Hampton Bay D11334-SW2 Operating instructions

Brand
Hampton Bay
Model
D11334-SW2
Type
Operating instructions
E
hase of this s
USE AND CAR GUIDE
BELCOURT SWING
Questions, problems, missing parts? Before returning to the store,
call Hampton Bay Customer Service
HAMPTONBAY. COM
1-855-HD-HAMPTON
8 a.m. - 7 p.m., EST , Monday-Friday
a.m. - 6 p.m., EST , Saturday
9
THANK YOU
We appreciate the trust and confidence you have placed in Hampton Bay through the purc . We strive to continually create quality
products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.
Thank you for choosing Hampton Bay!
e strive to continually c
w ing
Model # D11334-SW2
# 1002 556 667
It
e
m
garages, houses, overhanging branches, laundry lines, or electrical wires.
Table of Contents
of Contents
...................................................... 2
Warranty
.......................................... .............................
2
What is Covered
........................................... ..............
2
What is Not Covered....................................................
2
Pre-Assembly.................................................................
3
Planning Assembly
.......................................................
3
Hardware Included
........................................................
3
Package Contents
... ........................................
4
Assembly
......................................... .................................... 5
Care and Cleaning.............................................................
Warranty
...
. THIS WARRANTY DOES NOT APPLY TO COMMERCIAL USE.
Table
S
8
w ing
Safety Information............................ .......................
2
Safety Information
The user of this swing should always inspect it before each use.
It is essential to place this swing on level ground and not less than 6 ft. from any obstruction, such as fences,
Check the tightness of all of the nuts and bolts on a regular basis.
Make sure that the spring hooks are properly secured before each use.
Always remove the canopy in heavy wind conditions, otherwise, the canopy may tip over and cause damage to its parts.
Weight limit is 450 lbs.
2
WHAT IS COVERED
three years.
and the fabric for
5 YEAR RAME A D
YEAR
A R C M ED ARRA Y
3
2
HAMPTONBAY.COM
Pre-Assembly
PLANNING ASSEMBLY
Please
read
this
entire
instruction
manual
prior
to
assembly.
Identify
all
parts
packed
in
the
carton
against
the
parts
list. Remove
all
protective
materials
and
place
the
parts
on
a
non-abrasive
surface
to
avoid
scratching.
Please
contact 1-855-HD-HAMPTON for further assistance.
NOTE: More than one person may be required to
assemble the product.
HARDWARE INCLUDED
NOTE:
15
QQ
2
2
25
2
2
4
4
2
4
4
4
2
4
AA
CC
DD
EE
FF
GG
HH II
JJ
KK
LL MM
NN
OO
RR
SS
BB
BB
JJ
TT
PP
2
2
4
4
M6x30mm Bolt
AA
M6x4
Bolt M6x4
M6x52mm Bolt
0mm
5mm Bolt
M8x
90mm
W
ing Nut
Nut
W
asher
W
asher
M6x10mm
Plastic
M8 Nut
M6 Bolt Cap
M8 Bolt Cap
M6 Nut Cap
M8 Nut Cap
M6x2mm
Plastic
M6x8mm
Plastic
Adjustment K nob
Hex
M8,M6
Description
Part
Quantity
CC
DD
EE
FF
GG
HH
II
K K
MM
NN
OO
PP
RR
SS
TT
LL
QQ
M6
M6
M8
Tools not shown to actual size.
Bolt
M6x4
Hex Bolt
Washer
Washer
Washer
Wrench
Wrench
25
3
Right Back Leg
Pre-Assembly (continued)
SWING PACKAGE CONTEN S
A
B
C
D
E
F
G
H
I
K
L
M
N
P
J
O
Seat Frame
Back Frame
Right Arm
Left Arm
ing BarSw
Canopy Cloth
Front Leg
Left Back Leg
Top Beam
Side Panel
Top Beam Bent Pipe
Top Beam Straight Pipe
Back Leg Connector
Spring Hook
Seat Cushion
T
DescriptionPart
Quantity
B
J
A
C
D
E
F
G
H
I
K
M
N
O
P
L
2
1
1
1
1
2
1
1
1
1
2
2
2
2
1
1
4
HAMPTONBAY.COM
Assembly
Attaching the
Please contact 1-855-HD-HAMPTON for further assistance.
□
LL
HH
EE
NN
JJ
FF
BB
KK
I
G
H
J
N
AA
KK
FF
1
2
□
Attach the side panel (K ) to the right back leg (H) and the
front leg (G)
S
w
Figure 1
Figure 2
Figure 3
Attaching the
ing
S
F
rame
ide
Panel
( ) using M8 washers (HH), hex bolts (EE) and
nuts ( ). Repeat to
assemble the front leg (G) and the left back leg (I) to the top beam
Ensure all bolts are aligned correctly and tighten with the
(TT). Cover the bolts with bolt caps (LL) and the
nuts with nut caps
Attach the back leg connector (N) to the right back leg (H)
and the
See Figure 2.
Ensure all bolts are aligned correctly and tighten with the
hex
using washers (FF) and bolts (AA). Repeat to
attach the side panel (K )
(G). See Figure 3.
Ensure all bolts are aligned correctly and tighten with the
hex wrench
K
H
G
G
I
5
Attach the front leg (G) and the right back leg (H) to the
to the left back leg (I) and front leg
(SS). Cover the bolts with bolt caps (KK).
top beam
( ). See Figure 1.
wrench
(NN).
left back leg (I) using washers (FF) and bolts (BB).
wrench (SS). Cover the bolts with bolt caps (KK).
J
J
JJ
Attach the left arm (D) and right arm (C) to the back frame (B) using
FF
AA
KK
KK
AA
FF
B
D
C
A
FF
KK
CC
FF
CC
KK
E
OO
KK
DD
FF
GG
MM
II
O
Attach the seat frame (A) to the back frame (B) using bolts (AA) and
□
Figure 5
Figure 6
Figure 4
Figure 9
Figure 8
Figure 7
O
Attach the left arm (D) and right arm (C) to the seat frame
FF
AA
KK
Figure 4
Assembly
Attaching the
eat
Attaching
w
ing Bar
S
4
3
□
S
bolts (CC) and washers (FF). See Figure 6.
Ensure all bolts are aligned correctly and tighten with the
wrench (SS). Cover the bolts with bolt caps (KK).
the
washers (FF), plastic washers (II), and nuts (G G ). See figure 7.
Attach the swing bar (E) to the back of the right arm (C) using
washers (FF), and plastic washers (OO). See Figure 8.
Repeat to attach the swing bar (E) to the left arm (D).
Ensure all bolts are aligned correctly and tighten with the
(SS and TT). Cover the bolts with bolt caps (KK).
Attach the spring hooks (O) to the swing bar (E). See Figure 9.
D
C
6
(A) using
bolts (AA) and washers (FF). See Figure 4.
washers (FF). See Figure 5.
bolts (CC),
wrenches
Attach the swing bar (E) to the front of the right arm (C) using bolts (DD),
(Continued)
Figure
H MPTONBAY.COM
Assembly
Attaching the
Please contact 1-855-HD-HAMPTON for further assistance.
□
□
5
6
7
Canopy
Attaching w ing
S
M
L
F
Figure
10
□
□
Insert the top beam bent pipe (L) and the straight pipe (M)
canopy cloth (F).
Attach the top beam bent pipe (L) and straight pipe (M) together.
Insert the assembly into the four corners as shown.
Attach the canopy to the top beam ( ) using bolts (AA), washers
(FF), plastic washers (OO), plastic washers (PP), wing nuts (RR),
and adj ustment knob (QQ). See Figure 11.
Ensure all bolts are aligned correctly and tighten the bolts with
the wrench (SS).
Cover the bolts with bolt caps (KK).
Insert the spring hooks (O) into the top beam holes ( ). See Figure 12.
□
□
Place the seat cushion (P) on the seat.
12
Figure
O
(Continued)
FF
OO
AA
KK
QQ
PP
RR
P
13
Figure
11
F
A
to the
J
J
J
Care and Cleaning
Do not allow water to build up in the frames. This will cause corrosion and possible freeze damage in cold climates.
Use a mild soap and water for normal cleaning. Do not use janitorial or alcohol based cleaners. Some cleaners may be
Rinse with clean water and dry with a soft, absorbent cloth towel
Treat the frame with a liquid wax for maximum protection against UV rays and/or salty, damp air.
marked as natural, but some ingredients may cause discoloration or have an adverse r
Retain this manual for future use.
Questions, problems, missing parts? Before returning to the store,
call Hampton Bay Customer Service
8 a.m.- 7 p.m., EST, Monday-Friday
9 a.m.- 6 p.m.,EST, Saturday
HAMPTONBAY.COM
1-855-HD-HAMPTON
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Hampton Bay D11334-SW2 Operating instructions

Brand
Hampton Bay
Model
D11334-SW2
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents