hold the tool at the de-

sired angle and move it steadily along the line of cut. The

double-sided blade allows you to cut in either direction.

u In order to obtain a very straight cut, stretch a piece of

string along the length of the hedge at the desired height.

Use the string as a guideline, cutting just above it. (g. D)

u In order to obtain at sides, cut upwards with the growth.

Younger stems move outwards when the blade cuts

downwards, causing shallow patches in the hedge (g. E).

u Take care to avoid any foreign objects. Especially avoid

hard objects such as metal wire and railings, as these

could damage the blades (g. F).

u Regularly oil the blades.

Guidelines for trimming

u Trim hedges and shrubs with seasonal leaves (new leaves

every year) in June and October.

u Trim evergreens in April and August.

u Trim conifers and other fast growing shrubs every six

weeks from May until October.

Guidelines for trimming (Australia & New Zealand)

u Trim hedges and shrubs with seasonal leaves (new leaves

every year) in December and March.

u Trim evergreens in September and February.

u Trim conifers and other fast growing shrubs every six

weeks from October until March.

Accessories

The performance of your tool depends on the accessory used.

Black & Decker and Piranha accessories are engineered to

high quality standards and designed to enhance the perform-

ance of your tool. By using these accessories you will get the

very best from your tool.

Maintenance

Your Black & Decker corded/cordless appliance/tool has been

designed to operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation depends

upon proper tool care and regular cleaning.

Lubrication oil is available from your Black & Decker dealer

(cat. no. A6102-XJ).

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your appliance/tool/

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

u After use, carefully clean the blades. After cleaning, apply

a lm of light machine oil to prevent the blades from rust-

ing.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new

plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 5 A.

Protecting the environment

Z

Separate collection. This product must not be

disposed of with normal household waste.

Should you nd one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product avail-

able for separate collection.

7

ENGLISH

(Original instructions)

z

Separate collection of used products and packag-

ing allows materials to be recycled and used again.

Re-use of recycled materials helps prevent

environmental pollution and reduces the demand

for raw materials.

Local regulations may provide for separate collection of elec-

trical products from the household, at municipal waste sites or

by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and

recycling of Black & Decker products once they have reached

the end of their working life. To take advantage of this service

please return your product to any authorised repair agent who

will collect them on our behalf.

You can check the location of your nearest authorised repair

agent by contacting your local Black & Decker ofce at

the address indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full details of our

after-sales service and contacts are available on the Internet

at: www.2helpU.com

Technical data

GT5050 (Type 1) GT5055 (Type 1)

Voltage V

AC

230 230

Power input W

500 500

Blade strokes

(no load)

min

-1

1850 1835

Blade length

cm

50 55

Blade gap

mm 22 22

Blade brake time s

<1 <1

Weight

kg 2.7 2.8

GT5560 (Type 1) GT6060 (Type 1)

Voltage V

AC

230 230

Power input W

550 600

Blade strokes

(no load)

min

-1

1870 1840

Blade length

cm

60 60

Blade gap

mm 25 25

Blade brake time s

<1 <1

Weight

kg 2.9 3.0

Level of sound pressure according to EN 60745:

Sound pressure (L

pA

) 74 dB(A), uncertainty (K) 3 dB(A)

Sound power (L

WA

) 94 dB(A), uncertainty (K) 3 dB(A)

Vibration total values (triax vector sum) according to EN 60745:

Vibration emission value (a

h, D

) 2.9 m/s

2

, uncertainty (K) 1.5 m/s

2

8

ENGLISH

(Original instructions)

EC declaration of conformity

MACHINERY DIRECTIVE

OUTDOOR NOISE DIRECTIVE

%

GT5050 / GT5055 / GT5560 / GT6060

Black & Decker declares that these products described under

"technical data" are in compliance with:

2006/42/EC, EN 60745-1, EN 60745-2-15

2000/14/EC, Hedge trimmer 1870 min-1, Annex V

Measured sound power (L

pA

) 94 dB(A)

Uncertainty (K) 3 dB(A)

Guaranteed sound power (L

pA

) 97 dB(A)

Uncertainty (K) 3 dB(A)

These products also comply with directive 2004/108/EC.

For more information, please contact Black & Decker at the

following address or refer to the back of the manual.

The undersigned is responsible for compilation of the technical

le and makes this declaration on behalf of Black & Decker.

_

Kevin Hewitt

Vice-President Global Engineering

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

United Kingdom

22/08/2011

Guarantee

Black & Decker is condent of the quality of its products and

offers an outstanding guarantee. This guarantee statement is

in addition to and in no way prejudices your statutory rights.

The guarantee is valid within the territories of the Member

States of the European Union and the European Free Trade

Area.

If a Black & Decker product becomes defective due to faulty

materials, workmanship or lack of conformity, within 24

months from the date of purchase, Black & Decker guarantees

to replace defective parts, repair products subjected to fair

wear and tear or replace such products to ensure minimum

inconvenience to the customer unless:

u The product has been used for trade, professional or hire

purposes;

u The product has been subjected to misuse or neglect;

u The product has sustained damage through foreign

objects, substances or accidents;

u Repairs have been attempted by persons other than

authorised repair agents or Black & Decker service staff.

To claim on the guarantee, you will need to submit proof of

purchase to the seller or an authorised repair agent. You can

check the location of your nearest authorised repair agent

by contacting your local Black & Decker ofce at the address

indicated in this manual. Alternatively, a list of authorised

Black & Decker repair agents and full details of our after-

sales service and contacts are available on the Internet at:

www.2helpU.com

Please visit our website www.blackanddecker.co.uk to register

your new Black & Decker product and to be kept up to date

on new products and special offers. Further information on the

Black & Decker brand and our range of products is available

at www.blackanddecker.co.uk

Page is loading ...

ENGLISH

Do not forget to register your product!

www.blackanddecker.co.uk/productregistration

Register your product online at www.blackanddecker.co.uk/pro-

ductregistration or send your name, surname and product code to

Black & Decker in your country

.

DEUTSCH

Vergessen Sie nicht, Ihr Produkt registrieren zu lassen!

www.blackanddecker.de/productregistration

Lassen Sie Ihr Produkt unter www.blackanddecker.de/productreg-

istration online registrieren oder schicken Sie Ihren Nachnamen,

Vornamen und den Produktcode an Black & Decker in Ihrem Land.

FRANÇAIS

N’oubliez pas d’enregistrer votre produit !

www.blackanddecker.fr/productregistration

Enregistrez votre produit en ligne sur www.blackanddecker.fr/

productregistration ou envoyez vos nom, prénom et code produit à

Black & Decker dans votre pays.

ITALIANO

Non dimenticate di registrare il prodotto!

www.blackanddecker.it/productregistration

Registrate il prodotto online su www.blackanddecker.it/productreg-

istration o inviate nome, cognome e codice del prodotto al centro

Black & Decker del vostro paese.

NEDERLANDS

Vergeet niet uw product te registreren!

www.blackanddecker.nl/productregistration

U kunt uw product online registreren op www.blackanddecker.nl/pro-

ductregistration of u kunt uw voornaam, achternaam en productcode

opsturen naar Black & Decker in uw land.

ESPAÑOL

¡No olvide registrar su producto!

www.blackanddecker.es/productregistration

Registre su producto on-line en www.blackanddecker.es/produc-

tregistration o envíe su nombre, apellidos y código de producto a

Black & Decker en su país.

PORTUGUÊS

Não se esqueça de registar o seu produto!

www.blackanddecker.pt/productregistration

Registe o seu produto online em www.blackanddecker.pt/productre-

gistration ou envie o seu nome, apelido e código do produto para a

Black & Decker no seu país.

SVENSKA

Glöm inte att registrera produkten!

www.blackanddecker.se/productregistration

Registrera produkten online på www.blackanddecker.se/productre-

gistration

eller skicka namn och produktkod till Black & Decker i landet

du bor i.

NORSK

Ikke glem å registrere produktet ditt!

www.blackanddecker.no/productregistration

Registrer produktet ditt online på www.blackanddecker.no/pro-

ductregistration, eller send ditt navn, etternavn og produktkode til

Black & Decker i ditt eget land.

DANSK

Glem ikke at registrere dit produkt!

www.blackanddecker.dk/productregistration

Registrer dit produkt på internettet på: www.blackanddecker.dk/

productregistration eller send dit navn, efternavn og produktkode til

Black & Decker i dit eget land.

SUOMI

Muistathan rekisteröidä tuotteesi!

www.blackanddecker./productregistration

Rekisteröi tuotteesi verkossa osoitteessa www.blackanddecker./

productregistration tai lähetä etunimesi, sukunimesi ja tuotekoodi

oman maasi Black & Decker -edustajalle.

Ε Λ Λ Η Ν Ι Κ Α

Μην ξεχάσετε να καταχωρίσετε το προϊόν σας!

www.blackanddecker.gr/productregistration

Καταχωρίστε το προϊόν σας σε σύνδεση στη σελίδα www.

blackanddecker.gr/productregistration ή στείλτε το όνομα, επίθετο

σας και τον κωδικό πριονωτός στη Black & Decker στη χώρα σας.

Page is loading ...

BLACK+DECKER GT4245 Owner's manual

BLACK+DECKER GT4245 Owner's manual

in other languages

Related papers

Other documents