Philips CEM250/98 User manual

Philips
Brand
Philips
Model
CEM250/98
Category
Car media receivers
Type
User manual
Register your product and get support at
www.philips.com/welcome
EN User manual
CEM250
3
English
EN
Contents
1 Important 4
Safety 4
Notice 4
2 Your car audio system 6
Introduction 6
What’s in the box 6
Overview of the main unit 7
Overview of the remote control 9
3 Get started 11
Install the car audio 11
Install remote control battery 15
Turn on 16
Set clock 16
4 Listen to radio 17
Tune to a radio station 17
Store radio stations in memory 17
Tune to a preset station 17
Play with RDS 17
5 Use bluetooth devices 20
Pairing bluetooth devices 20
Adjust microphone position 20
Voice dialing 20
Make a call 20
Call waiting 21
Call transfer 21
Terminate call 21
Play audio fi les 21
6 Play audio fi les 22
Play a disc 22
Play from USB/SD/SDHC/MMC device 22
Control play 23
Search for an MP3/WMA track 23
View play information 23
Intro play 24
Shuffl e play 24
Repeat play 24
Connect external sound source 24
7 Adjust sound 25
Adjust volume 25
Mute 25
Turn Dynamic Bass Boost (DBB) on/off 25
Select preset equalizer 25
Other sound settings 25
8 Adjust system settings 26
Set PIN code 26
Set bluetooth connection 26
Select blackout setting 26
Turn demo mode on/off 26
Change button backlight color 26
Select start volume 27
Turn beep sound on/off 27
Turn display scroll on/off 27
Select shock-protect setting 27
Reset 28
9 Additional information 29
Detach the front panel 29
Replace fuse 29
Remove the unit 29
10 Product information 30
11 Troubleshooting 31
About Bluetooth device 32
12 Glossary 33
4
Notice
The making of unauthorized copies of
copy-protected material, including computer
programs, fi les, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offence.
This equipment should not be used for such
purposes.
This apparatus includes these labels:
Class II equipment symbol
This symbol indicates that the apparatus has a
double insulation system.
Recycling
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When you see the crossed-out wheel bin
symbol attached to a product, it means the
product is covered by the European Directive
2002/96/EC:
1 Important
Safety
Read and understand all instructions •
before you use your apparatus. If damage
is caused by failure to follow instructions,
the warranty does not apply.
This apparatus is designed for negative •
ground (earth) 12 V DC operation only.
To ensure safe driving, adjust the volume •
to a safe and comfortable level.
Improper fuses can cause damage or •
fi re. When you need to change the fuse,
consult a professional.
Use only the supplied mounting hardware •
for a safe and secure installation.
To avoid short circuit, do not expose the •
apparatus, remote control or remote
control batteries to rain or water.
Never insert objects into the ventilation •
slots or other openings on the apparatus.
Clean the apparatus and frame with a •
soft, damp cloth. Never use substances
such as alcohol, chemicals or household
cleaners on the apparatus.
Never place any objects other than discs •
into the apparatus.
Never use solvents such as benzene, •
thinner, cleaners available commercially,
or anti-static sprays intended for discs.
Visible and invisible laser radiation when •
open. Avoid exposure to beam.
Risk of damage to the apparatus screen! •
Never touch, push, rub or strike the
screen with any object.
Caution
Use of controls or adjustments or •
performance of procedures other than herein
may result in hazardous radiation exposure or
other unsafe operation.
EN
5
2009 © Koninklijke Philips Electronics N.V. All
rights reserved.
Specifi cations are subject to change without
notice. Trademarks are the property of
Koninklijke Philips Electronics N.V. or their
respective owners. Philips reserves the right
to change products at any time without being
obliged to adjust earlier supplies accordingly.
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products. The correct
disposal of your old product helps prevent
potentially negative consequences on the
environment and human health.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed of with normal household
waste.
Please inform yourself about the local rules on
separate collection of batteries. The correct
disposal of batteries helps prevent potentially
negative consequences on the environment
and human health.
This product complies with the radio
interference requirements of the European
Community.
This product complies with the requirements
of the following directives and guidelines:
2004/108/EC + 2006/95/EC.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and
old equipment.
Any changes or modifi cations made to this
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
English
EN
6
l Quick start guide
m Standard connector
a
c
gh
i
de f
b
k lm
j
2 Your car audio
system
Congratulations on your purchase, and
welcome to Philips! To fully benefi t from the
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With the in-car audio system, you can enjoy
your drive while you listen to:
FM or AM (MW) radio•
Audio from CD or MP3 disc•
Audio from your mobile phone•
Audio from a USB drive•
Audio from a SD/SDHC/MMC card•
Audio from external devices•
Besides, you can make a call, answer and hang
up a call on the audio system.
What’s in the box
Check and identify the contents of your
package:
a Car audio system
b Remote control
c Microphone
d Microphone hold
e Rubber cushion
f Disassembly tool (2 pieces)
g Front panel
h Carrying case for front panel
i Trim plate
j Screw (4 pieces)
k User manual
EN
7
c SOURCE
Select audio source.•
Connect or disconnect bluetooth •
connection.
d
/MUTE
Turn the unit on or off.•
Adjust volume.•
Confi rm selection.•
Enter characters for search.•
Dial phone number.•
Mute or restore the volume.•
Overview of the main unit
a (green/red)
Answer phone (green).•
Dial number (green).•
View call log (green).•
Terminate call (red).•
b
/DBB
Select tuner band. •
Select MP3/WMA folder.•
Scroll up menu.•
Turn on or off Dynamic Bass Boost •
(DBB) sound.
Select RDS program type.•
a
b
d
g
h
i
e
f
s
x
w
u
t
v
r q po nml kj
c
English
EN
8
s /SEARCH
Select tuner band. •
Store radio stations automatically.•
Scroll up or down menu.•
Select MP3/WMA folder.•
Search a track or folder. •
Select RDS program type. •
t Panel power connection
u Disc slot
v
Take disc out.•
w RESET
Restore default settings•
x SD/MMC card slot
e MENU / DISP
Display radio frequency, clock and •
radio program type (if available).
Display track, elapsed time, artist, •
alburm, title, folder, fi le and clock.
Access system menu.•
Access RDS (Radio Data System) •
menu.
f
Return to previous menu.•
Stop search.•
Disable screen blackout.•
g Display panel
h
Unlock the panel•
i USB socket
j External device socket
k 6
Select preset station 6.•
l 5
Select preset station 5.•
m SHUF, 4
Set shuffl e play mode.•
Select preset station 4.•
n 3, REP
Set repeat play mode.•
Select preset station 3.•
o INTRO, 2
Turn intro play on or off.•
Select preset station 2.•
p 1,
Start play•
Pause or resume play.•
Select preset station 1.•
q
/
Tune to a radio station•
Skip/search for MP3/WMA track.•
r EQ/Audio
Select equalizer (EQ) setting.•
Access audio setting menu.•
EN
9
d MENU
Access system menu.•
Access RDS (Radio Data System) •
menu.
e AUDIO
Access audio setting menu.•
f 5/6/7/8/9/0+
Select track or preset radio station.•
Enter phone number.•
g
Answer phone.•
Dial number.•
h 1,
Start play from the beginning of the •
fi rst track.
Pause or resume play.•
Select preset station 1.•
Enter phone number.•
i SHUF, 4
Set shuffl e play mode.•
Select preset station 4.•
Enter phone number.•
j SEL
Confi rm selection.•
k
/
Tune for radio station•
Skip/search for MP3/WMA track.•
Select RDS program type.•
l
Return to previous menu.•
Disable screen blackout. •
m SOURCE
Select audio source.•
n VOLUME +/-
Adjust volume.•
o EQ
Select EQ setting.•
p DBB
Turn on or off Dynamic Bass Boost •
(DBB) sound.
Overview of the remote
control
a /
Tune to a radio station•
Skip/search for a track.•
b
Mute or restore volume.•
c
PWR
Turn the unit on or off.•
a
c
d
e
f
g
b
k
m
n
p
q
r
s
o
j
l
h
i
t
u
English
EN
10
q SEARCH
Set radio station memory •
automatically.
Search a track or folder.•
r DISP
Display radio frequency, clock and •
radio program type (if available).
Display MP3/WMA elapsed time, last •
listened radio frequency, and clock.
s
Terminate call•
t 3, REP
Set repeat play mode.•
Select preset station 3.•
Enter phone number.•
u INTRO, 2
Turn intro play on or off.•
Select preset station 2.•
Enter phone number. •
EN
11
Note on the power supply lead (yellow)
When you connect other devices to this •
apparatus, ensure that the rating of the
car circuit is higher than the total fuse
value of all the connected devices.
Notes on speaker connection
Never connect speaker wires to the •
metal body or chassis of the car.
Never connect speaker wires with stripes •
to one another.
Overview of parts
These are the supplied parts needed to
connect and install this unit.
a In-car audio system
b Sleeve
c Front panel
d Standard connector
e Trim plate
f Rubber cushion
g Disassembly tools
h Screws (4 pieces)
ab
fgh
e
dc
3 Get started
Caution
Use the controls only as stated in this user •
manual.
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model and serial number of your apparatus. The
model number and serial number are on the
bottom of your apparatus. Write the numbers
here:
Model No. __________________________
Serial No. ___________________________
Install the car audio
These instructions are for a typical installation.
However, if your car has different requirements,
make the corresponding adjustment. If you have
any questions regarding installation kits, consult
your Philips car audio dealer.
Caution
This unit is designed for negative ground •
(earth) 12 V DC operation only.
Always install this unit in the car dashboard. •
Other locations can be dangerous as the rear
of the unit heats up during use.
To avoid short-circuit: before you connect,
•
ensure that the ignition is off.
Ensure that you connect the yellow and red
•
power supply leads after all other leads are
connected.
Ensure that all loose leads are insulated with •
electrical tape.
Ensure that the leads do not get caught under •
screws orin parts that will move (e.g. seat rail).
Ensure that all ground (earth) leads are run to •
a common ground (earth) point.
Use only the supplied mounting hardware for a •
safe and secure installation.
Improper fuses can cause damage or fi re. •
When you need to change the fuse, consult a
professional.
English
EN
12
Connector Connect to
1MIC Microphone
2FRONT LINE
OUT R
Front right
speaker
3FRONT LINE
OUT L
Front left
speaker
4 REAR LINE
OUT R
Rear right
speaker
5 REAR LINE
OUT L
Rear left speaker
6SUB OUT Subwoofer
7 ANTENNA Antenna
Connection: for cars without ISO
connectors
Caution
Be sure to connect the black ground (earth) •
lead fi rst.
1 Connect the antenna and amplifi er as
illustrated, if applicable.
Connection: for cars with ISO
connectors
Caution
Ensure that all loose leads are insulated with •
electrical tape.
1 Pull out the ISO connectors from car
dashboard and connect them to the
bigger end of the supplied standard
connector.
2 Connect the other end of the supplied
standard connector to the unit.
3 Connect the antenna and amplifi er as
illustrated, if applicable.
EN
13
1 Green/black strip Left speaker
(Rear)
2 White/black strip Left speaker
(Front)
3Gray/black strip Right speaker
(Front)
4 Purple/black strip Right speaker
(Rear)
eRED Ignition key +12V DC
when ON/ACC
fBLUE Motor/electric
antenna relay control
lead/Amplifi er relay
control lead
gBLACK Ground
h ORANGE/
WHITE
Illumination switch
iYELLOW To the +12V car
battery which is
energized at all times
B
b
a
c
d
aa
b
c
d
a
b
e
f
c
d
g
h
i
b
c
d
Connector Connect to
1MIC Microphone
2FRONT LINE
OUT R
Front right
speaker
3FRONT LINE
OUT L
Front left
speaker
4 REAR LINE
OUT R
Rear right
speaker
5 REAR LINE
OUT L
Rear left speaker
6SUB OUT Subwoofer
7 ANTENNA Antenna
2 Cut off the bigger end of the supplied
standard connector.
3 Check the car’s wiring carefully and
connect them to the supplied standard
connector.
English
EN
14
4 Ensure that car dashboard opening is
within these measurements:
5 Install the sleeve into the dashboard and
bend the tabs outward to fi x the sleeve.
Note
Skip this step if the unit is not fi xed by sleeve •
but by supplied screws.
183 mm
53mm
5mm
4 Connect the supplied standard connector
to the unit.
Mount in the dashboard
1 If the car does not have an on-board
drive or navigation computer, disconnect
the negative terminal of the car battery.
If you disconnect the car battery in •
a car that has an on-board drive or
navigation computer, the computer
may lose its memory.
If the car battery is not disconnected, •
to avoid short-circuit, ensure that
bare wires do not touch each other.
2 Remove the two screws on the top of the
unit.
3 Remove the mounting sleeve with the
supplied disassembly tools.
EN
15
Attach the front panel
1 Attach the trim plate.
2 Insert the right side of the panel in the
chassis until it is correctly engaged.
3 Press the left side of the panel and point
the left hole at the left pillar.
4 Release the panel to engage the left side.
Install remote control battery
Caution
Risk of explosion! Keep batteries away from •
heat, sunshine or fi re. Never discard batteries
in fi re.
Risk of decreased battery life! Never mix •
different brands or types of batteries.
Risk of product damage! When the remote •
control is not used for long periods, remove
the batteries.
Perchlorate Material - special handling may
•
apply. See www.dtsc.ca.gov/hazardouswaste/
perchlorate.
6 Place the supplied rubber cushion over
the end of the mounting bolt.
7 Slide the unit into the dashboard until you
hear a click sound.
8 Reconnect the negative terminal of the
car battery.
5mm
English
EN
16
For fi rst-time use:
1 Remove the protective tab to activate the
remote control battery.
2 Open the battery compartment.
3 Insert 1 CR2025 batteries with correct
polarity (+/-) as indicated.
4 Close the battery compartment.
Turn on
1 Press to turn on the unit.
To turn off the unit, press •
for 3
seconds.
Set clock
1 Press MENU/DISP for 3 seconds.
2 Press or repeatedly until the
currently time is displayed.
3 Turn clockwise to set hour.
4 Press to confi rm.
5 Turn anti-clockwise to set minute.
6 Press to confi rm.
View clock
1 Press MENU/DISP repeatedly until the
clock is displayed.
EN
17
Store radio stations in
memory
You can store up to 6 stations in each band.
Store staions automatically
1 Press SEARCH for 3 seconds.
The six strongest stations of the »
selected band are saved in preset
channels 1-6 automatically.
Store staions manually
1 Tune to a station that you want to store.
2 Press one of the numbered buttons 1 to
6 for 3 seconds.
The station is saved in the selected »
channel.
Tune to a preset station
1 Press or to select band.
2 Press the number button 1 to 6 to select
the preset station.
Play with RDS
The RDS (Radio Data System) function
operates only in areas with FM stations
broadcasting RDS signals. If you tune to an RDS
station, an RDS icon and information about the
presenter, station or program is displayed.
Turn on RDS
Note
By default, the RDS function is off.•
1 Press MENU/DISP for 3 seconds.
4 Listen to radio
Tune to a radio station
1 Press SOURCE repeatedly to select
Tuner.
2 Press or to select band: [FM1],
[FM2], [FM3], [AM1], or [AM2] .
3 Press or to tune to a radio station
manually.
The radio station is broadcast.»
To search for a radio station »
automatically, press SEARCH for 3
seconds.
Select tuner sensitivity
You can adjust the tuner sensitivity if you want
to receive more radio stations or only stations
with strong signal.
1 Press MENU/DISP for over 2 seconds.
2 Press or repeatedly until [LOCAL]
or [ DX] is displayed.
3 Rotate to select a setting:
[ • LOCAL] (local): Only stations with
strong signal can be broadcast.
[ • DX] (distance): Stations with strong
and weak signals can be broadcast.
4 Press to confi rm the selection.
Select stereo/mono broadcasting
For stations with weak signals: to improve the
reception, change to monoaural sound.
1 Press MENU/DISP for 3 seconds.
2 Press or repeatedly until [STEREO]
or [MONO] is displayed.
3 Turn to select a setting:
• [STEREO]: stereo broadcast.
• [MONO]: mono broadcast.
4 Press to confi rm the selection.
English
EN
18
16 WEATHER Weather
17 FINANCE Finance
18 CHILDREN Children’s
programs
19 SOCIAL Social Affairs
20 RELIGION Religion
21 PHONE IN Phone In
22 TRAVEL Travel
23 LEISURE Leisure
24 JAZZ Jazz Music
25 COUNTRY Country Music
26 NATION M National Music
27 OLDIES Oldies Music
28 FOLK M Folk Music
29 DOCUMENT Documentary
30 TEST Alarm Test
31 ALARM Alarm
Store RDS stations
You can store up to six (6) RDS stations in
each FM band in preset channels.
Note
If you have • stored radio stations in the preset
channels (see ‘Store radio stations in memory’
on page 17 ), below operation will replace the
pre-stored stations.
1 Turn on RDS (see ‘Turn on RDS’ on page
17 ).
2 Select band: [FM1], [FM2] or [FM3] .
3 Press SEARCH/ for 3 seconds.
» [AUTO - SCN] or [PTY] is displayed.
4 Press or to select [AUTO - SCN].
5 Press to start searching.
Six RDS stations with strongest signal »
are stored in channel 1 to 6.
2 Turn to select [ RDS ON]:
» [RDS] is displayed.
To turn off the RDS function, repeat •
steps above and choose [RDS OFF].
Select program type
Before tuning to RDS stations, you can select
program type and let the unit search only for
programs of the selected category.
1 Press /SEARCH until [AUTO--SCN] or
[PTY] is displayed.
2 Press or to select [ PTY], then press
/MENU to confi rm.
3 Turn or to select a program type,
then press
/MENU to start searching.
“» PTY SEEK” is displayed.
Item Program type Description
1 NEWS News services
2 AFFAIRS Politics and
current affairs
3 INFO Special
information
programs
4 SPORT Sports
5 EDUCATE Education
and advanced
training
6 DRAMA Radio plays and
literature
7 CULTURE Culture, religion
and society
8 SCIENCE Science
9 VARIED Entertainment
programs
10 POP M Pop music
11 ROCK M Rock music
12 EASY M Light music
13 LIGHT M Light classical
music
14 CLASSICS Classical music
15 OTHER M Special music
programs
EN
19
3 Turn to select a setting:
• [TA ON]: When there is traffi c
announcement, the unit switches
to the tuner mode (regardless of
the current mode) and begins to
broadcast the announcement on
traffi c conditions. When the traffi c
announcement is over, it returns to
the previous mode.
• [TA OFF]: Traffi c announcement
does not cut in.
Set TA volume
When TA (traffi c announcement) signal is
interrupted, the volume can keep at a preset
level. Follow steps below to set TA volume:
1 Press MENU/DISP for 3 seconds.
2 Press or repeatedly until [TA VOL] is
displayed.
3 Turn to select a volume level:
12(minimum) to 45(maximum).
Select alternate frequencies
If the radio signal come from the current
station is poor, you can turn on the AF
(Alternate Frequency) function to let the
unit searches for another station with
stronger signal but with the same program
identifi cation as the current station
automatically.
1 Press MENU/DISP for 3 seconds.
2 Press or repeatedly until [AF] is
displayed.
3 Turn to select a setting:
• [AF ON]: Turn on the AF mode.
• [AF OFF]: Turn off the AF mode.
Set region for AF tuning
You can defi ne AF tuning region:
[REG
ON]
Only stations in the current
region can be tuned to
automatically.
[REG
OFF]
All stations can be tuned to
automatically.
1 Press MENU/DISP for 3 seconds.
2 Press or repeatedly until [REG]
(Regional Radio) is displayed.
3 Turn to select a setting.
Receive traffi c announcement
If you do not want to miss traffi c
announcement during enjoying music, you
can turn on the TA (Traffi c Announcement)
function.
1 Press MENU/DISP for 3 seconds.
2 Press or repeatedly until [TA] is
displayed.
English
EN
20
Sticked it onto the dashboard. •
Or clip it on the sun-shield.•
Voice dialing
You can dial a number by voice if your mobile
phone supports voice dialing.
1 Press for 3 seconds.
» [VOIC DIAL] is displayed.
2 Speak a name stored in contact list stored
in the phone.
The unit repeats the number and calls »
out.
» [NO MATCH] is displayed if the unit
does not recognize a number.
Make a call
1 Press SOURCE repeatedly to select [BT
MUSIC].
2 Press .
3 Press or to select from the following
list:
• [DIAL NUM]: dial a number directly
• [DIALLED]: dialled number
• [MISSED]: missed call
• [RECEIVED]: received call
• [ME PBK]: Phone directory
• [SIM PBK]: SIM card directory
4 Press to confi rm the selection.
5 Use bluetooth
devices
With this car audio system, you can listen
to audio fi les from a player or make a call
if bluetooth connection is available on your
phone or player.
Pairing bluetooth devices
You can pair your bluetooth device with the
unit as follows:
1 Turn on bluetooth function on the device.
2 Setup bluetooth fuction on your device.
3 Select “CEM250” in the pairing list.
4 Enter default password “0000”.
“» [CONNECT]” is displayed on the
panel if pairing succeeds.
Tip
If the paired device is moved beyond the •
operational range, when it is brought back,
please check if the device is still connected
with the system:
. If they are connected, • [Disconnect] (red icon)
is displayed.
. If connection is lost, • [Connect] (green icon) is
displayed. Follow the instruction above to pair
the device with the system again.
Adjust microphone position
For better sound quality in make/receive phone
call through Bluetooth, place the microphone at
a location close to mouth.
1 Make sure the supplied microphone is
connected to the car audio system. (See
“Connect wires” section).
2 Place the microphone at a proper
location. For example,
EN
21
To dial a number directly, select [DIAL NUM].
1 Press 0-9 to enter phone number.
Press •
/ to change a number.
Press •
to reset entered numbers.
2 Press to dial.
To use a number in call log or directory, select
the options other than [DIAL NUM].
1 Turn to select a number from call log
or directory.
2 Press to dial.
Call waiting
If there is another incoming call during call,
[CALL WAITING] fl ashes on the display panel.
1 Press to terminate the present call.
The other call is automatically »
answered.
The fi rst call is terminated.»
Call transfer
You can transfer voice from loudspeaker to
mobile phones during call.
1 Press .
» [TRANSFER] is displayed.
Terminate call
a Press to terminate call.
Play audio fi les
You can listen to audio from a bluetooth device
and control playback with the unit.
1 Press SOURCE repeatedly to select [BT
MUSIC].
To play, press • 1,
.
To pause, press • 1,
again.
English
EN
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34

Philips CEM250/98 User manual

Philips
Brand
Philips
Model
CEM250/98
Category
Car media receivers
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents