Eurotech CPU-163-15 Owner's manual

CAR

-521-10

Mini

-ITX Carrier Board for COM Express Mini Type 10 Modules

USER MANUAL

1

-0 – 16 May 2018 – CAR-521-10_UserMan_EN_1-0 – ENGLISH

Trademarks

All trademarks and registered trademarks are the property of their respective owners.

Intended audience for this document

This document is intended for system integrators: skilled persons with a thorough knowledge in linking

together different computing systems and software applications physically or functionally, to operate as a

coordinated whole, in compliance with the applicable regulations.

Disclaimer of liability

Eurotech has reviewed the contents of this document to ensure accuracy and consistency with the hardware

and software described.

Always refer to the latest available manual revision available at: www.eurotech.com.

Revision history

Revision

Description

Date

1-0

First release

16 May 2018

CAR-521-10 User Manual 1-0 Contents

3 /

62

CONTENTS

Contents ...................................................................................................................................................................... 3

1 Safety Instructions ............................................................................................................................................. 5

1.1 Safety messages used in this document ................................................................................................. 5

1.1.1 Safety messages for hazards with a high level of risk ............................................................ 5

1.1.2 Safety messages for hazards with a medium level of risk ...................................................... 6

1.1.3 Safety messages for hazards with a low level of risk .............................................................. 6

1.2 Other messages used in this document .................................................................................................. 6

1.2.1 Instructions on how to use the product effectively and avoid any damage ............................ 6

1.3 How to prevent electrostatic discharge.................................................................................................... 7

1.4 How to prevent electrical hazards ........................................................................................................... 7

2 How to receive Technical Assistance............................................................................................................. 9

2.1 How to ask for technical support ............................................................................................................. 9

2.2 How to send a product for repair ............................................................................................................. 9

3 Declaration of Conformity ............................................................................................................................... 10

3.1 CE Marking ............................................................................................................................................ 10

3.2 WEEE compliance ................................................................................................................................. 10

3.3 RoHS compliance .................................................................................................................................. 10

4 Before using the product ................................................................................................................................ 11

5 Product specifications .................................................................................................................................... 12

6 Hardware Installation ....................................................................................................................................... 14

6.1 Board Layout ......................................................................................................................................... 14

6.2 Block Diagram ....................................................................................................................................... 15

6.3 Mechanical Diagram .............................................................................................................................. 16

6.4 Jumper Settings ..................................................................................................................................... 17

6.4.1 USB Power Select ................................................................................................................. 17

6.4.2 USB Mode Select .................................................................................................................. 18

6.4.3 Clear CMOS Data ................................................................................................................. 19

6.4.4 Mini PCIe3 Signal Select ....................................................................................................... 20

6.4.5 Mini PCIe3 Power Select ...................................................................................................... 21

6.4.6 Panel Power Select ............................................................................................................... 22

6.4.7 VCC5_In Power Select ......................................................................................................... 23

6.4.8 Super I/O Enable/Disable ...................................................................................................... 24

6.4.9 LCD/Inverter Power Select .................................................................................................... 25

6.4.10 DIMM signal control............................................................................................................... 26

6.4.11 BIOS Select ........................................................................................................................... 27

6.4.12 DC-in Voltage Level .............................................................................................................. 28

6.4.13 Backlight Brightness Power Select ....................................................................................... 29

6.4.14 LVDS/eDP Signal Select ....................................................................................................... 30

6.5 Rear Panel I/O Ports.............................................................................................................................. 31

6.5.1 DC-in jack .............................................................................................................................. 32

6.5.2 Serial (COM) Ports ................................................................................................................ 33

6.5.3 DisplayPort ............................................................................................................................ 34

6.5.4 RJ45 LAN Port ...................................................................................................................... 35

6.5.5 USB Ports .............................................................................................................................. 36

6.5.6 Audio ..................................................................................................................................... 37

6.6 I/O Connectors ....................................................................................................................................... 38

Contents CAR-521-10 User Manual 1-0

4

/ 62

6.6.1 S/PDIF Connector ................................................................................................................. 38

6.6.2 Cooling Fan Connector ......................................................................................................... 39

6.6.3 Digital I/O Connector ............................................................................................................. 40

6.6.4 LVDS LCD Panel Connector and LCD/Inverter Power Connector ....................................... 41

6.6.5 SATA (Serial ATA) Connector ............................................................................................... 43

6.6.6 LPC connector ....................................................................................................................... 44

6.6.7 Expansion Slots..................................................................................................................... 45

6.6.8 Front Audio Connector .......................................................................................................... 46

6.6.9 Standby Power LED .............................................................................................................. 47

6.6.10 Front Panel Connector .......................................................................................................... 48

6.6.11 COM Express Connector ...................................................................................................... 49

6.6.12 Switches ................................................................................................................................ 51

6.6.13 Serial Interface Connector .................................................................................................... 52

6.6.14 I2C Connector ....................................................................................................................... 53

6.6.15 SMBus Connector ................................................................................................................. 54

6.6.16 HDD Power Connector .......................................................................................................... 55

6.6.17 Battery ................................................................................................................................... 56

6.6.18 Smart Battery Charger Connector (not supported) ............................................................... 57

6.6.19 eDP (Embedded DisplayPort) Connector ............................................................................. 58

Notes ......................................................................................................................................................................... 61

CAR-521-10 User Manual 1-0 Safety Instructions

5 /

62

1 SAFETY INSTRUCTIONS

READ CAREFULLY AND UNDERSTAND THE INSTRUCTIONS AND WARNINGS CONTAINED IN

THIS DOCUMENT BEFORE INSTALLING / USING THE PRODUCT.

KEEP THIS DOCUMENT FOR FUTURE REFERENCE.

To lower the risk of personal injury, electric shock, fire or damage to equipment, observe the

instructions and warnings contained in this document.

Failure to comply with the instructions and warnings contained this document, violates the standards of

safety, design, manufacture, and intended use of the product.

Eurotech assume no liability for any damage caused by failure to observe the instructions and

warnings contained this document.

Whenever you have any doubt regarding the correct understanding of this document, contact the

Eurotech Technical Support (for more information see "How to receive Technical Assistance" on page

9).

1.1 Safety messages used in this document

1.1.1 Safety messages for hazards with a high level of risk

To indicate a hazard with a high level of risk which, if not avoided, will result in death or serious

injury, the following safety message is used; the message also contains the safety instructions to

follow to avoid any hazard:

DANGER

Example:

DANGER

HIGH VOLTAGE INSIDE.

CONTACT WILL CAUSE ELECTRIC SHOCK OR BURN.

Turn OFF and disconnect power before opening the rack.

Safety Instructions CAR-521-10 User Manual 1-0

6

/ 62

1.1.2 Safety messages for hazards with a medium level of risk

To indicate a hazard with a medium level of risk which, if not avoided, could result in death or

serious injury, the following safety message is used; the message also contains the safety

instructions to follow to avoid any hazard:

WARNING

1.1.3 Safety messages for hazards with a low level of risk

To indicate a hazard with a low level of risk which, if not avoided, could result in minor or moderate

injury, the following safety message is used; the message also contains the safety instructions to

follow to avoid any hazard:

CAUTION

1.2 Other messages used in this document

1.2.1 Instructions on how to use the product effectively and avoid any damage

To indicate:

• Instructions on how to use the product effectively

• Instructions on how to avoid damaging the product or third-party property (not related to personal

injury),

the following message is used:

NOTICE

SIGN

(if necessary)

Text with the instructions to follow to complete the specific task

(written with bold characters).

CAR-521-10 User Manual 1-0 Safety Instructions

7 /

62

1.3 How to prevent electrostatic discharge

NOTICE

HOW TO PREVENT DAMAGING ELECTROSTATIC-SENSITIVE DEVICES

The symbol on the left is applied on electrostatic-sensitive devices.

To prevent damaging electrostatic-sensitive devices:

• Handle the electrostatic-sensitive devices in an ESD Protected Area (EPA)

• Observe the appropriate antistatic precautions. For example: use a wrist

strap kept in constant contact with bare skin and attached to ground.

1.4 How to prevent electrical hazards

Before supplying power to the product, observe all the instructions for safety, installation, and

operation.

DANGER

Failure to supply power correctly and failure to follow all safety instructions, may create an

electric shock hazard, which could result in personal injury or loss of life, and may damage

the product or other property.

To prevent electrical hazards:

• Before using the product, carefully read the supplied instructions

• Never operate with wet hands

• Check any power cords for damage before using them

• Use certified power cables. The power cables must meet the power requirements of the

device

•

Position cables with care. Avoid positioning cables in places where they may be trampled

or compressed by objects placed on them

• Verify that power-points and plugs are not damaged. Avoid overloads

• Always disconnect power and discharge the circuits before touching them

• Use a power supply that meets the requirements stated on the identification label of the

product. In case of uncertainties about the required power supply, contact the Eurotech

Technical Support Team (for more information see "How to receive Technical

Assistance" on page 9).

(This page has been intentionally left blank)

CAR-521-10 User Manual 1-0 How to receive Technical Assistance

9 /

62

2 HOW TO RECEIVE TECHNICAL ASSISTANCE

2.1 How to ask for technical support

To ask for technical support, complete the following steps:

1. Go to the Eurotech Global Support Center: https://support.eurotech.com/

2. Submit a support request

3. Wait for the reply from your Support Team with the information you required.

2.2 How to send a product for repair

To send a product for repair, complete the following steps:

1. Go to the Eurotech Global Support Center: https://support.eurotech.com/

2. Submit an RMA request

3. Wait for the reply from the Eurotech RMA Department. It will contain:

o The RMA number

o The shipping information

4. Pack the product adequately using anti-static material and place it in a sturdy box with enough

packing material to protect it from shocks and vibrations

5. Ship the product to Eurotech following the information received from the RMA

Department.

NOTICE

Any product returned to Eurotech that is found to be damaged due to inappropriate packaging

will not be covered by the warranty.

Declaration of Conformity CAR-521-10 User Manual 1-0

10

/ 62

3 DECLARATION OF CONFORMITY

3.1 CE Marking

The product described in this document is CE marked.

Eurotech is not responsible for the use of this product together with equipment (for

example: power supplies, personal computers, etc.) that are not CE marked and not

compliant with the requirements specified in this document.

3.2 WEEE compliance

In compliance with the Directive 2012/19/EU of the European Parliament and of the Council

of 4 July 2012 on waste electrical and electronic equipment (WEEE), the symbol on the

right, shown on the product or within its literature, indicates separate collection for electrical

and electronic equipment (EEE) that has been placed on the market after 2005.

The product described in this document, at the end of its life cycle, must be collected

separately and managed in accordance with the provisions of the current Directive on

waste of electrical and electronic equipment.

Because of the substances present in the product, improper disposal can cause damage to

human health and to the environment.

To avoid any possible legal implications, contact your local waste collection body for full

collect and recycling information.

3.3 RoHS compliance

The product described in this document, including all its components and its sub-assemblies, have

been manufactured in compliance with the Directive 2011/65/EU of the European Parliament and of the

Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and

electronic equipment.

CAR-521-10 User Manual 1-0 Before using the product

11 /

62

4 BEFORE USING THE PRODUCT

NOTICE

PREVENT ELECTROSTATIC DISCHARGE (ESD)

Always prevent electrostatic discharge: electrostatic discharge can damage

your boards, processor, disk drives, add-in boards, and other components.

To prevent electrostatic discharge:

• Handle the electrostatic-sensitive devices in an ESD-protected area

• Observe the appropriate antistatic precautions. For example: use a wrist

strap kept in constant contact with bare skin and attached to ground

Before using the product, setup the following components:

• COMe Type10 Mini CPU module (with Heat Sink, sold separately)

• Storage devices (for example a hard disk drive)

• Keyboard

• Mouse

• Display.

Product specifications CAR-521-10 User Manual 1-0

12

/ 62

5 PRODUCT SPECIFICATIONS

Specification

Description

Graphics

• Display ports

o 1x DisplayPort

o 1x 24-bit single channel LVDS

Audio

• Realtek ALC888 7.1+2-channel High Definition Audio

• Audio outputs: Mic-in/Center+Subwoofer, Line-in/Surround and Line-out

• S/PDIF audio interface

Storage

• 1x SATA 3.0 port with data transfer rate up to 6Gb/s

Digital I/O

• 4x General Purpose Input (GPI)

• 4x General Purpose Output (GPO)

Damage Free

Intelligence

• Legacy Super I/O support (optional)

o Monitors 5V/1.5V/12V/3.3V

o Monitors SIO_Fan

Temperature

• Operating: 0°C to 60°C

• Storage: -20°C to 85°C

Humidity

• 10% to 90%

Rear Panel IO

Ports

• 1x DC-in jack

• 2x DB-9 RS232 serial ports

• 1x DisplayPort

• 1x RJ45 LAN port

• 2x USB 3.0 ports

• 4x USB 2.0 ports

• Audio:

o 1x Line-in/Surround

o 1x Line-out,

o 1x Mic-in/Centre + Subwoofer jacks

I/O Connectors

• 1x eDP connector

• 1x Serial interface for 2 serial ports (TX/RX)

• 1x LVDS LCD panel connector

• 1x LCD/inverter power connector

• 1x 8-bit Digital I/O connector

• 1x Front audio connector for line-out and mic-in jacks

• 1x S/PDIF connector

• 1x SATA 3.0 port

• 1x SATA power connector

• 1x Smart Battery charger connector (not supported)

• 1x LPC connector

• 1x I

2

C connectors

• 1x SMBus connector

• 1x front panel connector

• 2x fan connectors

CAR-521-10 User Manual 1-0 Product specifications

13 /

62

Expansion Slots

• 1x PCIe x1 slot (PCIe 2.0)

• 3x Mini PCIe slots (PCIe 2.0)

o 1x slot supports PCIe and USB signals for cellular modules (full size)

o 1x slot supports PCIe and USB signals (half size)

o 1x slot supports PCIe or mSATA signal (full size)

• 1x SIM card socket

Supported COM

Express Module

• Mini Type 10 Form Factor

ROM Interface

• 1 SPI interface

o Supports up to 64Mbit

Power input

Available options:

• 5 VDC

• 12 VDC

• 19 VDC

PCB

• Dimensions

o Mini-ITX form factor

o 170mm (6.7") x 170mm (6.7")

• Compliance

o PICMG COM Express® R2.1, Type 10

Hardware Installation CAR-521-10 User Manual 1-0

14

/ 62

6 HARDWARE INSTALLATION

6.1 Board Layout

CAR-521-10 User Manual 1-0 Hardware Installation

15 /

62

6.2 Block Diagram

Hardware Installation CAR-521-10 User Manual 1-0

16

/ 62

6.3 Mechanical Diagram

CAR-521-10 User Manual 1-0 Hardware Installation

17 /

62

6.4 Jumper Settings

6.4.1 USB Power Select

JP3 (for USB 0-1) and JP2 (for USB 2-5) are used to select the power of USB ports.

Selecting +5V_standby will allow you to use a USB keyboard to wake up the system.

Important:

If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the +5V_standby

power source of your power supply must support ≥1.5A. For 3 or more USB ports, the

+5V_standby power source of your power supply must support ≥2A.

Hardware Installation CAR-521-10 User Manual 1-0

18

/ 62

6.4.2 USB Mode Select

The JP11 is used to select the USB mode

CAR-521-10 User Manual 1-0 Hardware Installation

19 /

62

6.4.3 Clear CMOS Data

If you encounter the following situations:

a) CMOS data becomes corrupted.

b) You forgot the supervisor or user password.

you can reconfigure the system with the default values stored in the ROM BIOS.

To load the default values stored in the ROM BIOS, follow the steps below:

1. Power-off the system and unplug the power cord.

2. Set JP6 pins 2 and 3 to On. Wait for a few seconds and set JP6 back to its default setting, pins 1

and 2 On.

3. Now plug the power cord and power-on the system.

Hardware Installation CAR-521-10 User Manual 1-0

20

/ 62

6.4.4 Mini PCIe3 Signal Select

The JP12 is used to select the Mini PCIe signal.

Page is loading ...

Eurotech CPU-163-15 Owner's manual

Eurotech CPU-163-15 Owner's manual

Related papers

Other documents