Bunn-O-Matic iMIX-3S Oatmeal Datasheet

Type
Datasheet

Bunn-O-Matic iMIX-3S Oatmeal is a machine designed to make instant oatmeal. It has three hoppers, each of which can hold a different flavor of oatmeal. The machine also has a 4.3-gallon (16.3L) hot water tank, which is large enough to meet peak serving times. The front of the machine has large, lighted graphics for merchandising, and the key service components are easily accessible through the front, top, and easily removable side panels. The machine also has a spring-loaded, all-metal auger drive system for easy hopper installation, and a front-of-machine set up and calibration.

Bunn-O-Matic iMIX-3S Oatmeal is a machine designed to make instant oatmeal. It has three hoppers, each of which can hold a different flavor of oatmeal. The machine also has a 4.3-gallon (16.3L) hot water tank, which is large enough to meet peak serving times. The front of the machine has large, lighted graphics for merchandising, and the key service components are easily accessible through the front, top, and easily removable side panels. The machine also has a spring-loaded, all-metal auger drive system for easy hopper installation, and a front-of-machine set up and calibration.

Features
Related Products
Item#
Project
Dat e
For current specification sheets and other information, go to www.bunn.com.
Patents Apply
10/11
D5.3a
iMIX Silver Series Oatmeal System
• Serves three instant oatmeals.
Large, lighted front graphics for merchandising.
4.3-gallon (16.3L) hot water tank to meet peak serving times.
Key service components easily accessible through front, top and easily
removable side panels.
Front of machine access to tank drain, dump valves, auger motors and
control board for easy service.
Contemporary styling for striking visual statement.
Spring-loaded, all metal auger drive system for easy hopper installation.
Front-of-machine set up and calibration.
Adjustable drip tray.
Top-hinged design minimizes machine footprint.
Push and hold dispense.
Hot water dispense button allows customers to
adjust oatmeal thickness to their preference.
Model Agency Listing
iMIX-3S Oatmeal
iMIX
®
Silver Series
®
Oatmeal System with 3 Hoppers
iMIX-3S Oatmeal
Dimensions: 33.4”H x 12.5” W x 24.1” D
(84.8cm H x 31.8cm W x 61.2cm D)
Easy Clear
®
EQHP-10
Product No. : 39000.0004
Easy Clear
®
EQHP-10L
Product No. : 39000.0001
BUNN
®
practices continuous product research and improvement. We reserve the right to change specications and product design without notice. Such
revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.
All dimensions shown in inches. Bunn Corporation owns all copyrights relating to materials in this publication. Please contact Bunn Corporation to request permission to reproduce any portion of this publication.
Dimensions & Specifications
Bunn-O-Matic Corporation of Canada - 280 Industrial Pkwy. S. Aurora, Ontario L4G 3T9 • 905-841-2866 • Fax 905-841-2775 • www.bunn.com
CANADA
Model Product # Volts Amps Watts Capacity Cubic Shipping Cord
per hour Measure Weight Attached
iMIX-3S
Oatmeal 38600.6054 120 11.7 1400 4.5 gal / 8.3 ft
3
/ 90 lbs / Yes*
17 litres 0.24 m
3
40.8 kg
*Power cord (NEMA 5-15P) 15 Amp-120V machine only.
Electrical: 120V model requires 2-wires plus ground service rated 120V, single phase, 60 Hz.
Plumbing: 20-100 psi (138-690 kPa) from a
1
/
4
(6.4 mm) or larger supply line. A shut-off valve should be installed in the line
before the unit. Install a regulator in line when pressure is greater than 90 psi to reduce it to 50 psi. Supplied with
1
/
4
(6.4 mm) male are tting.
24.0”
(61.0 cm)
3.5”
(8.9 cm)
6.2”
(15.7 cm)
4.5
(11.4 cm)
4.8
(12.2 cm)
  • Page 1 1
  • Page 2 2

Bunn-O-Matic iMIX-3S Oatmeal Datasheet

Type
Datasheet

Bunn-O-Matic iMIX-3S Oatmeal is a machine designed to make instant oatmeal. It has three hoppers, each of which can hold a different flavor of oatmeal. The machine also has a 4.3-gallon (16.3L) hot water tank, which is large enough to meet peak serving times. The front of the machine has large, lighted graphics for merchandising, and the key service components are easily accessible through the front, top, and easily removable side panels. The machine also has a spring-loaded, all-metal auger drive system for easy hopper installation, and a front-of-machine set up and calibration.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI