Estate Design EFPMH23JG Operating instructions

Brand
Estate Design
Model
EFPMH23JG
Category
Fireplaces
Type
Operating instructions
4
PREPARATION
This
insert has front panel made of
GLASS!
ALWAYS
use
extreme caution
when
handling glass. Failure to do so could result in personal injury or property damage.
NOTE: The electric insert is shipped inside the mantel. Remove all parts and hardware from the
carton and place them on a clean, soft, dry surface. Remove the insert from the mantel. Check the
parts list to make sure nothing is missing. Dispose of packaging materials properly. Please recycle.
Tools required for assembly: Phillips screwdriver (Not included)
PARTS & HARDWARE
Item
Description
Qty
A
Fireplace Mantel
1
B
Wheels
4
C
Wheel Screws
17*
D
Fireplace Insert Screws
5
E
Electric Fireplace Insert
1
F
Remote Control + Battery
1
G
“L” Bracket
1
*1 extra screw is for replacement
ASSEMBLY
STEP 1. Remove the insert from the mantel (A). Turn the mantel over on a soft level surface.
Align the holes in each wheel (B) with the holes in the mantel.
Thread the wheel screws (C) through the holes and into the mantel.
Tighten securely with a Phillips screwdriver. DO NOT OVER-TIGHTEN.
A
LWAYS unplug the fireplace insert before installation, cleaning
, or before
relocating.
Failure to do so could result in
electric shock
,
fire
, or
personal injury
.
A
E
C
B
D
F
G
C
A
B
B
B
5
NOTE: DO NOT attempt to install the insert from the front of the mantel - it will not fit.
STEP
2. With the help of an adult assistant, lift the insert (E) carefully into the back
of the mantel.
DO NOT
drag the unit across the mantel base or insert
shelf, as it could scratch the wood surface.
From the front of the mantel, check to make sure the fireplace insert is properly aligned.
Thread three insert screws (D) through the holes at the top of the insert. Tighten each screw
securely with a screwdriver. DO NOT OVER
-TIGHTEN.
Place the “L” bra
cket (G) in the center of the mantel base so it touches the back of the insert.
Thread two
insert screws (D)
through the lower holes in the “L” bracket and into the mantel base.
Tighten the screws securely with a Phillips screwdriver. DO NOT OVER-TIGHTEN.
WARNING
This fireplace has wheels. NEVER use near stairs or ramps, or on
unlevel surfaces
. Doing so could cause the fireplace to
roll downhill or
down stairs, and cause personal injury or property damage.
REMOTE CONTROL
The remote control operates with one 3V CR2025
Lithium Cell Battery (included).
Remove the protective sheet between the battery and
the contacts in order to operate (see below).
Remote Control Set-up
l Fig. 1: Remove the plastic sheet from the end of the remote control to allow the battery to
touch the electrical contacts. If the sheet is not removed, the remote control will not work.
l Fig. 2: To install or replace the battery, press the button to allow the battery case to slide out.
Position the battery according the drawing, and slide the case back in to the remote.
FIG 1
FIG 2
NEVER dispose of batteries in fire. Failure to observe this precaution may result in an
explosion. Dispose of batteries at your local hazardous material processing center.
ALWAYS
replace the battery in the remote control with the
same type of battery
.
Failure to do so may result in personal injury or property damage.
D
D
E
D
G
  • Page 1 1
  • Page 2 2

Estate Design EFPMH23JG Operating instructions

Brand
Estate Design
Model
EFPMH23JG
Category
Fireplaces
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents