Detecto 495 Series Operating instructions

Detecto
Brand
Detecto
Model
495 Series
Type
Operating instructions

Detecto 495 Series is a low-profile wheelchair scale designed for weighing patients in wheelchairs. It features a sturdy base with ramp pins for easy access, a column and beam assembly with a handrail for support, and a hanger for attaching the wheelchair. The scale has a capacity of 1000 pounds and a resolution of 0.2 pounds. It is easy to set up and use, and it comes with a one-year warranty.

The Detecto 495 Series is ideal for use in hospitals, clinics, and other healthcare settings. It is also a good choice for home use.

Detecto 495 Series is a low-profile wheelchair scale designed for weighing patients in wheelchairs. It features a sturdy base with ramp pins for easy access, a column and beam assembly with a handrail for support, and a hanger for attaching the wheelchair. The scale has a capacity of 1000 pounds and a resolution of 0.2 pounds. It is easy to set up and use, and it comes with a one-year warranty.

The Detecto 495 Series is ideal for use in hospitals, clinics, and other healthcare settings. It is also a good choice for home use.

Back of beam
B1
A1
A3
1/4-20 Screws (4)
A2
C
B
A
Set-Up Procedure for DETECTO
Model 495 Beam Type
Low-Profile Wheelchair Scale
1. Remove all packing materials.
2. Set scale base on a flat, level surface. Slide ramp pins into T-slots on base;
drop pins into the grooves.
3. Remove 4 (1/4-20) screws from the column bracket (A1). Set aside
(to be used on steps 4 and 5).
4. Set column and beam assembly (B) on column bracket
(A1). Be sure the back of the beam is facing the scale
deck (A). Secure column and beam assembly with
4 (1/4-20) screws. Do not tighten the screws.
5. To attach handrail (C), remove 2 (3/8-16) screws from the top
of weighbridge side. Set the handrail on the weighbridge
side, align holes, reinstall 2 (3/8-16) screws and tighten.
6. If available, place the scale on a table or workbench, otherwise place the scale on floor.
In either case, DO NOT tilt or place scale on it’s side. Next, push bottom of the hanger (B1)
back towards the scale weighbridge (A), lift long lever and the nose iron (A2) up, slide the
hanger (B1) under the nose iron pivot (A3). After the hanger is attached, tighten the 4 (1/4-20)
screws. The scale assembly is now complete.
7. Move upper and lower poise of the beam to “0” zero position.
8. Beam should balance so that the tip end of the beam is centered in a trig loop. If the beam is
not centered, adjust the zero balance screw to the right or left until the beam is in a balanced
position.
9. If the beam does not come to a balanced position, check all mechanical connections in the
scale base assembly and the column and beam assembly. Repeat step 7. The scale should
now be ready for operation.
Back of Beam
Set Upper and Lower Poise
to “0” Position
Zero Balance Screw
Trig Loop
Lift Long Lever
Hanger
B1
A3
A2
T
D
E
T
C
O
E
www.Detecto.com
&02 E. Daugherty, Webb City, MO 64870 USA
Ph: 417-673-4631 or 1-800-641-2008 Fax: 417-673-2153
Technical Support: 1-866-254-8261
e-mail: [email protected]
®
0066-M188-01 Rev F
09/20
Printed in USA
  • Page 1 1
  • Page 2 2

Detecto 495 Series Operating instructions

Detecto
Brand
Detecto
Model
495 Series
Type
Operating instructions

Detecto 495 Series is a low-profile wheelchair scale designed for weighing patients in wheelchairs. It features a sturdy base with ramp pins for easy access, a column and beam assembly with a handrail for support, and a hanger for attaching the wheelchair. The scale has a capacity of 1000 pounds and a resolution of 0.2 pounds. It is easy to set up and use, and it comes with a one-year warranty.

The Detecto 495 Series is ideal for use in hospitals, clinics, and other healthcare settings. It is also a good choice for home use.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents